Engineering Commons^™

High Field Breakdown Characteristics Of Carbon Nanotube Thin Film Transistors, Man Prakash Gupta, Ashkan Behnam, Feifei Lian, David Estrada, Eric Pop, Satish Kumar

Materials Science and Engineering Faculty Publications and Presentations

The high field properties of carbon nanotube (CNT) network thin film transistors (CN-TFTs) are important for their practical operation, and for understanding their reliability. Using a combination of experimental and computational techniques we show how the channel geometry (length L_C and width W_C) and network morphology (average CNT length L_t and alignment angle distribution θ) affect heat dissipation and high field breakdown in such devices. The results suggest that when W_C ≥ L_t, the breakdown voltage remains independent of W_C but varies linearly with L_C. The breakdown power varies …

Analyzing Hexavalent Chromium (Cr Vi)-Free Paint Systems For Sls, Maria Emma Torres

Von Braun Symposium Student Posters

No abstract provided.

Zno Nanoneedle/H2o Solid-Liquid Heterojunction-Based Self-Powered Ultraviolet Detector, Qinghao Li, Lin Wei, Yanru Xie, Kai Zhang, Lei Liu, Dapeng Zhu, Jun Jiao, Yanxue Chen, Shishen Yan, Guolei Liu, Liangmo Mei

Physics Faculty Publications and Presentations

ZnO nanoneedle arrays were grown vertically on a fluorine-doped tin oxide-coated glass by hydrothermal method at a relatively low temperature. A self-powered photoelectrochemical cell-type UV detector was fabricated using the ZnO nanoneedles as the active photoanode and H2O as the electrolyte. This solid-liquid heterojunction offers an enlarged ZnO/water contact area and a direct pathway for electron transport simultaneously. By connecting this UV photodetector to an ammeter, the intensity of UV light can be quantified using the output short-circuit photocurrent without a power source. High photosensitivity, excellent spectral selectivity, and fast photoresponse at zero bias are observed in this UV detector. …

A Tensile Deformation Model For In-Situ Dendrite/Metallic Glass Matrix Composites, J. W. Qiao, T. Zhang, Fuqian Yang, P. K. Liaw, S. Pauly, B. S. Xu

Chemical and Materials Engineering Faculty Publications

In-situ dendrite/metallic glass matrix composites (MGMCs) with a composition of Ti₄₆Zr₂₀V₁₂Cu₅Be₁₇ exhibit ultimate tensile strength of 1510 MPa and fracture strain of about 7.6%. A tensile deformation model is established, based on the five-stage classification: (1) elastic-elastic, (2) elastic-plastic, (3) plastic-plastic (yield platform), (4) plastic-plastic (work hardening), and (5) plastic-plastic (softening) stages, analogous to the tensile behavior of common carbon steels. The constitutive relations strongly elucidate the tensile deformation mechanism. In parallel, the simulation results by a finite-element method (FEM) are in good agreement with the experimental findings and theoretical calculations. The present study gives a mathematical model to clarify …

Modeling The Atomic And Electronic Structure Of Metal-Metal, Metal-Semiconductor And Semiconductor-Oxide Interfaces, Ganesh Krishna Hegde

Open Access Dissertations

The continuous downward scaling of electronic devices has renewed attention on the importance of the role of material interfaces in the functioning of key components in electronic technology in recent times. It has also brought into focus the utility of

atomistic modeling in providing insights from a materials design perspective. In this thesis, a combination of Semi Empirical Tight-Binding (TB), first-principles Density

Functional Theory and Reactive Molecular Dynamics (MD) modeling is used to study aspects of the electronic and atomic structure of three such 'canonical' material interfaces - Metal-Metal, Metal-Semiconductor and Semiconductor oxide interfaces.

An important contribution of this thesis …

Soil Nutrient Availability Properties Of Biochar, Nicole C. Esposito

Master's Theses

Biochar’s high porosity and negative surface charge allows for numerous soil and plant benefits such as increased water retention, high nutrient availability, and plant growth. By analysing biochar’s effect of all of these factors, a system can be put in place in which soils can be remediated with the proper soil amendments. This report discusses and tests the effects of varying rates of biochar on pH levels, cation exchange capacity, and nutrient exchangeability (of calcium, magnesium, sodium, and potassium) in soil. Corn plants were also grown in soils of varying amendment types and analysed for plant growth and germination to …

Spectroscopic And Kinetic Characterization Of Catalytic Materials For The Conversion Of Biomass-Derived Compounds, Paul James Dietrich

Open Access Dissertations

As economies look to transition away from petroleum for social, economic, and political reasons, biomass will continue to attract attention as a renewable feedstock for the fuels and chemicals industry. In order to turn biomass into end use fuels and chemicals, the oxygen content must be lowered significantly, requiring large hydrogen inputs. For these processes to be completely renewable, the hydrogen must come from biomass or biomass-derived compounds. In this work, catalysts for the aqueous phase reforming (APR) of biomass-derived sugars were characterized by a combination of reaction kinetics, X-ray spectroscopy, electron microscopy, and theoretical computation to determine the active …

The Comparison Of Composite Aircraft Field Repair Method (Cafrm) With Traditional Aircraft Repair Technologies, Peng Hao Wang

Open Access Dissertations

In the aviation industry, manufacturers made the transition from aluminum to composite materials for the majority of their primary structures over the last few decades. While the design and manufacturing techniques have consistently evolved, field repair methods were consistently overlooked. In this study, specimens fabricated using some of the common repair methods such as the autoclave repair method, and Double Vacuum Debulk (DVD) repair method were tested against the Composite Aircraft Field Repair Method (CAFRM) proposed by the researcher. Specimens were tested with microscopy, acid digestion, short beam shear, and mode I fracture tests. The researcher was able to determine …

Synthesis Of Graphene Nanomaterials And Their Application In Electrochemical Energy Storage, Guoping Xiong

Open Access Dissertations

The need to store and use energy on diverse scales in a modern technological society necessitates the design of large and small energy systems, among which electrical energy storage systems such as batteries and capacitors have attracted much interest in the past several decades. Supercapacitors, also known as ultracapacitors, or electrochemical capacitors, with fast power delivery and long cycle life are complementing or even replacing batteries in many applications. The rapid development of miniaturized electronic devices has led to a growing need for rechargeable micro-power sources with high performance. Among different sources, electrochemical micro-capacitors or micro-supercapacitors provide higher power density …

Dynamic Behavior Of Sandwich Beams With Internal Resonators, Bhisham Nar Narain Sharma

Open Access Dissertations

Dynamic behavior of sandwich beams with internal resonators was investigated. The effect of inserting spring-mass resonators into the sandwich core was theoretically analyzed and it was shown that a wave attenuation bandgap exists due to local resonance. Steady state experiments were used to demonstrate such an attenuation bandgap. Frequency response functions were obtained for a beam with resonators and without resonators. It was shown that insertion of resonators into the core causes a wave attenuation bandgap to open up. The experimental results were verified using finite element simulations. Further experiments were carried out by tuning the resonators at 12 Hz …

Mechanisms Of Microstructure Formation Under The Influence Of Ultrasonic Vibrations, Milan Rakita

Open Access Dissertations

Positive effects of ultrasound on crystallization have been known for almost 90 years. Application of ultrasound has been very successful in many industries, most notably in chemistry, creating a new branch of science - sonochemistry. However, ultrasonication has not found wide commercial application in the solidification processing. The reason for that is the complexity of underlying phenomena and the lack of predicting models which correlate processing parameters with the properties of a product. The purpose of this study is to give some contribution toward better understanding of mechanisms that lead to changes in the solidifying microstructure. It has been found …

Utilizing Electron Microscopy And Spectroscopy Methods To Understand Water Structure And Water Doping, Lior Miller

Open Access Dissertations

Water is the second most common element in the universe and the most studied material on earth. Most of the studies concerning water are from the fields of chemistry and biology. Hence, the structure of water molecules and short range order and interactions are well characterized and understood. However, the collective arrangement of water molecules and the long range order are still missing. Understanding of this long range order in water is needed, as it is the key to many water activities.

To fill this gap, this study utilizes a new direct method for characterization of water in the vapor …

The Effect Of Composition On The Linear And Nonlinear Mechanical Properties Of Particulate Filled Elastomers, Oluwaseyi Ogebule

Open Access Dissertations

Engineering elastomers are materials capable of undergoing large deformation upon load application and recovering upon load removal. From car tires to building vibration isolator systems, elastomers are the most versatile of engineering materials. The inclusion of particulate fillers into elastomers enhances their mechanical properties (modulus, tensile strength, toughness, tear resistance, etc) thereby extending their applicability to more demanding functions. The automotive, healthcare, construction, adhesives and consumer products are some of the many industries that produce finished goods containing elastomeric parts.

Despite the various concepts on reinforcement in filled elastomers, a complete understanding of their linear viscoelastic properties and the nonlinear …

Response Of Plasma Facing Components In Tokamaks Due To Intense Energy Deposition Using Particle-In-Cell(Pic) Methods, Filippo Genco

Open Access Dissertations

Damage to plasma-facing components (PFC) due to various plasma instabilities is still a major concern for the successful development of fusion energy and represents a significant research obstacle in the community. It is of great importance to fully understand the behavior and lifetime expectancy of PFC under both low energy cycles during normal events and highly energetic events as disruptions, Edge-Localized Modes (ELM), Vertical Displacement Events (VDE), and Run-away electron (RE). The consequences of these high energetic dumps with energy fluxes ranging from 10 MJ/m2 up to 200 MJ/m2 applied in very short periods (0.1 to 5 ms) can be …

Solution To Certain Problems In The Failure Of Composite Structures, Jonathan Goodsell

Open Access Dissertations

The present work contains the solution of two problems in composite structures. In the first, an approximate elasticity solution for prediction of the displacement, stress and strain fields within the m-layer, symmetric and balanced angle-ply composite laminate of finite-width subjected anticlastic bending deformation is developed. The solution is shown to recover classical laminated plate theory predictions at interior regions of the laminate and thereby illustrates the boundary layer character of this interlaminar phenomenon. The results exhibit the anticipated response in congruence with the solutions for uniform axial extension and uniform temperature change, where divergence of the interlaminar shearing stress is …

Multiscale Modeling Of The Hierarchical Structure Of Cellulose Nanocrystals, Fernando Luis Dri

Open Access Dissertations

Cellulose constitutes the most abundant renewable polymeric resource available today. It considered an almost inexhaustible source of raw material, and holds great promise in meeting increasing demands for environmentally friendly and biocompatible products. Key future applications are currently under development for the automotive, aerospace and textile industries. When cellulose fibers are subjected to acid hydrolysis, the fibers yield rod-like, highly crystalline residues called cellulose nanocrystals (CNCs). These particles show remarkable mechanical and chemical properties (e.g. Young Modulus ~200 GPa) within the range of other synthetically-developed reinforcement materials. Critical to the design of these materials are fundamental material properties, many of …

Applicability Of Continuum Fracture Mechanics In Atomistic Systems, Shao-Huan Cheng

Open Access Dissertations

By quantitating the amplitude of the unbounded stress, the continuum fracture mechanics defines the stress intensity factor K to characterize the stress and displacement fields in the vicinity of the crack tip, thereby developing the relation between the stress singularity and surface energy (energy release rate G). This G-K relation, assigning physical meaning to the stress intensity factor, makes these two fracture parameters widely used in predicting the onset of crack propagation. However, due to the discrete nature of the atomistic structures without stress singularity, there might be discrepancy between the failure prediction and the reality of nanostructured materials. Defining …

Atomic Level Study Of Water-Gas Shift Catalysts Via Transmission Electron Microscopy And X-Ray Spectroscopy, Mehmed Cem Akatay

Open Access Dissertations

Water-gas shift (WGS), CO + H₂ O [Special characters omitted.] CO₂ + H₂ (ΔH° = -41 kJ mol ^-1 ), is an industrially important reaction for the production of high purity hydrogen. Commercial Cu/ZnO/Al₂ O₃ catalystsare employed to accelerate this reaction, yet these catalysts suffer from certain drawbacks, including costly regeneration processes and sulfur poisoning. Extensive research is focused on developing new catalysts to replace the current technology. Supported noble metals stand out as promising candidates, yet comprise intricate nanostructures complicating the understanding of their working mechanism.

In this study, the structure of the supported …

The Biological Impact Of Concurrent Exposure To Metallic Nanoparticles And A Static Magnetic Field, Kristen K. Comfort, Elizabeth I. Maurer, Saber M. Hussain

Chemical and Materials Engineering Faculty Publications

The rapid advancement of technology has led to an exponential increase of both nanomaterial and magnetic field utilization in applications spanning a variety of sectors. While extensive work has focused on the impact of these two variables on biological systems independently, the existence of any synergistic effects following concurrent exposure has yet to be investigated. This study sought to ascertain the induced alterations to the stress and proliferation responses of the human adult low calcium, high temperature keratinocyte (HaCaT) cell line by the application of a static magnetic field (approximately 0.5 or 30 mT) in conjunction with either gold or …

On The Uniqueness And Sensitivity Of Indentation Testing Of Isotropic Materials, J. K. Phadikar, T. A. Bogetti, Anette M. Karlsson

Mechanical Engineering Faculty Publications

Instrumented indentation is a popular technique to extract the material properties of small scale structures. The uniqueness and sensitivity to experimental errors determine the practical usefulness of such experiments. Here, a method to identify test techniques that minimizes sensitivity to experimental erros is in indentation experiments developed. The methods are based on considering “shape functions,” which are sets of functions that describe the force–displacement relationship obtained during the indentation test. The concept of condition number is used to investigate the relative reliability of various possible dual indentation techniques. Interestingly, it was found that many dual indentation techniques can be as …

Synthesis And Optimization Of Vo₂ Thin Films For Phase Transition Applications By Atomic Layer Deposition And Rf Magnetron Sputtering, Madhavi Tangirala

Electrical & Computer Engineering Theses & Dissertations

Among many Vanadium oxides and suboxides, VO₂ has received considerable attention due to its remarkable metal-insulator transition (MIT) or semiconductor-metal transition (SMT) behavior, a reversible change in its electrical and optical properties that occurs due to a phase transition near a temperature of 68°C. Electrically, the resistivity of VO₂ can be changed as large as 4-5 orders of magnitude. Optically, the transmittance drops dramatically above the transition temperature in the metallic state where the VO₂ film becomes highly reflective in the infrared region. All these properties result in structural phase transformation from a low temperature monoclinic to …

Capacitive Properties And Structure Of Ruo₂-Hfo₂ Films Prepared By Thermal Decomposition Method, Xuehua Liu, Junqiu Zhu, Xin Wang, Jinghua Sun, Zhongzhi Tang, Teng Zhang, Matthew O'Keefe, Dian Tang

Materials Science and Engineering Faculty Research & Creative Works

Binary RuO₂-HfO₂ films on Ti substrates were prepared by a thermal decomposition method. cyclic voltammetric and charge/discharge properties of the RuO₂-HfO₂ electrodes were characterized. It was determined that the incorporation of HfO₂ into RuO ₂ greatly improved the capacitive properties of the material. The RuO₂-HfO₂ electrodes showed excellent cyclic stability, with no decay in charge capability during 1000 CV cycles in acidic solution. A nominal content of 50 mol% RuO₂ and 50 mol% HfO₂ gave the highest specific capacitance of 789.3 F/g (RuO₂). The excellent capacitive …

Microstructural Evolution And Mechanical Properties Of Friction Stir Welded Ods Alloy Ma754, Jiye Wang, Wei Yuan, Rajiv S. Mishra, Indrajit Charit

Materials Science and Engineering Faculty Research & Creative Works

Microstructural evolution and mechanical properties of MA754, an yttrium oxide dispersion-strengthened nickel-based superalloy, were investigated after friction stir welding (FSW). A tool rotation rate of 1000 revolution per minute and a traverse speed of 50.8 mm per minute were employed using a cermet (WC-Co) tool. After FSW, fine equiaxed grain structure with a high dislocation density and a random texture was achieved. Agglomeration of yttrium oxide dispersoids was observed in FSW MA754. Room-temperature tensile properties of FSW MA754 were compared to those of as-received MA754 alloy, and the results indicated that particle strengthening contribution decreased as a result of dispersoid …

Enhanced Reducibility And Conductivity Of Na/K-Doped Srti0.8Nb0.2O3, Guoliang Xiao, Sirikanda Nuansaeng, Lei Zhang, Suwit Suthirakun, Andreas Heyden, Hans-Conrad Zur Loye, Fanglin Chen

Faculty Publications

Donor and acceptor co-doped SrTiO₃ materials have shown interesting features in their conductivity and reducibility. In this work, 10 mol% Na⁺ or K⁺ as acceptor dopants have been introduced into the A-site of donor-doped strontium titanate, SrTi_0.8Nb_0.2O₃, and the doping impact on their properties has been studied. By doping with Na or K, the sinterability of SrTi_0.8Nb_0.2O₃ in reducing atmospheres has been improved. Na_0.1Sr_0.9Ti_0.8Nb_0.2O₃ and K_0.1Sr_0.9Ti_0.8Nb_0.2O₃ show metallic …

Wound Care, Steven B. Jung, D. E. Day

Materials Science and Engineering Faculty Research & Creative Works

A method for treating a wound, and a dressing for wound care management comprising a three-dimensional body of glass-based fibers comprising one or more glass-formers selected from the group consisting of P₂O5, SiO₂, and B₂O₃; at least about 25 wt % of the fibers have a diameter between about 200 nm and about 4000 nm, and a length:width aspect ratio of at least about 10. In another form, the glasses are in the form of particles in an ointment or cream applied to a wound. In yet other forms the glasses are …

Solid State Pre-Formed Electronics Adhesive (Spea), Alexander Randon Cope

Dissertations and Theses

In mobile and handheld consumer electronic markets, product use conditions drive the requirement for mechanical strength and device durability. The majority of relatively large form factor electronic components in a laptop, mobile internet device, PDA, or mobile phone use an adhesive as a stiffener to help protect the component from physical stresses imposed by daily wear and tear. Described herein is an innovative solution referred to as Solid State Pre-Formed Electronics Adhesive (SPEA), which enables a decrease in circuit board manufacturing throughput time while increasing mechanical durability with a consistent and characterized adhesive application process.

Today, many consumer electronic ODM's …

Additivity Of Strengthening Mechanisms In Ultrafine Grained Al-Mg-Sc Alloy, N. Kumar, R. S. Mishra

Materials Science and Engineering Faculty Research & Creative Works

In the light of unique and anomalous properties of ultrafine grained (UFG) alloys, an effort was made to develop a predictive capability of the yield strength (YS) of UFG Al-Mg-Sc alloy. UFG microstructure was introduced using friction stir processing. Microstructural characterization of grain size, dislocations, and nano-sized Al3(Sc,Zr) particles was carried out using electron backscatter diffraction and transmission electron microscope. The contribution from Peierls-Nabarro stress, solid solution strengthening, precipitation strengthening, grain boundary strengthening, and dislocation strengthening were assessed using existing strengthening models. Additivity law to predict the YS of the alloy was chosen based on the microstructural state of the …

Quantum Computing Circuits, Cheng-Hsiao Wu, Casey Andrew Cain

Electrical and Computer Engineering Faculty Research & Creative Works

A system for performing digital operations, including a first device configured to transform a digital input into one or more signals, at least one AB ring, the at least one AB ring irreducibly-coupled and configured to include at least three terminals, a second device configured to read a portion of a signal expressed upon two or more of the at least three terminals, and a third device configured to transform the portion of the signal expressed upon two or more of the at least three terminals into a digital output, the third device operationally connected to the second device.

Fabrication And Characterization Of A Palladium/Porous Silicon Layer, Nicholas Hong Lui

Master's Theses

When porous silicon is plated with a catalytic metal, the two materials can act together as a single entity whose electrical properties are sensitive to its environment – the sensing component of an electrochemical gas sensor. Etching pores into silicon is an electrochemical process; and which type of doped silicon used is one of its key parameters. For nearly all reported porous silicon gas sensors, the silicon has been of the p-doped variety – because p-doped porous etching is better understood and the layers that result from it are more predictable – despite n-doped silicon having potentially significant benefits in …

Metal-Assisted Etching Of Silicon Molds For Electroforming, Ralu Divan, Dan Rosenthal '14, Karim Ogando, Leonidas E. Ocola, Daniel Rosenmann, Nicolaie Moldovan

Student Publications & Research

Ordered arrays of high-aspect-ratio micro/nanostructures in semiconductors stirred a huge scientific interest due to their unique one-dimensional physical morphology and the associated electrical, mechanical, chemical, optoelectronic, and thermal properties. Metal-assisted chemical etching enables fabrication of such high aspect ratio Si nanostructures with controlled diameter, shape, length, and packing density, but suffers from structure deformation and shape inconsistency due to uncontrolled migration of noble metal structures during etching. Hereby the authors prove that a Ti adhesion layer helps in stabilizing gold structures, preventing their migration on the wafer surface while not impeding the etching. Based on this finding, the authors demonstrate …