Engineering Commons^™

Increasing Access To Pv Technology Through Sustainable Racking: A Review Of Existing Literature And Ground Mounted Fixed Tilt Designs, And What Can Be Done Next, Parijata Prabhakara

Dissertations, Master's Theses and Master's Reports

There is a lack of literature on the structural balance of systems (BOS), also called racking, for ground mount, fixed-tilt solar PV systems. Literature that exists discusses mostly rooftop racking and installations, additional wind loading, and weight considerations imposed on roofs, and little guidance is provided in building codes. The lack of peer-reviewed guidance on design requirements for domestic and large-scale application solar PV racking systems leaves most consumers relying on expensive, patented, off-the-shelf hardware. As PV cell technology and module costs have improved, we can start to focus on PV BOS improvements (particularly racking) and move towards sustainable designs …

Generative Design In Energy Efficient Buildings, Johanna Thill

Dissertations, Master's Theses and Master's Reports

This is an investigative report on the use of generative design and genetic algorithms in the design of energy-efficient buildings. It focuses on a workflow using Project Refinery© and Dynamo© in Revit® for multi-objective optimization and visualization, and Honeybee© for daylighting analysis. The workflow was not about to run completely due to instability in Dynamo, however daylighting analysis and visualizations were produced separately from demonstrations of Refinery. It concludes that while genetic algorithms have potential to be useful in energy-efficient building design, these programs are not yet fully developed and difficult to use without extensive background knowledge and fluency in …

Towards Efficient Water Treatment: Mechanism Of Colloidal Fouling Of Ultrafiltration Membranes, Ikenna Henry Ozofor

Dissertations, Master's Theses and Master's Reports

This research study first reviewed challenges of conventional and membrane separation systems for water treatment. Though membrane separation systems appeared superior to the conventional counterparts for water and wastewater treatment, wider applications of membrane systems have been limited by some factors, most notably is membrane fouling. Experimental studies were therefore conducted to achieve the goal of this research, which is to investigate how feed properties affect fouling of ultrafiltration (UF) membranes by colloids.

Feed salinity, pH, and nanoparticle concentration were the variables studied to unravel how different UF membranes are fouled by model silica colloids (with average diameter of 25nm). …

Virus Purification Framework And Enhancement In Aqueous Two-Phase System, Pratik Umesh Joshi

Dissertations, Master's Theses and Master's Reports

Viral infections regularly pose detrimental health risks to humans. Preventing viral infections through global immunization requires the production of large doses of vaccines. The increasing demand for vaccines, especially during pandemics such as COVID-19, has challenged current manufacturing strategy to develop advanced unit operations with high throughput capability. Over the decade, the upstream processing responsible for synthesizing viral products in cell cultures has shown significant success in yielding high titers of viruses and virus-like particles. The progress in the upstream stage has now shifted the bottleneck to the downstream processing (DSP). Overlooked for decades, the DSP responsible for viral product …

Effect Of Cerium And Magnesium Additions On The Strength And Morphology Of The Intermetallic Compound Layers In Aluminum-Steel Dissimilar Castings, Matt Thomas

Dissertations, Master's Theses and Master's Reports

Dissimilar castings are under investigation due to their light-weighting opportunities within the automotive industry. In this case, dissimilar castings consist of a solid steel core and a poured aluminum component. The strength and integrity of the casting relies on the coherency of the bond between the two components; by optimizing the metallurgical component of the bonding phenomena, the weight and complexity of the insert can be reduced, further increasing the light-weighting opportunities. An interface comprised of intermetallics, generally Fe₄Al₁₃ and Fe₂Al₅, forms between the two components with the latter forming nearest the steel. …

Identification Of Heat Release Shapes And Combustion Control Of An Ltc Engine, Radhika Sitaraman

Dissertations, Master's Theses and Master's Reports

Low Temperature Combustion (LTC) regimes have gained attention in internal combustion engines since they deliver low nitrogen oxides (NOx) and soot emissions with higher thermal efficiency and better combustion efficiency, compared to conventional combustion regimes. However, the operating region of these high-efficiency combustion regimes is limited as it is prone to knocking and high in-cylinder pressure rise rate outside the engine safe zone. By allowing multi-regime operation, high-efficiency region of the engine is extended. To control these complex engines, understanding and identification of heat release rate shapes is essential. Experimental data collected from a 2 liter 4 cylinder LTC engine …

Role Of Flocculation And Dispersion In Pelletization Of Iron Ore, Victor J. Claremboux

Dissertations, Master's Theses and Master's Reports

Traditional modeling of iron ore pellet strength utilizes micromechanical models such as Rumpf’s equation, which correlate attractive forces and pellet properties into an average expected pellet strength. These models combine with repulsive forces within pellets to predict that pellet strength decreases with the introduction of these forces. However, naïvely applying Rumpf’s equation readily leads to incorrect predictions about the resulting behavior. Pellets created with strong repulsive forces arising from dispersion conditions are observed to be significantly stronger overall than pellets formed in the absence of dispersants. A new model is required to understand and predict the effects of these additives …

Efficient Enhancement Of Micro-Nucleation Rates In Flow-Boiling - By Concurrent Micro-Structuring Of The Boiling-Surface And Its Judicious Energization By Piezoelectric-Transducer Induced Acoustic Vibrations., Atharva Rahane

Dissertations, Master's Theses and Master's Reports

The report describes the science and technology backgrounds and uses for the technology breakthrough reported for enhanced flow-boiling based cooling of high-power density electronics (chips, memory etc.). A controlled but explosive growth in micro-scale nucleation rates during flow-boiling of HFE-7100 (electronics and environment friendly liquid from 3M, Inc) is enabled by the uses of inexpensive meshed-copper for micro-structuring of the boiling surface and a pair of Piezoelectric-transducers for active imposition of suitable acoustic vibrations. The pair of piezo transducers mounted just outside the mini-channel impose “in plane” acoustic vibrations of controllable amplitudes and frequencies, and they are used to induce …

Multiphysics Phase Field Modeling Of Electromigration, Zachary Morgan

Dissertations, Master's Theses and Master's Reports

With the miniaturization of microelectronic devices, the reliability of solder interconnects is a significant concern. As size is reduced, the current density flowing through an interconnect becomes larger and exacerbates electromigration leading to microstructural changes and failure. Since most solder alloys are required to be lead-free over toxicity concerns, there are additional challenges to interconnect performance. Nearly all solder alloys are comprised with its majority component being tin due to its low melting temperature and economical cost. The typical metallic white tin phase has a body-centered tetragonal crystal structure which exhibits strong anisotropy in its physical properties. In particular, the …

Innovative Sustainable Wood Preservatives From Pulp And Paper Industry Byproduct, Raisa Carmen Andeme Ela

Dissertations, Master's Theses and Master's Reports

In the modern forest industry, the need for bio-based, renewable, and environmentally-benign wood preservatives is increasing. Preservatives are used to prevent or limit decay and there has been an increasing interest in developing wood preservatives from renewable materials. To support the need for bio-based, environmentally-friendly preservatives, this work employed kraft lignin as a raw material to produce a novel bio-based wood preservative.

For the first project, a statistical design of experiments approach in Minitab® was used to study how fractionation process variables during acid precipitation of lignin influence the lignin mass yield and characteristics. After precipitating lignin from black liquor, …

Developing Innovative Spectral And Machine Learning Methods For Mineral And Lithological Classification Using Multi-Sensor Datasets, Chandan Kumar

Dissertations, Master's Theses and Master's Reports

The sustainable exploration of mineral resources plays a significant role in the economic development of any nation. The lithological maps and surface mineral distribution can be vital baseline data to narrow down the geochemical and geophysical analysis potential areas. This study developed innovative spectral and Machine Learning (ML) methods for mineral and lithological classification. Multi-sensor datasets such as Airborne Visible/Infrared Imaging Spectrometer-Next Generation (AVIRIS-NG), Advanced Spaceborne Thermal Emission and Reflection Radiometer (ASTER), Advanced Land Observing (ALOS) Phased Array type L-band Synthetic Aperture Radar (PALSAR), Sentinel-1, and Digital Elevation Model (DEM) were utilized. The study mapped the hydrothermal alteration minerals derived …

The Overexploitation Of The Valle De Querétaro Aquifer And Its Impact In Small Peri-Urban Communities, Querétaro, México, Kelsey Kirkland

Dissertations, Master's Theses and Master's Reports

The Valle de Querétaro Aquifer is the only viable local water source satisfying the domestic, agricultural, and industrial water needs of the Querétaro Valley. Severe depletion of the groundwater source has had significant consequences throughout the region, especially in the peri-urban communities of Santo Niño de Praga, Tlacote el Bajo, and La Palma. Historically, residents depended on aquifer-fed freshwater springs (known as Los Tajos) to meet their basic and productive needs. Spring production ceased between 10 and 15 ago and investigating the causes formed the basis of this research.

Analysis of available qualitative and quantitative data was used to identify …

High-Performance Spectral Methods For Computer-Aided Design Of Integrated Circuits, Zhiqiang Zhao

Dissertations, Master's Theses and Master's Reports

Recent research shows that by leveraging the key spectral properties of eigenvalues and eigenvectors of graph Laplacians, more efficient algorithms can be developed for tackling many graph-related computing tasks. In this dissertation, spectral methods are utilized for achieving faster algorithms in the applications of very-large-scale integration (VLSI) computer-aided design (CAD)

First, a scalable algorithmic framework is proposed for effective-resistance preserving spectral reduction of large undirected graphs. The proposed method allows computing much smaller graphs while preserving the key spectral (structural) properties of the original graph. Our framework is built upon the following three key components: a spectrum-preserving node aggregation and …

Rain Generated Lahars Prior To The 2018 Catastrophic Eruption Of Fuego Volcano, Guatemala, Claudia Buondonno

Dissertations, Master's Theses and Master's Reports

Fuego volcano is one of the most active and hazardous volcanoes in the world. It is located in the northern part of the Central American Volcanic Arc in Guatemala and its activity can be characterized by long term, low-level background activity, and sporadic larger explosive eruptions. Its historical observations of eruptions date back to 1531, but it has been erupting vigorously since 2002 with major activity throughout 2018, producing three main eruptions in February, June and November. Its almost persistent activity generates major ashfalls, pyroclastic flows, lava flows; when heavy rains mobilize its deposits, they can form damaging lahars. Phenomena, …

Electrospun Nanofiber Scaffolds As A Platform For Breast Cancer Research, Carolynn Que

Dissertations, Master's Theses and Master's Reports

Tumorigenesis is a complex process involving numerous cellular signaling cascades and environmental factors. Here, we report the fabrication of 3D scaffolds with different morphologies obtained by to study cancer cell proliferation and migration. Using an FDA approved, biocompatible and biodegradable polymer Polycaprolactone (PCL), we electrospun nanofiber scaffolds having mesh, aligned, and honeycomb morphologies. The role of the morphology and cellular preferences to nutrition in cell adhesion and proliferation was assessed using scaffolds obtained by electrospinning PCL with fluorescent fructose-like molecular probes. Cell viability, cell morphology, localized cellular growth as related to scaffold morphology and availability of the fructose-like molecular probes …

Sensor Fusion And Non-Linear Mpc Controller Development Studies For Intelligent Autonomous Vehicular Systems, Ahammad Basha Dudekula

Dissertations, Master's Theses and Master's Reports

The demand for safety and fuel efficiency on ground vehicles and advancement in embedded systems created the opportunity to develop Autonomous controller. The present thesis work is three fold and it encompasses all elements that are required to prototype the autonomous intelligent system including simulation, state handling and real time implementation. The Autonomous vehicle operation is mainly dependent upon accurate state estimation and thus a major concern of implementing the autonomous navigation is obtaining robust and accurate data from sensors. This is especially true, in case of Inertial Measurement Unit (IMU) sensor data. The IMU consists of a 3-axis gyro, …

Aperture-Level Simultaneous Transmit And Receive (Star) With Digital Phased Arrays, Ian Cummings

Dissertations, Master's Theses and Master's Reports

In the signal processing community, it has long been assumed that transmitting and receiving useful signals at the same time in the same frequency band at the same physical location was impossible. A number of insights in antenna design, analog hardware, and digital signal processing have allowed researchers to achieve simultaneous transmit and receive (STAR) capability, sometimes also referred to as in-band full-duplex (IBFD). All STAR systems must mitigate the interference in the receive channel caused by the signals emitted by the system. This poses a significant challenge because of the immense disparity in the power of the transmitted and …

Mo6s8-Based Single-Metal-Atom Catalysts For Methanol Synthesis From Steam Reforming Of Methane, H. T. Zhang Zhang

Dissertations, Master's Theses and Master's Reports

The surge of methane as the major component of natural gas and a dominant greenhouse gas calls for the development of efficient strategy to convert it into valuable liquid chemicals such as methanol. However, the current industrial method for methanol synthesis, which consists of the stream reforming of methane (SRM) to syngas and the followed reaction of syngas to methanol, is rather energy-intensive. Direct conversion of methane into methanol (DMTM) is highly desirable in terms of energy efficiency and economy. DMTM with water as oxidant, i.e. SRM to methanol, is a promising solution but the development highly efficient and selective …

A Review Of Open Source Ventilators For Covid-19 And Future Pandemics., Joshua M. Pearce

Michigan Tech Publications, Part 1

Coronavirus Disease 2019 (COVID-19) threatens to overwhelm our medical infrastructure at the regional level causing spikes in mortality rates because of shortages of critical equipment, like ventilators. Fortunately, with the recent development and widespread deployment of small-scale manufacturing technologies like RepRap-class 3-D printers and open source microcontrollers, mass distributed manufacturing of ventilators has the potential to overcome medical supply shortages. In this study, after providing a background on ventilators, the academic literature is reviewed to find the existing and already openly-published, vetted designs for ventilators systems. These articles are analyzed to determine if the designs are open source both in …

How To Achieve Efficiency And Accuracy In Discrete Element Simulation Of Asphalt Mixture: A Drf-Based Equivalent Model For Asphalt Sand Mortar, Yu Liu, Peifeng Su, Miaomiao Li, Hui Yao, Junfu Liu, Mei Xu, Xiaodong Zhou, Zhanping You

Michigan Tech Publications, Part 1

The clump-based discrete element model is one of the asphalt mixture simulation methods, which has the potential to not only predict mixture performance but also simulate particle movement during compaction, transporting, and other situations. However, modelling of asphalt sand mortar in this method remains to be a problem due to computing capacity. Larger-sized balls (generally 2.0-2.36 mm) were usually used to model the smaller particles and asphalt binder, but this replacement may result in the mixture's unrealistic volumetric features. More specifically, replacing original elements with equal volume but larger size particles will increase in buck volume and then different particle …

Primal-Dual 2-Approximation Algorithm For The Monotonic Multiple Depot Heterogeneous Traveling Salesman Problem, S. Rathinam, R. Ravi, J. Bae, K. Sundar

Michigan Tech Publications, Part 1

We study a Multiple Depot Heterogeneous Traveling Salesman Problem (MDHTSP) where the cost of the traveling between any two targets depends on the type of the vehicle. The travel costs are assumed to be symmetric, satisfy the triangle inequality, and are monotonic, i.e., the travel costs between any two targets monotonically increases with the index of the vehicles. Exploiting the monotonic structure of the travel costs, we present a 2-approximation algorithm based on the primal-dual method.

From Open Access To Open Science: The Path From Scientific Reality To Open Scientific Communication, Christian Heise, Joshua M. Pearce

Michigan Tech Publications, Part 1

Although opening up of research is considered an appropriate and trend-setting model for future scientific communication, it can still be difficult to put open science into practice. How open and transparent can a scientific work be? This article investigates the potential to make all information and the whole work process of a qualification project such as a doctoral thesis comprehensively and freely accessible on the internet with an open free license both in the final form and completely traceable in development. The answer to the initial question, the self-experiment and the associated demand for openness, posed several challenges for a …

Copper-Rich “Halo” Off Lake Superior's Keweenaw Peninsula And How Mass Mill Tailings Dispersed Onto Tribal Lands, W. Charles Kerfoot, Noel Urban, Jaebong Jeong, Carol Maclennan, Sophia Ford

Michigan Tech Publications, Part 1

Over a century ago, shoreline copper mills sluiced more than 64 million metric tonnes of tailings into Lake Superior, creating a “halo” around the Keweenaw Peninsula with a buried copper peak. Here we examine how tailings from one of the smaller mills (Mass Mill, 1902–1919) spread as a dual pulse across southern Keweenaw Bay and onto tribal L'Anse Indian Reservation lands. The fine (“slime clay”) fraction dispersed early and widely, whereas the coarse fraction (stamp sands) moved more slowly southward as a black sand beach deposit, leaving scattered residual patches. Beach stamp sands followed the path of sand eroding from …

Agile Stage-Gate Management (Asgm) For Physical Products, John J. Salvato, Andre O. Laplume

Michigan Tech Publications, Part 1

We present a qualitative study of Agile Stage-Gate Management (ASGM),: a hybrid new product development methodology that combines Agile and Stage-Gate Management (SGM) approaches for the coordination of new product development. When applied to software projects, Agile is expected to deliver reduced development times, improved resource utilization, and greater financial success. We examine whether ASGM practitioners realize similar outcomes in a sample of global firms developing complex electro-mechanical products (e.g., automobile components, railway propulsion systems, and medical devices). Our grounded theory approach articulates an understanding of ASGM through extensive interviews of experienced professionals. Our thematic analysis supports many expected benefits …

Micromechanical Prediction Model Of Viscoelastic Properties For Asphalt Mastic Based On Morphologically Representative Pattern Approach, Zhichen Wang, Naisheng Guo, Xu Yang, Shuang Wang

Michigan Tech Publications, Part 1

This paper is devoted to the introduction of physicochemical, filler size, and distribution effect in micromechanical predictions of the overall viscoelastic properties of asphalt mastic. In order to account for the three effects, the morphologically representative pattern (MRP) approach was employed. The MRP model was improved due to the arduous practical use of equivalent modulus formula solution. Then, a homogeneous morphologically representative model (H-MRP) with the explicit solution was established based on the homogenization theory. Asphalt mastic is regarded as a composite material consisting of filler particles coated structural asphalt and free asphalt considering the physicochemical effect. An additional interphase …

Dynamic Dependency Collapsing, Görkem Aşılıoğlu

Dissertations, Master's Theses and Master's Reports

In this dissertation, we explore the concept of dynamic dependency collapsing. Performance increases in computer architecture are always introduced by exploiting additional parallelism when the clock speed is fixed. We show that further improvements are possible even when the available parallelism in programs are exhausted. This performance improvement is possible due to executing instructions in parallel that would ordinarily have been serialized. We call this concept dependency collapsing. We explore existing techniques that exploit parallelism and show which of them fall under the umbrella of dependency collapsing. We then introduce two dependency collapsing techniques of our own. The first technique …

Buckling Load Study On Pop Nut (Rivet) Using Finite Element Analysis, Saurabh Shankar Shegokar

Dissertations, Master's Theses and Master's Reports

This study highlights the material behavior in riveting operation that includes buckling load analysis using ABAQUS. Finite Element Analysis is used to find the buckling load vs. Displacement results and validated with the results obtained in physical testing of rivet (POP Nut). A mesh sensitivity study is performed using ABAQUS to understand the optimum mesh size for this analysis. An axisymmetric model with contact properties is created and simulated to reduce the simulation time using ABAQUS. The results obtained through Finite Element Analysis show a good resemblance with the testing results. Design changes were suggested to achieve better results that …

Estimation Of Atmospheric Conditions Over A Long Horizontal Path Using Multi-Frame Blind Deconvolution (Mfbd) Techniques In Comparison With Delayed Tilt Anisoplanatism (Delta) Software, Hannah Stoll

Dissertations, Master's Theses and Master's Reports

The potential to track and view objects in space from the ground with greater near real time knowledge of the intervening turbulence would be a revolutionary capability. The objective of this thesis is to cross-validate two separate methods used to estimate the Fried parameter. This verification is a step toward a commercial grade product that would make real-time estimates of the turbulence strength along an optical path from a ground-based observatory to a satellite in orbit around the Earth. Michigan Technological University has developed a multi-frame blind deconvolution (MFBD) algorithm used to estimate r0 and it was tested against MZA’s …

Radio Frequency Studies Of Soot Loading And Ammonia Storage On A Diesel Particulate Filter With A Scr Catalyst Coating, Shreyans Sethia

Dissertations, Master's Theses and Master's Reports

The radio frequency (RF) measurement technique has been shown to be a viable method for measurement of the amount of soot loaded onto DPF’s ^[1] and the amount of NH₃ stored on SCR catalysts ^[2]. In one of the configurations, a microwave resonant cavity is formed by the metal can encasing the enclosed catalyst. Two metal probes acting as antennas are placed on either side of the catalyst. Power transmitted between the antennas is monitored as the frequency of the signal is swept. At certain frequencies, resonance is achieved. Measurements of the resonance frequencies, amplitude at resonance, and …

Heterogeneous Uncertainty Quantification For Reliability-Based Design Optimization, Mingyang Li

Dissertations, Master's Theses and Master's Reports

Uncertainty is inherent to real-world engineering systems, and reliability analysis aims at quantitatively measuring the probability that engineering systems successfully perform the intended functionalities under various sources of uncertainties. In this dissertation, heterogeneous uncertainties including input variation, data uncertainty, simulation model uncertainty, and time-dependent uncertainty have been taken into account in reliability analysis and reliability-based design optimization (RBDO). The input variation inherently exists in practical engineering system and can be characterized by statistical modeling methods. Data uncertainty occurs when surrogate models are constructed to replace the simulations or experiments based on a set of training data, while simulation model uncertainty …