Engineering Commons^™

Comparing Weathering Effects Of Ultraviolet And Xenon Arc Accelerated Aging On Polyvinyl Chloride, Collin Mcinnes

Williams Honors College, Honors Research Projects

As the ubiquitousness of polymers increases and begins seeing use in outdoor settings, the need to fully understand how these materials degrade is also necessary. This study aims to compare two known accelerated aging methods, namely an ultraviolet light chamber and a xenon arc light chamber, to understand what differences, if any, manifest in the mechanical, chemical, and cosmetic deterioration of polyvinyl chloride (PVC) after long-term exposure. The study utilizes Fourier-transform infrared spectroscopy, dynamic mechanical analysis, thermogravimetric analysis, and colorimetry analysis to determine the extent of degradation and potential discrepancies between the aging methods.

Development Of High Current Electromigration Test System For Evaluation Of Novel Solder Structures, Nicholas Pareis

Electronic Theses and Dissertations, 2020-2023

Electromigration reliability of ball-grid-array (BGA) solder joints is emerging as a critical area of research for advanced microelectronic devices, especially those with high power requirements. In this study, a novel high current electromigration test system, including a temperature sensing capability, was designed and developed for the purpose of performing electromigration characterization of various BGA solder joint structures, including features designed for reduced current crowding. This study consisted of two main parts: design and development of a novel high current electromigration test system, and using this novel system for electromigration characterization of BGA solder joints. In the first portion of this …

Xps Study Of Calcium Lanthanum Sulfide Ceramics, Brian E. Butkus

Graduate Thesis and Dissertation 2023-2024

Long wave infrared (LWIR) optics that transmit in the 8 to 14 m wavelength range and, additionally, can withstand severe physical and thermal stresses are needed for advanced remote sensing, guidance and communication-based applications. However, most non-oxide transparent LWIR optics do not have the wider transmission range, nor the hardness and resistance to thermal shock needed for extreme environments. Because of these limitations, research is circling back to a promising material, calcium lanthanum sulfide (CLS), that could meet LWIR needs for extreme environments.

In this thesis, we will demonstrate the abilities of x-ray photoelectron spectroscopy (XPS) as a technique for …

Functionalization Of 1d And 2d Nanostructures And Their Applications, Yuen Yee Li Sip

Graduate Thesis and Dissertation 2023-2024

Material discovery and development has been playing a significant role in shaping human civilizations, by studying and improving materials for appealing observations to aid in our survival as well as to satisfy our curiosity. From the common earthly materials that give us strong building structures and hunting weapons to the Silicon Age that contributes to the creation of modern electronics and computers, the development of novel and enhanced materials continues to grow. Recently, a new field has emerged that is rapidly expanding the engineering circle; these are called nanomaterials. By shrinking bulk materials into structures with nanoscale dimensions, there is …

Machine Learning Strategies For Potential Development In High-Entropy Driven Nickel-Based Superalloys, Marium Mostafiz Mou

Graduate Theses/Dissertations

In this study, I developed Deep Learning interatomic potentials to model a multi-phase and multi-component system of Ni-based Superalloys. The system has up to three major phase constituents, namely Gamma, Gamma Prime, and Transition-metal rich Carbide. I utilized invariant scalar-based and/or equivariant, tensor-based neural network (NN) approach as implemented in DEEPMD, NEQUIP/ALLEGRO codes, respectively, and Moment Tensor Potential (MTP). For the training and validation sets, I employed the ab-initio molecular dynamics (AIMD) trajectory results and ground state DFT calculations, including the energy, force, and virial database from highly diverse compositions, temperatures, and pressures following a “High Entropy Strategy.” The Deep …

Development Of Advanced Germanium Detectors For Rare Event Physics, Sanjay Bhattarai

Dissertations and Theses

High Purity Germanium (HPGe) detectors are widely used in rare-event physics searches for dark matter, neutrinoless double-beta decay, and solar neutrinos. This dissertation fo- cuses on improving crystal quality by controlling the impurity concentration, dislocation density, and growth environment as well as developing advanced Ge detectors for various physics applications. The dissertation presents experimental investigations of electrical conduction mechanisms in p-type amorphous germanium (a-Ge), which is used as an elec- trical contact material in HPGe detectors. By measuring the surface leakage current from three high-purity planar Ge detectors, we determine the localization length and hopping parameters in a-Ge. The dissertation …

A Thermal, Mechanical, And Materials Framework For A Shape Memory Alloy Heat Engine For Thermal Management And Energy Recovery, Maria Chikhareva

Electronic Theses and Dissertations, 2020-2023

Shape memory alloy (SMA) heat engines possess an inherent property of sensing a change in temperature, performing work, and rejecting heat through the shape memory effect resulting from a temperature-induced phase transformation. This work presents a framework for the design and implementation of an SMA-based Stirling heat engine for maximum power or speed incorporating and combining mechanical, thermal, and material aspects. The motivation for this work comes from the growing need for reliable thermal management and energy recovery in both ground and space applications of interest to NASA and commercial space companies. In future lunar and Mars missions, an SMA …

Investigation Of Fiber Orientation And Mechanical Properties Of Pyrolysis Recycled Carbon-Fiber Reinforced Thermoset Composite, Reva N. Simmons, Harry Lee, Garam Kim

Discovery Undergraduate Interdisciplinary Research Internship

With increasing demand of carbon fiber reinforced fiber thermoset composites, establishing a sustainable cycle for these materials becomes crucial. Pyrolysis is a process of reclaiming carbon fiber from thermoset composites by thermally degrading the polymer at high temperatures allowing the fibers to be extracted. Carbon fiber reclaimed through current pyrolysis processes for thermoset composites typically loses its original shape and orientation, making it difficult to reorganize the fibers. This study investigated the feasibility of maintaining the fiber orientations for continuous fiber reinforced thermoset composite during pyrolysis by stitching the carbon fiber layup to a conformable copper mesh during the manufacturing …

Development And Testing Of A Hyperbaric Aerodynamic Levitator For Containerless Materials Research, Sydney Elizabeth Boland

Masters Theses

"This research focused on the development and testing of a hyperbaric aerodynamic levitator for container less materials research of specimens at temperatures greater than 2000°C and pressures up to 10.3 MPa (1500 psi). The effect of specimen size, specimen density, pressure, and flow rate on the levitation behavior was studied. Lightweight specimens demonstrated two stable levitation regimes that were speculated to be associated with a change in the turbulent wake structure. The hyperbaric aerodynamic levitator was also used to determine the effect of pressure on the heat transfer by studying the melting behavior of a levitated 3.0 mm diameter alumina …

Laser Powder Bed Fusion Of Bimetallic Structures, Asif Mahmud

Graduate Thesis and Dissertation 2023-2024

Laser powder bed fusion (LPBF) is a popular additive manufacturing (AM) technique that has demonstrated the capability to produce sophisticated engineering components. This work reports the crack-free fabrication of an SS316L/IN718 bimetallic structure via LPBF, along with compositional redistribution, phase transformations and microstructural development, and nanohardness variations. Constituent intermixing after LPBF was quantitatively estimated using thermo-kinetic coefficients of mass transport and compared with the diffusivity of Ni in the austenitic Fe-Ni system. The intermixing of primary solvents (Ni and Fe) in SS316L/IN718 bimetallic structures was observed for an intermixing zone of approximately 800 µm, and their intermixing coefficient was estimated …

Radiation Shielding Effectiveness Of Hafnium Diboride (Hfb2) Reinforced Epoxy Composites For Enhanced Radiation Protection And Safety, Furkan Erdogan

Theses and Dissertations

This thesis investigates the radiation shielding effectiveness of hafnium diboride (HfB2) reinforced epoxy composites, with the aim of enhancing radiation protection and safety in various applications. The study focuses on the development and characterization of HfB2-epoxy composites with varying weight percentages of HfB2 nanoparticles, as well as on the evaluation of their shielding effectiveness against gamma rays and thermal neutrons. The radiation shielding performance of the composites is assessed using gamma-ray spectroscopy and neutron counting, and the neutron attenuation efficacy is compared with that of 5% borated high-dense polyethylene. The results indicate that the HfB2-epoxy composites exhibit promising radiation shielding …

Deep Reinforcement Learning For Approximate Policy Iteration: Convergence Analysis And A Post-Earthquake Disaster Response Case Study, Abhijit Gosavi, L. (Lesley) H. Sneed, L. A. Spearing

Engineering Management and Systems Engineering Faculty Research & Creative Works

Approximate Policy Iteration (API) is a Class of Reinforcement Learning (RL) Algorithms that Seek to Solve the Long-Run Discounted Reward Markov Decision Process (MDP), Via the Policy Iteration Paradigm, Without Learning the Transition Model in the Underlying Bellman Equation. Unfortunately, These Algorithms Suffer from a Defect Known as Chattering in Which the Solution (Policy) Delivered in Each Iteration of the Algorithm Oscillates between Improved and Worsened Policies, Leading to Sub-Optimal Behavior. Two Causes for This that Have Been Traced to the Crucial Policy Improvement Step Are: (I) the Inaccuracies in the Policy Improvement Function and (Ii) the Exploration/exploitation Tradeoff Integral …

Performance Evaluation Of Composite Sandwich Structures With Additively Manufactured Aluminum Honeycomb Cores With Increased Bonding Surface Area, M. Rangapuram, S. K. Dasari, Joseph William Newkirk, K. Chandrashekhara, H. Misak, P. R. Toivonen, D. Klenosky, T. Unruh, J. Sam

Materials Science and Engineering Faculty Research & Creative Works

Modern aerostructures, including wings and fuselages, increasingly feature sandwich structures due to their high-energy absorption, low weight, and high flexural stiffness. The face sheet of these sandwich structures are typically thin composite laminates with interior honeycombs made of Nomex or aluminum. Standard cores are structurally efficient, but their design cannot be varied throughout the structure. With additive manufacturing (AM) technology, these core geometries can be altered to meet the design requirements that are not met in standard honeycomb cores. This study used a modified aluminum honeycomb core, with increased surface area on the top and bottom, as the core material …

Final-Stage Densification Kinetics Of Direct Current–Sintered Zrb2, Austin D. Stanfield, Steven M. Smith, Suzana Filipović, Nina Obradović, Vladimir Buljak, Gregory E. Hilmas, William Fahrenholtz

Materials Science and Engineering Faculty Research & Creative Works

Final-stage sintering was analyzed for nominally phase pure zirconium diboride synthesized by borothermal reduction of high-purity ZrO₂. Analysis was conducted on ZrB₂ ceramics with relative densities greater than 90% using the Nabarro–Herring stress–directed vacancy diffusion model. Temperatures of 1900°C or above and an applied uniaxial pressure of 50 MPa were required to fully densify ZrB₂ ceramics by direct current sintering. Ram travel data were collected and used to determine the relative density of the specimens during sintering. Specimens sintered between 1900 and 2100°C achieved relative densities greater than 97%, whereas specimens sintered below 1900°C failed to …

Antioxidant Theranostic Copolymer-Mediated Reduction In Oxidative Stress Following Traumatic Brain Injury Improves Outcome In A Mouse Model, Aria W. Tarudji, Connor C. Gee, Hunter A. Miller, Rylie Steffen, Evan T. Curtis, Aaron M. Priester, Anthony J. Convertine, Forrest M. Kievit

Materials Science and Engineering Faculty Research & Creative Works

Following a traumatic brain injury (TBI), excess reactive oxygen species (ROS) and lipid peroxidation products (LPOx) are generated and lead to secondary injury beyond the primary insult. A major limitation of current treatments is poor target engagement, which has prevented success in clinical trials. Thus, nanoparticle-based treatments have received recent attention because of their ability to increase accumulation and retention in damaged brain. Theranostic neuroprotective copolymers (NPC3) containing thiol functional groups can neutralize ROS and LPOx. Immediate administration of NPC3 following injury in a controlled cortical impact (CCI) mouse model provides a therapeutic window in reducing ROS levels at 2.08–20.83 …

Morphological And Structural Characterization Of Mgal2o4 Spinel, Nina Obradović, Suzana Filipović, William Fahrenholtz, Bojan A. Marinkovic, Jelena Rogan, Steva Lević, Antonije Đorđević, Vladimir B. Pavlović

Materials Science and Engineering Faculty Research & Creative Works

Magnesium aluminate has the spinel structure along with good mechanical, chemical, and thermal properties. Magnesium aluminate has a wide range of applications including refractory ceramics, optically transparent ceramic windows, and armors. Its low dielectric permeability and low loss tangent enable its applications for integrated electronic devices, as well. In this paper, MgO and Al₂O₃ powders were mixed in a one-to-one molar ratio and calcined at temperatures ranging from 1500 to 1800o C to produce phase pure spinel. Thereafter, pellets were crushed and treated in a planetary ball mill for 60 min to obtain a fine powder. All …

Effect Of Mechanical Activation On Carbothermal Synthesis And Densification Of Zrc, Nina Obradović, Lun Feng, Suzana Filipović, Miljana Mirković, Darko Kosanović, Jelena Rogan, William Fahrenholtz

Materials Science and Engineering Faculty Research & Creative Works

Zirconium carbide ceramics were prepared by carbothermal reduction of ZrO₂ and C that were mixed by high-energy ball milling. Powders were milled for times from 0 to 120 min in air. As milling time increased, the surface area of the powders increased, indicating significant particle size reduction. Milled powders were reacted at 1600 °C and then densified by spark plasma sintering at 2000 °C, which was sufficient to convert the starting powders to zirconium carbide. Unmilled powders did not reach full density. Milled powders reached full density, but ZrO₂ impurities were found for specimens prepared from powders milled …

Mechanical Properties Of Zrb2 Ceramics Determined By Two Laboratories, Jeffrey J. Swab, Jecee Jarman, William Fahrenholtz, Jeremy Lee Watts

Materials Science and Engineering Faculty Research & Creative Works

The mechanical properties for zirconium diboride (ZrB2) were measured at two laboratories and compared. Two billets of ZrB2 were prepared by hot-pressing commercial powder. The relative densities of the billets were >99% and with an average grain size of 5.9 ± 4.5 µm. Both laboratories prepared American Society for Testing and Materials (ASTM) C1161 B-bars for strength and ASTM C1421 bars with notch configuration A for fracture toughness. Specimens were machined by diamond grinding at the Army Research Laboratory (ARL) and electrical discharge machining (EDM) at Missouri S&T. Strength bars tested at Missouri S&T were polished to a.25 μm finish …

Improving Strength And Microstructure Of Sic Reticulated Porous Ceramic Through In-Situ Generation Of Sic Whiskers Within Hollow Voids, Ruoyu Chen, Kunshi Xie, Haipeng Zhu, Qun He, Saisai Li, Haiming Wen

Materials Science and Engineering Faculty Research & Creative Works

SiC Reticulated Porous Ceramic with Excellent Strength and High-Density Ceramic Struts Was Successfully Prepared using the Polymer Replica Method, Followed by Pressureless Sintering under a Buried Charcoal Atmosphere. First, a Polyurethane (PU) Template Was Coated with a Si Slurry and Then a SiC-Containing Slurry, and Subsequently Heated under the Buried Charcoal Atmosphere. to Ensure Excellent Coating Ability of the Slurries, the Viscosity, Thixotropy, and Yield Stresses of the Si Slurry Were Optimized by Adjusting the Content of the Thickening Agent. during Heating, Si in the Coating Layer Reacted with the Residual C and CO Gas from the PU Template and …

Advancing Aluminum Casting Optimization With Real-Time Temperature And Gap Measurements Using Optical Fiber Sensors At The Metal-Mold Interface, Bohong Zhang, Abhishek Prakash Hungund, Dinesh Reddy Alla, Deva Prasaad Neelakandan, Muhammad Roman, Ronald J. O'Malley, Laura Bartlett, Rex E. Gerald, Jie Huang

Materials Science and Engineering Faculty Research & Creative Works

Accurate measurement of interfacial heat transfer during casting solidification is crucial for optimizing metal solidification processes. The gap between the mold wall and the casting surface plays a significant role in heat transfer and cooling rates. In this study, two innovative fiber-optic sensors are employed to measure real-time mold gaps and thermal profiles during the solidification of A356 aluminum in a permanent mold casting. The experimental setup consists of a specially designed mold system made of unheated, uncoated tool steel, which facilitates easy installation of the fiber-optic sensors. An Extrinsic Fabry-Perot interferometric (EFPI) sensor is utilized to monitor the evolving …

The Angiogenic Potential Of Ph-Neutral Borophosphate Bioactive Glasses, Bradley A. Bromet, Nathaniel P. Blackwell, Nada Abokefa, Parker Freudenberger, Rebekah L. Blatt, Richard K. Brow, Julie A. Semon

Materials Science and Engineering Faculty Research & Creative Works

Borate bioactive glasses have gained attention in recent years due to their therapeutic and regenerative effects in vivo. However, borate bioactive glasses release alkaline ions, increasing the local pH and creating a toxic environment for cell culture studies. A partial compositional substitution of phosphate for borate can create a pH-neutral glass that does not significantly affect the local pH while still releasing therapeutic ions. In the present study, a series of Na-Ca-borophosphate bioactive glasses with different borate-to-phosphate ratios was evaluated in vitro and in vivo for cytotoxicity and angiogenic effects. Compared to more basic borate glasses, the pH-neutral glasses supported …

Exposure To Pcb126 During The Nursing Period Reversibly Impacts Early-Life Glucose Tolerance, Brittany B. Rice, Keegan W. Sammons, Sara Y. Ngo Tenlep, Madeline T. Weltzer, Leryn J. Reynolds, Cetewayo S. Rashid, Hollie I. Swanson, Kevin J. Pearson

Human Movement Studies & Special Education Faculty Publications

Polychlorinated biphenyls (PCBs) are persistent environmental organic pollutants known to have detrimental health effects. Using a mouse model, we previously demonstrated that PCB126 exposure before and during pregnancy and throughout the perinatal period adversely affected offspring glucose tolerance and/or body composition profiles. The purpose of this study was to investigate the glucose tolerance and body composition of offspring born to dams exposed to PCB126 during the nursing period only. Female ICR mice were bred, and half of the dams were exposed to either vehicle (safflower oil) or 1 µmole PCB126 per kg of body weight via oral gavage on postnatal …

Nanostructured Alloy Thin Film Fabrication And Application For Zinc-Air Battery And Lithium-Ion Battery, Guanzhi Wang

Electronic Theses and Dissertations, 2020-2023

The depletion of unsustainable fossil fuels and growing environmental issues have given rise to scientific challenges and research interests in the development of renewable energy technologies to meet the rising global energy demand. Electrochemical energy storage and conversion technologies (ESCTs), such as lithium-ion batteries, metal-air batteries, supercapacitors, and fuel cells, etc., offer a clean and sustainable strategy for utilizing energy. As the core components, the electrode materials, including anodes, cathodes, and catalysts, play a direct decisive role in the device's performance in practical application. Therefore, the development of high-performance and low-cost electrode materials is critical for the success of these …

Electroanalytical Investigations Of Microrna-Conjugated Cerium Oxide Based Nanomaterials For Biomedical Applications, Chaimae El Ghzaoui

Electronic Theses and Dissertations, 2020-2023

Diabetes patients are increasingly suffering from wound-healing impairments coupled with other severe medical conditions. High levels of oxidative stress and proinflammatory cytokines are predominant pathologic characteristics of diabetic wounds. Applying microRNA (miRNA) in gene therapy often successfully treats various disorders by generating highly specific bio-responses. Studies revealed that microRNA146a (miR146a), a regulator of inflammation, is downregulated in diabetic wounds. However, miR203 is found to be highly-expressed in diabetic foot ulcers in positive correlation with disease severity. We have synthesized Cerium oxide nanoparticles (CNPs) since they are used in various biomedical applications due to their high enzyme-mimetic activities and reactive oxygen …

Suppressing Aluminum/Silica Exchange Reaction Between High Aluminum Steel And Mold Flux During Continuous Casting Process, Kuanysh Nurbekuly Yermukhanbetov

Masters Theses

"Mold flux plays one of the critical roles in continuous casting of steel. It performs five primary functions: thermal and chemical insulation, lubrication between the steel strand and mold, absorption of inclusions, and promotion of even heat flux. The aluminum/silica exchange reaction occurring between steel and mold flux during the continuous casting process poses significant challenges in the steel industry. This reaction can lead to various defects in the cast product and adversely affect its surface quality, as well as downstream processing.

In this work, effectiveness of two approaches, namely slag dopant additions and electrochemical techniques, in suppressing the exchange …

Effect Of Platelet Length And Stochastic Morphology On Flexural Behavior Of Prepreg Platelet Molded Composites, Siavash Sattar, Benjamin Beltran Laredo, Sergii G. Kravchenko, Oleksandr G. Kravchenko

Mechanical & Aerospace Engineering Faculty Publications

Prepreg platelet molding compound (PPMC) can be used to create structural grade material with a heterogeneous mesoscale morphology. The present work considered various platelet lengths of the prepreg system IM7/8552 to study the effect of platelet length on the flexural behavior of PPMC composite. A progressive failure finite-element analysis was used to understand competing failure modes in PPMC with the different platelet length. The interlaminar and in-plane damage mechanisms were employed to describe complex failure modes within the mesostructure of PPMCs. Experimental results of the flexural tests of the PPMC with different platelet length sizes were used to validate the …

Temperature Monitoring In The Refractory Lining Of A Continuous Casting Tundish Using Distributed Optical Fiber Sensors, Muhammad Roman, Hanok Tekle, Dinesh Reddy Alla, Farhan Mumtaz, Jeffrey D. Smith, Laura Bartlett, Ronald J. O'Malley, Rex E. Gerald, Jie Huang

Materials Science and Engineering Faculty Research & Creative Works

This Article Explores the Prospects of using Spatially Distributed Optical Fiber Temperature Sensors based on Rayleigh Optical Frequency Domain Reflectometry (OFDR) Technology in the Continuous Casting of Molten Steel. the Measurement Capability of the Optical Fiber Sensors in a Simulated Steelmaking Environment Was Demonstrated using a Mock Refractory-Lined Tundish, Which Was Fabricated In-House. Single-Mode Optical Fibers, Contained in Protective Stainless-Steel Tubing, Were Embedded in the Refractory Lining of the Mock Tundish. the Instrumented Tundish Was Preheated Up to a Temperature of 960 °C (Recorded at the Surface of the Working Lining) Before the Molten Steel Pour. a Low-Alloy Steel (AISI …

A Study On The Impact Of Silicon And Manganese On Peritectic Behavior In Low Alloy Steels Assisted By Mold Thermal Mapping Technology And Shell Growth Measurements, Damilola Balogun, Muhammad Roman, Rex E. Gerald, Laura Bartlett, Jie Huang, Ronald J. O'Malley

Materials Science and Engineering Faculty Research & Creative Works

Non-Uniform Shell Growth Commonly Caused by the Peritectic Transformation in Low Carbon and Low Alloy Steels Has Been Directly Correlated with Mold Thermal Maps using a Mold Immersion Test into a Molten Steel Alloy. Mold Thermal Maps Were Obtained by Performing Real-Time Temperature Measurements with Optical Fibers Embedded 1 Mm from the Mold Working Surface. Shell Growth Measurements Were Obtained by 3D Optical Scanning of the Recovered Steel Shell Following Immersion Testing. the Effects of Silicon and Manganese on the Shell Growth and Mold Temperature Maps Have Been Examined in Relation to the Peritectic Transformation for Varying Carbon Contents. Results …

Synthesis, Densification, And Cation Inversion In High Entropy (Co,Cu,Mg,Ni,Zn)Al2o4 Spinel, Cole A. Corlett, Nina Obradovic, Jeremy Lee Watts, Eric W. Bohannan, William Fahrenholtz

Materials Science and Engineering Faculty Research & Creative Works

The synthesis, densification behavior, and crystallographic site occupancy were investigated for four different spinel-based ceramics, including a high-entropy spinel (Co_0.2Cu_0.2Mg_0.2Ni_0.2 Zn_0.2)Al₂O₄. Each composition was reacted to form a single phase, but analysis of X-ray diffraction patterns revealed differences in cation site occupancy with the high-entropy spinel being nearly fully normal. Densification behavior was investigated and showed that fully dense ceramics could be produced by hot pressing at temperatures as low as 1375°C for all compositions. Vickers' hardness values were at least 10 GPa for all compositions. The …

Constructing A Fine Dispersion And Chemical Interface Based On An Electrostatic Self-Assembly And Aqueous Phase Compound In Go/Sio2/Sbr Composites To Achieve High-Wear Resistance In Eco-Friendly Green Tires, Rui Zhang, Jiaye Li, Stephen Jerrams, Shui Hu, Shipeng Wen, Ligun Zhang

Articles

The hazard to the ecosystem caused by rubber microparticles generated from tire abrasion has been a constant concern. Therefore, to protect this ecosystem, the development of a tire tread with high abrasion resistance is especially significant. Herein, γ-aminopropyltriethoxysilane (APTES) was used to modify graphene oxide (GO) and silica (SiO2) to obtain GO and SiO2 with positive charges (NG and NS). Furthermore, NG and NS were electrostatically self-assembled by using maleic anhydride (MAH) hydrolysis, thereby obtaining composite particles (NG-NS) with “bridged structures”. Also, the NG-NS/styrene butadiene rubber (SBR) compounds possessing fine dispersion of NG-NS were prepared by the aqueous compounding method. …