Engineering Commons^™

A Study Of The Structural Rearrangements Accompanying Room Temperature Recovery Of High Purity Aluminum, Carlos Manuel Lago

Masters Theses

"X-ray methods (Laue back reflection and transmission) and etch pit studies were used in order to follow structural changes in the deformed metallic lattice during room temperature recovery. The accumulative evidence indicates that the deformed lattice undergoes subboundary movements and regrouping of fragments within a few days after stressing. On the basis of a superficial investigation, it was found that fast neutron bombardment increases the rate of room temperature recovery. Through the use of a new etchant, a finer substructure was revealed within the Lacombe subgrain. Glide strain values were determined for the series investigated, and a new approach was …

Maximum Present Value Calculations With Digital Computers, James Boyd Robison

Masters Theses

"This paper discusses maximum present value calculations for a mineral property using digital computers. A semi-quantitative mathematical model to optimize operating conditions is considered. The model is based on a modified cash flow analysis. Many variables affect the solution, and their effect upon present value is described. Selected data (mining rate, costs, reserves, metal sales price, and others) for a hypothetical open pit copper mine are used in a set of solutions for present value. The results are discussed in detail. It is concluded that: (1) Digital computer methods are rapid and useful, (2) Changes in the mining rate, average …

Active Band-Pass Filters Using Twin-Tee Networks, Terry B. Watson

Masters Theses

"The primary objective of this thesis was the design and construction of a set of filters to determine the spectral energy density of random signal data in the spectrum from 10 cps to 20 kcps. The statement of the problem placed rather exacting conditions on the cost and performance of the equipment, and these conditions were met to the extent detailed in the following pages. A secondary objective was the investigation of techniques to improve the performance of band-pass active filters using resistive-capacitive feedback networks. This objective was not achieved to the author's satisfaction, although several promising ideas were discovered"--Abstract, …

A Study Of The Effect Of Surface Beveling On Silicon Rectifiers, Gary L. Voorhis

Masters Theses

"The problem in this thesis is to experimentally obtain voltage vs distance data for different angles of bevel, to determine the optimum bevel angle on the basis of minimum surface electric field, and also to determine the location of the maximum surface electric field with respect to the p-n junction. Experimental equipment is constructed and results are graphically illustrated. It is concluded that in general the maximum surface electric field decreased as the bevel angle decreased, that neglecting practical considerations the optimum bevel angle was 3⁰, and that the maximum surface electric field occurred near, but not at the p-n …

The Effect Of Epoxy Resins On The Plasticity Index Of An A-6 Soil, A. R. Van Steenbergen

Masters Theses

"This thesis reports the results of an investigation of the variation in plasticity of a clayey soil after treatment with small quantities of epoxy resin and curing agent or with curing agent alone. The series of samples tested consisted of an A-6 soil obtained from the vicinity of Rolla, Missouri, combined with: 1. 0-3% of triethylenetetramine hereafter referred to as TETA. 2. 0-3% of diethylenetriamine hereafter referred to as DETA. 3. 0-3% of Araldite 6010 resin cured with TETA. The TETA content was varied form 20% to 100% of the resin by weight. 4. 0-3% Araldite 6010 resin cured with …

Analysis Of Continuous Folded Plate Roofs, Yung-Ping Wang

Masters Theses

"This work presents an analysis of continuous folded plate roofs considering the effects of relative joint displacements. For this analysis the normal modes of the lateral beam vibration were used as the form of the deflection curve and the loading was sinusoidal. By using symmetry and anti-symmetry, a possible method of analyzing prismatic folded plate roofs comprising one bay transversely but continuous over two or more spans longitudinally is suggested"--Abstract, page ii.

Measurement Of Stray Load Loss Of D.C. Machines, Kanaiyalal Ramanlal Shah

Masters Theses

"For many years the standard practice, in calculation of conventional efficiency of d.c. machines, has been to include stray load losses as equal to 1% of the output. This assumption may be true for large, compensated d.c. machines but it is known to be small for smaller, uncompensated, general-purpose, industrial-type machines of open design. An A.I.E.E. Committee on Rotating Machines was formed to investigate whether the present practice of assigning 1% for the stray load loss is justified or not. They reached a conclusion, reported in 1949, after investigating 243 stray loss tests on different motors ranging from 1/2 hp …

Analysis Of The Flow Characteristics Through A Water Pressure Regulator, Anthony Lee Jatcko

Masters Theses

"This thesis presents an analysis of the flow characteristics through a water pressure regulator. Characteristic curves of the relationship between pressure drop through the regulator and flow through the regulator are developed. To further analyze these relationships, a least squares computer analysis was used to develop equations to fit these curves. An investigation into the modes of dissipating pressure energy in this type of regulator tends to indicate that a significant portion of the energy is lost through viscous shearing action in the area of high turbulence. The aforementioned characteristic curves also showed definite critical pressure points in the form …

Application Of The Photoelastic Coating Method To Evaluate The Stress Distribution On The External Surface Of The Cap Of An Electrical Insulator, Harijeetsinh Jagtiani

Masters Theses

"The Photoelastic Coating Method was applied to find the surface stresses on the cap of an electrical insulator. The strain distribution was observed and photographed. This color photograph indicated a visible geography of the maximum shear strain distribution in the region of the insulator where the birefringent plastic was bonded with a reflective cement. The Oblique Incidence technique was used to determine the principal stresses from the maximum shear strain (or the principal strain difference) readings, obtained from Normal Incidence. The critical cross-section of the insulator head was optically located, giving an initiative for the re-design of the insulator cap. …

Thermal Degradation Of Poly (Methyl Methacrylate) In Solutions In A Closed System, Vikram Pranjivandas Parikh

Masters Theses

"A study has been made of the thermal degradation of poly (methyl methacrylate) of two different molecular weights, 2,303,000 and 43,000, in 1,2-dichloroethane in a closed system. The results indicated that the polymer having a molecular weight of 2,303,000 undergoes degradation while the low molecular weight polymer 43,000 undergoes reverse polymerization, and the molecular weight remains constant. The molecular weight of high molecular weight samples after 48 hours decreased from 2,303,000 to 2,232,000 and 1,690,400 at 50⁰C and at 98.5⁰C, respectively"--Abstract, page [i].

The Electrochemical Oxidation Of Crotonic Acid, John L. Cannaday

Masters Theses

"The purpose of this investigation was to explain the mechanism of the electrochemical oxidation of crotonic acid on platinized-platinum anodes at 80⁰C.

A current-potential study was conducted using the parameters of pH and crotonic acid concentration. Faradaic efficiency was determined by measurement of CO₂ production.

Oxidation occurred both in acidic and basic solutions.The Faradaic efficiency was approximately 100 per cent.

The results were interpreted in terms of a mechanism having the following characteristics.

(a) The first charge transfer is the rate determining step.

(b) The rate is the sum of the rates for two parallel reactions. In strongly acidic solutions, …

A Study Of The Non-Newtonian Turbulent Fluid Flow Through An Annulus, Yogesh R. Parikh

Masters Theses

"This investigation is concerned with the study of non-Newtonian flow through an annulus. The experimental analysis of incompressible non-Newtonian fluids in a long cylindrical annulus of radius ratio 0.375 was studied in the turbulent region. Different types of non-Newtonian fluids were used to procure flow behaviour for the annulus.
The effect of increasing flow rate of the non-Newtonian fluids was evaluated by gathering pressure drop data across the annulus using a differential manometer. The power-law model is used in this study to characterize the non-Newtonian flow. The parameters of the power-law model were evaluated by gathering viscometric data on a …

Optimization Of Flywheel Design For Internal Combustion Engines, Dady Jal Patel

Masters Theses

"A new approach to the problem of flywheel design has been developed, thus eliminating some of the problems of conventional design. The term flywheel design, in this thesis, refers to the determination of the flywheel inertia (mass moment of inertia) only. Two versatile computer programs were set up to obtain the flywheel inertia and the turning moment diagram for a large variety of internal combustion engines, and use was made of these programs to optimize the inertia of the flywheel with respect to speed. As an illustration the data of a 1960 Corvair engine were selected, and the results obtained …

Analysis Of Flat Slabs With Various Edge Supports, Wu-Mo Chern

Masters Theses

"This study presents the solution of flat slabs with various edge conditions including T-Beam edge supports, The equations formulated are based on the finite difference method and solved using an electronic computer.

The results indicate that the solution of these slabs by the finite difference approximation is a practical method. In addition, this method is more flexible and yields moment values that are considerably more accurate than those obtained using the ACI Code"--Abstract, page ii.

The Transmission Of Loads To Point Bearing Piles In Sand Beneath Retaining Walls, Alan Albert Kamp

Masters Theses

"An experimental investigation was made of the way in which loads were transmitted to point bearing H-piles in sand under a retaining wall. Using a plastic model, the moments and axial loads were determined along the length of the pile by measuring the strains with electric strain gages. A comparison was made of the experimental results at the top of the pile and the analytical results at this point; the latter obtained from the common practice used in design. The comparison was very poor because the excessive horizontal load (that part of the horizontal load which could not be carried …

The Dielectric Properties Of A Synthetic Fluor-Mica Formed By Glass-Ceramic Fabrication Techniques, Ray Fred Schumacher

Masters Theses

"A tetrasilicic fluor-mica, K₂Mg₅Si₈O₂₀F₄, was synthesized, utilizing glass forming techniques and subsequent heat treating of the mica glass. Discs, approximately two inches in diameter, were formed and heat-treated at selected temperatures between 700⁰C. and 1150⁰C. for various time periods. Density change, weight loss, shrinkage, and dielectric properties were measured to determine the characteristics of this material"--Abstract, page ii.

Analog Simulation Of A Synchronous Machine, J. Derald Morgan

Masters Theses

"The problem presented here is a study by an analog computer simulation of a synchronous machine under balanced three phase, short-circuit conditions. The purpose is to obtain a solution that is more accurate than one obtained by approximate methods using transient and subtransient reactances as is often done. This simulation is accomplished by using an idealized synchronous machine. The equations relating voltage and currents in the machine, as well as speed and torque, are presented for simulation. The equations for the machine include the saliency of one member, as well as the effect of speed and the damper windings. A …

A Feedback Compensator Design For Linear Control Systems, Thsai-Ten Lin

Masters Theses

"The compensation process in control system engineering is indispensable. The addition of a compensator to a fixed plant can often make the system meet certain specifications easily. In this study an attempt was made to use a general purpose digital computer to design a feedback compensator. The method developed is first to determine the minimum gain of the amplifier and the number of compensator poles and zeros based on the given specifications. then free hand root-loci are plotted, with several combinations of possible compensation variables. These data are used as the open-loop transfer function from which the poles and zeros …

Evaluation Of Pile Bearing Capacity By Use Of The Wave Equation, Stuart H. Williams

Masters Theses

"The wave equation method of evaluating pile bearing capacity is investigated by using data obtained from a comprehensive pile testing program. Modifications which create a more accurate and realistic approach are made to the method proposed by previous investigators. With the use of these modifications, correlation between observed and computed results is more readily obtained. Selected pile formulas in the empirical, static, and dynamic categories are reviewed so that a direct comparison between these and the wave equation method can be made"--Abstract, page ii.

An Evaluation Of The Feasibility Of Neutron Microradiography, Maynard L. Arment

Masters Theses

"The metal working industry has used metallography and microradiography extensively in the past decade. X-ray or gamma microradiography has several advantages as compared to metallography, but a disadvantage concerning alloys of adjacent elements; microradiography cannot distinguish between elements 2 or less atomic numbers apart. Attempts were made using neutron microradiography to distinguish between cadmium and tin rich grains. A maximum resolution of 0.017 inches was found with a calculated possibility of a resolution less than 0.002 inches"--Abstract, page ii.

Study Of Deformation Of Non-Oscillating Droplets In Liquid Media, Arun Kumar Agrawal

Masters Theses

"The object of this investigation was to find a method for predicting the deformation of non-oscillating liquid droplets which are moving in liquid media, from a knowledge of droplet size and the physical properties of the continuous and dispersed phase systems. The deformation of thirteen liquid-liquid systems was experimentally studied in this investigation"--Abstract, page i.

A Feasibility Study Of The Haeffner Effect In Mercury, Paul Martin Machmeier

Masters Theses

"An investigation of the Haeffner Effect in mercury by the use of a decade scaler suggested the need for a comprehensive statistical analysis of the data to justify reporting the presence of an isotopic separation. It has also been shown that the temperature of the mercury column must be accurately calculated before a temperature dependent relationship with the Haeffner Effect can be cited"--Abstract, page ii.

A Study Of Radiation Heat Transfer In Rectangular Ducts And Enclosures, Jenn-Wuu Ou

Masters Theses

"The purpose of this study is to determine the radiant heat transfer in rectangular configurations and construct a general computer program. Two specific cases are studied in this work. The first case is a rectangular duct with openings at each end. The duct is separated into two sections which are called the source and the sink respectively. A linear temperature profile is imposed on the source section. The energy loss of both the source and the sink is investigated. The second case is a complete rectangular enclosure. The two end plates are called the source and the sink respectively. A …

Order-Disorder In Fe₃Al At Various Temperatures Induced By Neutron Irradiation, Robert F. Toma Jr.

Masters Theses

"Resistivity measurements were made on ordered and disordered Fe₃Al samples while irradiated by neutrons.

In the ordered as well as the disorder state, the different Fe₃Al samples were heated to 100, 150, 200, 250, and 300°C respectively, and were irradiated by a fast neutron flux of 0.534 x 10¹⁰ neutrons/cm²-sec. The ordered Fe₃Al measurements were characterized by an increase in resistivity denoting an advancement toward disorder. The disordered Fe₃Al measurements were characterized by a decrease in resistivity denoting an advancement toward order. In the Fe₃Al ordered and disordered samples …

Circular Polarization From A Corner Reflector Antenna With Tilted Dipole Of Arbitrary Length, Ruben A. Carrizo M.

Masters Theses

"The problem consists of the development of the electric far field equations for a forty-five degree corner reflector antenna with a tilted dipole, of arbitrary length, centered at the corner bisector plane to produce circularly-polarized radiation. The far field expression was developed as a function of the spherical coordinate system variables and placed in Fortran language in order to determine the dipole locations which would produce circularly-polarized radiation. At such dipole locations the field patterns were plotted in the [theta] = [pi]/2 and [phi] = 0.0 planes. Computations were made by the IBM 1620 digital computer"--Abstract, page ii.

Performance Of A Reciprocating Packed Extraction Column, Thomas Vardaman Konkle

Masters Theses

"The performance of a mechanically-aided liquid extraction column was investigated utilizing the methyl isobutyl ketone-acetic acid-water ternary extraction system. Mechanical power was added to the extraction system by reciprocating a wire-mesh packing of high void volume at various frequencies and displacements. The effects of total throughput on performance were studied in increments of 5,000 pounds per hour per square foot up to the onset of flooding, and the column performance was evaluated as a function of power addition to the extraction system. In comparing the various types of mechanically-aided extraction columns, it was determined that the throughputs achieved with the …

Piezometric Levels And Shallow Aquifers, Dillon And Meramec Spring Quadrangles, Missouri, James Hugh Crouch

Masters Theses

"Little is known about groundwater in carbonate rock; quantitative data about limestone and dolomite aquifers are almost non-existent. Objectives of this study are: identification of shallow aquifers, and yield, occurrence, and piezometric level of groundwater in cherty dolomitic rocks in eastern Phelps County, Missouri. Area studied comprises of the 7.5-minute Dillon and Meramec Spring Quadrangles. The data used were derived from water well logs, interviews with well drillers and owners, and a previously available geologic map.

The Jefferson City, Roubidoux, and Gasconade formations are aquifers. Groundwater in the Jefferson City formation is perched. West and north of Dry Fork creek, …

Temperature Distribution In Thermal Boundary Layers (In Free Convection) Using A Modified Schlieren Method, Philip Ling Chen

Masters Theses

"A simple optical apparatus, the Schlieren interferometer, was constructed for the quantitative investigation of free convection heat transfer from solid bodies. The photographic results, checked by using thermocouples, were used in evaluating the temperature distribution, the key to the solution of these problems. Interpretation of the photographic results was made using the simple calculation for the conventional interferogram and the Dale-Gladstone law. Although the experiments were limited to a heated flat plate and a heated wire, two dimensional test pieces of irregular configuration can be investigated by the same apparatus with simple modifications. The photographs of the conventional Schlieren, the …

A Study Of The Influence Of Shock Waves On The Stability Of Rock-Bolt Anchorage, Helmut W. Habenicht

Masters Theses

"An experimental method was developed to compare strain data for rock and rock bolts when exposed to shock waves released by blasting. During a 32-day period of experimentation, one rock sensor and four rock-bolt sensors were observed simultaneously. By their placement in the side wall of a structurally stable drift, secondary static stresses were excluded. Bolt gage responses, then, could be considered to originate only from a decay of anchorage stability during static conditions or as a reaction to the vibrations. Interpretation of test results indicated a distinct loss in bolt-strain during vibrations, accompanied by a smaller but steady loss …

Optimum Finite Memory Nonlinear Filter, Ching-Chyoun Yang

Masters Theses

"This thesis investigates the possibility of using the Zadah theory and a machine type computer to design an optimum finite memory nonlinear filter for extraction of Poisson distributed signal pulses from a background of Gaussian noise. Basically the procedure involves the technique of solving simultaneous equations by the computer. We demonstrate that it is possible to find the limitation of the filter of class N₁ in terms of an absolute minimum mean square error. However, due to the capacity of the computer we do not actually determine the absolute minimum. Nevertheless we do show that the mean square error decreases …