Engineering Commons^™

High-Speed Imaging Of A Bulk Metallic Glass During Uniaxial Compression, Wendelin Wright, Rachel R. Byer, Xiaojun Gu

Faculty Journal Articles

High-speed imaging directly correlates the propagation of a particular shear band with mechanical measurements during uniaxial compression of a bulk metallic glass. Imaging shows shear occurs simultaneously over the entire shear plane, and load data, synced and time-stamped to the same clock as the camera, reveal that shear sliding is coincident with the load drop of each serration. Digital image correlation agrees with these results. These data demonstrate that shear band sliding occurs with velocities on the order of millimeters per second. Fracture occurs much more rapidly than the shear banding events, thereby readily leading to melting on fracture surfaces.

Microstructure And Mechanical Properties Of A Friction Stir Processed Ti-6al-4v Alloy, Jianqing Su, Jiye Wang, Rajiv S. Mishra, Ray Xu, John A. Baumann

Materials Science and Engineering Faculty Research & Creative Works

Friction stir processing (FSP) trials were performed on 2mm-thick Ti-6Al-4V sheets using various processing parameters including tool rotational speed (800-1000RPM) and tool traverse speed (1-4IPM). A processing window was established with the W-1% La₂O₃ tool to produce defect-free friction stir processed (FSP'd) materials. The stir zone (SZ) material of the FSP'd samples showed a fully Β transformed microstructure characterized by typical basket-weave lamellar α/Β structure. The prior Β grains in the SZs contained multiple α variants, and the average sizes ranged from 12μm to 38μm influenced by the processing parameters. Based on metallurgical evaluation, the microstructural evolution …

On Electric Conduction Of Amorphous Silicon Carbonitride Derived From A Polymeric Precursor, Yaohan Chen, Fuqian Yang, Linan An

Chemical and Materials Engineering Faculty Publications

A long-existing problem that the conductivity of amorphous silicon carbonitrides derived from polymeric precursor increases significantly with pyrolysis temperature is investigated. We show that the conductivity exhibited an Arrhenius dependence on pyrolysis temperature, with the activation energy of ∼3.41 eV. Structural analysis using Raman spectroscopy reveals that the free carbon within the material undergoes a sp³-to-sp² transition as pyrolysis temperature increases, with the activation energy of ∼3.6 eV. We conclude that the pyrolysis-temperature induced increase in the conductivity is mainly due to the increase in the conductivity of the free carbon. A simple model is proposed to …

Glass-Ceremics For The Innovative Secondary Batteries, Tsuyoshi Honma

Functional Glasses: Properties And Applications for Energy and Information

No abstract provided.

Materials Education And Research In Art And Design: A New Role For Libraries (Survey Stats), Mark Pompelia

Materials Education and Research in Art and Design: A New Role for Libraries

No abstract provided.

Materials Education And Research In Art And Design: A New Role For Libraries (Program Sheet), Mark Pompelia

Materials Education and Research in Art and Design: A New Role for Libraries

No abstract provided.

Materials Education And Research In Art And Design: A New Role For Libraries (Program Booklet), Mark Pompelia

Materials Education and Research in Art and Design: A New Role for Libraries

No abstract provided.

Materials Education And Research In Art And Design: A New Role For Libraries (Website), Mark Pompelia

Materials Education and Research in Art and Design: A New Role for Libraries

No abstract provided.

Materials Collection Creation And Administration: A New Role For Libraries (White Paper), Mark Pompelia

Materials Education and Research in Art and Design: A New Role for Libraries

The Problem/Opportunity: To define, identify, and guide design-based materials collections in academic settings and foster community among those with existing collections and/or those considering creating and supporting one.

Contents and topics:

1. What is a materials collection?
2. Why have a materials collection?
3. Acquisition strategies
4. Organizational approaches
5. Programming possibilities
6. Symposium summary
7. Resources

Mechanical Properties And Microstructures Of Incoloy 909 Rolled Rings Subjected To A Modified Forging Cycle, Colin Lee Elliott Glaves

Materials Engineering

The microstructure of rolled rings of Incoloy 909 nickel-iron-cobalt superalloy subjected to a standard customer solution and aging treatment exhibited unacceptably large grains. Samples cut from a failed ring were mounted and polished for analysis. The samples were etched with a modified Kalling’s waterless reagent and metallographic analysis was done to identify characteristic large grain structures distributed among the desired smaller grain structures. The large grains were identified and noted for comparison to later samples. Two test rings were forged out of Incoloy 909 using revised forging procedures involving reduced soak temperatures before each forging step. Metallographic samples were cut …

Lunalight - Bringing Light To The Expanding World, Gabriela M. Igel, Daniel J. Patrick, Kimberley M. Smith

Materials Engineering

The LunaLight, a solar rechargeable light and cell phone charger, addresses the lack of access to electricity faced by 1.4 billion of the world’s population (International Finance Corporation). The LunaTech team has developed a product that is bright, simple, compact, versatile and competitive with existing products. Through a partnership with the non-profit organization One Million Lights, LunaTech has improved a previous team’s design to address user feedback, concerns of durability, and manufacturability.

The LunaLight design includes a 5 component plastic housing held together by 4 screws, a surface mounted PCB, a lithium-ion (Li-Ion) battery, one high-brightness LED, a solar panel, …

The Fabrication & Characterization Of An Electrokinetic Microfluidic Pump From Su-8, A Negative Epoxy-Based Photoresist, Nash Anderson

Master's Theses

Microfluidics refers to manipulation, precise control, and behavior of fluids at the micro and nanoliter scales. It has entered the realm of science as a way to precisely measure or mix small amounts of fluid to perform highly controlled reactions. Glass and polydimethylsiloxane (PDMS) are common materials used to create microfluidic devices; however, glass is difficult to process and PDMS is relatively hydrophobic. In this study, SU-8, an epoxy based (negative) photoresist was used to create various electrokinetic microfluidic chips. SU-8 is commonly used in microelectromechanical design. Spin coating of various SU-8 formulations allows for 1 μm to 100 μm …

The Relationship Of Barcol Hardness And Interlaminar Shear Strength In Glass Reinforced Polyester Composite Laminates, Ann E. Livingston-Peters

Materials Engineering

Chopped strand mat E-glass layers were impregnated with isophthalic marine laminating resin by hand lay-up techniques. Once the primary laminate reached the desired Barcol hardness value, the secondary laminate was applied and allowed to cure. These samples were bonded together at hardness values of 10, 30, 50, 70, and 90 Barcol. Lamination was conducted at 70°F with 35% glass fibers and 65% polyester resin catalyzed with 1.5% methyl ethyl ketone peroxide. The target thickness of each laminate was 6mm for short-beam shear testing requiring eight layers of glass and resin. Using the procedures outlined in ASTM D-2344, each sample set …

Evaluation Of Corrosion Properties Of Proprietary Metal Alloy Stents For In-Vivo Use, Michael David Bremner

Materials Engineering

To assess corrosion rates of metal alloy bio-absorbable stents an experimental set-up was designed to mimic the coronary artery environment. The artery was modeled using 4mm diameter Tecoflex tubing and the metal alloy stents were inserted into the tubing using a catheter. As is the case in cardiac surgery, the catheter with the stent and a microballoon were maneuvered to the desired position. The microballoon was then slowly inflated to expand the stent and compress it against the tubing walls. The catheter and microballoon were then withdrawn. A circulating pump system was set up to cycle fetal bovine serum (FBS) …

Fluorescence Characterization Of Quantum Dots For Use As Biomarkers, Logan M. Grimes

Materials Engineering

Fluorescence profiles of quantum dots (QDs) were characterized to select the ideal QDs for encapsulation in phospholipids for use as biomarkers to selectively adhere to cancer cells. QDs were synthesized and extracted 0, 30, 60, and 90 seconds after precursor compounds were mixed. These extractions were isolated by extraction time. Portions from each vial were coated in a zinc sulfide shelling procedure, leaving at least half of the QD solution unshelled. These samples were characterized over four days to monitor fluctuations in fluorescence. This was done utilizing an Ocean Optics spectrometer in conjunction with Spectra Suite software. The central wavelength, …

Scanning Tunneling Spectroscopy Under Atmospheric Conditions To Characterize A Tungsten Tip Stm System For Use With Hydrogen Desorption, Ross Gregoriev

Materials Engineering

The electrical surface structure of (111) n-type silicon was investigated through the use of scanning tunneling spectroscopy (STS) to develop a model to determine oxide presence on a passivated silicon surface. I-V curves were obtained with a scanning tunneling microscope (STM) using a tungsten tip on various locations of passivated silicon while the passivation layer desorbed from the surface under standard atmospheric conditions. The derivative (dI/dV) of these curves then revealed the electronic structure of the surface of the sample. Through these scans, it was determined the system was operating in the same mode as a Shockley diode. The separation …

Preparation Of A Polylactic Acid With Hydroxyapatite Reinforcement Composite, Odessa N. Quezon

Materials Engineering

Biodegradable polymers are a prime material choice for temporary biomedical devices due to its ability to degrade into non-toxic products for their use in vivo. However, polylactic acid (PLA) by itself lacks the sufficient strength and stiffness to permit their use as its properties begin to decrease as the polymer degrades. To improve the polymer’s mechanical properties, hydroxyapatite (HA) will be added to the PLA solution to act as reinforcement. The chemical property, glass transition temperature of a polymer, also plays a key role in the mechanical properties of the polymer. PLA’s glass temperature is 130⁰F. A polymer that …

Strength Testing And Material Characterization Of Cactus Spines, Mary Cooper, Jeff Goldstein, Thomas Tarlton

Materials Engineering

Twelve different species of cactus spines from 6 different genera were collected from living specimens and maintained in a dry storage environment. Spines from each species underwent 3-point bend testing, XRD testing, and SEM imaging. XRD analysis was used to verify the presence of cellulose whisker like nanocrystals and to calculate the percent crystallinity of each spine. SEM images were captured of fracture surfaces at viewing angles of 90° and 45° relative to the fracture surface, with magnifications ranging between 150x and 4,000x. A total of six spines from each species were tested in three point bending using a high-resolution …

The Effects Of Heat Treatment On The Grain Growth, Phase Evolution, And Hardness Of Newly Developed Steel-Based Hardfacing Alloys For Industrial Applications, Renee Kuzniar

Materials Engineering

Steel-based hardfacing alloys are welded onto the outside diameter of tool joints in three beads with a slight overlap between welds for underground drilling to prolong the tool joints’ life. Current hardfacing alloys have a shortened life due to cracks occurring in neighboring weld beads. To decrease cracking, the effects of composition and heat treatment on the microstructure was investigated on five alloys. Five small arc-melt circular ingots roughly 1.4 x 0.3 inches were produced. Each sample had varying amounts of C, B, Cr, Mn, Mo, Nb, Si, Ti, V, and W. The carbon levels in the alloys were .91wt%, …

Grain Size Control In Post-Forged C263 Seamless Rolled Rings, Christopher Smith

Materials Engineering

Seamless rolled rings of C263 superalloy were forged by Carlton Forge Works in Paramount, CA and sectioned for mechanical testing. The as-forged ring sections were then machined into tensile samples. To simulate cold working done after Carlton’s forging process, the C263 tensile samples were strained using an Instron tensile tester to 1, 3, 5, 7, and 9% plastic strain. These tensile samples were then solution treated at 2100°F for 30 minutes and water quenched before being aged at 1470°F for 8 hours and air cooled, following Carlton Forge Works’ heat treatment process. The gauge length sections were metallographically prepared and …

Simplifying The Testing And Calculation Of Fracture Toughness Of Thermoplastic And Thermoset Matrix Composite Materials, James Shedden

Materials Engineering

Fracture toughness, or the ability of a material to resist fast fracture by crack propagation is an important property in the use of composite materials for structural designs. Other mechanical tests such as tensile, flexure, and compression are more established and practical than testing fracture toughness. Fracture toughness testing is less commonly used because it requires specific specimens and non-conventional test methods. In composite materials specifically, delamination of the plies of materials is tested for G_IC and G_IIC values to find the critical strain energy release rate of the two types of fracture modes. The common two tests …

Development Of A Production Line Appropriate Test For Teflon Adhesion On 304 Stainless Steel 0.01-0.03" Diameter Coronary Guide Wires, Danielle Dunham

Materials Engineering

A test was developed to determine relative adhesion of Teflon-coated 304 stainless steel guide wires. Two sets of wires were provided by Abbott Vascular for testing: one set was known to have poor Teflon adhesion, the other had acceptable adhesion. A prototype device was designed and manufactured that produced a shear force on the coating by dragging the wire under a ½ inch-diameter 440C hardened stainless steel cylinder. Testing consisted of increasing the force on the wire during each consecutive pass with the cylinder until the Teflon coating failed. The force on the wire during the failure producing pass was …

Residual Stress Measurement Of 7050 Aluminum Alloy Open Die Forgings Using The Hole-Drilling Method, Alexandra Viksne

Materials Engineering

Open die forged 7050 aluminum alloy has residual stresses that can be measured by the hole-drilling method following standard ASTM E837-01. Weber Metals (Paramount, CA) assumes that the stress is uniform throughout the thickness of an open die forged plate. Four different stress relieved 7050 aluminum samples were tested to confirm if the measurements by the hole-drilling method at the surface of a plate is indicative of the stress throughout. The different stress relief methods included: two water quenched samples at temperature ranges of 60°-90°F and 120°-130°F and two samples plastically deformed by forging at room temperature 1% and 3%. …

Analyzing The Flexural Properties Of Self-Constructed Bamboo Laminates, Brett Dorren

Materials Engineering

Bamboo plies of 1/8" and 1/32" thicknesses were glued together to form multiple unidirectional and cross-ply laminates that measured 12" by 12". The thickness of each laminate was between 0.25" and 0.375". All laminates were pressed together with a Tetrahedron MTP-10 bench top precision press at 75°F and 1000 lb_f for 40 minutes. Laminates were then cut with a band-saw into four 3" by 12" test specimens, 24 hours after pressing. Each test specimen was three-point bend tested to identify the modulus of rupture (MOR) and apparent bending stiffness. Three-point bend testing was also performed on laminates that were …

Evaluation Of High Phosphorus Electroless Nickel Platings To Protect Carbon Steel Heat Exchangers In Seawater Service, Nathan Brink

Materials Engineering

The purpose of this project was to determine the suitability of using a high phosphorus electroless nickel (HPEN) coating to prevent corrosion in carbon steel heat exchangers in seawater service. 1 in. x 4 in. samples were cut from ¼ in. SA-516-70 pressure vessel plate, pickled to remove mill scale, dressed with 300 grit sand paper and sent out for plating with 2 mils of HPEN. Due to a clerical error during plating, samples were plated to a significantly lesser extent than requested. Samples were plated with approximately 0.6 mils of HPEN versus the 2 mils requested, however this was …

Measuring The Mechanical Properties Of A Newly Developed Discontinuous Carbon Fiber And Epoxy Composite, Morgan Adams

Materials Engineering

Engineering firm Pratt & Miller have developed a new and previously untested carbon fiber/epoxy composite using a spray lay-up process similar to a process commonly used in fiberglass production. This new composite is made by using a pneumatic chop gun that simultaneously cuts the carbon fibers to a specific length and deposits the chopped fibers and resin onto surface of an exposed mold surface. The composite is then rolled down to flatten and better wet the fibers and then the whole mold is vacuum bagged at room temperature to cure. The flexural stiffness and flexural strength of the composite with …

Tensile Properties Of Adhesive Joints Between Alclad 2024-T3 Aluminum Sheets And Extruded 6061-T6511 Aluminum For Use In Ultralight Personal Aircraft, Kevin Jones

Materials Engineering

Cold cure two-part epoxy adhesives were tested in aluminum joints to investigate their viability for use in an ultralight aircraft. The joints consisted of Alclad 2024-T3 aluminum sheets adhesively bonded to extruded 6061-T6511 aluminum, and are part of low-load-bearing members required to carry a minimum load of 175 lbs./ft. or 14.58 lbs./in. The Alclad 2024-T3 and 6061-T6511 aluminum were prepared by sanding with 80 grit abrasive paper, the surface was cleaned with acetone to remove surface contaminants, rinsed with distilled water, and dried using paper towels. Once the surface was prepared, the test coupons were assembled using one of the …

Design Of A Children’S Earth Science Exhibit For The Exploration Station In Grover Beach, California With An Emphasis On Fog Collection, Kathryn Thomas

Materials Engineering

An outdoor earth science museum exhibit was designed for the Exploration Station in Grover Beach, California, and will use the harvesting methods of fog as a clean water resource to educate children. The design of the exhibit has two parts: a 1 m x 1 m static Standard Fog collector for long term fog collection which rises 2 m off the ground, and a mobile six-panel display consisting of six different materials and structures of meshes, all of which could potentially be used in a large scale fog collection setting. The six-panel portion will present the children with a hands-on …

Thermally Insulating Coating For Steel Drill Pipe, Matthew Mccaffrey

Materials Engineering

A 5/16 in thick, 6 in x 6 in steel plate was used as a simple analog to 4 inch grade “S” steel drill pipe. Ethylene tetraflouroethylene (ETFE) applied as a powder coating was selected as the desired thermally insulating coating because of its excellent chemical resistance, maximum service temperature of 300°C, its thermal conductivity of 0.238 W/m-K, and for its ability to be applied in thicknesses of up to 80 mils. A powder primer coat of approximately 2 mils was applied using a conventional corona electrostatic powder sprayer, and then the high build topcoat was applied directly over the …

Design And Construction Of A Simulated Evaporative Heat Exchanger For Testing The Mitigation Effects Of Pipe Coatings On Mineral Scale Deposition, Taylor J. Anderson

Materials Engineering

The thermal efficiency of evaporative heat exchangers is diminishing due to mineral scale buildup on heat exchanger surfaces. A simulated evaporative heat exchanger was designed and constructed for testing the mitigation effects of polymer coatings on mineral scale deposition rates. The heat exchanger was designed to cool hot mud at 200°F using a cooling water supply with a calcium concentration of 1000 ppm. The system was constructed using 1.5-inch diameter polypropylene piping, a DIG Corporation drip irrigation system, a TotalPond 530 GPH pond pump, an Omega CSI32K miniature benchtop controller, Omega FWH321-020 high temperature heater tape, and fifteen copper pipe …