Engineering Commons^™

Shape Memory Behavior Of Single And Polycrystalline Nickel Rich Nickel Titanium Alloys, Irfan Kaya

Theses and Dissertations--Mechanical and Aerospace Engineering

NiTi is the most commonly used shape memory alloy (SMA) and has been widely used for bio-medical, electrical and mechanical applications. Nickel rich NiTi shape memory alloys are coming into prominence due to their distinct superelasticity and shape memory properties as compared to near equi-atomic NiTi shape memory alloys. Besides, their lower density and higher work output than steels makes these alloys an excellent candidate for aerospace and automotive industry. Shape memory properties and phase transformation behavior of high Ni-rich Ni₅₄Ti₄₆ (at.%) polycrystals and Ni-rich Ni₅₁Ti₄₉ (at.%) single-crystals are determined. Their properties are sensitive …

Precipitation, Orientation And Composition Effects On The Shape Memory Properties Of High Strength Nitihfpd Alloys, Emre Acar

Theses and Dissertations--Mechanical and Aerospace Engineering

NiTiHf high temperature shape memory alloys are attractive due to their high operating temperatures (>100 ^oC) and acceptable transformation strain compared to NiTi. However, NiTiHf has limitations due to their lack of ductility and low strength, resulting in poor shape memory properties. In this study, Pd has been added to NiTiHf alloys in an attempt to improve their shape memory behavior. A combined approach of quaternary alloying and precipitation strengthening was used.

The characterization of a Ni_45.3Ti_29.7Hf₂₀Pd₅ (at. %) polycrystalline alloy was performed in compression after selected aging treatments. Transmission electron …

Microstructure And Chemistry Evaluation Of Direct Metal Laser Sintered 15-5 Ph Stainless Steel, Kevin Coffy

Electronic Theses and Dissertations

15-5PH stainless steel is an important alloy in the aerospace, chemical, and nuclear industries for its high strength and corrosion resistance at high temperature. Thus, this material is a good candidate for processing development in the direct metal laser sintering (DMLS) branch of additive manufacturing. The chemistry and microstructure of this alloy processed via DMLS was compared to its conventionally cast counterpart through various heat treatments as part of a characterization effort. The investigation utilized optical microscopy, scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-Ray diffractometry (XRD), energy dispersive X-Ray spectroscopy (EDS) and glow discharge atomic emission spectrometry (GDS) …

Graphene Oxide Reinforcement In Plasma Sprayed Nickel-5%Aluminum Coatings, David Ward

Electronic Theses and Dissertations

Metallic plasma sprayed coatings are widely used in the aerospace industry for repair on worn engine components. However, the inherent defects in these coatings limit the variety of repairs and reduce the service life of the repaired parts. A potential solution to overcome this problem is to mix small amounts of inexpensive graphene oxide in the powder feedstock. The incredible strength to weight ratio of graphene oxide makes it a viable additive to improve mechanical properties of metallic plasma sprayed coatings. The powder system chosen for this research is Nickel-5Aluminum since it is a common coating for such repairs. The …

Processing And Characterization Of Multifunctional Thermoplastic Nanocomposite Films, Xin Wang

Electronic Theses and Dissertations

Nanoparticles reinforced polymer composite films have been widely studied for their enhanced mechanical, electrical and thermal properties compared with host polymer matrix. However, most research was conducted on incorporation of nanoparticles in polymer films to improve single property and there is a lack of research on the multifunctional polymer nanocomposite films. In this work, a scalable and continuous spray deposition process was developed for the production of nanoparticles reinforced multifunctional thermoplastic nanocomposite films. This process is capable of making a thin sheet of thermoplastic nanocomposites with high nanoparticle loadings. The smallest thickness can be 40um. The objective of this study …

Development And Analysis Of Low Calcium Flyash Based Geopolymer For Structural Applications, Gaurav Nagalia

Material Science and Engineering Theses - Archive

Geopolymers are an innovative ceramic material composed of long chains and networks of inorganic molecules are being used as an alternative to conventional Portland cement for infrastructure construction, replacement of intersection and localized repairs. Some of the advantages of this material is due to its ultra-fast setting time, rapid strength development and the phenomenal reduction in carbon foot print as compared to Portland cement. However, this material is yet to be commercialized due to the variability in its mechanical strength when using flyash from different sources. In this study aluminosilicate geopolymers with different alkali oxides (feldspars) have been prepared by …

Stm Study Of Pulsed Laser Assisted Growth Of Ge Quantum Dot On Si(1 0 0)-(2 × 1), Ali Orguz Er, Hani E. Elsayed-Ali

Electrical & Computer Engineering Faculty Publications

Ge quantum dot formation on Si(1 0 0)-(2 × 1) by nanosecond pulsed laser deposition under laser excitation was investigated. Scanning tunneling microscopy was used to probe the growth mode and morphology. Excitation was performed during deposition using laser energy density of 25-100 mJ/cm ². Faceted islands were achieved at a substrate temperature of ∼250 °C only when using laser excitation. The island morphology changes with increased laser excitation energy density although the faceting of the individual islands remains the same. The size of the major length of islands increases with the excitation laser energy density. A purely electronic …

Physical Analysis Of Vo2 Films Grown By Atomic Layer Deposition And Rf Magnetron Sputtering, Madhavi Tangirala, Kai Zhang, David Nminibapiel, Venkateswara Pallem, Christian Dussarrat, Wei Cao, Thomas N. Adam, Corbet S. Johnson, Hani E. Elsayed-Ali, Helmut Baumgart

Electrical & Computer Engineering Faculty Publications

Among the many vanadium suboxides and different stoichiometries, VO₂ has received considerable attention due to its remarkable metal-insulator transition (MIT) behavior, which causes a significant reversible change in its electrical and optical properties occurring across the phase transition at 67°C. The initially amorphous VO₂ thin films were fabricated by the emerging, Atomic Layer Deposition (ALD) technique with (tetrakis[ethylmethylamino]vanadium) {V(NEtMe)₄} as precursor and H₂O vapor as oxidation agent. For benchmarking we have also used the RF Magnetron Sputtering technique to deposit metallic vanadium thin films, which were later oxidized during furnace annealing. Post annealing of …

Polarization Of Bi2te3 Thin Film In A Floating-Gate Capacitor Structure, Hui Yuan, Kai Zhang, Haitao Li, Hao Zhu, John E. Bonevich, Helmut Baumgart, Curt A. Richter, Qiliang Li

Electrical & Computer Engineering Faculty Publications

Metal-Oxide-Semiconductor (MOS) capacitors with Bi₂Te₃ thin film sandwiched and embedded inside the oxide layer have been fabricated and studied. The capacitors exhibit ferroelectric-like hysteresis which is a result of the robust, reversible polarization of the Bi₂Te₃ thin film while the gate voltage sweeps. The temperature-dependent capacitance measurement indicates that the activation energy is about 0.33 eV for separating the electron and hole pairs in the bulk of Bi₂Te₃, and driving them to either the top or bottom surface of the thin film. Because of the fast polarization speed, potentially excellent …

Corrosion Resistance Of Enamel Coating Modified By Calcium Silicate And Sand Particle For Steel Reinforcement In Concrete, Fujian Tang

Masters Theses

"Porcelain enamel has stable chemical property in harsh environments such as high temperature, acid and alkaline, and it can also chemically react with substrate reinforcing steel resulting in improved adherence strength. In this study, the corrosion resistances of enamel coating modified by calcium silicate and sand particles, which are designed for improved bond strength with surrounding concrete, were investigated in 3.5 wt% NaCl solution. It consists of two papers that describe the results of the study.

The first paper investigates the corrosion behavior of enamel coating modified by calcium silicate applied to reinforcing steel bar in 3.5 wt% NaCl solution …

Effect And Interactions Of Commercial Additives And Chloride Ion In Copper Electrowinning, Wenyuan Cui

Masters Theses

"This thesis is to understand and compare the effects and interactions of modified polysaccharide (HydroStar), polyacrylamide (Cyquest N-900) and chloride ion on copper electrowinning. A study of the nucleation and growth was conducted in a synthetic electrolyte (40 g/L Cu, 160 g/L H₂SO₄, 20 mg/L Cl-) with the addition of HydroStar or Cyquest N-900 using potential step measurements. The current responses generated were compared to theoretical models of nucleation and growth mechanisms. The nucleation and growth mechanism changed as function of potential and the presence of organic additives. The nucleation and growth mechanisms were confirmed using scanning electron microscopy (SEM). …

In-Situ Tem Plasma Chip Nanofabrication And Characterization, Xuebo Cui

Dissertations, Master's Theses and Master's Reports - Open

A silicon-based microcell was fabricated with the potential for use in in-situ transmission electron microscopy (TEM) of materials under plasma processing. The microcell consisted of 50 nm-thick film of silicon nitride observation window with 60μm distance between two electrodes. E-beam scattering Mont Carlo simulation showed that the silicon nitride thin film would have very low scattering effect on TEM primary electron beam accelerated at 200 keV. Only 4.7% of primary electrons were scattered by silicon nitride thin film and the Ar gas (60 μm thick at 1 atm pressure) filling the space between silicon nitride films. Theoretical calculation also showed …

Nano-Engineering Of Composite Material Via Reactive Mechanical Alloying/Milling (Rma/M), Edward Andrew Laitila

Dissertations, Master's Theses and Master's Reports - Open

Attempts to strengthen a chromium-modified titanium trialuminide by a combination of grain size refinement and dispersoid strengthening led to a new means to synthesize such materials. This Reactive Mechanical Alloying/Milling process uses in situ reactions between the metallic powders and elements from a process control agent and/or a gaseous environment to assemble a dispersed small hard particle phase within the matrix by a bottom-up approach. In the current research milled powders of the trialuminide alloy along with titanium carbide were produced. The amount of the carbide can be varied widely with simple processing changes and in this case the milling …

Development Of Practical Applications For Reprap Style 3-D Printers In Engineering, Benjamin T. Wittbrodt

Dissertations, Master's Theses and Master's Reports - Open

The current rise in popularity of consumer level 3-D printers introduces a need to understand the application and material property capabilities of the technology. Presented here is data demonstrating the ability for the average U.S. consumer to recuperate the cost of a 3-D printer within one year of ownership. Additionally, using a consumer level 3-D printer, multiple photovoltaic (PV) racking systems were printed and produced with much lower cost compared to commercially available aluminum racking. Additionally, mechanical testing on 3-D printed components showed a temperature dependence on both percent crystallinity and ultimate tensile strength. Conclusions are drawn using the information …

The Effects Of Layer Thickness On Dry-Sliding Wear Of Binder Jet Additively Manufactured Stainless Steel And Bronze Composite, Cody Ingenthron

All Graduate Theses, Dissertations, and Other Capstone Projects

Pin on disk wear testing was used to compare additively manufactured binder jet metal matrix composites. The process parameters were changed. The layer thickness and applied forces were varied for the experimental study. Three different layer thicknesses used were, 50μm, 100μm, and 200μm. The pin used was a 420 stainless pin. The wear characteristics of the disk were examined using pin-on-disc method. The material tested was a composite of 420 stainless steel, and 90-10 bronze. Samples were weighed before, during, and after the test to determine differences in mass. Wear tracks were examined using a Scanning Electron Microscope. The results …

Analysis Of The Influence Of Organic Corrosion Inhibitors On Corrosion Of Reinforcement In Concrete Bridge Structure Under Simulated Field Service Environment, Liang Shi, J. Ye, C. C. Chen, Y. Wu, J. Z. Liu

International Conference on Durability of Concrete Structures

For concrete bridge projects in marine environments, attention must be paid to the reinforcement corrosion problems caused by chloride intrusion. As kinds of functional admixtures, which can reduce the reinforcement corrosion rate, corrosion inhibitors are becoming very popular in China in new bridge projects. Corrosion inhibitors cover both inorganic and organic inhibitors. Nitrite is representative of inorganic corrosion inhibitors, but its carcinogenicity has hindered its further development. Organic corrosion inhibitors such as small-molecule-based alcohol amine series are becoming the focus of attention. To guide the scientific applications of organic corrosion inhibitors, China is carrying out broad applications technology research. But …

Processing And Characterization Of Continuous Basalt Fiber Reinforced Ceramic Matrix Composites Using Polymer Derived Ceramics, Sarah Cox

Electronic Theses and Dissertations

The need for high performance vehicles in the aerospace industry requires materials which can withstand high loads and high temperatures. New developments in launch pads and infrastructure must also be made to handle this intense environment with lightweight, reusable, structural materials. By using more functional materials, better performance can be seen in the launch environment, and launch vehicle designs which have not been previously used can be considered. The development of high temperature structural composite materials has been very limited due to the high cost of the materials and the processing needed. Polymer matrix composites can be used for temperatures …

Non-Oxide Porous Ceramics From Polymer Precursor, Xueping Yang

Electronic Theses and Dissertations

Non-oxide porous ceramics exhibit many unique and superior properties, such as better high-temperature stability, improved chemical inertness/corrosive resistance, as well as wide band-gap semiconducting behavior, which lead to numerous potential applications in catalysis, high temperature electronic and photonic devices, and micro-electromechanical systems. Currently, most mesoporous non-oxide ceramics (e.g. SiC) are formed by two-step templating methods, which are hard to adjust the pore sizes, and require a harmful etching step or a high temperature treatment to remove the templates. In this dissertation, we report a novel technique for synthesizing hierarchically mesoporous non-oxide SiC ceramic from a block copolymer precursor. The copolymer …

Freeze Thaw Durability Of Internally Cured Concrete Made Using Superabsorbent Polymers, Wesley A. Jones, W. Jason Weiss

International Conference on Durability of Concrete Structures

The use of superabsorbent polymers (SAPs) to produce internally cured concrete has been shown to be effective in reducing the potential for restrained shrinkage cracking of high performance concrete mixtures. However, not much is known regarding the freeze–thaw durability of concrete mixtures that incorporate SAPs for internal curing (IC). When SAP particles desorb (or partially desorb) the “water” (pore fluid) they contain for the purposes of IC, some believe that the void space created by these particles can provide enough empty voids to accommodate the additional volume caused by water expansion upon freezing. This paper investigates the freeze–thaw durability of …

Influence Of Organic Inhibitor On Corrosion Resistance Of Steel In Simulated Concrete Pore Solution, Jingshun S. Cai, C. C. Chen, J. Z. Liu, J. P. Liu

International Conference on Durability of Concrete Structures

Organic corrosion inhibitor is one of lower cost technologies that limit the deterioration of concrete structures. The influence of a newly prepared organic corrosion inhibitor on the corrosion behavior of carbon steel in simulated concrete pore solution was investigated by polarization curves, electrochemical impedance spectroscopy, and so on. The effect of organic corrosion inhibitors on concrete working performance was also studied. The results show that the corrosion rate decreases with the concentration of inhibitor increase; when the content of inhibitor up to 1.5% versus water, the oxide film was completely passive. Organic corrosion inhibitor had no effect on work performance.

Co2 Sequestration In Cement-Based Materials During Mixing Process Using Carbonated Water And Gaseous Co2, Jacek Kwasny, P. A. Muhammed Basheer, Mark I. Russell, William Doherty, Kieran Owens, Neil Ward

International Conference on Durability of Concrete Structures

This paper presents selected findings from a recently completed research project, aimed at the investigation of CO₂ sequestration in cement-based materials during the early stages of hydration when the cement paste is being mixed. Portland cement pastes were carbonated during the mixing process, using both carbonated water and gaseous CO₂, and their properties were compared to the control non-carbonated mix. All mixes were prepared in a purpose-designed chamber that permitted carbonated water and gaseous CO₂ to be mixed with the cementbased materials during the mixing process, without losses of CO₂ to the external environment. Temperature …

Atomic Layer Deposition, Paul Kubicza

Summer Community of Scholars Posters (RCEU and HCR Combined Programs)

No abstract provided.

Effect Of Er Doping On The Structural And Magnetic Properties Of Cobalt-Ferrite, Sateesh Prathapani, M. Vinitha, Tanjore V. Jayaraman, D. Das

Department of Mechanical and Materials Engineering: Faculty Publications

Nanocrystalline particulates of Er doped cobalt-ferrites CoFe_(2–x)Er_xO₄ (0 ≤ x ≤ 0.04), were synthesized, using sol-gel assisted autocombustion method. Co-, Fe-, and Er- nitrates were the oxidizers, and malic acid served as a fuel and chelating agent. Calcination (400–600 °C for 4h) of the precursor powders was followed by sintering (1000 °C for 4 h) and structural and magnetic characterization. X-ray diffraction confirmed the formation of single phase of spinel for the compositions x = 0, 0.01, and 0.02; and for higher compositions an additional orthoferrite phase formed along with the spinel phase. …

Practical Aspects Of Modern And Future Permanent Magnets, R.W. Mccallum, L. H. Lewis, Ralph Skomski, M. J. Kramer, I. E. Anderson

Ralph Skomski Publications

The mandate to reduce greenhouse gases will require highly efficient electric machines for both power generation and traction motor applications. Although permanent magnet electric machines utilizing Nd2Fe14B-based magnets provide obvious power-to-weight advantages over induction machines, the limited availability and high price of the rare earth (RE) metals make these machines less favorable. Of particular concern is the cost and supply criticality of Dy, a key RE element that is required to improve the high-temperature performance of Nd-based magnetic alloys for use in generators and traction motors. Alternatives to RE-based alloys do exist, but they currently lack the energy density necessary …

Organic Ferroelectric Evaporator With Substrate Cooling And In Situ Transport Capabilities, Keith Foreman, C. Labedz, M. Shearer, Shireen Adenwalla

Shireen Adenwalla Papers

We report on the design, operation, and performance of a thermal evaporation chamber capable of evaporating organic thin films. Organic thin films are employed in a diverse range of devices and can provide insight into fundamental physical phenomena. However, growing organic thin films is often challenging and requires very specific deposition parameters. The chamber presented here is capable of cooling sample substrates to temperatures below 130 K and allows for the detachment of the sample from the cooling stage and in situ transport. This permits the use of multiple deposition techniques in separate, but connected, deposition chambers without breaking vacuum …

Correlation Between The Microstructure And Mechanical Properties Of Irradiated Fe-9cr Ods, M. Swenson, C. Dolph, J. Wharry

Materials Science and Engineering Faculty Publications and Presentations

The growing global demand for energy will increasingly call upon fusion reactors and Generation IV nuclear fission reactors to supply safe and reliable energy worldwide. Ferritic/martensitic (F/M) alloys are leading candidates for structural components in these reactors because of their high strength, dimensional stability, and low activation. In novel reactor concepts, these materials will be subject to extreme operating conditions, accumulating doses of irradiation up to a few hundred displacements per atom (dpa) at temperatures as high as 600°C. Oxide dispersion strengthened (ODS) F/M alloys containing a dispersion of Y-Ti-0 nanoclusters have been developed to operate at even higher temperatures.

Mechanical And Transport Properties Of Alkali-Activated Natural Pozzolans As Sustainable Binders, Brittany Radke

Calvert Undergraduate Research Awards

OPC production accounts for 5 to 7% of the global carbon dioxide (CO₂) emissions, contributing to global warming. The desire to reduce CO₂ emissions and produce more durable concrete has given impetus to search for new binders. It is suggested that alkali-activated natural pozzolans have the potential for use as a sustainable replacement for OPC in concrete.

The current study presented herein evaluated fresh, mechanical, and transport properties of alkali-activated natural pozzolan mortars containing various concentrations of sodium hydroxide solutions as an alkaline activator. To this aim, alkali-activated natural pozzolan mortars were made with concentrations of sodium …

Microwave Absorption Properties Of Tires, Yuzhe Zhang

Dissertations, Master's Theses and Master's Reports - Open

The waste tire is belonging to insoluble high polymer elastic materials. It takes hundreds of years to resolve the macromolecules of waste tire into the standard which does not pollute the environment. More and more waste tires are air stored which causes space occupation and mosquito-breeding in the places that will spread diseases. The disposal methods include landfill, stockpiles, dumping and incising into particles. However, all these methods are not technically and economically efficient. The trend for the development of waste tire treatment processes is low cost, on-site, and high product recovery at high energy efficiency. In this project, microwave …

Mse Annual Report 2014, Department Of Materials Science And Engineering, Michigan Technological University

Department of Materials Science and Engineering Annual Reports

Table of Contents

• Department Legends
• Wonder Material
• Student News
• Faculty and Staff News
• Alumni News
• Endowed Scholarships

Joining And Hermetic Sealing Of Silicon Carbide Using Iron, Chromium, And Aluminum Alloys, Andrew Morgan

Theses and Dissertations

Silicon Carbide (SiC) is increasingly gaining attention as a potential fuel cladding material, on account of its favorable thermo-mechanical and neutronic properties. The major limitations of such a cladding is currently associated with joining and hermetic sealing. The work presented here investigated the use of Al, Cr and Fe metals and a specialized alloy (FeCrAl) to achieve hermetic sealing of SiC tubes as well as a joining technology of SiC. Major part of solving this issue requires addressing joining of ceramic and metallic components, which are largely dissimilar in both thermal and mechanical properties. Preliminary experiments to bond SiC with …