Engineering Commons^™

Let's Get Serious About It: Plastic-Free Campus Initiative, Geoffrey Kain, Camdyn Doucette, Regan Bossie

Sustainability Conference

On February 23, 2022, the UN agreed to start negotiating a world-first global treaty on plastic waste--since nearly 200 nations unanimously agreed to move toward a legally binding plastics treaty by 2024. In 2019 the UN Environmental Programme report highlighted that "our world is drowning in plastic." As with the climate change crisis (to which plastics production and disposal are also linked), the data resoundingly illustrate the imminent systemic threat that disposable plastics pose to the world's seas, freshwater sources, soils, food supply, air, and species. Nevertheless, plastics production is predicted to rise dramatically over the next 20 years, with …

Method Of Embedded Imperfections For The Direct Simulation Of Deformation Instabilities In Film-Substrate Structures, Siavash Nikravesh Kazeroni

Mechanical Engineering ETDs

In this dissertation, a novel finite-element methodology called “embedded imperfections” is proposed and employed for computationally simulating various types of deformation instabilities observed in film-substrate structures subjected to mechanical loading. The approach involves the incorporation of elements having distinctive material properties within the film-substrate interface. One can interpret this practice as a deliberate distribution of material defects within the numerical model. It has been shown that embedded imperfections not only can trigger the onset of instability, but also can lead to “direct” simulation of deformation instability problems in that primary and subsequent instability modes can all be captured in a …

Magnetic And Structural Effects In Interfacial Magnetism: Molecular Magnets And Ferrimagnetic Alloys, Jenae E. Shoup

USF Tampa Graduate Theses and Dissertations

Magnetic thin films are important for technological applications such as giant magnetoresistance,spin valves and magnetic tunnel junctions. A key feature for these applications to be possible is the interface between two materials. We will be studying two types of thin film magnetism; interfaces between molecular carbon, C60, and non-magnetic/ferromagnetic material and two layers of ferrimagnetic rare earth/ transition metal alloys (RE/TM) that have similar composition to engineer a magnetic tunable interface.

One of the most unexpected spin-related properties of C60 is the emergence of room-temperature ferromagnetism in multilayer films of C60 and non-ferromagnetic transition metals such as Cu or Mn …

Limits Of Detection Of Mycotoxins By Laminar Flow Strips: A Review, Xinyi Zhao, Hugh Byrne, Christine M. O’Connor, James Curtin, Furong Tian

Articles

Mycotoxins are secondary metabolic products of fungi. They are poisonous, carcinogenic, and mutagenic in nature and pose a serious health threat to both humans and animals, causing severe illnesses and even death. Rapid, simple and low-cost methods of detection of mycotoxins are of immense importance and in great demand in the food and beverage industry, as well as in agriculture and environmental monitoring, and, for this purpose, lateral flow immunochromatographic strips (ICSTs) have been widely used in food safety and environmental monitoring. The literature to date describing the development of ICSTs for the detection of different types of mycotoxins using …

Theranostic Copolymers Neutralize Reactive Oxygen Species And Lipid Peroxidation Products For The Combined Treatment Of Traumatic Brain Injury, Aaron Priester, Richard Waters, Ashleigh Abbott, Krista Hilmas, Klaus Woelk, Hunter A. Miller, Aria W. Tarudji, Connor C. Gee, Brandon Mcdonald, Forrest M. Kievit, Anthony J. Convertine

Chemistry Faculty Research & Creative Works

Traumatic brain injury (TBI) results in the generation of reactive oxygen species (ROS) and lipid peroxidation product (LPOx), including acrolein and 4-hydroxynonenal (4HNE). The presence of these biochemical derangements results in neurodegeneration during the secondary phase of the injury. The ability to rapidly neutralize multiple species could significantly improve outcomes for TBI patients. However, the difficulty in creating therapies that target multiple biochemical derangements simultaneously has greatly limited therapeutic efficacy. Therefore, our goal was to design a material that could rapidly bind and neutralize both ROS and LPOx following TBI. To do this, a series of thiol-functionalized biocompatible copolymers based …

Machine Learning Assisted Discovery Of Shape Memory Polymers And Their Thermomechanical Modeling, Cheng Yan

LSU Doctoral Dissertations

As a new class of smart materials, shape memory polymer (SMP) is gaining great attention in both academia and industry. One challenge is that the chemical space is huge, while the human intelligence is limited, so that discovery of new SMPs becomes more and more difficult. In this dissertation, by adopting a series of machine learning (ML) methods, two frameworks are established for discovering new thermoset shape memory polymers (TSMPs). Specifically, one of them is performed by a combination of four methods, i.e., the most recently proposed linear notation BigSMILES, supplementing existing dataset by reasonable approximation, a mixed dimension (1D …

Effects Of Carrier, Leveller, And Booster Concentrations On Zinc Plating From Alkaline Zincate Baths, Abdul Jalil Mohammed, Michael S. Moats

Materials Science and Engineering Faculty Research & Creative Works

Organic additives are required for alkaline zincate plating baths to obtain an acceptable coating on steel for corrosion protection. The effects and possible interactions of three commercial additives (Eldiem Carrier, Eldiem Booster, and Bright Enhancer 2x on zinc electrodeposition from a high-concentration alkaline zincate bath were investigated. Visually acceptable deposits were produced within the current density range of 130 to 430 A m^-2 for most additive conditions examined. Over concentration ranges examined, decreasing the booster concentration led to brighter zinc deposits, and an interaction between the carrier and the booster was detected. The additives fostered the formation of compact …

Mechanical Behavior Of Materials, Joshua P. Steimel

Pacific Open Texts

This text serves to cover in more detail solid mechanics concepts and specifically the material response to stress and strain. This text spans solid mechanics concepts from stress and strain at an atomistic length scale, to linear elasticity, anisotropy, linear viscoelasticity, plasticity, dislocation generation and interactions, and fracture.

Quasi In-Situ Ebsd Analysis Of Twinning-Detwinning And Slip Behaviors In Textured Az31 Magnesium Alloy Subjected To Compressive-Tensile Loading, Yuzhi Zhu, Dewen Hou, Qizhen Li

Materials Science and Engineering Faculty Publications and Presentations

Twinning and detwinning behavior, together with slip behavior, are studied in a textured AZ31 magnesium alloy under compressive and tensile strains along the rolling direction (RD) after each interrupted mechanical test via quasi in-situ electron backscattered diffraction technique. The results show that twinning firstly takes place under the compressive strain along the RD. With the increasing compressive strain, {1012} tensile twins firstly nucleate, then propagate, and finally thicken. While under a reversed tensile strain along the RD, detwinning occurs. No nucleation happens during detwinning. Thus, tensile twins can detwin at lower tensile strain, followed by thinning, shortening, and vanishing. Slips …

Prediction Of Concrete Strengths Enabled By Missing Data Imputation And Interpretable Machine Learning, Gideon A. Lyngdoh, Mohd Zaki, N.M. Anoop Krishnan, Sumanta Das

Faculty Publications - Biomedical, Mechanical, and Civil Engineering

Machine learning (ML)-based prediction of non-linear composition-strength relationship in concretes requires a large, complete, and consistent dataset. However, the availability of such datasets is limited as the datasets often suffer from incompleteness because of missing data corresponding to different input features, which makes the development of robust ML-based predictive models challenging. Besides, as the degree of complexity in these ML models increases, the interpretation of the results becomes challenging. These interpretations of results are critical towards the development of efficient materials design strategies for enhanced materials performance. To address these challenges, this paper implements different data imputation approaches for enhanced …

Impulse, Spring 2022, University Marketing And Communications, Jerome J. Lohr College Of Engineering

Impulse (Jerome J. Lohr College of Engineering Publication)

2 | Ahmed Leads Construction and Operations Management
4 | Faculty News
8 | Kelley Steps Aside After 44 Years
12 | Boggs Retires From Mechanical Engineering
14 | Looking At Covid-19 Numbers
16 | Students Help College of Nursing
18 | Midwest Applied Materials Symposium Debuts
20 | Fourth Data Science Event Takes Place
24 | College Achievements
26 | Hard Work Pays Off
28 | Spotlight Shines on Students
30 | Mentoring Program Takes Off
32 | Robotics Club Busy With Activities
34 | The Numbers
36 | Brown, Sieve Honored
38 | Alumna Leads NASA Division
40 …

Investigation Of The Structure, Chemistry And Functional Performance Of Novel Biochars, Julie Elizabeth Muretta

Graduate Theses & Non-Theses

Biochars are a class of carbonaceous materials possessing high degrees of structural and chemical disorder in both organic and inorganic constituent phases. Despite this disorder, and in some cases because of this disorder, biochars have shown strong performance in adsorbing and even sequestering contaminants from soil, surface water and air. Biochar is the carbonaceous, solid product of heating carbonaceous feedstock in an oxygen-limited environment above 250°C, usually sourced from inexpensive, locally available agricultural and forestry wastes which can otherwise be difficult and expensive to dispose of. Biochar possesses attractive functional properties like high specific surface area, high micropore volume, and …

Synthesis And Stabilization Of Gold Nanoparticles From Chloride And Cyanide Systems, Kathryn Ariela Bozer

Graduate Theses & Non-Theses

Generating gold nanoparticles (AuNPs) from gold chloride solution by precipitating with compounds can be difficult due to the potentially required high temperatures. Tin chloride can be used to overcome this dilemma. The process that is known to make Purple of Cassius is a method where gold chloride and tin chloride solutions are mixed to form AuNPs and tin oxide precipitate. However, it is modified by adding hydrazine to resolubilize the tin oxide and provide a more stable solution for the AuNPs. A three-factor central composite experimentally designed model was created using Design Expert incorporating pH, temperature, and gold concentration as …

The Tempering Response Of Cpm® 3v Tool Steel Investigated Through Tensile Testing And Microstructural Observations, Stephen A.C. Hanson

Graduate Theses & Non-Theses

Heat treatment, tensile testing failure analysis, and microstructural evaluation of the Crucible Industries tool steel CPM® 3V was undertaken to investigate CPM® 3V’s tempering response for the following samples: As-Hardened (no tempering); tempered at 450°C, 550°C, 650°C, and 700°C; and As-Received (annealed). CPM® 3V tool steel is manufactured by Crucible Industries using their proprietary Crucible Particle Metallurgy (CPM®) technology. This material was heat-treated at four different tempering temperatures and was evaluated for tensile properties according to ASTM E8. A TMS landmark tensile fixture was used to establish the ultimate tensile strength and the yield strength of the material for the …

Effect Of Micro-Structural Dispersity Of Simo Ductile Iron On High Temperature Performance During Static Oxidation, Simon N. Lekakh, Asebi Bofah, Larry A. Godlewski, Mei Li

Materials Science and Engineering Faculty Research & Creative Works

High silicon and molybdenum (SiMo) ductile iron is commonly used for car exhaust systems, and its micro-structural dispersity depends on intrinsic parameters, which include alloy composition and inoculation efficiency, as well as extrinsic factors, such as casting wall thickness and molding material, which define cooling rate during solidification. Micro-structural dispersity is referred to as the degree of heterogeneity of sizes of structural constituencies within the microstructure. A variation in the micro-structural dispersity could impact the high temperature performance of SiMo ductile iron during static oxidation and transient thermo-mechanical loading conditions. In this study, static high temperature tests were performed on …

Effects Of Carrier, Leveller, And Booster Concentrations On Zinc Plating From Alkaline Zincate Baths, Abdul Jalil Mohammed, Michael S. Moats

Materials Science and Engineering Faculty Research & Creative Works

Organic additives are required for alkaline zincate plating baths to obtain an acceptable coating on steel for corrosion protection. The effects and possible interactions of three commercial additives (Eldiem Carrier, Eldiem Booster, and Bright Enhancer 2x on zinc electrodeposition from a high-concentration alkaline zincate bath were investigated. Visually acceptable deposits were produced within the current density range of 130 to 430 A m−2 for most additive conditions examined. Over concentration ranges examined, decreasing the booster concentration led to brighter zinc deposits, and an interaction between the carrier and the booster was detected. The additives fostered the formation of compact and …

The Oxidation Of The Hisimo Cast Irons Alloyed With Cr/Al At 800 °C, Wenhui Zhu, Bruce A. Pint, Yang Huo, Larry Godlewski, Bita Ghaffari, Simon Lekakh, Carlos Engler-Pinto, Mei Li

Materials Science and Engineering Faculty Research & Creative Works

To improve the oxidation resistance of cast iron containing Si and Mo (HiSiMo), 1wt.% Cr and 3wt.% Al were added into the base alloy to improve high temperature oxidation resistance for exhaust manifold applications. Oxidation tests were performed in both dry and wet air (air + 10% H2O) at 800 °C for 1, 10, 24, and 50 h. The mass change and oxide thickness were measured to evaluate the oxidation resistance. Scanning electron microscopy with energy dispersive X-ray spectroscopy (SEM/EDS) and transmission electron microscopy (TEM) were employed to characterize the oxidized samples. The results showed that the additions of Al …

Water Based Soil Fluidization Using A Soft Eversion Robot, James E. Hand

Doctoral Dissertations and Master's Theses

Soft robotics, a form of robotics that incorporates nonrigid components, continues to grow in scope, system design, and application. A recent addition to this field is the Vine Robot platform, a bio-inspired robot designed by Stanford University in 2017. Its method of movement, known as eversion, closely resembles the way that a vine grows along a tree, giving it its name. The focus of this research was to take its proven abilities of underwater vine-like movement and soil fluidization, a process where granular materials are converted from a solid-like state to a fluid-like state, to create an underwater eversion robot …

Rapid Removal Of Pfoa And Pfos Via Modified Industrial Solid Waste: Mechanisms And Influences Of Water Matrices, Hongyi Wan, Rollie Mills, Kai Qu, James C. Hower, M. Abdul Mottaleb, Dibakar Bhattacharyya, Zhi Xu

Chemical and Materials Engineering Faculty Publications

Emerging perfluoroalkyl and polyfluoroalkyl substances contaminate waters at trace concentrations, thus rapid and selective adsorbents are pivotal to mitigate the consequent energy-intensive and time-consuming issues in remediation. In this study, coal combustion residuals-fly ash was modified (FA-SCA) to overcome the universal trade-off between high adsorption capacity and fast kinetics. FA-SCA presented rapid adsorption (teq = 2 min) of PFOX (perfluorooctanoic acid and perfluorooctanesulfonic acid, collectively), where the dynamic adsorption capacity (qdyn = qm/teq) was 2–3 orders of magnitude higher than that of benchmark activated carbons and anion-exchange resins. Investigated by advanced characterization and kinetic models, the fast kinetics and superior …

The Tin Man Needs A Heart: A Proposed Framework For The Regulation Of Bioprinted Organs, Linda Foit

Fordham Law Review

Each day, seventeen people die in the United States while waiting for an organ transplant. At least part of this need could be met by bioprinting, a technology that allows the on-demand production of custom-sized organs from a patient’s own cells. The field of bioprinting is progressing rapidly: the first bioprinted organs have already entered the clinic. Yet, developers of bioprinted organs face significant uncertainty as to how their potentially lifesaving products will be regulated—and by which government agency. Such regulatory uncertainty has the potential to decrease investment and stifle innovation in this promising technological field. This Note examines how …

Block Copolymer Directed Self-Assembly: Exploring The Efficacy Of Applications In Semiconductor Fabrication, Jakin Bryce Delony

USF Tampa Graduate Theses and Dissertations

Over the course of the past 80 years, semiconductor devices have become increasingly ubiquitous in everyday life.From constructing mainframes that encompassed entire rooms during the 1940s, to inventing personal computers in the 1980s, to developing progressively faster smartphones and wearable technology in the 2010s, the primary driving force behind the Digital Revolution has been increasing transistor counts, and thus computing power, via incremental improvements in optical lithography. In 1965, Intel co-founder Gordon Moore boldly predicted that the transistor density of semiconductor devices would double approximately every 18-24 months. While this prediction -- now colloquially referred to as Moore's Law -- …

Polyaniline/Cobalt Nanoparticle Composite Films, Rifat Mahbub

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Polymer nanocomposites have been gaining attention because of the enhanced properties of the element materials it can offer. These composites have been used in biological sector as well as quantum computing and memory devices. These are also used as different kind of sensors. Polymer composites incorporated with magnetic nanoparticles can modify the magnetic property of the nanoparticles and that has huge potential to be used in different sort of applications.

This work aims to develop a polymeric nanocomposite incorporating a conducting polymer and magnetic nanoparticles. The influence of the conducting polymer on the magnetic property of the nanoparticles was investigated. …

Characterization Of Disorder And Its Effects On Two-Dimensional Transition Metal Dichalcogenides, Krystal Rose York

Dissertations

Since the discovery of the unique electrical properties of graphene in 2004, there has been an increased interest in two-dimensional (2D) materials. However, graphene is known as a zero-gap semi-metal, thus spurring further research in order to find suitable 2D semiconductor materials. Transition metal dichalcogenides (TMDs) are a class of layered materials that have recently attracted attention. In particular, MoS2, MoSe2, WS2, and WSe2 have direct band gaps in their monolayer form and favorable electrical properties, making them promising materials for both electronic and optoelectronic applications. Like many 2D materials, studies in semiconductor TMD materials began with mechanically exfoliated sheets …

Soft Magnetic Composite Substrates For Rf/Microwave Applications, Poonam Lathiya

USF Tampa Graduate Theses and Dissertations

Novel soft magnetic ferrite materials will play a crucial role in next-generation over one trillion sensors (also known as “trillion sensor economy) related to 5G communications and internet of things, as these materials can achieve improved wireless power and signal transfer efficiency with high operation frequency. In this work, Ni-Cu-Zn and Ni-Co-Zn ferrites with high permeability, high permittivity, and low magnetic and dielectric losses were prepared for RF and microwave device applications. Frequency dispersion of RF complex permeability of Ni-Cu-Zn ferrites prepared under different applied hydraulic pressures and durations have been thoroughly investigated. The Ni0.35Cu0.19Zn0.46Fe2O4 ferrites were prepared by conventional …

Tuning Between Quenching And Energy Transfer In Dna-Templated Heterodimer Aggregates, Azhad U. Chowdhury, Jonathan S. Huff, Matthew S. Barclay, Lance K. Patten, Aaron Sup, Natalya Hallstrom, Jeunghoon Lee, Paul H. Davis, Daniel B. Turner, Bernard Yurke, William B. Knowlton, Ryan D. Pensack

Materials Science and Engineering Faculty Publications and Presentations

Molecular excitons, which propagate spatially via electronic energy transfer, are central to numerous applications including light harvesting, organic optoelectronics, and nanoscale computing; they may also benefit applications such as photothermal therapy and photoacoustic imaging through the local generation of heat via rapid excited-state quenching. Here we show how to tune between energy transfer and quenching for heterodimers of the same pair of cyanine dyes by altering their spatial configuration on a DNA template. We assemble “transverse” and “adjacent” heterodimers of Cy5 and Cy5.5 using DNA Holliday junctions. We find that the transverse heterodimers exhibit optical properties consistent with excitonically interacting …

Effects Of Annealing Ambient On The Structural, Optical And Electrical Properties Of Tio2:Ge Thin Films, Lilian A. Owino, Sebastian Waita, Robinson J. Musembi, Francis W Nyongesa

Tanzania Journal of Science

TiO2, a semiconducting material with a wide energy band gap, has been researched intensively due to its interesting properties and many potential applications. The films properties can as well be modified by preparing the films under diverse ambient to suit diverse applications. In this work, the effects of the annealing atmosphere on the structural, optical and electrical properties of pure TiO2 and TiO2:Ge composite thin films deposited by sputtering from commercially available pure TiO2 and TiO2:Ge (85:15) targets respectively were studied. The films were deposited on fluorine doped tin oxide glass substrates by radio frequency magnetron sputtering technique at room …

Method Of Making Hinged Self-Referencing Fabry–Pérot Cavity Sensors, Jeremiah C. Williams, Hengky Chandrahalim

AFIT Patents

A method is provided for fabricating a passive optical sensor on a tip of an optical fiber. The method includes perpendicularly cleaving a tip of an optical fiber and mounting the tip of the optical fiber in a specimen holder of a photosensitive polymer three-dimensional micromachining machine. The method includes forming a three-dimensional microscopic optical structure within the photosensitive polymer that comprises a two cavity Fabry-Perot Interferometer (FPI) having a hinged optical layer that is pivotally coupled to a suspended structure. The method includes removing an uncured portion of the photosensitive polymer using a solvent. The method includes depositing a …

Nanofibers For Renewable Energy, Michael Wildy, Ping Lu

College of Science & Mathematics Departmental Research

Electrospinning is a straightforward technique for the fabrication of nanofibers with the potential for various applications. Thermal energy storage systems using electrospun nanofibers have gained researchers’ attention due to its desirable properties such as nanoscale diameter, large surface area, excellent thermal conductivity, and high loading and thermal energy storage capacity. The encapsulation of phase change materials (PCMs) in electrospun nanofibers for storing renewable thermal energy can be achieved by uniaxial electrospinning of a blend of PCM and polymer, coaxial electrospinning of a PCM core and a polymer sheath, or post-electrospinning absorption. The PCM content and thermal energy storage capacity of …

In Situ Characterization Of Electrode Structure And Catalytic Processes In The Electrocatalytic Oxygen Reduction Reaction, Ya-Chen Feng, Xiang Wang, Yu-Qi Wang, Hui-Juan Yan, Dong Wang

Journal of Electrochemistry

As an electrochemical energy conversion system, fuel cell has the advantages of high energy conversion efficiency and high cleanliness. Oxygen reduction reaction (ORR), as an important cathode reaction in fuel cells, has received extensive attention. At present, the electrocatalysts are still one of the key materials restricting the further commercialization of fuel cells. The fundamental understanding on the catalytic mechanism of ORR is conducive to the development of electrocatalysts with the enhanced activity and high selectivity. This review aims to summarize the in situ characterization techniques used to study ORR. From this perspective, we first briefly introduce the advantages of …

In-Situ/Operando57Fe Mössbauer Spectroscopic Technique And Its Applications In Nife-Based Electrocatalysts For Oxygen Evolution Reaction, Jafar Hussain Shah, Qi-Xian Xie, Zhi-Chong Kuang, Ri-Le Ge, Wen-Hui Zhou, Duo-Rong Liu, Alexandre I. Rykov, Xu-Ning Li, Jing-Shan Luo, Jun-Hu Wang

Journal of Electrochemistry

The development of highly efficient and cost-effective electrocatalysts for the sluggish oxygen evolution reaction (OER) remains a significant barrier to establish effective utilization of renewable energy storage systems and water splitting to produce clean fuel. The current status of the research in developing OER catalysts shows that NiFe-based oxygen evolution catalysts (OECs) have been proven as excellent and remarkable candidates for this purpose. But it is critically important to understand the factors that influence their activity and underlying mechanism for the development of state-of-the-art OER catalysts. Therefore, the development of in-situ/operando characterizations is urgently required to detect key intermediates along …