Engineering Commons^™

Australian Tractor Test Report No. 55 : Nuffield 4/65, G H. Vasey, W. F. Baillie

Journal of the Department of Agriculture, Western Australia, Series 4

THE Nuffield 4/65 is a general purpose farm tractor of 49 drawbar horsepower.

With 54 h.p. at the P.T.O. at rated engine speed it comes within Class 5 of the Australian Standard Classification of Wheeled Tractors for Agricultural Purposes, AS D10-1967. I t is equipped with 18.4 x 30 pneumatic tyres.

It has a five speed gear box with a High and Low ratio change giving 10 forward and 2 reverse speeds.

Vibration Of An Internally Damped Tapered Truncated Cantilever Beam, Chimanbhai Magandas Patel

Masters Theses

"This thesis provides a vibration analysis of an internally damped, tapered, truncated, cantilever beam. Using two formulations of the problem based on: (1) Discrete mass and (2) continuous mass distribution, solutions are given for a beam having square cross section with linear depth and linear width variation. A Kelvin viscoelastic material for the beam is assumed. The vibration of the beam is considered to produce plane stress in the material, and the stress-strain relationship is applied only to the strain in the plane of bending. An exact solution for frequency of oscillation, mode shape, and steady state response is obtained …

Concrete In Dairies, D Roger Buchanan

Journal of the Department of Agriculture, Western Australia, Series 4

PRIME requirements for exposed concrete surfaces in dairies are that they should be easily cleansed and should not deteriorate in contact with milk and milk products.

In milking stalls, animal races and on loading platforms hardwearing surfaces which offer good foothold are also necessary.

Australian Tractor Test Report No. 49 : Mccormick International 624, G H. Vasey, W. F. Baillie

Journal of the Department of Agriculture, Western Australia, Series 4

AUSTRALIAN TRACTOR TEST REPORT

No. 49 - McCORMICK INTERNATIONAL 624

A Numerical (Matrix) Solution For The Vibration Frequencies And Modes Of A Nonuniform Rectangular Plate With Arbitrary Edge Conditions, F. David Utterback

Masters Theses

"The material presented in this thesis is designed to provide the practicing engineer with a practical, approximate method of solution for the increasingly important problem of plate vibrations. The technique presented herein is basically an application of the use of generalized coordinates to describe the elastic and inertial properties of a finite element representation of a nonuniform rectangular plate. The plate will be idealized by utilizing a modification of the grid work technique developed by Hrennifkoff as a lattice work of interconnecting beams. By employing the elastic displacements as generalized coordinates, the only required compatibility conditions are that the displacements …

Effects Of Pressure On The Mechanical Properties Of Magnesium, Joseph George Hoeg

Masters Theses

"The data collected in an attempt to evaluate the pressure dependency of the mechanical properties of extruded AZ31B-F magnesium alloy are presented herein. This information was compiled from the results of compression tests run in hydraulic fluid environments pressurized to 50,000 psi, and tension tests run in the atmosphere. Specimen axial load and longitudinal strain were recorded and converted to effective stress and effective strain parameters for presentation. The term pressure is defined, in this report, as the negative average of the principal stresses or, essentially, the negative of the hydrostatic component of stress. The effective stress and strain, at …

An Analysis Of Dirac Delta Generated Spherical Waves In An Infinite Maxwell Medium, William F. Breig

Masters Theses

"It is an accepted fact that the simple Maxwell and Voigt models do not usually represent the behavior of real materials. In order to make the results of a model more realistic, other combinations of springs and dashpots must be considered. To understand the more complicated models, it is desirable to have a knowledge of the Maxwell model since this element usually occurs either in series or in parallel in the advanced models. This investigation reports solutions of the spherical wave equation in both the elastic and viscoelastic media. Laplace transform techniques are used to obtain the parameters; stress, velocity, …

Noise In Cadmium Sulfide & Cadmium Selenide Photoconductive Cells, Edward Foster

Masters Theses & Specialist Projects

The primary object of this investigation is to design a system, including equipment and procedures, that can be used to evaluate the noise characteristics of photoconductive cells. The data once collected must be in a comprehensive and useful form. The secondary object is to use this system to evaluate a large number of cells of various types and to compare their noise profiles in a manner such that definite conclusions can be drawn concerning the absolute noise levels and profiles generated by the various cell types and the relations that may exist between the cells' noise output and the way …

Collision And Pursuit Course Terminal Closures For Spacecraft To Satellite Rendezvous, John Anthony Campbell

Masters Theses

"Collision and pursuit course closure maneuvers were studied for correcting position and velocity errors in the terminal phase of spacecraft to satellite rendezvous.

Minimum values of the ratio of initial range to velocity necessary to achieve rendezvous were determined for collision closures as a function of the initial line of sight. The time and velocity increment required for rendezvous were computed as a function of initial conditions.

Pursuit closure maneuvers were analyzed and time and velocity increments defined as a function of initial range, closing velocity, line of sight angle and angular velocity.

The velocity increments required were significantly higher …

Controlled Environment Broiler Houses In Western Australia, D F. Hessels

Journal of the Department of Agriculture, Western Australia, Series 4

The three main features which contribute to the better returns from controlled environment broiler housing are higher density, better conversion and a reduction in labour.

The higher initial cost of housing and higher running costs are more than covered by these three advantages.

Plastic Deformation Of Thin Plates With A Spherical Indenter, Benjamin Jen-An Chang

Masters Theses

"A method of determining the stress distribution in a thin plate deformed with a spherical indenter is presented in this report. The analysis is formulated in cylindrical coordinates and utilizes the basic principles of plasticity (von Mises yield criteria, Luwig stress-strain equation, Hencky Deformation theory, etc.). The problem is solved through the utility of a displacement function that, by virtue of its definition, automatically assures that the condition of volume constancy is satisfied. The boundary conditions are selected on the basis of having average, or integrated, effects corresponding to the physical constraints of the problem. Numerical integration is introduced to …

Dynamic Response Of A Simply Supported Beam To An Accelerating Point Load, Joseph Victor Cusumano

Masters Theses

"An analysis based on linear theory is presented for determining the dynamic response of a simply supported beam on an elastic foundation acted upon by a moving time dependent point force with axial forces included. This thesis extends the present theory to include an analysis of a point force accelerating uniformly across the beam. In particular, it is shown that the customary resonance conditions which are prevalent for a point force moving with uniform velocity no longer exist for the case of a point force accelerating uniformly across the beam.

The basic problem and its solution are presented for a …

Stresses In A Thick Spherical Shell, David Wayne Moore

Masters Theses

"This thesis reports a method to evaluate the stresses in a segment of a thick spherical shell. In the numerical examples loads due to thermal expansion as the shell is constrained at the free edge and a dead load acting vertically downward were considered for a shell assumed pinned but free to rotate and for a shell assumed completely fixed at the edge. A concrete shell was specifically studied but the method would also apply to a shell of any homogeneous, isotropic material"--Abstract, page i.

A Plastic Stress Analysis Of Cylindrical Wafers Under Elastically Deformable Compression Plates, Robert L. Davis, J. W. Jackson

Mechanical and Aerospace Engineering Faculty Research & Creative Works

This paper represents an analysis of the pressure distribution occurring in axially loaded cylindrical wafers with, and without, elastic radial constraints. The purpose of this report is to demonstrate the resulting stress patterns that occur in short compression specimens frequently used in determining material properties, and in the opposed-anvil, or Bridgman-type, high-pressure cells. The influence of radial constraints, material strain hardening, wafer diameter-to-height ratio, anvil or plate deflection, and the wafer-anvil interface friction on the resulting stress distributions have been examined. The integrated normal stress distribution across the specimen surface has been verified experimentally via numerous tests in which each …

Dynamic Response Of Plates Due To Moving Loads, Theodore F. Raske, Alois L. Schlack

Mechanical and Aerospace Engineering Faculty Research & Creative Works

An analysis based on linear theory is presented for determining the dynamic response and the conditions of resonance for a simply supported rectangular plate acted upon by two types of moving loads corresponding to: (1) a point force of variable magnitude oscillating about a fixed position on the plate, and (2) a point force of constant magnitude traveling in a circular orbit about a fixed position on the plate. In addition to the ordinary resonance as produced by a variable magnitude load concentrated at a fixed position on the plate, resonance of the plate may occur due to the changing …

A Photoelastic Study Of The Stresses In A Deep Beam Using Partial Mirrors For Isochromatic Fringe Sharpening And Fringe Multiplication, Edward M. Raney

Masters Theses

"This paper is a photoelastic investigation of the stresses in a deep beam using partial mirrors to obtain isocromatic fringe sharpening and fringe multiplication. This method may be of particular value in photoelastic work for obtaining full field fringe multiplication and fringe sharpening for models which exhibit low fringe orders.

The photoelastic model used in this investigation is a deep beam with a length to depth ratio of one. A uniform load is applied over the center one-half of the beam. The beam is supported by two uniform loads distributed over a length of one-quarter the span.

A first approximation …

Modal Characteristics Of A Vibrating Truss, Edd Leighman Ghent Jr.

Masters Theses

"In this thesis, a complete technique is presented for the vibration analysis of any planar structure which can be classified in the broad category of trusses or frames. Although a theoretical backdrop is included for the' sake of completeness, the intent is to provide a technique that is readily adapted to computer usage and can be handled with a minimum of confusion or misunderstanding.

The problem is solved by the use of a displacement technique wherein the inertia and stiffness properties of a structure are calculated by superimposing the contributions of each component of the structure. The calculation of these …

The Effect Of Combined Torsional And Bending Loads On A Channel Beam With One End Restrained From Warping, David M. Schaeffer

Masters Theses

"Channel beams have been designed with the main purpose of giving large resistance to bending while the torsional strengths are known to be relatively small. In this experiment, a cantilevered channel beam was loaded with a concentrated load at the free end, first through the experimentally determined shear center and then through the centroid of the cross section. For each loading condition, the strains were measured with the aid of SR-4 strain gages placed at intervals along the length of the beam. With the aid of a computer, the strains were converted into longitudinal stresses and these stresses were compared …

Comparison Of Plastic Stress-Strain Material Properties As Determined From Conventional Experiments, Wen Mo Chen

Masters Theses

"In problems of engineering design, it is usually assumed that the stress-strain diagrams of a given material, as obtained from different loading conditions, are the same. In fact, by using the classical theory of plasticity, it can be shown that, with an appropriate selection of stress and strain related parameters, the diagrams should coincide.

Three different materials - magnesium, aluminum and steel, have been tested under tension, compression, torsion and bending loads. Stress-strain diagrams were constructed from these observations. This thesis presents an analysis of the relative agreement between the theoretical and experimental results of these materials"--Abstract, page i.

Siphon Tubes For Furrow Irrigation In The Kimberleys, K S. Cole

Journal of the Department of Agriculture, Western Australia, Series 4

Irrigation soils in the Ord River area have a high clay content and erode easily under the influence of running water.

To overcome the problem of erosion in cuts between the head channels and irrigation furrows polythene siphon tubes have been found the most satisfactory.

In this article K. S. Cole, B.Sc. (Agric), Agricultural Adviser, Kununurra, describes the use of siphon tubes for furrow irrigation in the Kimberleys.

Plan For Quality In Silage, Department Of Agriculture, Western Australia

Journal of the Department of Agriculture, Western Australia, Series 4

SILAGE making time is fast approaching in the South-West.

Last minute preparations before harvesting will help avoid delays at the time of making this valuable fodder, thereby reducing the amount of costly spoilage caused by hold-ups.

Its Shearing Time, Department Of Agriculture, Western Australia

Journal of the Department of Agriculture, Western Australia, Series 4

SHEARING will soon be taking place on your property. For a smooth annual wool harvest, remember:—

Blasting. Part 1. Explosives And The Farmer, G A. Greaves

Journal of the Department of Agriculture, Western Australia, Series 4

ABOUT 3,000 tons of commercial blasting explosives of various types are used every year in Western Australia of which approximately two thirds is utilised by mining industries and the remainder goes mainly to quarrying and public works.

The farmer and orchardist actually use only very small amounts but nevertheless explosives are a very useful working tool for the primary producer.

Blasting. Part 2. Explosives On The Farm, G A. Greaves

Journal of the Department of Agriculture, Western Australia, Series 4

EXPLOSIVES will function with maximum reliability and efficiency only when they are carefully stored under cool, dry conditions so as to avoid deterioration.

When preparing charges the user should follow a correct procedure and use the proper tools. Always treat explosives with respect and remember they are made to explode. When they hit they hit hard.

A Study Of The Flow Characteristics In The Core Region Of The Sandia Engineering Reactor, James A. Moeller

Chemical and Biological Engineering ETDs

The core region of a nuclear rector is an extremely compact area with a capability of providing a very high heat output. Regardless of the type of coolant used, the heat transfer characteristics of this region must be adequately designed to prevent any undesirable "hot-spots" from developing. The Sandia Engineering Reactor has one of the most compact cores of any in currently operating nuclear reactors. For this reason it is necessary to investigate fully the heat transfer characteristics of the core. The rate of heat transfer from the fuel elements to the coolant is directly dependent upon the temperature difference …

Australian Spark Arrester Tests : Spark Arrester For International B-250, W. F. Baillie, G. H. Vasey

Journal of the Department of Agriculture, Western Australia, Series 4

FORMAL tests on spark arresters are conducted by The Tractor Testing Committee at the Testing Station, Werribee, on behalf of those companies concerned with tractors, engines or spark arresters who wish to have these equipments tested.

Australian Spark Arrester Tests : Spark Arrester For Fordson Dexta, W. F. Baillie, G. H. Vasey

Journal of the Department of Agriculture, Western Australia, Series 4

FORMAL tests on spark arresters are conducted by The Tractor Testing Committee at the Testing Station, Werribee, on behalf of those Companies concerned with tractors, engines or spark arresters who wish to have these equipments tested.

The arrester is tested on the engine for which it is especially designed or if this is not convenient, it is tested on an engine having the characteristics and power for which the spark arrester is intended.

Test Of High-Speed Engine, William Frazier Owen

Student and Lippitt Prize Essays

Discusses the best ways in which a steam engine can function by using measurements from an actual steam engine. The essay ultimately determines that a steam engine is at its highest efficiency when carrying the largest load possible.

Jackscrews, Albert Lewis Kenyon

Student and Lippitt Prize Essays

Definition, development, and description of the jackscrew, a device for the application of the screw to the moving of heavy weights.