Engineering Commons^™

Giant Magnetostriction In Annealed Co1-XFeX Thin-Films, Dwight Hunter, Will Osborn, Ke Wang, Nataliya Kazantseva, Jason R. Hattrick-Simpers, Richard Suchoski, Ryota Takahashi, Marcus L. Young, Apurva Mehta, Leonid A. Bendersky, Same E. Lofland, Manfred Wuttig, Ichiro Takeuchi

Faculty Publications

Chemical and structural heterogeneity and the resulting interaction of coexisting phases can lead to extraordinary behaviours in oxides, as observed in piezoelectric materials at morphotropic phase boundaries and relaxor ferroelectrics. However, such phenomena are rare in metallic alloys. Here we show that, by tuning the presence of structural heterogeneity in textured Co_1−xFe_x thin films, effective magnetostriction λeff as large as 260 p.p.m. can be achieved at low-saturation field of ~10 mT. Assuming λ100 is the dominant component, this number translates to an upper limit of magnetostriction ofλ100≈5λeff >1,000 p.p.m. Microstructural analyses …

Effect On The Processing Characteristics Of Zno Varistors Produced Using Vibratory Milling, Maura Kelleher, M.S.J. Hashmi

Conference Papers

Abstract. Each manufacturing stage in the production of zinc oxide varistors from powder preparation to the final encapsulated device is important not only for the formation of the varistor component with optimum microstructure and thus electrical characteristics but also for avoiding the introduction of flaws and reduced yield. In this paper the authors describe and discuss the effect of multi-elemental oxide additives having been milled for different durations using a vibratory mill with cylindrical zirconia media on the powder characteristics of the subsequent processing stages. A commercial ZnO varistor formulation was used. The subsequent processing stages that are given particular …

Fabrication Of Size-Tunable Metallic Nanoparticles Using Plasmid Dna As A Biomolecular Reactor, Jacopo Samson, Irene Piscopo, Alex Yampolski, Patrick Nahirney, Andrea Parpas, Amit Aggarwal, Raihan Saleh, Charles Michael Drain

Publications and Research

Plasmid DNA can be used as a template to yield gold, palladium, silver, and chromium nanoparticles of different sizes based on variations in incubation time at 70 °C with gold phosphine complexes, with the acetates of silver or palladium, or chromium acetylacetonate. The employment of mild synthetic conditions, minimal procedural steps, and aqueous solvents makes this method environmentally greener and ensures general feasibility. The use of plasmids exploits the capabilities of the biotechnology industry as a source of nanoreactor materials.

Deformations Of Crystal Frameworks, Ciprian Borcea, Ileana Streinu

Computer Science: Faculty Publications

We apply our deformation theory of periodic bar-and-joint frameworks to tetrahedral crystal structures. The deformation space is investigated in detail for frameworks modelled on quartz, cristobalite and tridymite.

Introducing Porous Silicon As A Sacrificial Material To Obtain Cavities In Substrate Of Soi Wafers And A Getter Material For Mems Devices, Wajihuddin Mohammad

Doctoral Dissertations

Microelectromechanical system (MEMS) resonators have been a subject of research for more than four decades. The reason is the huge potential they possess for frequency applications. The use of a MEMS resonator as the timing element has an experimental history and huge progress has been made in this direction. Vacuum encapsulated MEMS resonators are required for high precision frequency control. Hence, a device with a high quality factor and durability is needed. In this effort, a new process for producing a cavity in the substrate of Silicon on insulator (SOI) MEMS devices and augmenting it with a getter using porous …

Simulation Of The Fluid Flow-Related Phenomena In The Electrolyte Of An Aluminum Electrolysis Cell, Yufeng Wang, Lifeng Zhang, Xiangjun Zuo

Materials Science and Engineering Faculty Research & Creative Works

A full-scale water model and mathematical simulation were used to study the fluid flow-related phenomena in a water model of an aluminum electrolysis cell. the time-dependent, multiphase fluid flow model was developed to represent the complex transient flow in the electrolysis bath. the accuracy of the mathematical model was validated by the ink dispersion and laser doppler velocimetry measurements in the water model. the shape, motion, release frequency of large-size bubbles, the fluid flow pattern, and the electrolyte-metal interface were predicted by the mathematical simulation. the design and operation of the anode were discussed, including the effect of the anode …

Creating A Uniform Magnetic Field For The Equi-Biaxial Physical Testing Of Magnetorheological Elastomers; Electromagnet Design, Development And Testing., Dave Gorman, Stephen Jerrams, Ray Ekins, Niall Murphy

Conference Papers

No abstract provided.

Distributed Spacing Stochastic Feature Selection And Its Application To Textile Classification, Jeffrey D. Clark

Theses and Dissertations

Many situations require the need to quickly and accurately locate dismounted individuals in a variety of environments. In conjunction with other dismount detection techniques, being able to detect and classify clothing (textiles) provides a more comprehensive and complete dismount characterization capability. Because textile classification depends on distinguishing between different material types, hyperspectral data, which consists of several hundred spectral channels sampled from a continuous electromagnetic spectrum, is used as a data source. However, a hyperspectral image generates vast amounts of information and can be computationally intractable to analyze. A primary means to reduce the computational complexity is to use feature …

A Modified Surface On Titanium Deposited By A Blasting Process, Caroline O' Sullivan, Peter O'Hare, Greg Byrne, Liam O'Neill, Katie B. Ryan, Abina M. Crean

Publications

Abstract

: Hydroxyapatite (HA) coating of hard tissue implants is widely employed for its biocompatible and osteoconductive properties as well as its improved mechanical properties. Plasma technology is the principal deposition process for coating HA on bioactive metals for this application. However, thermal decomposition of HA can occur during the plasma deposition process, resulting in coating variability in terms of purity, uniformity and crystallinity, which can lead to implant failure caused by aseptic loosening. In this study, CoBlast™, a novel blasting process has been used to successfully modify a titanium (V) substrate with a HA treatment using a dopant/abrasive regime. …

Evaluation Of Cathode Materials For Low Temperature (500-700c) Solid Oxide Fuel Cells, Alexander M. Lassman

Master's Theses

Solid oxide fuel cells (SOFC) have gained a great deal of interest, due to their potential for high efficiency power generation and ability to utilize hydrogen fuel, as well as various hydrocarbon-based fuels. A recent trend in SOFC development has been towards lower operating temperatures (500-700°C), which can substantially reduce the cost and complexity of the system. This thesis presents an investigation into state of the art Ba- and La- based cathode materials for use in low temperature (500-700°C) solid oxide fuel cells.

Synthesis of A-site deficient [A=0.97] Ba_0.5Sr_0.5Co_0.8Fe_0.2O₃ (BSCF) was …

A Quantitative Study Of The Weldability Of Inconel 718 Using Gleeble And Varestraint Test Methods, Sean Quigley

Master's Theses

Nickel super alloy Inconel 718 was tested and compared to Haynes 230 using Gleeble and Varestraint mechanical test methods. Hot cracking susceptibility was examined in either alloy using a sub-scale Varestraint test method at 5 augmented strain levels: 0.25%, 05.%, 1%, 2%, and 4%. Maximum crack length, total crack length, and number of cracks were measured for each strain level. Gleeble hot ductility on-heating and on-cooling tests were performed on both alloys. Inconel 718 was tested on-heating at target temperatures of 1600˚F, 2000˚F, 2100˚F, 2200˚F, and on cooling at 1600˚F, 1700˚F, 1800˚F, 1900˚F, and 2100˚F. Haynes 230 was tested on-heating …

Improved Manufacturing Methods Of Bovine Femur Samples For Ultrasonic Testing And Assessment Of Materials Through Contract Angle Measurement, Kevin Mathew Lopez Galang

Biomedical Engineering

At California Polytechnic State University of San Luis Obispo (Cal Poly), the Biomedical Engineering department (BMED) requires its students to take the course listed as “BMED 420: Principles of Biomaterial Designs.” BMED 420 has a required laboratory section every week throughout the duration of the course that is meant to be a supplemental tool for learning. During the lab sections, students perform experiments and exercises that are currently being implemented in the industry. Despite accuracy of the methods and experiments relative to their use in the industry, there is always room for improvement. The objective of this project will illustrate …

Testing, Modelling And Validation Of Numerical Model Capable Of Predicting Stress Fields Throughout Polyurethane Foam, Conor Briody, Barry Duignan, Stephen Jerrams

Conference Papers

Wheelchair seating systems are specialised for a number of reasons as users can have impaired mobility, which increases the possibility of pressure build up. These areas of high pressure frequently occur in the trunk region under the bony prominences known as the Ischial Tuberosities (IT), pressure ulcers may occur consequently. Polyurethane foam has been in use for some time in wheelchair seating systems as it exhibits good pressure relieving capabilities in most cases. However, little quantitative research has gone into foamed polymers, in comparison with conventional elastomeric materials. This lack of knowledge can ultimately lead to more time being spent …

Synthesis And Development Of Boron Nanotubes And Metal/Ceramic-Carbon Nanotube Composites, Jinwen Liu

Dissertations

The first part of this thesis will be focused on developing a facile and scalable solid — solid chemical vapor deposition (CVD) process using a solid boron precursor to synthesize crystalline boron nanotubes (BNTs) mixed with small amounts of boron nanofibers (BNFs). The synthesis involves the use of solid boron precursors - magnesium boride and magnesium borohydride, magnesium and nickel boride as co-catalysts, and porous MCM-41 zeolite as the growth template. Experimental parameters, such as temperature, grinding of constituents and starting precursor-catalyst-template compositions, were studied and optimized. Detailed characterization have been carried out using field-emission scanning electron microscopy (FE-SEM), transmission …

Study On Residual Powders Of Lithium-Ion Batteries With Different Voltages After Explosion, He Li, Zhi-Kui Chen, Ji-Na Cao, Guang-Chuan Liang

Journal of Electrochemistry

The residual powders of lithium-ion batteries at different voltages after explosion were obtained by using the battery impact testing machine. And these powders have been investigated by weighing, water solution and X-ray diffraction (XRD). The results showed that the integrity status of copper current collector and weight of residual powders decreased gradually with increasing of battery voltage, rising of burning temperature and releasing of burning duration time. The residual powders could be separated to insoluble powders and soluble powders by the water solution. The proportion of the insoluble powders is more (about 90%) including C, Co and CoO, while the …

Electrochemical Performance Of Tin Dioxide/Carbon Xerogel Composites As Anode Materials For Lithium-Ion Batteries, Xiao-Jing Liu, Lin-Lin Qin, Yi-Ning Shi, Ming-Sen Zheng, Quan-Feng Dong

Journal of Electrochemistry

The tin dioxide/carbon xerogel composites were synthesized by using vacuum infiltration method. Structural characterization and morphology of the composites were investigated by using XRD, TEM and SEM techniques. BET test was performed to determine the pore size distributions of carbon xerogels and the composites. The results showed that the nano-sized SnO₂ particles (5~10 nm) were encapsulated in the pores of carbon xerogels. During the electrochemical tests the SnO₂ in the composites exhibited capacity retention of 61.9% after 100 cycles of charge-discharge tests at 100 mA/g.

Study On The Fluorescent Carbon Nanodots With Electrochemical Methods, Bao-Ping Qi, Yan-Min Long, Lei Bao, Cui Liu, Zhi-Ling Zhang, Dai-Wen Pang

Journal of Electrochemistry

Carbon nanodots are a new class of fluorescent nanoparticles with a carbon-based core, which possess wavelength-tunable luminescence, high photostability, resistance to photobleaching, water-solubility, and ease of bioconjugation. Owing to their attractive merits, carbon nanodots like other carbon nanomaterials such as fullerene, carbon nanotubes and graphene, have attracted much attention. In addition, carbon nanodots can be inexpensively produced by electrochemical methods with simple post-processing under mild conditions. Electrochemical approaches have unique advantages in the analysis of surface structures and luminescence mechanism of materials. In this review, recent advances in electrochemical methods used for the synthesis and luminescence mechanism of fluorescent carbon …

Effects Of Graphene On Electrochemical Behaviors Of Ni(Oh)2 As Supercapacitor Material, Zhen-Zhen Zhao, Wen-Bin Ni, Neng-Yue Gao, Hong-Bo Wang, Jian-Wei Zhao

Journal of Electrochemistry

The enhanced electrochemical properties of Ni(OH)₂ by the oxidation defected graphene were studied by both experimental method and theoretical calculation. The composite material of nano-Ni(OH)₂/graphene was prepared by potentiostatic deposition on the graphene substrate. Observed by TEM, the Ni(OH)₂ nanoparticles were well dispersed on the graphene substrate with the diameter of 5.0±0.5 nm. The capacitance of the system measured by the electrochemical test was 1928 F·g^-1. As indicated by the theoretical calculations, the composite material becomes conductive since Ni(OH)₂ is combined with surface functional groups of the graphene through the strong chemical interaction. …

Photogenerated Cathodic Protection Of Stainless Steel, Cheng-Gang Lin, Ze-Quan Lin, Jing Li, Chang-Jian Lin

Journal of Electrochemistry

A highly ordered Co-doped TiO₂ nanotube layers were fabricated by potentiostatic anodization of pure titanium in fluorinated electrolyte solutions followed by ion-exchange method. The structure and composition of the as-prepared Co-doped TiO₂ nanotube layers were characterized by SEM, XRD, UV-Vis, and XPS. The effects of dopant content on the morphologies, structural and photochemical properties of the TiO₂ nanotube arrays were investigated. The performances of photogenerated cathodic protection and the photoelectrochemical response for the Co-doped TiO₂ nanotube arrays under illumination and dark conditions were evaluated through the electrochemical measurements. The Co-doped TiO₂ nanotubes showed a stronger …

Simultaneous Determination Of Dopamine(Da)And Epinephrine (Ep) At Ca/Gc Electrode, Wang Ren, Ying Zhang, Min-Jiao Li

Journal of Electrochemistry

The citric acid modified glassy carbon electrode (CA/GC) was prepared by potentiostatic technique and was used for detections of dopamine (DA), epinephrine (EP), and their mixtures by differential pulse voltammetry (DPV). The modified electrode shows the enhanced sensitivity and excellent electrochemical discrimination to DA and EP. The cathodic potential difference between DA and EP was about 380 mV, while no cathodic reduction of ascorbic acid (AA) was observed because the oxidation of AA is an irreversible reaction at the sensor. As a result, DA and EP could be determined simultaneously with the interferences of high concentrations of AA being eliminated. …

Study On The Electrochemical Behaviors Of Gc Electrode Modified With Carbon Nanotube-Polyelectrolytes And Its Application For Rutin Detection, Liang Hua, Xia-Qin Wu, Rong Wang

Journal of Electrochemistry

The electrochemical behaviors of rutin and ascorbic acid at single-wall carbon nanotube and polyelectrolytes (dimethyl-diallylammonium chloride, PDDA) film modified glassy carbon electrode was investigated. The cyclic voltammetric results showed that electron transfer of rutin at PDDA/SWCNTs/GC modified electrode is an adsorption-controlled process. The separation of oxidation peak potentials of rutin and ascorbic acid was more than 200 mV. The rutin concentration in the presence of AA were detected by differential pulse voltammetry (DPV). The experimental results indicated that the PDDA/SWCNTs/GC modified electrode can be used for the detection of rutin in the presence of high concentration of AA. The DPV …

Brief Introduction To Metal Corrosion And Protection, Hou-Yi Ma, Cong-Ying Cui, Ting Chen

Journal of Electrochemistry

This paper explains why corrosion processes are usually electrochemical in nature, describes the significance of electrochemical kinetic parameters of corrosion process, and briefly introduces the principles of corrosion protection, the most common corrosion protection methods and some special application of corrosion processes.

Surface Diffusion Of Adsorptive Species On Gold Nanoelectrodes, Bao-Fa Su, Wei Wang, Dong-Ping Zhan, Bin Ren, Zhong-Qun Tian

Journal of Electrochemistry

Gold nanoelectrodes were prepared successfully by a programmed laser puller. The Faraday adsorptions of oxygen and iodine, and the underpotential deposition of lead on the gold nanoelectrodes were investigated. The results showed that the active areas of nanoelectrodes were dramatically higher than their appearant geometry areas, which is caused by the surface diffusion of adsorptive species from the nanoscale gold/electrolyte interface to the adjacent gold surface.

Synthesis Of Limnpo4/C Used As Cathode Material For Lithium Ion Batteries, Xin Yang, Xue-Wu Liu, Gui-Chang Liu, Zhi-Cong Shi, Xin Li, Guo-Hua Chen

Journal of Electrochemistry

The LiMnPO₄/C composites were prepared using a solid-state reaction with addition of the resorcinol formaldehyde resin as the carbon source. The effects of reaction temperature and time on the crystal structure, morphology and electrochemical properties of the LiMnPO₄/C composites were investigated. The results show that the best performance was achieved with the LiMnPO₄/C composites synthesized at 600 ^oC for 12 h which had the particle sizes about 100~200 nm. The initial discharge capacities were 121.6 mAh·g^-1 at 0.02C, 110 mAh·g^-1 at 0.1C and more than 60 mAh·g^-1 at 1C. An …

Synthesis And Electrochemical Behaviors Of Li2Coxmn1-XSio4 As A Cathode Material For Lithium-Ion Batteries, Lin Wang, Dong-Ping Lv, Yong Yang

Journal of Electrochemistry

We have successfully synthesized Li₂Co_xMn_1-xSiO₄/C (x=0, 0.1, 0.3, 0.5, 1)/C composites using hydrothermal assisted sol-gel process and ball-milling method. The results of X-ray diffraction show that the solid solutions of Li₂Co_xMn_1-xSiO₄ can be achieved when x≤0.3. The initial capacities increase from 70 mAh·g^-1 of Li₂MnSiO₄/C to 105 mAh·g^-1 of Li₂Co_0.3Mn_0.7SiO₄/C. Cyclic Voltammetry (CV) curves show that the replacement of Mn with Co can reduce the electrochemical polarization, making the insertion-extraction reaction …

Corrosion Characteristics Of Galvanized Flat Steel For Power Grounding In Nacl Solution Medium, Yong Li, Gao-Lin Wu, Bang-Fei Deng, Ping Yang, Xue-Ming Li, Qing-Bin Zong

Journal of Electrochemistry

The corrosion behavior of power grounding galvanized flat steel was studied by polarization measurement, electrochemical impedance spectroscopy and neutral salt spray test in 5% NaCl solutions. The surface morphologies of galvanized coating and structural properties of corrosion products were observed with scanning electron microscope and X-ray diffraction spectrometer, respectively. Results showed that under the temperatures of 20~60℃, the corrosion currents of galvanized flat steel increased with the temperature rising. The corrosion rate at 60℃ was 0.8408 mA·cm^-2, which is 2.9 times larger than that at 20℃. The corrosion rate dropped after reaching the maximal value of 1.95 mg·cm …

Energy - Activities, Jane Qiong Zhang, Linda Vanasupa

Materials Engineering

The document contains activities for students in higher education. These activities are focused on energy issues related to sustainability. It is designed for the general engineering or science audience. Its design is based on the framework of the Fink Taxonomy of Significant Learning. Each activity includes a profile that indicates whether the activity involves direct or indirect information sources, whether the experience is doing or observing and whether it involves individual or group reflection. The profile also includes notes for faculty, an estimate of the time investment, a graphic of the developmental aims with respect to the six areas of …

Fink Taxonomy Of Significant Learning, Jane Qiong Zhang, Linda Vanasupa

Materials Engineering

This document is graphical summary of the framework within the Fink Taxonomy of Significant Learning and the definition of each of the six areas of significant learning.

Sustainable Development, Jane Qiong Zhang, Linda Vanasupa

Materials Engineering

This document is a set of learning materials to support the teaching of Sustainable Development issues particularly related to sustainability in engineering. It is designed for the general engineering or science audience. Its design is based on the framework of the Fink Taxonomy of Significant Learning. The document is a fully-editable set of slides in open source format (pptx) that includes references to targeted learning objectives on each slide and annotations in the notes section of each slide.

Water - Activities, Jane Qiong Zhang, Linda Vanasupa

Materials Engineering

The document contains activities for students in higher education. These activities are focused on water issues related to sustainability. It is designed for the general engineering or science audience. Its design is based on the framework of the Fink Taxonomy of Significant Learning. Each activity includes a profile that indicates whether the activity involves direct or indirect information sources, whether the experience is doing or observing and whether it involves individual or group reflection. The profile also includes notes for faculty, an estimate of the time investment, a graphic of the developmental aims with respect to the six areas of …