Engineering Commons^™

Influence Of Growth Parameters On The Synthesis Of Mos2 Films, Victor Okonkwo

Honors Undergraduate Theses

Information processing is crucial in modern society, placing a great emphasis on the performance of optoelectronic devices to match ever increasing processing and memory needs. Within these devices, MoS₂ has demonstrated great potential as transistors due to its enhanced electrostatic control. As increased layer thickness of quality MoS₂ films have been shown to boost the performance of its transistors, growth parameters for the synthesis of ideally uniform and large area multilayered films via chemical vapor deposition were investigated. By increasing the flow pressure in the system and the growth time, increasing levels of thickness and nucleation density was …

Engineering The Electrode Properties For Developing High Performance Supercapacitors, Kowsik Sambath Kumar

Electronic Theses and Dissertations, 2020-2023

Rising global warming concern demands the need for a rapid transition to renewable energy sources. The intermittent nature of these sources emphasizes the requirement of developing highly efficient electrochemical energy storage devices like supercapacitors and batteries. Supercapacitors are at the forefront of powering various devices spanning from electric cars to aircraft. Here, we have engineered the electrode material properties for developing supercapacitors with high capacitance, energy density and cycle life. Among the electrode materials, we have focused on improving the energy storage performance of 2D materials like graphene oxide (GO) and tungsten disulfide (WS2), in addition to metal oxides such …

Processing-Microstructure-Property Correlation For 316l Stainless Steel Manufactured By Laser Powder Bed Fusion, Nathalia Diaz Vallejo

Electronic Theses and Dissertations, 2020-2023

The microstructural development of 316L stainless steel (316L SS) was investigated over a wide range of systematically varied laser powder bed fusion (LPBF) parameters, such as laser power, laser scan speed, hatch distance, and volumetric energy density. The use of volumetric energy density between 46 and 127 J/mm3 produced samples with relative density above 99.8% demonstrating that even in the optimized range of processing parameters the pores are unavoidable. Shifting from this range through a variation of laser scan speed produced two types of flaws, lack of fusion (LoF) and keyhole (KH) porosity leading to a decrease in the relative …

Effect Of The Extended Rigid Flapping Trailing Edge Fringe On An S833 Airfoil, Hongtao Yu, Zifeng Yang

Mechanical and Materials Engineering Faculty Publications

A 2D numerical simulation was conducted to investigate the effect of an extended rigid trailing edge fringe with a flapping motion on the S833 airfoil and its wake flow field, as an analogy of an owl’s wing. This study aims to characterize the influence of the extended flapping fringe on the aerodynamic performance and the wake flow characteristics downstream of the airfoil. The length (Le) and flapping frequencies (fe) of the fringe are the key parameters that dominate the impact on the airfoil and the flow field, given that the oscillation angular amplitude is fixed at 5◦. The simulation results …

From Field To Failure: Detecting And Understanding Reliability Defects In Crystalline Silicon Photovoltaics, Dylan Colvin

Electronic Theses and Dissertations, 2020-2023

Severe pollution levels and the growing influence of climate change have shown that dirty energy sources need renewable and sustainable replacements. The field of photovoltaics (PV) has grown substantially over the years from a niche space solar market to a commodity in large part due to improvements in reliability. Reliability of all materials in a PV module must be considered. The industry has seen an explosion of innovation in cell interconnection technologies with significant market penetration in the past several years. These emerging, less mature technologies require more reliability information to guide improvements. Degradation studies of long-term outdoor exposure and …

Additive Manufacturing Of Continuous Carbon Fiber-Reinforced Sic Ceramic Composite With Multiple Fiber Bundles By An Extrusion-Based Technique, Ruoyu Chen, Adam Bratten, Joshua Rittenhouse, Ming-Chuan Leu, Haiming Wen

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Due to the high cost, complex preparation process and difficulty in structural design, the traditional methods for carbon fiber reinforced SiC ceramic composite preparation have great limitations. This paper presents a technique for the additive manufacturing multiple continuous carbon fiber bundle-reinforced SiC ceramic composite with core-shell structure using an extrusion-based technique. A conventional nozzle system was modified to print simultaneously a water based SiC paste with continuous carbon fibers. Different levels of binder contents were investigated to optimize the stickiness, viscosity, thixotropy and viscoelasticity of the paste. After sintering, SiC whiskers were generated on the surface of fiber, which is …

Stimuli-Responsive Chitosan-Based Hydrogels For Antibiotic Delivery, Tu Tran Vo Minh

Chulalongkorn University Theses and Dissertations (Chula ETD)

This study aims to investigate hydrogels fabricated via green approaches for drug delivery application. Biocompatible polymer-based drug delivery systems (DDS) have gained popularity in recent years because of their ability to improve the efficacy and safety of drug delivery by providing targeted and sustained release of drugs to reduce the frequency of dosing, making it more convenient for patients. Chitosan is one of the polymers commonly used for this purpose due to their higher water retention and porosity, which create space for loading medicine into the matrix. However, the potential utilization of endogenous and exogenous stimuli controlling drug release still …

การเตรียมและการวิเคราะห์ลักษณะสมบัติผ้าไหมที่เคลือบผิวด้วยไคโตซาน/ซิลเวอร์/มอนต์มอริลโลไนต์คอมโพสิต, ลักษณารีย์ มาละ

Chulalongkorn University Theses and Dissertations (Chula ETD)

งานวิจัยนี้ศึกษาการเคลือบผิวผ้าไหมด้วยไคโตซาน/ซิลเวอร์/มอนต์มอริลโลไนต์คอมโพสิต โดยซิลเวอร์คอลลอยด์ถูกสังเคราะห์ด้วยกระบวนการรีดักชันทางเคมี และกระบวนการรีดักชันด้วยแสงยูวี ผลการศึกษาพบว่าภาวะที่เหมาะสมสำหรับการเคลือบซิลเวอร์คอลลอยด์สีน้ำเงินที่เตรียมด้วยวิธีรีดักชันทางเคมี โดยใช้โซเดียมโบโรไฮไดรด์ (NaBH4) เป็นตัวรีดิวซ์ (ความเข้มข้นของซิลเวอร์ไนเตรต 0.2 มิลลิโมลาร์) บนผ้าไหมอย่างสมบูรณ์ด้วยกระบวนการจุ่มแช่และกวน โดยใช้อัตราส่วนโดยน้ำหนักของซิลเวอร์คอลลอยด์ : น้ำหนักผ้าไหม เท่ากับ 1 : 200 คือ ที่อุณหภูมิในการเคลือบ 100 องศาเซลเซียส เป็นเวลา 90 นาที โดยซิลเวอร์คอลลอยด์ถูกปรับค่าความเป็นกรด-ด่าง เท่ากับ 5 ด้วยกรดแอซิติก ซึ่งผ้าไหมที่ถูกเคลือบด้วยซิลเวอร์คอลลอยด์และไคโตซานแสดงสมบัติการต้านแบคทีเรียชนิด S. aureous ได้ดีเยี่ยม และเมื่อนำไปเคลือบทับด้วยมอนต์มอริลโลไนต์ด้วยกระบวนการบีบอัดโดยใช้เครื่องบีบอัด พบว่าช่วยเพิ่มสมบัติการหน่วงไฟให้กับผ้าไหม แต่สมบัติการต้านแบคทีเรียลดลง การสังเคราะห์ซิลเวอร์คอลลอยด์โดยวิธีรีดักชันด้วยแสงยูวี โดยการฉายแสงยูวีบนสารละลายซิลเวอร์ไนเตรตที่เตรียมร่วมกับไคโตซาน พบว่าที่เวลา 2 ชั่วโมง เป็นเวลาที่เหมาะสมที่สุดในการเตรียม ซึ่งแสดงสเปกตรัมการดูดกลืนแสงที่แสดงสมบัติ Localized surface plasmon resonance (LSPR) บ่งชี้การเกิดอนุภาคซิลเวอร์นาโนหลังการฉายแสงยูวี และเมื่อนำไปวิเคราะห์โครงสร้างจุลภาค พบการกระจายของอนุภาคซิลเวอร์นาโนบนพื้นผิวของผ้าไหม หลังจากนั้นนำไปเตรียมเป็นคอมโพสิตร่วมกับมอนต์มอริลโลไนต์ และเคลือบบนผ้าไหมด้วยกระบวนการบีบอัดโดยใช้เครื่องบีบอัด พบว่าผ้าไหมที่ผ่านการเคลือบด้วยไคโตซาน/ซิลเวอร์ และไคโตซาน/ ซิลเวอร์/มอนต์มอริลโลไนต์คอมโพสิต ด้วยการรีดิวซ์ด้วยแสงยูวี ให้ผลการทดสอบสมบัติการต้านแบคทีเรียและการหน่วงไฟในทำนองเดียวกันกับวิธีรีดักชันทางเคมี

Rational Design Of Flexible And Stretchable Electronics Based On 3d Printing, Yuanhang Yang

Theses and Dissertations

Flexible and stretchable electronics have been considered as the key component for the next generation of flexible devices. There are many approaches to prepare the devices, such as dip coating, spin coating, Mayer bar coating, filtration and transfer, and printing, etc. The effectiveness of these methods has been proven, but some drawbacks cannot be ignored, such as lacking pattern control, labor consuming, requiring complex pretreatment, wasting conductive materials, etc.

In this investigation, we propose to adopt 3D printing technology to design flexible and stretchable electronics. The objective is to rationally design flexible and stretchable sensors, simplify the preparation process, form …

Nanomechanical Characterization And Comparison Of Additively Manufactured Grcop-42 Alloy, Trupti Suresh Mali

Electronic Theses and Dissertations

In an aggressive thermomechanical environment, the superior mechanical as well as thermal properties of materials play an essential role. GRCop which is a copper-based alloy developed by NASA has the potential to fulfill the requirements necessary for hightemperature applications such as the combustion chamber of liquid rocket engines. The first alloy of this family, GRCop-84 (Cu-8 wt.% Cr-4 wt.% Nb) was discovered followed with the development of GRCop-42 (Cu-4 wt.% Cr, 2 wt.% Nb). The reduction in alloying element percentage enhanced thermal conductivity with less built time while maintaining the strength of the material. The conventional fabrication is replaced with …

Moisture Content Prediction In Polymer Composites Using Machine Learning Techniques, Partha Pratim Das, Monjur Morshed Rabby, Vamsee Vadlamudi, Rassel Raihan

Institute of Predictive Performance Methodologies (IPPM-UTARI)-Archive

The principal objective of this study is to employ non-destructive broadband dielectric spectroscopy/impedance spectroscopy and machine learning techniques to estimate the moisture content in FRP composites under hygrothermal aging. Here, classification and regression machine learning models that can accurately predict the current moisture saturation state are developed using the frequency domain dielectric response of the composite, in conjunction with the time domain hygrothermal aging effect. First, to categorize the composites based on the present state of the absorbed moisture supervised classification learning models (i.e., quadratic discriminant analysis (QDA), support vector machine (SVM), and artificial neural network-based multilayer perceptron (MLP) classifier) …

Evaluation Of Static Recrystallization And Grain Growth Kinetics Of Hot-Rolled Az31 Alloy, Salaheddine Sadi, Abdelkader Hanna, Thierr Baudin, Anne-Laure Helbert, François Brisset, Djamel Bradai, Hiba Azzeddine

Journal of Metals, Materials and Minerals

The static recrystallization/grain growth kinetics of the AZ31 (Mg-3Al-1Zn, wt%) alloy were investigated employing Vickers microhardness and electron backscatter diffraction (EBSD) measurements. The AZ31 alloy was subject to a hot-rolling for 70% of thickness reduction and then annealed at various temperatures (150°C, 250°C, and 350°C) from 5 min to 24 h. First, the static recrystallization kinetics were analysed by means of the Johnson-Mehl-Avrami-Kolmogorov (JMAK) model. The results showed that the recrystallization occurred under two regimes both involving their own Avrami exponent/ activation energy. In regime I, the Avrami exponent was found in the range of 1.5-0.35 depending on the annealing …

Effect Of Al Addition On Crystal Structure Of Algan/Gan On Gaas (001) Substrate Grown By Metalorganic Vapor Phase Epitaxy, Nattamon Suwannaharn, Sakuntam Sanorpim, Suphakan Kijamnajsuk, Visittapong Yordsri, Noppadon Nuntawong, Kentaro Onabe

Journal of Metals, Materials and Minerals

Effects of Al addition on a structural phase modification in AlGaN/GaN films on GaAs  substrate grown by MOVPE have been investigated. To examine the effect of Al addition, AlGaN/GaN films were grown with varied a molar flow ratio of TMAl to the total group-III elements of 0, 0.15, and 0.30. Quantity of hexagonal phase incorporation was evaluated by the ratios of integrated XRD intensity of hexagonal  plane to cubic  plane from reciprocal space mappings. The diffraction geometry factor was considered in the calculation. The results suggest that GaN primarily contains a hexagonal phase with a small fraction of a cubic …

Facile Synthesis Of Heterostructured G-C3n4/Ag -Tio2 Photocatalysts With Enhanced Visible-Light Photocatalytic Performance, Chonnipha Tangwongputti, Prasert Reubroycharoen, Pornapa Sujaridworakun

Journal of Metals, Materials and Minerals

In this study, the g-C3N4/Ag-TiO2 composite photocatalysts were prepared to enhance the efficient utilization of solar energy. The g-C3N4 was synthesized by facile heat treatment of urea at 600℃ for 4 h, and 0.05 wt% to 3 wt% Ag-TiO2 were obtained through the chemical reduction method. The composite photocatalysts were prepared by mixing the g-C3N4 and Ag-TiO2 with a weight ratio of 50:50 at room temperature. The photocatalytic efficiency was carried out by using 0.05 g of photocatalysts with 10 mg·L-1 of rhodamine B 120 mL under 60 min of visible light irradiation. The experimental results indicated that a sample …

Effect Of Pre-Carbonization Temperature On The Porous Structure And Electrochemical Properties Of Activated Carbon Fibers Derived From Kapok For Supercapacitor Applications, Nu Myat Thazin, Nattapat Chaiammart, Myo Myo Thu, Gasidit Panomsuwan

Journal of Metals, Materials and Minerals

Activated carbon fibers (ACFs) were successfully synthesized from kapok via a two-step process: (i) pre-carbonization and (ii) chemical activation. The pre-carbonization temperature was varied at 300℃, 400℃, and 500℃. The mixing ratio of the pre-carbonized product and potassium hydroxide (KOH) was 3:1, while the activation temperature was 800℃. The effect of pre-carbonization temperature on the morphology, surface area and porosity, chemical functional group, and phase structure of ACFs was investigated and discussed. The characterization results showed that ACFs exhibited an amorphous carbon structure with a hollow fiber shape resembling the kapok. The specific surface area decreased from 487 m2×g-1 to …

Effects Of Milling Time On Sintering Properties And Formation Of Interface Al4c3 On Graphite Reinforced Al-4.5cu-1.5mg Nanocomposite, Angga Khairul Fahmi, Haris Rudianto, Agus Sukarto Wismogroho, Wahyu Bambang Widayatno, Didik Aryanto, Bambang Hermanto

Journal of Metals, Materials and Minerals

Aluminum-based metal matrix nanocomposites have been extensively researched and developed for aerospace and automotive applications. Al-4.5Cu-1.5Mg with 0.5 wt% graphite were milled for 2 h, 4 h, 6 h, and 8 h using shaker mill under argon gas. The phenomena of deformation, fracturing, and cold welding during shaker mill were investigated to observe how the shaker mill effects on their morphology and formation of intermetallic phases due to its very high speed. Sintering under ultra-high purity argon gas for 99.9999% was done to produce high density materials. Intermetallic phase Al4C3 was found as a result reaction between aluminum and graphite …

Influence Of Six-Step Heat Treatment On Microstructures And Mechanical Properties Of 5160 Alloy Steel, Pattama Apichai

Journal of Metals, Materials and Minerals

AISI 5160 alloy steel grade with complete martensite structure to get the high-strength steel sheets quenched at 900 (Q1), 870 (Q2), 840 (Q3) and 810°C (Q4), respectively and temped at 780°C (Q5) and 680°C (Q6), respectively. The results show ferrite and pearlite microstructural appeared in as-sheet conditions. The strengthening rarely increased with increasing heat treatment steps, while the percentage elongation gradually decreased. The hardness change was secure with that of strengthening for the quenched martensite. In contrast, differences between the initial martensite hardness were no noticeable changes. The Q4 hardening involved the peak hardness and maximum ultimate tensile strength due …

Biodiesel Production From Waste Cooking Oil Using A New Heterogeneous Catalyst Sro Doped Cao Nanoparticles, Apisit Prokaewa, Siwaporn Meejoo Smith, Apanee Luengnaruemitchai, Mathi Kandiah, Supakorn Boonyuen

Journal of Metals, Materials and Minerals

Biodiesel production from waste palm cooking oil (WPCO) was studied. Calcium oxide with a strontium ion additive (Sr-CaO) was employed as a catalyst in transesterification reaction of used palm oil with methanol. The Sr-CaO was synthesized by co-precipitation method between SrCl2 and Ca(NO3)2, then calcined at 900°C for 5 h. The catalyst was characterized by using thermo-gravimetric analysis (TGA), X-ray diffraction (XRD), Scanning electron microscope (SEM), and Fourier transform infrared spectrometer (FT-IR). The morphology and elements content of Sr and Ca in the catalyst were confirmed by SEM-EDX. The approximate catalyst diameter is 12.6±5.9 µm. The highest conversion was 99.33% …

Study Of The Effect Of Ph, Conditioning And Flotation Time On The Flotation Efficiency Of Phosphate Ores By A Soybean Oil Collector, Zohra Farid, Mohamed Abdennouri, Noureddine Barka, Youness Jannani, M'Hamed Sadiq

Journal of Metals, Materials and Minerals

The mid-low grade of phosphate ore, rich by the silicate and carbonate gangue minerals needs a special treatment using the flotation process. Where the collectors play a pivotal role. This study was conducted to enrich an untreated phosphate ore (without washing, desliming, hydrocycling, etc.), with an eco-friendly and economic collector based on soybean oil. Different analytical techniques such as UV-Visible, ATR-FTIR spectrometric and XRD were used in order to analyse and characterize the flotation products. The effects of the parameters, pulp pH, conditioning time and flotation time on gangue removal efficiency by flotation, were investigated. Flotation tests were applied for …

The Finished Polyester Fabric With Hot Nh4oh Pretreatment And Mixed Zno-Zn(Oh)2 Nanoparticles For Hydrophobic Property, Samroeng Narakaew, Sittipong Au-Pree, Wipanoot Baison, Siwat Thungprasert, Itsariya Wattalo, Pranpreeya Jaipor, Theeraporn Promanan, Sukee Sukdee, Pakorn Santakij, Chainet Chanogkun, Kanjana Ruttanateerawichien, Aphiruk Chaisena, Pattama Apichai, Phiphop Narakaew

Journal of Metals, Materials and Minerals

This work aims to modify the hydrophobic coated polyester fabrics using 2%w/v ammonium hydroxide (NH4OH) at 90℃ prior and subsequently dipped in two difference aqueous zinc solution batchs containing 0.6%w/v zinc precursors with/without starch and NH4OH, finally dehydration, and characterized by the attenuated total reflection - Fourier transform Infrared (ATR-FTIR) and Raman spectroscopy (Raman), X-ray diffraction (XRD), Field emission scanning electron microscope (FE-SEM), Energy dipersive spectrometry (EDX), and Water contact angle (WCA) of 10 mL dropping at 23℃ and humidity of 63%. Raman spectra and XRD patterns results showed e-zinc hydroxide (e-Zn(OH)2), zinc oxide nanoparticle (ZnO NP) and ZnO-starch nanocomposite …

Epoxidized Natural Rubber/Silane Modified Silica Nanocomposites Prepared In Latex Stage, Supat Moolsin, Duangkamon Sawangkan

Journal of Metals, Materials and Minerals

Epoxidized natural rubber (ENR) was synthesized from natural rubber (NR) latex via in situ epoxidation using HCOOH and H2O2. The prepared ENR with 22 mol% epoxidation (ENR-22) was reinforced with silane modified silica (SMS) nanoparticles with different SMS loading in latex stage. The tensile properties, thermal stability, oil resistance and morphology of the ENR-22/SMS nanocomposites were investigated. The tensile strength was improved significantly and gained the maximum point at 7.5 phr SMS content. The thermogravimetric analysis showed an increased initial degradation temperature with the addition of SMS, suggesting higher thermal stability of the nanocomposites. The oil resistance of ENR-22/SMS nanocomposites …

Use Of Oil Palm Frond Waste To Reinforce Poly(Lactic Acid) Based Composites With The Improvement Of Interfacial Adhesion By Alkali Treatment, Nattakarn Hongsriphan, Jidapa Subsanga, Pimpisa Suebsai, Sunisa Sitthipong, Pajaera Patanathabutr

Journal of Metals, Materials and Minerals

Oil palm frond waste was used as reinforcing fibers for biodegradable poly(lactic acid) or PLA in order to produce green composites that increased the value of agricultural waste. The alkali-treated oil palm frond (OPF) fibers of 30 wt% or 40 wt% were compounded with PLA and moulded into specimens. The alkali treatment was 0 wt%, 1 wt%, 3 wt%, and 5 wt% of the fibers for compatibility improvement with PLA matrix. It was found that the alkali-treated PLA/OPF composites adding 30 wt% and 40 wt% had the flexural modulus to be about 55% and 75% higher than those without the …

Design, Development And Characterization Of A Mid-Frequency (35 Khz) Tonpilz Transducer Array From 0.675pmn-0.325pt Piezoceramics, Merve Nur Çiftçi, Berk Değirmenci, Irem Böbrek, Sedat Alkoy, Aykut Aykaç, Muhammet Boz, Ayşe Berksoy-Yavuz, Ezgi Yalcin, Namik K. Gozuacik, Ebru Menşur

Journal of Metals, Materials and Minerals

A mid-frequency tonpilz transducer array was designed and analyzed by finite element method using commercial ATILA code and constructed using piezoceramic rings with lead magnesium niobate (PMN)-lead titanate (PT) composition. The morphotropic phase boundary (MPB) 0.675Pb(Mg1/3Nb2/3)O3-0.325PbTiO3 composition was chosen to obtain higher performance from the transducer due to the superior dielectric and electromechanical properties of the MPB compositions. A pure perovskite phase was obtained from the ceramics. Piezoelectric charge coefficient (d33) was measured as 435 pC×N-1. Single tonpilz element and an array consisting of 7-unit array were constructed and later potted in polyurethane for underwater measurements. A second array was …

Amino-Containing Polymer-Coated Magnetite Nanoparticles As Nano-Adsorbents For Bisphenol A: Synthesis, Kinetic And Thermodynamic Study, Jakkrit Tummachote, Metha Rutnakornpituk, Duangdao Channei, Filip Kielar, Boonjira Rutnakornpituk

Journal of Metals, Materials and Minerals

Magnetite nanoparticles coated with poly(dimethyl aminoethyl methacrylate) (PDMAEMA@MNPs) and their quarternized form (PQDMAEMA@MNPs) were successfully synthesized and used as nano-adsorbents for bisphenol A (BPA). The particles were spherical with the average particle size between 10 and 20 nm in diameter with a moderate degree of nanoclustering (ca.150-200 particles/cluster). In terms of adsorption properties, the PDMAEMA@MNPs exhibited a higher BPA adsorption capacity (1.05 mg/g MNP at pH 9) than the quaternized form (0.50 mg/g MNP at pH 9). Equilibrium isotherm, kinetic, and thermodynamic characteristics of BPA adsorption on the PDMAEMA@MNPs were investigated. It was found that the BPA adsorption …

Elastic Properties Of Boro-Tellurite Glasses Doped With Europium Oxide, Chinnappareddy Devaraja, G. V. Jagadeesha Gowda, Bheemaiah Eraiah, G. K. Narasihma Murthy

Journal of Metals, Materials and Minerals

The glass series of xEu2O3-5PbO-25TeO2-(70-x) B2O3, where x=0.1 mol% to 0.6 mol% were prepared by employing the conventional melt quenching method. The non-crystallinity of prepared BTE glasses was examined by the X-ray diffraction method. The very important mechanical properties such as elastic moduli, Debye temperature, Poisson’s ratio, fractional bond connectivity, softening temperature, acoustic impedance, and the thermal expansion coefficient of the BTE glasses have been studied by measuring ultrasonic velocity. The experimental results indicate that the calculated parameters strongly depend on increasing Eu2O3 concentration. The elastic moduli of the prepared samples were found to decrease with Eu2O3 concentration and this …

Enhanced Photocatalytic Activity Of Zno Nanostructures Deposited On Mesh Through Electrochemical Deposition And Thermal Oxidation, Chantana Aiempanakit, Thongchai Phantaporn, Kamon Aiempanakit

Journal of Metals, Materials and Minerals

This article reported that the properties of zinc oxide (ZnO) nanostructures were modified by the thermal oxidation process at different temperatures in the range of 200℃ to 600℃ for 1 h. The Zn films were deposited on a stainless steel mesh by using the electrochemical deposition technique. The elemental composition of Zn and O was exhibited via energy-dispersed X-ray spectroscopy in which the atomic ratio of O/Zn increased with the increase of oxidation temperature. The results showed that oxidation temperature has a significant effect on the morphological and crystal structure. The nanosheet structure of the as-deposited film transferred to the …

Brazilein Modified Zinc Oxide Nanorods With Enhanced Visible Light-Responsive Photocatalytic Efficiency, Montri Aiempanakit, Penpicha Sudjai, Kittiyaporn Singsumphan, Sakchai Laksee, Cheewita Suwanchawalit

Journal of Metals, Materials and Minerals

Photocatalytic efficiency of ZnO nanorods has been investigated with respect to the concentration of brazilein. Brazilein modified ZnO nanorods were prepared by an impregnation process with 1.0%w/v, 2.5%w/v, and 5.0%w/v of brazilein solution.  In order to correlate the variation in concentration distributions and photocatalytic performance, the phase composition, optical properties, and photo-catalytic activities of brazilein modified ZnO nanorods prepared with different brazilein concentrations have been investigated and compared to an unmodified ZnO nanorods. The photocatalytic properties were measured in terms of indigo carmine degradation under visible light irradiation. It was found that ZnO nanorods with the highest visible light-responsive photocatalytic …

Extraction Of Molybdenum From A Spent Hds Catalyst Using Alkali Leaching Reagent, Chatisa Kansomket, Piamsak Laokhen, Tanongsak Yingnakorn, Tapany Patcharawit, Sakhob Khumkoa

Journal of Metals, Materials and Minerals

This research investigated extraction of molybdenum from spent hydrodesulfurization (HDS) catalyst used in petroleum refinery. The spent HDS catalyst still however contains significant amounts of valuable metals such as molybdenum and nickel for example, thereby recovery of such metals are of great interest. Pyro-hydrometallurgical process was utilized in this research to selectively extract molybdenum from the spent HDS catalyst using alkali leaching reagent. The process start from calcination of spent HDS catalyst, alkali leaching using sodium carbonate, purification by carbon adsorption-desorption, precipitation of ammonium molybdate and finally calcination to give molybdenum trioxide (MoO3) as the final recycling product. Effects of …

Recovery Of Nickel From Spent Electroplating Solution By Hydrometallurgical And Electrometallurgical Process, Piamsak Laokhen, Natthicha Ma-Ud, Tanongsak Yingnakorn, Tapany Patcharawit, Sakhob Khumkoa

Journal of Metals, Materials and Minerals

Recovery of nickel from spent electro nickel plating solution has been investigated via hydro-metallurgical and electrometallurgical processes. Experimental consisted of 3 steps, including precipitation of nickel from spent solution, leaching of nickel precipitate, and electrowinning of nickel. Nickel precipitation was performed using sodium hydroxide. Leaching parameters such as 1 M to 3 M sulfuric acid concentration, 100 g×L-1 to 300 g×L-1 solid to liquid ratio, and 30 min to 180 min leaching time were investigated. The leachate from the optimal leaching condition was further used as an electrolyte in electrowinning process. Effects of 3.3 V to 3.7 V cell voltage …

Development Of Aggregate From Bottom Ash In Environmentally Friendly Concrete, Udomvit Chaisakulkiet, Nattapong Makaratat, Sumrerng Rukzon

Journal of Metals, Materials and Minerals

This research presents a study of bottom ash for using as fine and coarse aggregates in concrete, B-F and B-C, respectively. Results of compressive strength and durability of the concrete containing B-F and B-C aggregates were investigated. Normal fine and coarse aggregates were replaced with the B-F and B-C aggregates at 0, 25, 50, 75 and 100% by weight of the normal aggregates. The results showed that the compressive strengths of the concretes were increased when the B-F and B-C aggregates were used at replacement levels of 25% and 50%. The water absorption and chloride resistances of the concretes were …