Engineering Commons^™

Agent Based, Distributed Control Strategies And Optimization Of Plug-In Electric Vehicles On Smart/Microgrid Architectures, Kyle Bordeau

Dissertations, Master's Theses and Master's Reports - Open

This thesis will present strategies for the use of plug-in electric vehicles on smart and microgrids. MATLAB is used as the design tool for all models and simulations.

First, a scenario will be explored using the dispatchable loads of electric vehicles to stabilize a microgrid with a high penetration of renewable power generation. Grid components for a microgrid with 50% photovoltaic solar production will be sized through an optimization routine to maintain storage system, load, and vehicle states over a 24-hour period. The findings of this portion are that the dispatchable loads can be used to guard against unpredictable losses …

Driver Safety In Far-Side And Far-Oblique Crashes: A Study Of Patrol Vehicles In The United States Of America, Martin Sepoori

Dissertations, Master's Theses and Master's Reports - Open

The dissertation titled "Driver Safety in Far-side and Far-oblique Crashes" presents a novel approach to assessing vehicle cockpit safety by integrating Human Factors and Applied Mechanics. The methodology of this approach is aimed at improving safety in compact mobile workspaces such as patrol vehicle cockpits.

A statistical analysis performed using Michigan state's traffic crash data to assess various contributing factors that affect the risk of severe driver injuries showed that the risk was greater for unrestrained drivers (OR=3.38, p<0.0001) and for incidents involving front and far-side crashes without seatbelts (OR=8.0 and 23.0 respectively, p<0.005). Statistics also showed that near-side and far-side crashes pose similar threat to driver injury severity. A Human Factor survey was conducted to assess various Human-Machine/Human-Computer Interaction aspects in patrol vehicle cockpits. Results showed that tasks requiring manual operation, especially the usage of laptop, would require more attention and potentially cause more distraction. A vehicle survey conducted to evaluate ergonomics-related issues revealed that some of the equipment was in airbag deployment zones. In addition, experiments were conducted to assess the effects on driver distraction caused by changing the position of in-car accessories. A driving simulator study was conducted to mimic HMI/HCI in a patrol vehicle cockpit (20 subjects, average driving experience = 5.35 years, s.d. = 1.8). It was found that the mounting locations of manual tasks did not result in a significant change in response times. Visual displays resulted in response times less than 1.5sec. It can also be concluded that the manual task was equally distracting regardless of mounting positions (average response time was 15 secs). Average speeds and lane deviations did not show any significant results.

Data from 13 full-scale sled tests conducted to simulate far-side impacts at 70 PDOF and 40 PDOF was used to analyze …

Novel Device For Continuous Spatial Control And Temporal Delivery Of Nitric Oxide For In Vitro Cell Culture, Genevieve E. Romanowicz, Weilue He, Matthew Nielsen, Megan C. Frost

Michigan Tech Publications, Part 1

Nitric oxide (NO) is an ubiquitous signaling molecule of intense interest in many physiological processes. Nitric oxide is a highly reactive free radical gas that is difficult to deliver with precise control over the level and timing that cells actually experience. We describe and characterize a device that allows tunable fluxes and patterns of NO to be generated across the surface upon which cells are cultured. The system is based on a quartz microscope slide that allows for controlled light levels to be applied to a previously described photosensitive NO-releasing polydimethylsiloxane (PDMS). Cells are cultured in separate wells that are …

Mse Annual Report 2013, Department Of Materials Science And Engineering, Michigan Technological University

Department of Materials Science and Engineering Annual Reports

Table of Contents

• Paul Sanders, Project-Oriented Learning
• A New Way to Prevent Deadly Infections
• 3D Printers for Peace and Progress
• Faculty and Staff News
• Graduate Student Update
• Outreach
• Undergraduate Student News
• Alumni at a Glance

Ankle Impedance And Ankle Angles During Step Turn And Straight Walk: Implications For The Design Of A Steerable Ankle-Foot Prosthetic Robot, Evandro M. Ficanha

Dissertations, Master's Theses and Master's Reports - Open

During locomotion, turning is a common and recurring event which is largely neglected in the current state-of-the-art ankle-foot prostheses, forcing amputees to use different steering mechanisms for turning, compared to non-amputees. A better understanding of the complexities surrounding lower limb prostheses will lead to increased health and well-being of amputees. The aim of this research is to develop a steerable ankle-foot prosthesis that mimics the human ankle mechanical properties. Experiments were developed to estimate the mechanical impedance of the ankle and the ankles angles during straight walk and step turn. Next, this information was used in the design of a …

A Hydro-Climatic Modeling Framework For Adaptive Water Resources Management In The Great Lakes Basin, Rabi Gyawali

Dissertations, Master's Theses and Master's Reports - Open

This dissertation addresses water resources decision making in the Great Lakes Basin by developing a multi-model framework for climate change impact assessment, including integrated climate and hydrologic modeling. Physically based watershed models, using soil moisture accounting and temperature index (degree-day) snowmelt algorithms, are developed, calibrated and validated to simulate baseflow, snowmelt, and surface runoff under historic conditions. Comparison with an existing model of the Great Lakes basin, the NOAA Large Basin Runoff Model (LBRM), showed improvements resulting from the increased spatial resolution and use of a more process-based snow algorithm in the Hydrologic Engineering Center's Hydrologic Modeling System (HECHMS). As …

Assessment Of Seismic Damage Of Buildings And Related Environmental Impacts, Carley A. Feese

Dissertations, Master's Theses and Master's Reports - Open

Sustainable development has only recently started examining the existing infrastructure, and a key aspect of this is hazard mitigation. To examine buildings under a sustainable perspective requires an understanding of a building's life-cycle environmental costs, including the consideration of associated environmental impacts induced by earthquake damage. Damage repair costs lead to additional material and energy consumption, leading to harmful environmental impacts. Merging results obtained from a seismic evaluation and life-cycle analysis for buildings will give a novel outlook on sustainable design decisions. To evaluate the environmental impacts caused by buildings, long-term impacts accrued throughout a building's lifetime and impacts associated …

Novel Automotive Waste Heat Recovery Techniques, John Randall Armstead

Dissertations, Master's Theses and Master's Reports - Open

The United States transportation industry is predicted to consume approximately 13 million barrels of liquid fuel per day by 2025. If one percent of the fuel energy were salvaged through waste heat recovery, there would be a reduction of 130 thousand barrels of liquid fuel per day. This dissertation focuses on automotive waste heat recovery techniques with an emphasis on two novel techniques.

The first technique investigated was a combination coolant and exhaust-based Rankine cycle system, which utilized a patented piston-in-piston engine technology. The research scope included a simulation of the maximum mass flow rate of steam (700 K and …

An Experimental Investigation Into The Effects Of Biodiesel Blends On Particulate Matter Oxidation In A Catalyzed Particulate Filter During Active Regeneration, James Pidgeon

Dissertations, Master's Theses and Master's Reports - Open

Active regeneration experiments were carried out on a production 2007 Cummins 8.9L ISL engine and associated DOC and CPF aftertreatment system. The effects of SME biodiesel blends were investigated in this study in order to determine the PM oxidation kinetics associated with active regeneration, and to determine the effect of biodiesel on them. The experimental data from this study will also be used to calibrate the MTU-1D CPF model. Accurately predicting the PM mass retained in the CPF and the oxidation characteristics will provide the basis for computation in the ECU that will minimize the fuel penalty associated with active …

Faulted Structures In Li Ion Exchanged Namo2 (M=Ni(0.25)Mn(0.75)), Aaron M. Dewahl

Dissertations, Master's Theses and Master's Reports - Open

A family of LiMO2 materials (M=Ni_0.25Mn_0.75) was prepared from Na_1.2-xLi_xMO_∂ precursors (0≤x≤0.6) via ion exchange. The resulting IE products were examined via XRD and compared to simulated XRD patterns produced using DIFFax to determine the defect structures resulting from the IE process. For the 0.1≤x≤0.6 materials, it is observed that there are 3 LiMO₂ sub-phases with different Li contents present. As the amount of Li in the precursor increases, the amount of each phase changes resulting in a net shift to higher 2-theta; corresponding to an overall decrease in lattice …

A Study Of The Impacts Of Freeze-Thaw On Cliff Recession At The Calvert Cliffs In Calvert County, Maryland, Bonnie Elizabeth Zwissler

Dissertations, Master's Theses and Master's Reports - Open

The Calvert Cliffs, which form much of the western coastline of the Chesapeake Bay in Calvert County, Maryland, are actively eroding and destabilizing, resulting in a critical situation for many homes in close proximity to the slope's crest. Past studies have identified that where waves directly interact with the toe of the slope, wave action controls cliff recession; however, where waves do not regularly interact with the slope toe, the past work identified that freeze-thaw controls recession. This study investigated the validity of this second claim by analyzing the recession rate and freeze-thaw behavior of six study sites along the …

An Investigation Of Waste Glass-Based Geopolymers Supplemented With Alumina, Mary U. Christiansen

Dissertations, Master's Theses and Master's Reports - Open

An increased consideration of sustainability throughout society has resulted in a surge of research investigating sustainable alternatives to existing construction materials. A new binder system, called a geopolymer, is being investigated to supplement ordinary portland cement (OPC) concrete, which has come under scrutiny because of the CO2 emissions inherent in its production.

Geopolymers are produced from the alkali activation of a powdered aluminosilicate source by an alkaline solution, which results in a dense three-dimensional matrix of tetrahedrally linked aluminosilicates. Geopolymers have shown great potential as a building construction material, offering similar mechanical and durability properties to OPC. Additionally, geopolymers have …

Molecular Modeling Of Pmr-15 Polyimide, Fnu Pruthul Kokkada Ravindranath

Dissertations, Master's Theses and Master's Reports - Open

PMR-15 polyimide is a polymer that is used as a matrix in composites. These composites with PMR-15 matrices are called advanced polymer matrix composite that is abundantly used in the aerospace and electronics industries because of its high temperature resistivity. Apart from having high temperature sustainability, PMR-15 composites also display good thermal-oxidative stability, mechanical properties, processability and low costs, which makes it a suitable material for manufacturing aircraft structures. PMR-15 uses the reverse Diels-Alder (RDA) method for crosslinking which provides it with the groundwork for its distinctive thermal stability and a range of 280-300 degree Centigrade use temperature. Regardless of …

Design And Implement Dynamic Programming Based Discrete Power Level Smart Home Scheduling Using Fpga, Xin Yang

Dissertations, Master's Theses and Master's Reports - Open

With the development and capabilities of the Smart Home system, people today are entering an era in which household appliances are no longer just controlled by people, but also operated by a Smart System. This results in a more efficient, convenient, comfortable, and environmentally friendly living environment. A critical part of the Smart Home system is Home Automation, which means that there is a Micro-Controller Unit (MCU) to control all the household appliances and schedule their operating times. This reduces electricity bills by shifting amounts of power consumption from the on-peak hour consumption to the off-peak hour consumption, in terms …

Dysprosium Transport In Nd-Fe-B Pellets, Parawee Pumwongpitak

Dissertations, Master's Theses and Master's Reports - Open

The addition of heavy rare earth (RE) elements to Nd2Fe14B based magnets to form (Nd,Dy)₂Fe₁₄B is known to increase the coercivity and high temperature performance required for hybrid vehicle electric motors and other extreme temperature applications. Attempts to conserve heavy rare earth elements for high temperature (RE)₂Fe₁₄B based magnets have led to the development of a grain boundary diffusion process for bulk magnets. This process relies on transport of a heavy rare earth, such as Dy, into a bulk Nd₂Fe₁₄B magnet along pores, a low volume fraction of …

Two-Phase Flow In Microchannels: Morphology And Interface Phenomena, Alexandru Herescu

Dissertations, Master's Theses and Master's Reports - Open

The existence and morphology, as well as the dynamics of micro-scale gas-liquid interfaces is investigated numerically and experimentally. These studies can be used to assess liquid management issues in microsystems such as PEMFC gas flow channels, and are meant to open new research perspectives in two-phase flow, particularly in film deposition on non-wetting surfaces. For example the critical plug volume data can be used to deliver desired length plugs, or to determine the plug formation frequency. The dynamics of gas-liquid interfaces, of interest for applications involving small passages (e.g. heat exchangers, phase separators and filtration systems), was investigated using high-speed …

Dynamic Model Based State Estimation In A Heavy Duty Diesel Aftertreatment System For Onboard Diagnostics And Controls, Harsha S. Surenahalli

Dissertations, Master's Theses and Master's Reports - Open

Estimating un-measurable states is an important component for onboard diagnostics (OBD) and control strategy development in diesel exhaust aftertreatment systems. This research focuses on the development of an Extended Kalman Filter (EKF) based state estimator for two of the main components in a diesel engine aftertreatment system: the Diesel Oxidation Catalyst (DOC) and the Selective Catalytic Reduction (SCR) catalyst. One of the key areas of interest is the performance of these estimators when the catalyzed particulate filter (CPF) is being actively regenerated.

In this study, model reduction techniques were developed and used to develop reduced order models from the 1D …

Reverse Engineering The Structural And Acoustic Behavior Of A Stradivari Violin, Michael A. Pyrkosz

Dissertations, Master's Theses and Master's Reports - Open

There is a tremendous amount of mystery that surrounds the instruments of Antonio Stradivari. There have been many studies done in the past, but no one completely understands exactly how he made his instruments, or why they are still considered the best in the world. This project is designed to develop an engineering model of one of Stradivari's violins that will accurately simulate the structural and acoustic behavior of the instrument. It also hopes to shine some light on what makes the instruments of Stradivari unique when compared to other violins. It will focus on geometry and material properties, utilizing …

Parametric Study Of Reaxff Simulation Parameters For Molecular Dynamics Modeling Of Reactive Carbon Gases, Benjamin David Jensen

Dissertations, Master's Theses and Master's Reports - Open

Abstract

Optical Waveguides And Structures For Short Haul Optical Communication Channels Within Printed Circuit Boards, Nicholas J. Riegel

Dissertations, Master's Theses and Master's Reports - Open

Optical waveguides have shown promising results for use within printed circuit boards. These optical waveguides have higher bandwidth than traditional copper transmission systems and are immune to electromagnetic interference. Design parameters for these optical waveguides are needed to ensure an optimal link budget. Modeling and simulation methods are used to determine the optimal design parameters needed in designing the waveguides. As a result, optical structures necessary for incorporating optical waveguides into printed circuit boards are designed and optimized.

Embedded siloxane polymer waveguides are investigated for their use in optical printed circuit boards. This material was chosen because it has low …

Intergranular Corrosion And Stress Corrosion Cracking Of Extruded Aa6005a, David James Seguin

Dissertations, Master's Theses and Master's Reports - Open

A research program focused on understanding the intergranular corrosion (IGC) and stress corrosion cracking (SCC) behavior of AA6005A aluminum extrusions is presented in this dissertation. The relationship between IGC and SCC susceptibility and the mechanisms of SCC in AA6005A extrusions were studied by examining two primary hypotheses.

IGC susceptibility of the elongated grain structure in AA6005A exposed to low pH saltwater was found to depend primarily on the morphology of Cu-containing precipitates adjacent to the grain boundaries in the elongated grain structure. IGC susceptibility was observed when a continuous (or semi-continuous) film of Cu-containing phase was present along the grain …

Nanoscale Electrochemistry By In-Situ Transmission Electron Microscopy, Qi Gao

Dissertations, Master's Theses and Master's Reports - Open

Nanoscale research in energy storage has recently focused on investigating the properties of nanostructures in order to increase energy density, power rate, and capacity. To better understand the intrinsic properties of nanomaterials, a new and advanced in situ system was designed that allows atomic scale observation of materials under external fields. A special holder equipped with a scanning tunneling microscopy (STM) probe inside a transmission electron microscopy (TEM) system was used to perform the in situ studies on mechanical, electrical, and electrochemical properties of nanomaterials. The nanostructures of titanium dioxide (TiO2) nanotubes are characterized by electron imaging, diffraction, and chemical …

The Laboratory Evaluation Of Bio Oil Derived From Waste Resources As Extender For Asphalt Binder, Xu Yang

Dissertations, Master's Theses and Master's Reports - Open

A shortage of petroleum asphalt is creating opportunities for engineers to utilize alternative pavement materials. Three types of bio oils, original bio oil (OB), dewatered bio oil (DWB) and polymer-modified bio oil (PMB) were used to modify and partially replace petroleum asphalt in this research. The research investigated the procedure of producing bio oil, the rheological properties of asphalt binders modified and partially replaced by bio oil, and the mechanical performances of asphalt mixtures modified by bio oil. The analysis of variance (ANOVA) is conducted on the test results for the significance analysis. The main finding of the study includes: …

High Voltage Electrophoretic Deposition For Electrochemical Energy Storage And Other Applications, Sunand Santhanagopalan

Dissertations, Master's Theses and Master's Reports - Open

High voltage electrophoretic deposition (HVEPD) has been developed as a novel technique to obtain vertically aligned forests of one-dimensional nanomaterials for efficient energy storage. The ability to control and manipulate nanomaterials is critical for their effective usage in a variety of applications. Oriented structures of one-dimensional nanomaterials provide a unique opportunity to take full advantage of their excellent mechanical and electrochemical properties. However, it is still a significant challenge to obtain such oriented structures with great process flexibility, ease of processing under mild conditions and the capability to scale up, especially in context of efficient device fabrication and system packaging. …

Experimental Investigation Into Particulate Matter Distribution In Catalyzed Particulate Filters Using A 3d Terahertz Wave Scanner, Ryan Kristopher Foley

Dissertations, Master's Theses and Master's Reports - Open

The particulate matter distribution (PM) trends that exist in catalyzed particulate filters (CPFs) after loading, passive oxidation, active regeneration, and post loading conditions are not clearly understood. These data are required to optimize the operation of CPFs, prevent damage to the CPFs caused by non-uniform distributions, and develop accurate CPF models. To develop an understanding of PM distribution trends, multiple tests were conducted and the PM distribution was measured in three dimensions using a terahertz wave scanner. The results of this work indicate that loading, passive oxidation, active regeneration, and post loading can all cause non-uniform PM distributions. The density …

Local Digital Control Of Power Electronic Converters In A Dc Microgrid Based On A-Priori Derivation Of Switching Surfaces, Bibaswan Banerjee

Dissertations, Master's Theses and Master's Reports - Open

In power electronic basedmicrogrids, the computational requirements needed to implement an optimized online control strategy can be prohibitive. The work presented in this dissertation proposes a generalized method of derivation of geometric manifolds in a dc microgrid that is based on the a-priori computation of the optimal reactions and trajectories for classes of events in a dc microgrid. The proposed states are the stored energies in all the energy storage elements of the dc microgrid and power flowing into them. It is anticipated that calculating a large enough set of dissimilar transient scenarios will also span many scenarios not specifically …

Stilling Basin Scour Remediation Using Air Injection And Flat Plate Extension, Rachael Barlock

Dissertations, Master's Theses and Master's Reports - Open

The South Florida Water Management District (SFWMD) is responsible for managing over 2500 miles of waterways and hundreds of water control structures. Many of these control structures are experiencing erosion, known as scour, of the sediment downstream of the structure. Laboratory experiments were conducted in order to investigate the effectiveness of two-dimensional air diffusers and plate extensions (without air injection) on a 1/30 scale model of one of SFWMD gated spillway structures, the S65E gated spillway. A literature review examining the results of similar studies was conducted. The experimental design for this research was based off of previous work done …

Development Of A 1-D Catalyzed Diesel Particulate Filter Model For Simulation Of The Performance And The Oxidation Of Particulate Matter And Nitrogen Oxides Using Passive Oxidation And Active Regeneration Engine Experimental Data, Kiran Premchand

Dissertations, Master's Theses and Master's Reports - Open

Back-pressure on a diesel engine equipped with an aftertreatment system is a function of the pressure drop across the individual components of the aftertreatment system, typically, a diesel oxidation catalyst (DOC), catalyzed particulate filter (CPF) and selective catalytic reduction (SCR) catalyst. Pressure drop across the CPF is a function of the mass flow rate and the temperature of the exhaust flowing through it as well as the mass of particulate matter (PM) retained in the substrate wall and the cake layer that forms on the substrate wall. Therefore, in order to control the back-pressure on the engine at low levels …

Comparative Analysis Of Efficiency And Operating Characteristics Of Automotive Powertrain Architectures Through Chassis Dynamometer Testing, Jeremy J. Anderson

Dissertations, Master's Theses and Master's Reports - Open

The thesis "COMPARATIVE ANALYSIS OF EFFICIENCY AND OPERATING CHARACTERISTICS OF AUTOMOTIVE POWERTRAIN ARCHITECTURES THROUGH CHASSIS DYNAMOMETER TESTING" was completed through a collaborative partnership between Michigan Technological University and Argonne National Laboratory under a contractual agreement titled "Advanced Vehicle Characterization at Argonne National Laboratory". The goal of this project was to investigate, understand and document the performance and operational strategy of several modern passenger vehicles of various architectures. The vehicles were chosen to represent several popular engine and transmission architectures and were instrumented to allow for data collection to facilitate comparative analysis. In order to ensure repeatability and reliability during testing, …

Structural Control Of A Small-Scale Test-Bed Shaker Structure Using A Sponge-Type Magneto-Rheological Fluid Damper, Benjamin D. Winter

Dissertations, Master's Theses and Master's Reports - Open

Semi-active damping devices have been shown to be effective in mitigating unwanted vibrations in civil structures. These devices impart force indirectly through real-time alterations to structural properties. Simulating the complex behavior of these devices for laboratory-scale experiments is a major challenge. Commercial devices for seismic applications typically operate in the 2-10 kN range; this force is too high for small-scale testing applications where requirements typically range from 0-10 N. Several challenges must be overcome to produce damping forces at this level. In this study, a small-scale magneto-rheological (MR) damper utilizing a fluid absorbent metal foam matrix is developed and tested …