Engineering Commons^™

Interactive Effect Of Fixed Time Order Strategies Within A Supply Chain On Actual In-Stock Probabilities, Mangesh S. Chaudhari

Dissertations, Master's Theses and Master's Reports - Open

This report mainly deals with the interactive effect of different in-stock probabilities used by every individual in a supply chain. Based on a simulation for 10,000 weeks, the effects of varying in-stock probabilities are observed. Based on these observations, an individual in a supply chain can take counter measures in order to avoid stock out chances hence maintaining profits.

Evaluation Of Intelligent Compaction Control In The M-189 Reconstruction Project At Iron River, Michigan, Junhong Li

Dissertations, Master's Theses and Master's Reports - Open

This research evaluated an Intelligent Compaction (IC) unit on the M-189 highway reconstruction project at Iron River, Michigan. The results from the IC unit were compared to several traditional compaction measurement devices including Nuclear Density Gauge (NDG), Geogauge, Light Weight Deflectometer (LWD), Dynamic Cone Penetrometer (DCP), and Modified Clegg Hammer (MCH). The research collected point measurements data on a test section in which 30 test locations on the final Class II sand base layer and the 22A gravel layer. These point measurements were compared with the IC measurements (ICMVs) on a point-to-point basis through a linear regression analysis. Poor correlations …

Determing The Effect Of Thermal Treatment Timing On Ultra-High Performance Concrete Beams, Christopher H. Mullen

Dissertations, Master's Theses and Master's Reports - Open

The loss of prestressing force over time influences the long-term deflection of the prestressed concrete element. Prestress losses are inherently complex due to the interaction of concrete creep, concrete shrinkage, and steel relaxation. Implementing advanced materials such as ultra-high performance concrete (UHPC) further complicates the estimation of prestress losses because of the changes in material models dependent on curing regime.

Past research shows compressive creep is "locked in" when UHPC cylinders are subjected to thermal treatment before being loaded in compression. However, the current precasting manufacturing process would typically load the element (through prestressing strand release from the prestressing bed) …

Development Of An In Situ Measurement Device For Obtaining Material Thermal Properties, Mark A. Hepokoski

Dissertations, Master's Theses and Master's Reports - Open

This thesis presents a methodology for measuring thermal properties in situ, with a special focus on obtaining properties of layered stack-ups commonly used in armored vehicle components. The technique involves attaching a thermal source to the surface of a component, measuring the heat flux transferred between the source and the component, and measuring the surface temperature response. The material properties of the component can subsequently be determined from measurement of the transient heat flux and temperature response at the surface alone. Experiments involving multilayered specimens show that the surface temperature response to a sinusoidal heat flux forcing function is also …

Studies Of Functionalized Nanoparticles For Smart Self-Assembly And As Controlled Drug Delivery, Xiaochu Ding

Dissertations, Master's Theses and Master's Reports - Open

This dissertation is related to the studies of functionalized nanoparticles for self-assembly and as controlled drug delivery system. The whole topic is composed of two parts. In the first part, the research was conducted to design and synthesize a new type of ionic peptide-functionalized copolymer conjugates for self-assembly into nanoparticle fibers and 3D scaffolds with the ability of multi-drug loading and governing the release rate of each drug for tissue engineering. The self-assembly study confirmed that such peptide-functionalized amphiphilic copolymers underwent different self-assembly behavior. The bigger nanoparticles were more easily assembled into nanoparticle fibers and 3D scaffolds with larger pore …

Application Of Mfbd Algorithms To Image Reconstruction Under Anisoplanatic Conditions, Glen E. Archer

Dissertations, Master's Theses and Master's Reports - Open

All optical systems that operate in or through the atmosphere suffer from turbulence induced image blur. Both military and civilian surveillance, gun-sighting, and target identification systems are interested in terrestrial imaging over very long horizontal paths, but atmospheric turbulence can blur the resulting images beyond usefulness. My dissertation explores the performance of a multi-frame-blind-deconvolution technique applied under anisoplanatic conditions for both Gaussian and Poisson noise model assumptions. The technique is evaluated for use in reconstructing images of scenes corrupted by turbulence in long horizontal-path imaging scenarios and compared to other speckle imaging techniques. Performance is evaluated via the reconstruction of …

Realization Of A Dc Microgrid Using A Hamiltonian Based Controls Solution, Matthew J. Heath

Dissertations, Master's Theses and Master's Reports - Open

Future power grids are envisioned to be serviced by heterogeneous arrangements of renewable energy sources. Due to their stochastic nature, energy storage distribution and management are pivotal in realizing microgrids serviced heavily by renewable energy assets. Identifying the required response characteristics to meet the operational requirements of a power grid are of great importance and must be illuminated in order to discern optimal hardware topologies. Hamiltonian Surface Shaping and Power Flow Control (HSSPFC) presents the tools to identify such characteristics. By using energy storage as actuation within the closed loop controller, the response requirements may be identified while providing a …

Preliminary Investigation Of Ultra-High Performance Concrete Behavior At High Strain Rates Using The Split-Hopkinson Pressure Bar, Jacob Clark

Dissertations, Master's Theses and Master's Reports - Open

Ultra-high performance concrete (UHPC) displays several enhanced material properties compared to normal strength concrete (NSC). In past research, Split-Hopkinson pressure bar (SHPB) tests have been used for normal strength concrete to determine material behavior at high strain rates. The behavior of advanced concrete materials, such as UHPC, under high strain rates has not been thoroughly investigated. While it is generally accepted that concrete materials experience increases in compressive strength under increasing strain rates, a preliminary investigation was conducted to gain insight into the compressive behavior of UHPC under high strain rate SHPB testing.

In this research, 50 specimens were tested …

Characterization Of A Coal Fly Ash-Cement Slurry By The Absolute Foam Index, Melanie Kueber Watkins

Dissertations, Master's Theses and Master's Reports

This dissertation established a standard foam index: the absolute foam index test. This test characterized a wide range of coal fly ash by the absolute volume of air-entraining admixture (AEA) necessary to produce a 15-second metastable foam in a coal fly ashcement slurry in a specified time. The absolute foam index test was used to characterize fly ash samples having loss on ignition (LOI) values that ranged from 0.17 to 23.3 %wt. The absolute foam index characterized the fly ash samples by absolute volume of AEA, defined as the amount of undiluted AEA solution added to obtain a 15-minute endpoint …

Stochastic Charge Transport In Multi-Island Single-Electron Tunneling Devices, Madhusudan A. Savaikar

Dissertations, Master's Theses and Master's Reports - Open

The physics of the operation of singe-electron tunneling devices (SEDs) and singe-electron tunneling transistors (SETs), especially of those with multiple nanometer-sized islands, has remained poorly understood in spite of some intensive experimental and theoretical research. This computational study examines the current-voltage (IV) characteristics of multi-island single-electron devices using a newly developed multi-island transport simulator (MITS) that is based on semi-classical tunneling theory and kinetic Monte Carlo simulation. The dependence of device characteristics on physical device parameters is explored, and the physical mechanisms that lead to the Coulomb blockade (CB) and Coulomb staircase (CS) characteristics are proposed.

Simulations using …

Terpene And Terpenoid Emissions And Secondary Organic Aerosol Production, Rosa M. Flores

Dissertations, Master's Theses and Master's Reports - Open

Approximately 90% of fine aerosol in the Midwestern United States has a regional component with a sizable fraction attributed to secondary production of organic aerosol (SOA). The Ozark Forest is an important source of biogenic SOA precursors like isoprene (> 150 mg m^-2 d^-1), monoterpenes (10-40 mg m^-2 d^-1), and sesquiterpenes (10-40 mg m^-2d^-1). Anthropogenic sources include secondary sulfate and nitrate and biomass burning (51-60%), vehicle emissions (17-26%), and industrial emissions (16-18%). Vehicle emissions are an important source of volatile and vapor-phase, semivolatile aliphatic and aromatic hydrocarbons that are important …

Induction Of Microalgal Lipids For Biodiesel Production In Tandem With Sequestration Of High Carbon Dioxide Concentration, Wilbel J. Brewer

Dissertations, Master's Theses and Master's Reports - Open

There is no doubt that sufficient energy supply is indispensable for the fulfillment of our fossil fuel crises in a stainable fashion. There have been many attempts in deriving biodiesel fuel from different bioenergy crops including corn, canola, soybean, palm, sugar cane and vegetable oil. However, there are some significant challenges, including depleting feedstock supplies, land use change impacts and food use competition, which lead to high prices and inability to completely displace fossil fuel ^[1-2]. In recent years, use of microalgae as an alternative biodiesel feedstock has gained renewed interest as these fuels are becoming increasingly economically viable, …

Strategic Optimization Techniques For Frtu Deployment And Chip Physical Design, Chen Liao

Dissertations, Master's Theses and Master's Reports - Open

Combinatorial optimization is a complex engineering subject. Although formulation often depends on the nature of problems that differs from their setup, design, constraints, and implications, establishing a unifying framework is essential. This dissertation investigates the unique features of three important optimization problems that can span from small-scale design automation to large-scale power system planning: (1) Feeder remote terminal unit (FRTU) planning strategy by considering the cybersecurity of secondary distribution network in electrical distribution grid, (2) physical-level synthesis for microfluidic lab-on-a-chip, and (3) discrete gate sizing in very-large-scale integration (VLSI) circuit.

First, an optimization technique by cross entropy is proposed to …

Selective Mercury Sequestration From A Silver/Mercury Cyanide Solution, Kristen L. Gabby

Dissertations, Master's Theses and Master's Reports - Open

Silver and mercury are both dissolved in cyanide leaching and the mercury co-precipitates with silver during metal recovery. Mercury must then be removed from the silver/mercury amalgam by vaporizing the mercury in a retort, leading to environmental and health hazards. The need for retorting silver can be greatly reduced if mercury is selectively removed from leaching solutions.

Theoretical calculations were carried out based on the thermodynamics of the Ag/Hg/CN- system in order to determine possible approaches to either preventing mercury dissolution, or selectively precipitating it without silver loss. Preliminary experiments were then carried out based on these calculations to determine …

Electrospun Quaternized Chitosan Fibers For Virus Removal From Drinking Water, Xue Mi

Dissertations, Master's Theses and Master's Reports - Open

Membrane filtration has become an accepted technology for the removal of pathogens from drinking water. Viruses, known to contaminate water supplies, are too small to be removed by a size-exclusion mechanism without a large energy penalty. Thus, functionalized electrospun membranes that can adsorb viruses have drawn our interest. We chose a quaternized chitosan derivative (HTCC) which carries a positively-charged quaternary amine, known to bind negatively-charged virus particles, as a functionalized membrane material. The technique of electrospinning was utilized to produce nanofiber mats with large pore diameters to increase water flux and decrease membrane fouling. In this study, stable, functionalized, electrospun …

Simulating Large Deformation Of Intraneural Ganglion Cyst Using Finite Element Method, Sachin Lokhande

Dissertations, Master's Theses and Master's Reports - Open

Intraneural Ganglion Cyst is disorder observed in the nerve injury, it is still unknown and very difficult to predict its propagation in the human body so many times it is referred as an unsolved history. The treatments for this disorder are to remove the cystic substance from the nerve by a surgery. However these treatments may result in neuropathic pain and recurrence of the cyst. The articular theory proposed by Spinner et al., (Spinner et al. 2003) considers the neurological deficit in Common Peroneal Nerve (CPN) branch of the sciatic nerve and adds that in addition to the treatment, ligation …

Sustainable Energy Production In The United States: Life Cycle Assessment Of Biofuels And Bioenergy, Jiqing Fan

Dissertations, Master's Theses and Master's Reports - Open

The United States of America is making great efforts to transform the renewable and abundant biomass resources into cost-competitive, high-performance biofuels, bioproducts, and biopower. This is the key to increase domestic production of transportation fuels and renewable energy, and reduce greenhouse gas and other pollutant emissions.

This dissertation focuses specifically on assessing the life cycle environmental impacts of biofuels and bioenergy produced from renewable feedstocks, such as lignocellulosic biomass, renewable oils and fats. The first part of the dissertation presents the life cycle greenhouse gas (GHG) emissions and energy demands of renewable diesel (RD) and hydroprocessed jet fuels (HRJ). The …

Production Of Recombinant Trichoderma Reesei Endoglucanase Protein Cel7b By Using Kluyveromyces Lactis, Zainab Ibrahim Alshoug

Dissertations, Master's Theses and Master's Reports - Open

This research is about producing recombinant Trichoderma reesei endoglucanase Cel7B by using Kluyveromyces lactis, transformed with chromosomally integrated Cel7B cDNA, as a host cell (K. lactis Cel7B). Cel7B is one of the glycoside hydrolyze family of proteins that are produced by T. reesei. Cel7B together with other endoglucanases, exoglucanases, and â-glucosidases hydrolyze cellulose to glucose, which can then be fermented to biofuels or other value-added products.

The research objective of this MS project is to examine favorable fermentation conditions for recombinant Cel7B enzyme production and improved activity. Production of enzyme on different types of media was examined, and the activity …

Magneto-Photonic Crystals For Optical Sensing Applications, Neluka Dissanayake

Dissertations, Master's Theses and Master's Reports - Open

Among the optical structures investigated for optical sensing purpose, a significant amount of research has been conducted on photonic crystal based sensors. A particular advantage of photonic crystal based sensors is that they show superior sensitivity for ultra-small volume sensing. In this study we investigate polarization changes in response to the changes in the cover index of magneto-optic active photonic band gap structures. One-dimensional photonic-band gap structures fabricated on iron garnet materials yield large polarization rotations at the band gap edges. The enhanced polarization effects serve as an excellent tool for chemical sensing showing high degree of sensitivity for photonic …

A Novel Approach To Carbon Dioxide Capture And Storage, Brett P. Spigarelli

Dissertations, Master's Theses and Master's Reports - Open

The novel approach to carbon capture and storage (CCS) described in this dissertation is a significant departure from the conventional approach to CCS. The novel approach uses a sodium carbonate solution to first capture CO₂ from post combustion flue gas streams. The captured CO₂ is then reacted with an alkaline industrial waste material, at ambient conditions, to regenerate the carbonate solution and permanently store the CO₂ in the form of an added value carbonate mineral. Conventional CCS makes use of a hazardous amine solution for CO₂ capture, a costly thermal regeneration stage, and the underground storage …

Security Evaluation Of Substation Network Architectures, Pingal Raj Sapkota

Dissertations, Master's Theses and Master's Reports - Open

In recent years, security of industrial control systems has been the main research focus due to the potential cyber-attacks that can impact the physical operations. As a result of these risks, there has been an urgent need to establish a stronger security protection against these threats. Conventional firewalls with stateful rules can be implemented in the critical cyberinfrastructure environment which might require constant updates. Despite the ongoing effort to maintain the rules, the protection mechanism does not restrict malicious data flows and it poses the greater risk of potential intrusion occurrence.

The contributions of this thesis are motivated by the …

Influence Of Mechanical And Thermal Boundary Conditions On Stabilizing/Destabilizing Mechanisms In Evaporating Liquid Films, Aneet Dharmavaram Narendranath

Dissertations, Master's Theses and Master's Reports - Open

Liquid films, evaporating or non-evaporating, are ubiquitous in nature and technology. The dynamics of evaporating liquid films is a study applicable in several industries such as water recovery, heat exchangers, crystal growth, drug design etc. The theory describing the dynamics of liquid films crosses several fields such as engineering, mathematics, material science, biophysics and volcanology to name a few.

Interfacial instabilities typically manifest by the undulation of an interface from a presumed flat state or by the onset of a secondary flow state from a primary quiescent state or both. To study the instabilities affecting liquid films, an evaporating/non-evaporating Newtonian …

The Processing Of Aluminum Gasarites Via Thermal Decomposition Of Interstitial Hydrides, Joseph James Licavoli

Dissertations, Master's Theses and Master's Reports - Open

Gasarite structures are a unique type of metallic foam containing tubular pores. The original methods for their production limited them to laboratory study despite appealing foam properties. Thermal decomposition processing of gasarites holds the potential to increase the application of gasarite foams in engineering design by removing several barriers to their industrial scale production. The following study characterized thermal decomposition gasarite processing both experimentally and theoretically. It was found that significant variation was inherent to this process therefore several modifications were necessary to produce gasarites using this method. Conventional means to increase porosity and enhance pore morphology were studied. Pore …

Computational Prediction Of The Sporulation Network In Clostridium Thermocellum, Changyi Jiang

Dissertations, Master's Theses and Master's Reports - Open

Sporulation is a process in which some bacteria divide asymmetrically to form tough protective endospores, which help them to survive in a hazardous environment for a quite long time. The factors which can trigger this process are diverse. Heat, radiation, chemicals and lacking of nutrition can all lead to the formation of endospores. This phenomenon will lead to low productivity during industrial production. However, the sporulation mechanism in a spore-forming bacterium, Clostridium theromcellum, is still unclear. Therefore, if a regulation network of sporulation can be built, we may figure out ways to inhibit this process. In this study, a …

The Holographic Detector For Clouds From Trl 5 To Trl 8, Matthew Jacob Beals

Dissertations, Master's Theses and Master's Reports - Open

Clouds are one of the most influential elements of weather on the earth system, yet they are also one of the least understood. Understanding their composition and behavior at small scales is critical to understanding and predicting larger scale feedbacks. Currently, the best method to study clouds on the microscale is through airborne in situ measurements using optical instruments capable of resolving clouds on the individual particle level. However, current instruments are unable to sufficiently resolve the scales important to cloud evolution and behavior. The Holodec is a new generation of optical cloud instrument which uses digital inline holography to …

Development Of The Ecocar 3 Proposal And Guidelines For Modeling And Design In Year One Of Ecocar 3, Tyler B. Daavettila

Dissertations, Master's Theses and Master's Reports - Open

This report summarizes the work done for the Vehicle Powertrain Modeling and Design Problem Proposal portion of the EcoCAR3 proposal as specified in the Request for Proposal from Argonne National Laboratory.

The results of the modeling exercises presented in the proposal showed that:

• An average conventional vehicle powered by a combustion engine could not meet the energy consumption target when the engine was sized to meet the acceleration target, due the relatively low thermal efficiency of the spark ignition engine.
  

• A battery electric vehicle could not meet the required range target of 320 km while keeping the vehicle weight below …

  ---

  Go to article

Lattice Boltzmann Method And Cellular Automata Simulation Of Particle Motion And Deposition In 2-D Case, Yichao Deng

Dissertations, Master's Theses and Master's Reports - Open

This technical report discusses the application of the Lattice Boltzmann Method (LBM) and Cellular Automata (CA) simulation in fluid flow and particle deposition. The current work focuses on incompressible flow simulation passing cylinders, in which we incorporate the LBM D2Q9 and CA techniques to simulate the fluid flow and particle loading respectively. For the LBM part, the theories of boundary conditions are studied and verified using the Poiseuille flow test. For the CA part, several models regarding simulation of particles are explained. And a new Digital Differential Analyzer (DDA) algorithm is introduced to simulate particle motion in the Boolean model. …

A Comparative Study Of Heuristic Optimization Algorithms, Rohit A. Bhatia

Dissertations, Master's Theses and Master's Reports - Open

Heuristic optimization algorithms are of great importance for reaching solutions to various real world problems. These algorithms have a wide range of applications such as cost reduction, artificial intelligence, and medicine. By the term cost, one could imply that that cost is associated with, for instance, the value of a function of several independent variables. Often, when dealing with engineering problems, we want to minimize the value of a function in order to achieve an optimum, or to maximize another parameter which increases with a decrease in the cost (the value of this function). The heuristic cost reduction algorithms work …

Manipulation Of Plants By Transformation With Sequences Promoting Cell Division, Victor B. Busov, Steven H. Strauss

Michigan Tech Patents

Polynucleotides encode polypeptides for increasing the rate of growth of plants. Introduction of the polynucleotides into plants produces plants having altered characteristics, such as increased growth, increased leaf area and reduced fertility. Expression of polypeptides in plants or plant cells promotes cell division. Expression of the polynucleotides in plants in the antisense orientation produces plants that are sterile or have smaller leaves.

Me-Em Enewsbrief, December 2012, Department Of Mechanical Engineering-Engineering Mechanics, Michigan Technological University

Department of Mechanical and Aerospace Engineering eNewsBrief

No abstract provided.