Engineering Commons^™

Effects Of Elevated Temperature On The Physical Aging Of A High Temperature Thermoplastic Resin And Composite, Mark Feldman

Mechanical & Aerospace Engineering Theses & Dissertations

Development of a High Speed Civil Transport is considered by the commercial aviation industry to be one of the next big challenges for our national aircraft industry. Critical to the success of this aircraft is the development of advanced polymeric composites for both the primary and secondary structures and the predictive methodology necessary for assessment of long term durability. While polymeric composites offer an excellent strength to weight ratio a key disadvantage is the time dependent properties exhibited by the polymer matrix which can age and ultimately effect the resultant stiffness of a laminate.

Experimental studies were performed to determine …

An Investigation Of The Influence Of Tightening Torque And Sea Water On Pultruded Gfrp Composite Bolted Joints, Satish Devara

Mechanical & Aerospace Engineering Theses & Dissertations

Pultruded glass fiber-reinforced polymeric matrix composites are candidate materials for ever-increasing structural applications due to their continuous production capability, light weight and excellent properties. In this investigation an extensive experimental study has been carried out to understand their structure, basic mechanical properties, and influence of fiber orientation on the unnotched, notched and pin-loaded tensile strength. Furthermore, the effects of sea water and tightening torque separately and together on the failure loads and failure modes of the bolted joints are also studied. It is shown that blockshear failure mode is also a principal mode of failure in the bolted joints of …

Method For Producing Powder From Polycrystalline Inorganic Material, Surendra K. Kawatra, Timothy C. Eisele

Michigan Tech Patents

A method for producing powder from polycrystalline inorganic material by contacting polycrystalline inorganic material with the vapor of one or more reduced alkali metals in an environment substantially free of oxygen for a period of time sufficient to cause disintegration of the polycrystalline inorganic material into powder. The polycrystalline inorganic material may consist of one or more oxides, sulfides, or silicates, or combinations thereof. The poly crystalline inorganic material may also comprise a rock or mineral, such as basalt or pyrite.

Anion Induced Blue To Purple Transition In Bacteriorhodopsin, Mrunalini Pattarkine, Anil K. Singh

Faculty Works

Purple membrane (PM, λ" role="presentation">λmax" role="presentation">max 570 nm) of H. halobium on treatment with sulphuric acid changes its colour to blue (λ" role="presentation">λmax" role="presentation">max 608 nm). The purple chromophore can be regenerated from the blue chromophore by exogeneous addition of anions such as CI−" role="presentation">− and HPO42−" role="presentation">2−4. Chloride ion is found to be more effective than the dibasic phosphate ion in regenerating the purple chromophore. Nevertheless, one thing common to the anion regeneration is that both CI−" role="presentation">− and HPO42−" role="presentation">2−4 show marked pH effect. At pH 1.0 the efficiency of …

Design Of Gradient Index Optical Thin Films, Jeffrey J. Druessel

Theses and Dissertations

Gradient index thin films provide greater flexibility for the design of optical coatings than the more conventional 'layer' films. In addition, gradient index films have higher damage thresholds and better adhesion properties. This dissertation presents an enhancement to the existing inverse Fourier transform gradient index design method, and develops a new optimal design method for gradient index films using a generalized Fourier series approach. The inverse Fourier transform method is modified to include use of the phase of the index profile as a variable in rugate filter design. Use of an optimal phase function in Fourier-based filter designs reduces the …

Status Of The Research And Development For Fuel Cell Technology Abroad, Naichao Li, Baolian Yi

Journal of Electrochemistry

Status of the research and development for fuel cell technology abroad was overviewed, and at the aim of accelerating the research and development for fuel cell technology in China, the corresponding stategy for our country was recommended.

In Situ Studies Of Copper Electrodepostion On Hopg By Using Ecstm, Zhaoxiong Xie, Bingwei Mao, Xiangdong Zhuo, Jiqian Mu, Zhaowu Tian

Journal of Electrochemistry

In this paper, copper electrodepostion on HOPG had been in situ studied by using a homebuilt electrochemical scanning tunneling microscopy (ECSTM). Three dimensional nucleation and subsequent growth of copper crystals were found as the initial stage of copper deposition on HOPG. In the case of lower overpotential or lower concentration of Cu²⁺ , the bulk deposited copper layer tended to form smooth terraces, and grow at the edge of steps. The terraces were stable to some extent, which made it possible to be observed with atomic resolution. At a higher overpotential, the crystal size of copper were somehow smaller. …

Problems On The Study Of Anodic Films On Pb In Sulfuric Acid Solution (Ⅱ), Houtian Liu, Qunzhou Wang, Yongqin Wan, Weifang Zhou

Journal of Electrochemistry

The conditions for the growth of the different phases in the anodic Pb(Ⅱ) film on Pb in sulfuric acid solution were discussed.

A Study Of The Electroplated Fe-Cr-Ni Alloy Microstructure, Donglin Li, Jianping Liu, Fangzhou Guo, Jianrong Hua

Journal of Electrochemistry

The microstructure of the electroplated Fe-Cr-Ni alloys from the mixed carboxylic acid solution containing Cr(Ⅲ) and additives were determined with XRD and SEM. Experimental results showed that, under the experimental condition, the phase component, structure of Cu base electroplated Fe-Cr-Ni alloys had a critical thickness, which was 11 μm and a critical Ni content, which was 32%. Organic additives, formic acid or polyethylene Glycol, mainly affected the surface, cross section morphology of the electroplated Fe-Cr-Ni alloys. Adding Mo to the electroplated Fe-Cr-Ni alloys led to remarkable corrosion resistance in concentrated HCl.

The Applications Of Poap Ni2+ Films Modified Electrode As Sensor For Alcohol, Bingzeng Hua, Wenyun Hu, Yanzhen Chen

Journal of Electrochemistry

POAP Ni²⁺ films modified electrode can electrocatalyzes significantly the oxidation of alcohol. The modified electrode can be used as the electrochemical sensor for the detection of alcohol. But the oxidation of alcohol is effected by the thickness of films、the concentration of nickel ion in films, pH of electrolyte, as well as temperative. All of those conditions have been studied in order to achieve stable response current during the oxidation of alcohol, and the relation between concentration and current has been made. At last the major characteristic parameters, such as the low limitation of concentration, the response time, the ability …

Surface Raman Spectra Of Pyridine And 2 Mercaptopyrimidine Adsorbed On Rough Nickel Electrode, Qunjian Huang, Jinsong Gao, Xiongwei Cai, Bingwei Mao, Mingsen Zheng, Zhongqun Tian

Journal of Electrochemistry

The Raman spectra of pyridine and 2-mercaptopyrimidine (2-MP) adsorbed on bare nickel electrodes roughened by a HNO₃ etching procedure have been obtained for the first time by utilizing a highly sensitive confocal Raman microscope. Their adsorption behaviours are discussed briefly. This primary result illustrates a great potential for in-situ Raman spectroscopy in the study of chemical and electrochemical processes of transition metal surfaces.

Electrocatalytic Oxidation Of Some C2 Compounds (Alcohols, Aldehydes, And Carboxylic Acids) On A Pt/SbAd Electrod, Hong Li, Lincai Jiang, Xiong Jiang

Journal of Electrochemistry

The electrocatalytic oxidation behavior of some C₂ compounds(alcohols, aldehydes and carboxylic acids) on a Pt/Sb_ad electrode prepared in-situ or ex-situ UPD was investigated using pontential sweep and rotating disc electrode methods. It is confirmed that Pt/Sb_ad electrode show the most electrocatalytical active to the oxidation of aldehyde functional group and only a little activity to the oxidation of hydroxyl group, but no activity for the oxidation of carboxyl group.

The experimental results show that the activity of the Pt/Sb_ad electrode prepared by ex-situ UPD is higher than that prepared by in-situ UPD.

The limitations of the …

Studies Of Surface Treatment Methods And Their Operating Mechanisms For Activation Of Hydrogen Storage Electrode, Ronghui Hu, Hanxi Yang, Shigang Lu, Shengxian Li, Jingcheng Liu, Chongzhi Yang

Journal of Electrochemistry

Surface treatment methods by use of charge discharge cycling, KBH₄ reduction and KOH etching were parallely investigated for the rapid activation of Mn(NiCoMnAl)₅ electrode. It is found that the MH electrode treated with hot and concentrated KOH solution exhibits rapid and full activation, and also gives lower discharge overvoltage, higher stable capacity and improved cycleability. It is also revealed from SEM, EDAX and ICP analysis that the KOH activation of the electrode proceeds mainly through the enrichment of mischmetal and nickel in surface to form electrocatalytically active surface for hydrogen absorption reaction, but the surface modification with KBH …

Electrocatalytic Reduction Of Nitrite In The Presence Of Complex Of Cobalt(Ⅱ) And 1,10 Phenanthroline, Jian Tong, Xiaojun Dang, Hulin Li

Journal of Electrochemistry

The electrochemistry of cobalt(Ⅱ)-1,10-phenanthroline Co(Phen)₂²⁺ complex and its ability to electrocatalyze the reduction of nitrite were studied, we found that this complex could act as a catalyst in alkaline or neutral solution for nitrite reduction. We have investigated the effect of the complex composition on electrocatalytic ability. The effects of pH value, complex concentration, regeneration and activation of electrocatalyst on the catalytic current have been studied and discussed.

Study On Electrode Constructure And Electrical Performance Of Na/S Cell, Jianhua Yang, Jiadi Cao

Journal of Electrochemistry

A sodium wick for sodium electrode and trough shaped performs for sulfur electrode in Na/S cell were designed and investigated. The experiments suggested that the sodium wick for sodium electrode not only improved the discharge performance of cell but also reduced the quantity of sodium utilization, and increased the specific energy of Na/S cell. The trough shaped preform with alumina fibres for sulfur electrode decreased the polarization, improved the charge acceptance and prolonged the life of cell.

The Reduction Of Oxygen To Hydrogen Peroxide In An Acidic Trickle Bed Cell Using Graphite Chip Cathode, Zhaoe Lu, Guanyong Zhang, Tiangeng Zhong, Guonu Fang

Journal of Electrochemistry

The authors investigated the electrochemical reduction of oxygen to hydrogen peroxide in 0.05 mol/L H₂SO₄ solution by the trickle bed electrode using graphite chip. The bed dimension was 14×5×0.6 cm. The current efficiency and the concentration of H₂O₂ in the catholyte were determined at various current strengths and various rates of adding the electrolyte. The proper current was 0.15 A. i.e. the current density was 2.1 mA/cm² vertical cross section area of the bed. The concentration of H₂O₂ reached 7×10^-3 mol/L with the current efficiency of 0.2. If the …

Macrosegregation During Dendritic Arrayed Growth Of Hypoeutectic Pb-Sn Alloys: Influence Of Primary Arm Spacing And Mushy Zone Length, Surendra N. Tewari, Rajesh Shah

Chemical & Biomedical Engineering Faculty Publications

Thermosolutal convection in the dendritic mushy zone occurs during directional solidification of hypoeutectic lead tin alloys in a positive thermal gradient, with the melt on the top and the solid below. This results in macrosegregation along the length of the solidified samples. The extent of macrosegregation increases with increasing primary dendrite spacings for constant mushy zone length. For constant primary spacings, the macrosegregation increases with decreasing mushy zone length. Presence of convection reduces the primary dendrite spacings. However, convection in the interdendritic melt has significantly more influence on the spacings as compared with that in the overlying melt, which is …

Convection During Thermally Unstable Solidification Of Pb-Sn In A Magnetic Field, Hui Song, Surendra N. Tewari, H. C. Degroh Iii

Chemical & Biomedical Engineering Faculty Publications

Convection and macrosegregation in directionally solidified hypoeutectic Pb-38 wt pct Sn and hypereutectic Pb-64.5 wt pct Sn have been examined during upward and downward growth. Temperature fluctuations are observed along the length of the melt column during downward growth. With increasing Rayleigh number, these fluctuations change from none, to cyclic, to time periodic having multiple harmonics, and finally to random. At the higher convective driving force of 350 K temperature inversion, the transverse magnetic field decreased convective levels, strong random temperature fluctuations (flows) becoming smaller and periodic. The maximum field of 0.45 T was unable to completely eliminate convection. For …

Time Dependence Of Tip Morphology During Cellular Dendritic Arrayed Growth, Hui Song, Surendra N. Tewari

Chemical & Biomedical Engineering Faculty Publications

Succinonitrile-1.9 wt pct acetone has been directionally solidified in 0.7 X 0.7-cm-square cross section pyrex ampoules in order to observe the cell/dendrite tip morphologies, not influenced by the ''wall effects,'' which are present during growth in the generally used thin (about 200 mu m) crucibles. The tips do not maintain a steady-state shape, as is generally assumed. Instead, they fluctuate within a shape envelope. The extent of fluctuation increases with decreasing growth speed, as the micro structure changes from the dendritic to cellular. The influence of natural convection has been examined by comparing these morphologies with those grown, without convection, …

A Comparison Of Tool Life Of Two Coated Carbide Inserts Under Identical Conditions And At Different Cycle Times, Garold Zander

Graduate Research Papers

Coated hardmetals have brought tremendous increases in productivity since 1969, when they were first applied to cutting materials. These coatings are extremely hard and are very abrasion resistant. Typical coatings are alumina oxide, silicon nitride with metal oxides, titanium carbonnitrides with metal carbides, titanium nitride, titanium carbonitride, and zirconium oxide. This study examined two different coated cutting inserts to determine which would maximize performance for lathe operators.

The two chemical vapor deposition (CVD) coated indexible inserts examined were Carboloy CMNA 543 TP 100, and Carboloy CNMA 543 TP 10. Both cutting inserts were multi-coated with alumina (Al2O3 ), titanium nitride …

Structural Damage Identification From Limited Measurement Data, Richard G. Cobb

Theses and Dissertations

The research focused on the development of a new method to identify damaged structural elements from a large flexible space structure on-orbit, using limited measured modal data. Limited measured modal data is loosely defined as measured data containing only a few modal frequencies and less than 10% of the total structural degrees-of-freedom. This effort was decomposed into four specific tasks. The first is the identification of partial modal properties from measured data of the nominal space structure. Second, the finite element model must be adjusted to match the measured nominal partial data. The third task is an analysis of the …

Electrochemical Ploymerization Of Aniline In The Alkaline Solution And Properties Of Polymer, Shaolin Mu, Jinqing Kan, Aiguang Zhang

Journal of Electrochemistry

A deep yellow polyaniline was formed at the anodic electrode during electrochemical oxidation of aniline in the alkaline solution. The peak of oxidation potential for aniline in the alkaline solution was 0.7 V (vs.Ag/AgCl with a saturated KCl solution), which is about 0.3V less than that in the acidic solution. The results from rotating ring-disk electrode experiment show that two soluble intermediates were generated during electrochemical oxidation of aniline. The colour of the polymer in the alkaline solution is independent of applied potential and pH values. An adsorption peak was observed in the UV region at 500 nm for the …

Determination Of Transport Number Of The Modified Liclo4-(Peo)20 Polymer Electrolyte, Ruqi Zhou, Qngguo Liu, Weihua Qiu, Yun Zhang, Yuee Zhao, Leiling Yang

Journal of Electrochemistry

In this work a combination method of A.C. Impedance and chronoamperometry was used to determine the lithium ion transport number of LiClO₄·(PEO)₂₀·(PC)₁₂·(EC)₁₂ polymer electrolyte. It is known that lithium is thermodynamically unstable in non-aqueous or polymer electrolytes, leading to the formtion of a film on lithium surface, called as solid electrolyte interphase (SEI). The presence of SEI layer will greatly influence the experimental result of lithium ion transport number. The new method avoid the effect of SEI layer, and can give correct transport number of lithium ion in the electrolyte of DCIO_{4 …}

The Inhibition Of Amphipathic S- And N-Containing Compounds On Carbon Steel Corrosion, Wei Xing, Yibin Shan, Du Guo, Tianhog Lu, Shiquan Xi

Journal of Electrochemistry

Ordered monolayers of S- and N-containing amphipathic corrosion inhibitors were depoitod onto the surfaces of carbon steel electrode with super-molecular assembly technique. The effect of molecular aggregation of monolayers on carbon steel corrosion in 0.05 mol·cm^-3 H₂SO₄ and the mechanisms of these inhibitors were discussed in details. It was found that the transport of hydrated hydrogen ion to the surface of steel depends strongly on the inhibitor molecular aggregation in the monolayers.

Development Of The High Capacity Sintered Type Nickel Positive Electrode, Guohua Yu, Shijie Zhang, Xiaolin Wang, Jingqi Wei

Journal of Electrochemistry

By improving the design and technologies of the sintered type nickel oxide positive electrode for the NiMH batteries, We do our best to increase the sinter volume and porosity,the amount of the active materals and their utilization, so we have fabricated the high capacity sintered typo nickel electrodes fitting for the NiMH battreies. The sfecitic capacity of the lot produced electrodes is up to 550 mA/cm^-3.

The Influence Of Cathode Ingredients In Zinc Chloride Type Battery On The Discharge Ability, Qi Shen, Biao Zhuang

Journal of Electrochemistry

The influence of cathodic powder ingredients in ZnCl₂ type heavy duty battery on the discharge ability has been studied, a suitable battery ingredients is founds.

Ftis Observation Of Twin Adsorbates Of Co On Rh Electrode In Acid Solution, Wenfeng Lin, Shigang Sun

Journal of Electrochemistry

Because of its great importance both in electrocatalysis and C1 chemistry applications, the adsorption of CO on metallic electrodes such as Pt, Pd, Au, Ag, RhF, etc. has been extensively studied by in situ infrared spectroscopy Since 1981. In all these studies only three types of CO adsorbates, i. e., linear (2090～2000 cm^-1), bridgrd (2000～1900 cm^-1) or multi-bonded (1900～1800 cm^-1) species, were identified. A different absorbate, twin CO on rhodium (Rh(CO)₂), does exist on the solid/gas interface of highly dispersed Rh or Rhn clusters on supports, this species originating a doublet at …

Hydrogen Evolution Reaction On Nanocrystalline Co-Mo/Ni Composite-Coated Electrodes, Weizeng Yu, Jie Ma, Yiming Chu, Huizhe Zhu, Hongjie Wang, Shuncheng Liu

Journal of Electrochemistry

The electrochemical behaviours of the hydrogen evolution reaction (HER) at electrodes prepared by composite coating of nanocrytstalline Co-Mo alloy particles formed by ball milling on nickel base has been sludied by using sleady-state polarization and ac impedance techiu ques. The microstructure and the size of the nanocrystals of Co-Mo alloy and the morphology of the composite-coating surface of the electrodes are measured by XRD, TEM and SEM. Results show that the nanocrystalline Co-Mo alloys prepared by high energy ball milling has high electrocatalytic activity for HER. The electrocatalytic activity for the HER is enhanced and the energy of activation for …

Electrochemical Studies On Corroding Metallic Electrodes In Frequency Domain, Chunan Cao

Journal of Electrochemistry

The electrochemical studies on corroding metallic electrodes carried out in the State Key Laberatory for Corrosion and Protection are reviewed briefly: (1) General equations of faradaic admittance under potential-control condition were derived based on the stabillity conditions of steady processes. The faradaic admittance at mixed potential then was deduced based on these equations and the electrochemical impedance spectroscopy (EIS) at corrosion potentials in the solutions containing interface inhibitors was diseussed by application of the thecetical results obtained. (2) The spectral power density (SPD) curves for electrochemical noise (EN) during the initial stagu of pitting corrosion were observed for iron and …

An Indirect Electrochemical Oxidation Of Toluene─Catalytic Effects Of Ag(Ⅰ) On Mn(Ⅱ)/Mn(Ⅲ) Couple Transition At Pt Electrode, Zhonghua Wang, Yunan Qu, Xingguo Yan, Qngmin Hua, Guacai Chen, Zhongquan Wang

Journal of Electrochemistry

The Catalytic effects of Ag(Ⅰ) on toluene oxidation by Mn(Ⅲ) as well as the anodic generation of Mn(Ⅲ) were investigated. The rates of toluene oxidation were first order with respect to both Ag(Ⅰ) and Mn(Ⅲ). Ag(Ⅱ) formed on the surface of the platinum anode when Ag(Ⅰ) was present in the anolyte, which catalyic the Mn(Ⅱ) to Mn(Ⅲ) in solution.