Engineering Commons^™

Oxidation Kinetics Of Silver Thin Films For Antimicrobial Applications In The Health Care Industry, Sean D. Morham

Materials Engineering

To determine if varying city water qualities from around the United States can support a developing “oxidation corrosion of silver thin films” method of creating aqueous ionic silver solutions for the anti-microbial treatment of healthcare linens, a test was devised holding all variables constant with the exception of water quality parameters. This corrosion style test was done in order to assess a pass/fail criteria of 25 ppb ionic silver concentration in the aqueous solutions which resulted from the corrosion of silver thin film coated substrates. Above 25 ppb being a pass, below 25 ppb being a fail. While varying the …

Investigating The Mechanical Properties Of Compression Molded Carbon Fiber Reinforced Sheet Molding Compound, Bradley A. Jones

Materials Engineering

Callaway Golf receives a proprietary blend of prepreg material from Quantum Composites. Callaway processes the prepreg in-house and supplied 254mm x 254mm x 1.3mm panels of carbon fiber sheet molding compound (CFSMC) for characterizing. Tensile strength was analyzed by conducting tensile tests per ASTM D3039. Tensile coupons were cut to 254mm long by 25.4mm wide. Tabs were constructed from 1.6mm thick GFRP printed circuit board material. A commercial grade two part epoxy was used to bond the tabs to the CFSMC. Tensile results were inconclusive due to consistent fractures occurring outside the gauge lengths of the specimens.

Flexure strength was …

A Rheological Model Of The Dynamic Behaviour Of Magnetorheological Elastomers, Lin Chen, Stephen Jerrams

Articles

A rheological model is described that was developed to simulate the dynamic behaviour of magnetorheological elastomers (MREs). The viscoelasticity of the polymer composite, magnetic field induced properties and interfacial slippage between the matrix and particles were modelled by analogy with a standard linear solid model, a stiffness variable spring and a spring-Coulomb friction slider respectively. The loading history and rate dependent constitutive relationships for MREs were derived from the rheological model. The hysteresis loop from shear strain - shear stress plots, which determines the shear modulus and loss factor, were obtained from substituting cyclic loading into these constitutive relationships. The …

A Study Of Three Transition Metal Compounds And Their Applications, Zhen Qin

Dissertations

The La_5/8-yPr_yCa_3/8MnO₃ with colossal magnetoresistance (CMR) effect has a rich phase diagram and is well studied for its electronic phase separation phenomenon, where the ferromagnetic (FM) metal order co-exists and competes with the charge-ordered (CO) insulator phase. High Pr doping will favor the CO order, leading a sharp FM to CO dominated phase transition around Pr concentration of 0.3 and above. Hydrostatic pressure favors FM metallic order without damaging the sample and can be tuned continuously. In this study, pressurized-magnetic and resistivity measurements was done on a La_0.25Pr_0.375Ca_{0.375 …}

Synthesis And Catalytic Property Of Flaked Spindle-Like Cuo Nanocrystals, Jian-Feng Fan, Li-Qing Li, Yu-Feng Huang, Lou-Zhen Fan

Journal of Electrochemistry

A simple and efficient electrochemical route was developed for the synthesis of flaked spindle-like CuO nanocrystals using aqueous electrolyte and Cu sacrificial anode (graphite as the cathode) in an undivided cell at a constant potential mode under room temperature. The morphologies, structure and component of CuO nanocrystals obtained were characterized by SEM, XRD, respectively. Flaked spindle-like CuO nanocrystals were successfully used to modify a GC electrode to detect H₂O₂ with cyclic voltammetry (CV) and amperometric (AC).The results showed that products were pure monoclinic CuO nanocrystals. The linear range for the determination of hydrogen peroxide is from 1.0 …

Detection Of Acute Promyelocytic Leukemia Pml/Rarî± Fusion Gene Using Graphene Modified Glassy Carbon Electrode, Zhi-Xian Lian, Guang-Xian Zhong, Kun Wang, Ai-Lin Liu, Xin-Hua Lin, Yuan-Zhong Chen

Journal of Electrochemistry

A graphene modified glassy carbon electrode (GCE) was prepared by electrochemical reduction of graphite oxide fixed on the surface of GCE. Then, the amino-group modified probe of acute promyelocytic leukemia (APL) PML/RARα fusion gene fragment was immobilized onto surface of the graphene modified GCE by coupling activating agent. With methylene blue (MB) as a novel electrochemical indicator, artificial APL PML/RARα fusion gene fragment was measured by differential pulse voltammetry (DPV). The result indicated graphene nanomaterial showed good sensitization on the signal of MB. The relationship between the reduction peak current of MB and the concentration of complementary strand was linear …

Influence Of Tert-Butylpyridine On The Band Energetics Of Nanostructured Tio2 Electrodes And The Photoelectrochemical Properties Of Dye-Seneitized Electrodes, Shu-Ming Yang, Ji-Chao Wang, Hui-Zhi Kou, Hong-Bin Xue, Hong-Jun Wang, Yu-Ling Guo

Journal of Electrochemistry

The flat band edges (Efb) of nanostructured TiO₂ electrodes in electrolyte solutions with tert-butylpyridine (TBP) of different concentrations have been determined with spectroelectrochemical technique. TBP played a role in band energetics of nanostructured TiO₂ electrodes. The Efb values of -2.25, -2.46 and -2.62 V were determined in three 0.2 mol•L^-1 tetrabutylammonium perchlorate (TBAP) acetonitrile electrolytes which contain 0, 0.2 and 0.4 mol•L^-1 TBP respectively. The addition of Li+ ions shifted Efb positively. The Efb values of -1.12, -1.22 and -1.30 V were determined in three 0.2 mol•L^-1 LiClO₄ acetonitrile electrolytes which contain 0, 0.2 …

Effects Of Additives On The Electrochemical Behaviors Of Zn Electrode In Alkaline Solutions, Shu-Na Hong, Hai-Bin Lin, Zuo-Jian Su, He-Bing Zhou, Man Liang, Wei-Shan Li

Journal of Electrochemistry

Electrochemical behaviors of Zn in 3mol⋅L^-1 KOH solution containing the single additive(Pb(NO₃)₂, SDBS) the mixed additives(Pb(NO₃)²⁺SDBS) were investigated. The results showed that all the additives can supress the corrosion of zinc in 3mol•L_^-1 KOH solution. And the inhibition effeciency of the mixed additives is higher than that of any single additive.

Preparation And Electrocatalytic Activity Of The Pt/Wc/Tio2 Composites, Chun-An Ma, Bin Yu, Mei-Qin Shi, Xiao-Ling Lang

Journal of Electrochemistry

TiO₂ was used as the support for preparation of Pt/WC/TiO₂ composite catalyst. The composites were characterized by XRD, SEM and TEM methods. The electrocatalytical activity of Pt/WC/TiO₂ composite for oxidation of methanol was investigated by cyclic voltammetry. Pt/WC/TiO₂ exhibited higher activity compared with that of Pt/TiO₂ and Pt/WC composite catalysts. Based on this we discussed the effects of crystal phases of TiO₂ on the electrocatalytical activity of Pt/WC/TiO₂ composite catalyst.

Dft Study Of Co2 Reduction To Hydrocarbons On Cu Surfaces, Li-Hui Ou, Sheng-Li Chen

Journal of Electrochemistry

CO₂ reduction on Cu(111) single crystal surfaces was studied using DFT calculations on the reaction energies and the minimum energy paths. The results indicated that the possible reaction paths for CO₂ reduction on Cu(111) surface are CO₂(g) + H* → COOH* → (CO +OH)*, (CO + H)* → CHO*, CHO + H → CH₂O* → (CH_2⁺O)*, CH₂* + 2H* → CH₄ or 2CH₂* → C₂H₄. On Cu(111) surface, the reaction rate is controlled by steps of CH₂O* → (CH_{2 …}

Capacitance Behaviors Of Ti/Ru0.1Ti0.1Sn0.8O2 Electrodes, Hai-Yan Chen, Yan-Qun Shao, Dian Tang

Journal of Electrochemistry

Ti/Ru_0.1Ti_0.1Sn_0.8O₂ electrodes were prepared by low temperature thermal decomposition. The structural characteristics were analyzed by X-ray diffraction(XRD).The performances were tested by cyclic voltammetry and constant current charge-discharge measurements. The results show that, the structure of Ti/Ru_0.1Ti_0.1Sn_0.8O₂ belongs to small rutile phase. A high specific capacitance of 933F/g is obtained at scan rate of 20 mV/s. The cycle life test shows a 23.6% specific capacitance lost after 1000 cycles. The electrode has a good cycle stability and reversibility.

The Flip-Flop Behavior Of Acetonitrile At Au Electrode Surface Investigated By Sum Frequency Generation Vibrational Spectroscopy, Zhi Huang, Xin Tang, Gang-Hua Deng, En-Cai Zhou, Hong-Fei Wang, Yuan Guo

Journal of Electrochemistry

The electrochemical interface between liquid acetonitrile and polycrystal gold electrode is investigated by in situ infrared visible sum frequency generation spectroscopy (SFG-VS). The structure of acetonitrile adsorbed at polycrystal gold electrode surface is studied as a function of electrode potential. The SFG spectra of CH₃ group indicate acetonitrile orients in response to the electrode potential. The SFG signal of CH₃ group turns lower as the electrode potential changes from -700mV to 300mV, and vanishes around the 300mV(pzc), then becomes a negative signal above 500mV, which indicates that the orientation is predominately with the CH₃ group toward the …

Research Progress In Orthosilicates As Cathode Materials For Li-Ion Batteries, Dong-Ping Lv, Lin Wang, Yong Yang

Journal of Electrochemistry

Rechargeable Li-ion batteries fulfilling high-energy density, high safety, environmental friendliness, and low cost are demanded urgently for energy storage systems. Besides the structure stability arising from the strong Si-O covalent bond, environmental benignancy and low cost from the characteristics of Fe, Mn, Si elementals, orthosilicates (Li₂MSiO₄) show promising prospect to meet the demand of high-energy density for its two available Li+ per formula unit. Motivated by these significant advantages, Li₂MSiO₄ have been intensively investigated in the past few years. In the present work, we gave a review on the progress of orthosilicate research …

Effect Of Pore Size On Pseudo-Capacitive Performance Of Nio In The Mixed Electrolyte Of Koh And Hexacyanoferrate, Wen Wu, Meng-Yan Hou, Dan-Dan Zhou, Yong-Yao Xia

Journal of Electrochemistry

In this paper, five kinds of NiO samples with different pore size distributions were synthesized .The electrochemical capacitance of the samples were characterized in 3 mol/L KOH solution with and without hexacyanoferrate addition. Electrochemical test results indicated the NiO sample with an optimum pore size of about 15 nm shows high Coulombic efficiency of the N₄(NiO) electrode as the redox reaction of hexacyanoferrate ions would be limited in the pore, thus prevent ion diffusion into the bulk electrolyte solution .

Investigation Of Supercapacitors Based On Polyvinyl Alcohol Hydrogel-Polymer Electrolyte, Kai-Qing Xu, Le-Qing Fan, Ji-Huai Wu, Qing Leng, Xin Zhong, Jian-Ming Lin, Miao-Liang Huang, Zhang Lan

Journal of Electrochemistry

For the first time, the supercapacitor based on the hydrogel-polymer electrolyte which consisted of the cross-linking of polyvinyl alcohol-glutaraldehyde (PVA-GA) using 2-acrylamido-2-methyl propane sulfonic acid (AMPS) as solicitation reagent was assembled. The gel polymer electrolyte was characterized by FTIR and AC impedance. The maximum ionic conductivity is 1.23 mS/cm at room temperature. The electrochemical properties of the supercapacitor were investigated by cyclic voltammetry, AC impedance spectra and constant current charge-discharge curve. The results show that the specific capacitance reachs 139 F/g with AMPS of 1.0 g and 0.05 mL of 5 %(by mass) GA. And the specific capacitance still retained …

Study On Direct Electro-Oxidation Of Anisaldehyde, Lin-Lin Wu, Ying-Hong Zhu, Shan-Shan Li, Hong-Yan Zeng, Chun-An Ma

Journal of Electrochemistry

The oxidation of anisole on Pt electrode was investigated by cyclic voltammery and constant potential electrolysis. The influence of scan rates, substrate concentration, supporting electrolytes and solvent were considered . The results show that the electro-oxidation process of anisole was irreversible. In this research the sulfuric acid was the best supporting electrolytes and acetone was the best solvent, and the process was controlled by diffusion . The product of constant potential electrolysis was charactered by GC-MS .The results show that the main products was anisaldehyde, and the selectivity was up to 66.5% when using acetone as solvent.

Electric Vehicles And Power Batteries, Xin-Ping Ai, Han-Xi Yang

Journal of Electrochemistry

In retrospect of the historical development of Electric Vehicles (EV), the impact of battery technologies on the progress of EV was discussed. In consequence, it is concluded that the lack of advanced batteries was the main cause for the fluctuations of EV development and the sluggish commercialization of electric cars in the past century. After a brief introduction to the classification and the requirements of electric vehicles, the main issues of the batteries including safety, temperature range for operation and the cost as well as the effects of these factors on the applications of advanced batteries for electric vehicles were …

Comparison Of Catalytic Performance On Different Materials Supported Pd Catalysts For Formic Acid Oxidation, Su-Dong Yang, Yan-Yu Liang, Zhu-Liang Wen, Qi-Jun Song, Xiao-Gang Zhang

Journal of Electrochemistry

Graphite oxide (GO) was prepared from by Hummers method. Then the graphene nanosheets supporting Pd catalysts were prepared by a single-step chemical reduction method. The electrocatalytic performance for formic acid oxidation of the prepared Pd/graphene composite was studied as an electrode material in comparison with the composite catalysts based on the other carbons (MWCNTs, SWCNTs, and Vulcan XC-72 carbon black). X-ray diffraction (XRD) and transmission electron microscopy (TEM) measurements indicated that the Pd nanoparticles were well dispersed on the surface of the graphene nanosheets with a small particle size. The electrocatalytic oxidation of formic acid was studied by electrochemically active …

Anode Electrodeposition Of Ti/Mno2 Electrode And Electrocatalytic Oxidization Properties Of Phenol Degradation, Ye Chen, Wen-Li Zhao, Qing Wen

Journal of Electrochemistry

Ti-base manganese dioxide (Ti/MnO₂) electrode was prepared by anodically electrodeposition technology in this paper. The structure of the electrode, the microstructure of the electrode surface and the element composition of the electrode were analyzed by XRD, SEM and EDS. The preparation process parameters of the electrode were studied in detail with the help of the V~logi curve and phenol degradation curve. The Ti/MnO₂ electrode was anodically electrodeposited at current density 4mA•cm^-2, the Mn^{2 +} ions concentration 0.5mol•L^-1 and temperature70℃. The V~logi curve and phenol degradation curve were used to evaluate electrocatalytic oxidization properties …

Electrochemical Studies Of Zinc Injection Into The Structure Materials Of Nuclear Power Plants, Sheng-Han Zhang, Yu Tan, Ke-Xin Liang

Journal of Electrochemistry

The electrochemical and semiconductor characters of oxide films formed on 304L, 316L stainless steel and alloy 600 in high temperature water with zinc addition were studied. Stress corrosion cracking and occupational radiation can be retarded effectively by zinc injection to the primary circuit of pressurized water reactor (PWR). The semiconductor characters of the materials formed by zinc injection was analyzed by Mott-Schottky curves. The surface morphology and components of the corrosion oxide layer were examined and detected by scanning electron microscope (SEM) and X-ray photoelectron spectroscopy (XPS). The result reveals that the smaller crystals and the complex Zn-Cr-Ni-Fe oxide were …

Electrochemical Capacitive Performance Of Mesoporous Carbon Based Co-Ni Oxides, Zhen-Sheng Yang, Ling-Bin Kong, Li Deng, Yong-Chun Luo, Long Kang

Journal of Electrochemistry

By using defects on the surface of CMK-3 served as nucleation center, Co_0.25Ni_0.75 oxide/C composite was successfully prepared through a simple chemical co-precipitation method. Characterization was carried by using X-ray diffraction, BET and scanning electron microscopy. Results showed that a perfect mesoporous network of interconnected nanoflakes was obtained for Co_0.25Ni_0.75 oxide/C composite and, this material has a less crystallization, interconnected nanoflakes network structure and a narrow mesoporous distribution at about 3~4 nm. The highly dispersed and loosely packed Co_0.25Ni_0.75 oxide/C composite possessed good electrochemical accessibility and fast diffusion rate of OH …

Preparation And Performance Of Carbon-Coated Si/C Composites, Li-Li Du, Quan-Chao Zhuang, Tao Wei, Yong-Li Cui, Zhi Sun, Shi-Gang Sun

Journal of Electrochemistry

Si/C composite for lithium ion batteries was obtained by pyrolyzing and ball-milling. The microstructure and component of the composite was characterized by SEM and XRD, the electrochemical performance was investigated by electrochemical impedance spectroscopy (EIS), cyclic voltammetry (CV) and galvano static charge-discharge tests. The results illustrate that the particle of Si/C composite prepared by pyrolysis exhibits inerratic morphology, uniform carbon-coating layer, good electrical conductivity, low resistance. The first intercalated-lithium capacity of the composite material is 4495 mAh/g; the first coulomb efficiency is 65.3%. From the second week the coulomb efficiency maintains 97%, and the capacity at the 100th cycle can …

Complementary Metal-Oxide Semiconductor-Compatible Detector Materials With Enhanced 1550 Nm Responsivity Via Sn-Doping Of Ge/Si(100), Richard T. Beeler, Jay Mathews, Mee-Yi Ryu, Yung-Kee Yeo, Jose Menendez, John Kouvetakis

Faculty Publications

Previously developed methods used to grow Ge_1−ySn_y alloys on Si are extended to Sn concentrations in the 10¹⁹−10²⁰ cm⁻³ range. These concentrations are shown to be sufficient to engineer large increases in the responsivity of detectors operating at 1550 nm. The dopant levels of Sn are incorporated at temperatures in the 370–390 °C range, yielding atomically smooth layers devoid of threading defects at high growth rates of 15–30 nm/min. These conditions are far more compatible with complementary metal-oxide semiconductor processing than the high growth and processing temperatures required to achieve the same …

Review Of The Maxus 8 Sounding Rocket Experiment To Investigate Solidification In A Ti-Al-Nb Alloy, Robin Mooney, David Browne, Olga Budenkova, Yves R. Fautrelle, Ludo Froyen, Andrey Kartavykh, Stephan Rex, Burkhard Schmitz, Daniella Voss, Shaun Mcfadden

Conference Papers

A review of the MAXUS 8 sounding rocket microgravity experiment to investigate solidification structures in a Ti-Al-Nb intermetallic alloy is presented. The experiment was part of the Intermetallic Materials Processing in Relation to Earth and Space Solidification (IMPRESS) EU FP6 project. Key objectives were to investigate columnar and equiaxed solidification, and to achieve Columnar-to-Equiaxed Transition (CET) in the alloy. A microgravity experiment was designed to achieve this using a controlled power-down method. Two alloys were tested: one inoculated with a grain refiner and the other without grain refinement. Unrefined samples displayed axial and radial columnar growth. Boride inoculated samples displayed …

Characterization And Implementation Of Low Intensity Pulsed Ultrasound As A Tool To Apply Physical Load To Scaffolds And Bone Cells For Fracture Repair, Scott Frazee

Master's Theses

One current challenge in treating bone fractures is the effective treatment of non-unions and delayed unions. Low Intensity Pulsed Ultrasound (LIPUS) has been approved by the FDA to treat fresh fractures since 1994 and non-unions since 2000 and is an attractive treatment option because it is non-invasive. The mechanism by which it works, however, is not well understood; what is known is largely confined to the resultant changes in chemical output of cells. In this thesis several concepts and techniques were brought together to investigate the following hypothesis: LIPUS produces a measurable physical load that results in measurable deformation and …

Plasmonic Effect On The Photoluminescence Of Inas Quantum Dot Nanostructures, David Fryauf

Electrical Engineering Undergraduate Honors Theses

New materials for thin film photovoltaic applications are being explored worldwide, and one of the most popular new implementations is the introduction of an intermediate band gap in the semiconductor energy structure. Careful manipulation of semiconductor lattice material can form nanostructures such as quantum dots, which can be tuned to control specific intermediate energy levels. The introduction of an intermediate band in photovoltaic devices has a theoretical potential sunlight-toelectricity efficiency of roughly 63%. However, a specific material challenge of these thin film devices is limited absorption of long wavelengths of light. To increase absorption of the sun's visible spectrum, plasmonic …

Influence Of Material Selection And Fabrication Process Repeatability On Mechanical Properties Of Glass-Polymer Matrix Composite Structures, Charles Edwards

All Theses

This study has aimed to evaluate property uniformity from data obtained utilizing one design of a single layup composite plaque, three sources of glass fibers and a single, industry accepted resin to produce a repeatable fabrication process. This thesis has investigated the following:
1. Whether the type of glass (E-Glass, S-Glass, and R-Glass) influences the property values of individually tested samples compared between glass types.
2. Whether the type of glass influences the property uniformity throughout the set of tested samples.
3. Whether the composite plaque design and resulting performance, as defined by ASTM Standards or industry accepted parameters, is …

Mechanical Properties Of Pecvd Boron Carbide, Dhairyashil Aher

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

To the best of our knowledge, the mechanical properties of PECVD boron carbide (BC) grown using ortho-carborane as a source molecule have never been investigated before. Therefore, this thesis is an attempt to apply the bulge test and the nanoindentation technique for the mechanical characterization of PECVD BC thin films. Mechanical properties such as the Young’s modulus, hardness and residual stress were investigated. The bulge test system using an interferometry technique to measure the deflection of membrane has been designed. Commercially available LPCVD SiN_x membrane windows were used as a substrate to deposit BC films for the bulge test. …

An Evaluation Of The Performance Characteristics Of Olivine Temper In Pueblo Ii Virgin River Puebloan Ceramics, Sharlyn Anderson

UNLV Theses, Dissertations, Professional Papers, and Capstones

The purpose of this study is to examine the technological properties of the three dominant temper types - olivine, sand, and sherd - used by the Virgin Branch Puebloan during the Pueblo II era (AD 1000-1500) to explain the high proportion of Moapa Gray Ware traded to the Moapa Valley at that time. The research is guided by the hypothesis that olivine tempered pottery - or Moapa Gray Ware - possessed superior technological qualities than locally made wares, and that these qualities fueled the demand of Moapa Gray Ware ceramics.

This thesis evaluates one possibility for explaining the transportation of …

Peripheral Soldering Of Flip Chip Joints On Passive Rfid Tags, Md Syful Islam

UNLV Theses, Dissertations, Professional Papers, and Capstones

Flip chip is the main component of a RFID tag. It is used in billions each year in electronic packaging industries because of its small size, high performance and reliability as well as low cost. They are used in microprocessors, cell phones, watches and automobiles. RFID tags are applied to or incorporated into a product, animal, or person for identification and tracking using radio waves. Some tags can be read from several meters away or even beyond the line of sight of the reader. Passive RFID tags are the most common type in use that employ external power source to …