Engineering Commons^™

Mechanics Of Pure Bending And Eccentric Buckling In High-Strain Composite Structures, Jimesh D. Bhagatji, Oleksandr G. Kravchenko, Sharanabasaweshwara Asundi

Mechanical & Aerospace Engineering Faculty Publications

To maximize the capabilities of nano- and micro-class satellites, which are limited by their size, weight, and power, advancements in deployable mechanisms with a high deployable surface area to packaging volume ratio are necessary. Without progress in understanding the mechanics of high-strain materials and structures, the development of compact deployable mechanisms for this class of satellites would be difficult. This paper presents fabrication, experimental testing, and progressive failure modeling to study the deformation of an ultra-thin composite beam. The research study examines the deformation modes of a post-deployed boom under repetitive pure bending loads using a four-point bending setup and …

Switching Methods For Three-Dimensional Rotational Dynamics Using Modified Rodrigues Parameters, Matthew Jarrett Banks

Mechanical & Aerospace Engineering Theses & Dissertations

A rigid body in space has three degrees of rotational freedom. As a result, a minimum of three independent parameters is required to define the three-dimensional orientation of a rigid body. As is well known, every set of three independent parameters has at least one orientation where mathematical or geometrical singularities are encountered; therefore, when the use of a three-parameter representation is desired, a method for singularity avoidance must also be considered. A common practice for singularity avoidance is to switch between parameter sets whose singularities occur at different orientations. With this in mind, modified Rodrigues parameters (MRP) are considered …

Development, Experimental Validation, And Progressive Failure Modeling Of An Ultra-Thin High Stiffness Deployable Composite Boom For In-Space Applications, Jimesh D. Bhagatji

Mechanical & Aerospace Engineering Theses & Dissertations

To maximize the capabilities of nano- and micro-class satellites, which are limited by their size, weight, and power, advancements in deployable mechanisms with a high deployable surface area to packaging volume ratio are necessary. Without progress in understanding the mechanics of high-strain materials and structures, the development of compact deployable mechanisms for this class of satellites would be difficult. This research focuses on fabrication, experimental testing, and progressive failure modelling to study the deformation of an ultra-thin composite beam. The research study examines deformation modes of a boom under repetitive pure bending loads using 4-point bending setup. The material and …

Cold-Formed Steel Strength Predictions For Combined Bending And Torsion, Yu Xia, Robert S. Glauz, Benjamin W. Schafer, Michael Seek, Hannah B. Blum

Engineering Technology Faculty Publications

Locally slender cross-section members, such as cold-formed steel Cee and Zee sections, are susceptible to significant twisting and high warping torsion stresses. Torsion considerations are complicated by whether it is derived as a first-order effect from loading or a second-order effect from instability. The current design for combined bending and torsion interaction has some limitations, including only considering the first yield in torsion and ignoring the cross-section slenderness in torsion. Previous work has derived a simple uniform equation to predict the bimoment capacity and two bimoment strength curves for local and distortional buckling under torsion only. This work is extended …

Pinch Force Generation During Scaling By Dental Professionals: A Systematic Review, Jessica R. Suedbeck, Emily A. Ludwig

Dental Hygiene Faculty Publications

Objective

The objective of this review was to examine the impact of instrument designs on pinch force generation during scaling by dental professionals.

Methods

Three databases were utilized from September 2019 to November 2021 in addition to hand-searching specific journals and reference lists. Research articles that examined pinch force generation in dental professionals during scaling with manual instruments only were included. Bias was assessed in the individual articles.

Results

Six research articles were included with sample populations that varied from 12 to 24 participants. Four articles evaluated instrument designs in relation to pinch force generation during scaling by dental professionals. …

Effect Of Platelet Length And Stochastic Morphology On Flexural Behavior Of Prepreg Platelet Molded Composites, Siavash Sattar, Benjamin Beltran Laredo, Sergii G. Kravchenko, Oleksandr G. Kravchenko

Mechanical & Aerospace Engineering Faculty Publications

Prepreg platelet molding compound (PPMC) can be used to create structural grade material with a heterogeneous mesoscale morphology. The present work considered various platelet lengths of the prepreg system IM7/8552 to study the effect of platelet length on the flexural behavior of PPMC composite. A progressive failure finite-element analysis was used to understand competing failure modes in PPMC with the different platelet length. The interlaminar and in-plane damage mechanisms were employed to describe complex failure modes within the mesostructure of PPMCs. Experimental results of the flexural tests of the PPMC with different platelet length sizes were used to validate the …

Elastic Properties Of The Non-Mixing Copper Donor Assisted Material In Friction Stir Welding Of Aluminum Alloys Using Nanoindentation, M. Ojha, A. H. Al-Allaq, Y. S. Mohammed, S. N. Bhukya, Z. Wu, A. A. Elmustafa

Mechanical & Aerospace Engineering Faculty Publications

Friction stir welding of high-strength materials such as steels is the impeded by the lack of the vast heat input needed to start the process. Contact friction is considered the most dominant source of heat generation for FSW steels which tends to cause severe wear conditions of the tool hear. To relieve the extreme wear conditions that occur on the tool heads because of FSW steels, we introduce the non-mixing Cu donor stir material to friction stir welding of aluminum alloys. The elastic properties of the Cu donor assisted friction stir welded aluminum alloys are measured using nanoindentation. The hardness …

Post-Weld Heat Treatment Effects On Microstructure, Crystal Structure, And Mechanical Properties Of Donor Stir–Assisted Friction Stir Welding Material Of Aa6061-T6 Alloy, Aiman H. Al-Allaq, Manish Ojha, Yousuf S. Mohammed, Srinivasa N. Bhukya, Zhenhua Wu, Abdelmageed A. Elmustafa

Mechanical & Aerospace Engineering Faculty Publications

Friction stir welding (FSW) technology combines heat input from friction and extreme plastic deformation to produce high-quality joints in aluminum and other alloy systems. This necessitates examining the final welded joint’s mechanical and structural properties. Post-weld heat-treated AA6061-T6 alloy that resulted from the application of a Cu donor stir–assisted (CDSA) friction stir welding (FSW) material was examined for crystal structure and mechanical properties. CDSA FSW samples were tested at a constant tool rotational speed of 1400 rpm and a welding translational speed of 1 mm/s. CDSA samples of 20% and 60% thickness of the AA6061-T6 base alloy were selected to …

Influence Of Defects On In-Plane Dynamic Properties Of Hexagonal Ligament Chiral Structures, Ning An, Xunwen Su, Dongmei Zhu, Mileta M. Tomovic

Engineering Technology Faculty Publications

Although the six-ligament chiral structure has many unique properties, due to its special structure, the stress concentration is prone to defects. In addition, additive manufacturing is also prone to defects. This paper studies the effect of defects, which is helpful for the better application of the six-ligament chiral structure. Several new six-ligament chiral structures with random and concentrated defects were designed to explore the effects of the defects on the in-plane dynamic properties. The structures were studied with the finite element ANSYS/LSDYNA numerical simulation and experimental methods. According to the defect-free six-ligament chiral structures exhibiting different deformation modes at different …

Lateral-Torsional Instability And Biaxial Bending Of Imperfect Frp I-Beams, Jodi Knorowski, Stella B. Bondi, Zia Razzaq

Civil & Environmental Engineering Faculty Publications

This paper presents the outcome of a theoretical and experimental study of the behavior of Fiber Reinforced Polymer (FRP) I-beams exposed to lateral-torsional instability or when subjected to biaxial bending. Laboratory experiments involved the application of vertical and horizontal static loads to a 4 x 4 x ¼ in. I-beam with various lengths and the resulting deflections were recorded. Governing biaxial flexure and torsion differential equations were modified to account for the presence of initial imperfections and subsequently solved using a central finite-difference scheme. The theoretical predictions of the beam behavior were found to be in good agreement with what …

Method For Reducing Warping Stresses In Torsionally Loaded I-Section Members Using Cfrp Plates, Mamadou Konate, Zia Razzaq

Civil & Environmental Engineering Faculty Publications

This paper presents a method for reducing warping normal stresses in torsionally loaded I-section members by utilizing carbon fiber-reinforced polymer (CFRP) plates. The CFRP plates are bonded to the outer surfaces of the flanges with a view to reducing warping normal stresses. The maximum warping normal stress in the flanges of a steel I-shaped member without the CFRP plates is compared to those obtained with the CFRP plates having various thicknesses. It has been found that the use of CFRP plates bonded to both flanges of the I-section result in a substantial reduction of the warping stresses. For the study …

Cold-Formed Steel Strength Predictions For Torsion, Yu Xia, Robert S. Glauz, Benjamin W. Schafer, Michael Seek, Hannah B. Blum

Engineering Technology Faculty Publications

Locally slender open cross-section members are susceptible to significant twisting and high warping torsion stresses. Torsion considerations are complicated by whether it is derived as a first-order effect from loading or a second-order effect from instability. Previous direct torsion experiments on lipped channels have shown significant inelastic reserve in limited cases. The current design for combined bending and torsion interaction has some limitations, including only considering the first yield in torsion and ignoring the cross-section slenderness in torsion. A parametric study is conducted to predict the torsion capacity in locally slender cross-sections. Shell finite element models of lipped Cee and …

Exploring The Effects Of Chip Flexibility On The Behavior Of Standing Seam Diaphragms To Brace Cold Formed Steel Purlins, Michael W. Seek

Engineering Technology Faculty Publications

Cold-formed steel C- and Z-shaped purlins in standing seam roof systems rely on the diaphragm action provided by the panels to restrain lateral movements and thus increase the load carrying capacity the purlins. The clip connection between the purlin and the panel has inherent and sometimes intentional flexibility designed to accommodate thermal deformations. The lateral deformation behavior of standing seam systems supported by Zees is highly nonlinear and this behavior is not well understood. The flexibility has major implications on the transfer of diaphragm forces throughout these systems and simplified models often grossly overpredict the demands on the diaphragm and …

Nb₃Sn Coating Of A 2.6 Ghz Srf Cavity By Sputter Deposition Technique, M. S. Shakel, Wei Cao, H. Elsayed-Ali, G. V. Eremeev, U. Pudasaini, A. M. Valente-Feliciano

Electrical & Computer Engineering Faculty Publications

Nb₃Sn is of interest as a coating for SRF cavities due to its higher transition temperature Tc ~18.3 K and superheating field Hsh ~400 mT, both are twice that of Nb. Nb₃Sn coated cavities can achieve high-quality factors at 4 K and can replace the bulk Nb cavities operated at 2 K. A cylindrical magnetron sputtering system was built, commissioned, and used to deposit Nb₃Sn on the inner surface of a 2.6 GHz single-cell Nb cavity. With two identical cylindrical magnetrons, this system can coat a cavity with high symmetry and uniform thickness. Using Nb-Sn multilayer sequential sputtering followed by …

Fluid-Wall Interactions In Pseudopotential Lattice Boltzmann Models, Cheng Peng, Luis F. Ayala, Orlando M. Ayala

Engineering Technology Faculty Publications

Designing proper fluid-wall interaction forces to achieve proper wetting conditions is an important area of interest in pseudopotential lattice Boltzmann models. In this paper, we propose a modified fluid-wall interaction force that applies for pseudopotential models of both single-component fluids and partially miscible multicomponent fluids, such as hydrocarbon mixtures. A reliable correlation that predicts the resulting liquid contact angle on a flat solid surface is also proposed. This correlation works well over a wide variety of pseudopotential lattice Boltzmann models and thermodynamic conditions.

Lateral Bracing Of Beams Provided By Standing Seam Roof System: Concepts And Case Study, Gengrui Wei, Benjamin Schafer, Michael Seek, Matthew Eatherton

Engineering Technology Faculty Publications

The standing seam roof (SSR) system is the most commonly used roof system for metal buildings due to its superior durability, water tightness, and energy efficiency. In this type of system, SSR panels attach to Z-shaped or C-shaped purlins with clips, and the purlins are in turn connected to rafters (i.e. roof beams). For the design of metal building rafters against lateral torsional buckling, bottom flange braces provide torsional bracing to the rafter and the SSR system provides some lateral bracing. However, the degree to which the SSR system can restrain the rafter against lateral movement has not previously been …

Nonhydrostatic Modeling Of Flow Interactions With Highly Flexible Vegetation, Navid Tahvildari, Ramin Familkhalili, Gangfeng Ma

Civil & Environmental Engineering Faculty Publications

Improving our understanding of the interactions between gravity waves, currents, and coastal vegetation, which are nonlinear in nature, enables coastal engineers and managers to better estimate hydrodynamic forces on coastal infrastructure and utilize natural elements to mitigate their impacts. Aquatic vegetation is ubiquitous in coastal waters and it is well-known that flow loses energy over vegetation. Computational modeling of wave-vegetation interaction has been the subject of numerous recent studies and many improvements have been achieved in reducing limitations applied on wave and vegetation behavior in these models. Mechanisms for highly flexible vegetation have been incorporated in a Boussinesq-type model and …

Attainment Of Rigorous Thermodynamic Consistency And Surface Tension In Single-Component Pseudopotential Lattice Boltzmann Models Via A Customized Equation Of State, Cheng Peng, Luis F. Ayala, Zhicheng Wang, Orlando M. Ayala

Engineering Technology Faculty Publications

The lack of thermodynamic consistency is a well-recognized problem in the single-component pseudopotential lattice Boltzmann models which prevents them from replicating accurate liquid and vapor phase densities; i.e., current models remain unable to exactly match coexisting density values predicted by the associated thermodynamic model. Most of the previous efforts had attempted to solve this problem by introducing tuning parameters, whose determination required empirical trial and error until acceptable thermodynamic consistency was achieved. In this study, we show that the problem can be alternatively solved by properly designing customized equations of state (EOSs) that replace any cubic EOS of choice during …

Superconductivity In La₂Ni₂In, Jannis Maiwald, Igor I. Mazin, Alex Gurevich, Meigan Aronson

Physics Faculty Publications

We report here the properties of single crystals of La₂Ni₂In. Electrical resistivity and specific heat measurements concur with the results of density functional theory calculations, finding that La₂Ni₂In is a weakly correlated metal, where the Ni magnetism is almost completely quenched, leaving only a weak Stoner enhancement of the density of states. Superconductivity is observed at temperatures below 0.9 K. A detailed analysis of the field and temperature dependencies of the resistivity, magnetic susceptibility, and specific heat at the lowest temperatures reveals that La₂Ni₂In is a dirty type-II …

Reliability Estimation Of Reciprocating Seals Based On Multivariate Dependence Analysis And It's Experimental Validation, Chao Zhang, Rentong Chen, Shaoping Wang, Yujie Qian, Mileta M. Tomovic

Engineering Technology Faculty Publications

Accurate reliability estimation for reciprocating seals is of great significance due to their wide use in numerous engineering applications. This work proposes a reliability estimation method for reciprocating seals based on multivariate dependence analysis of different performance indicators. Degradation behavior corresponding to each performance indicator is first described by the Wiener process. Dependence among different performance indicators is then captured using D-vine copula, and a weight-based copula selection method is utilized to determine the optimal bivariate copula for each dependence relationship. A two-stage Bayesian method is used to estimate the parameters in the proposed model. Finally, a reciprocating seal degradation …

Experimental Verification Of Transparent Spin Mode In Rhic, V. S. Morozov, P. Adams, Y. S. Derbenev, Y. Filatov, H. Huang, A. M. Kondratenko, M. A. Kondratenko, F. Lin, F. Méot, V. Ptitsyn, W. B. Schmidke, Y. Zhang

Engineering Technology Faculty Publications

High electron and ion polarizations are some of the key design requirements of a future Electron Ion Collider (EIC). The transparent spin mode, a concept inspired by the figure 8 ring design of JLEIC, is a novel technique for preservation and control of electron and ion spin polarizations in a collider or storage ring. It makes the ring lattice "invisible" to the spin and allows for polarization control by small quasi-static magnetic fields with practically no effect on the beam’s orbital characteristics. It offers unique opportunities for polarization maintenance and control in Jefferson Lab’s JLEIC and in BNL’s eRHIC. The …

Current-Driven Production Of Vortex-Antivortex Pairs In Planar Josephson Junction Arrays And Phase Cracks In Long-Range Order, Francisco Estellés-Duart, Miguel Ortuño, Andrés M. Somoza, Valerii M. Vinokur, Alex Gurevich

Physics Faculty Publications

Proliferation of topological defects like vortices and dislocations plays a key role in the physics of systems with long-range order, particularly, superconductivity and superfluidity in thin films, plasticity of solids, and melting of atomic monolayers. Topological defects are characterized by their topological charge reflecting fundamental symmetries and conservation laws of the system. Conservation of topological charge manifests itself in extreme stability of static topological defects because destruction of a single defect requires overcoming a huge energy barrier proportional to the system size. However, the stability of driven topological defects remains largely unexplored. Here we address this issue and investigate numerically …

Manufacturing Applications Of The One-Dimensional Cutting Stock Problem As A Team Project, Hüseyin Sarper, Nebojsa I. Jaksic

Electrical & Computer Engineering Faculty Publications

This paper explains the beneficial and practical impact of operations research in two real manufacturing settings. Two manufacturing examples used in student projects were (1) cutting rails (80‘ or 40‘) to manufacture railroad frogs of many sizes and (2) cutting round metal rolls (12‘ to 20‘) to meet customer demands for various lengths of cuts. Student teams in Engineering of Manufacturing Processes and Operations Research courses wrote computer programs. The program first identified all possible patterns that can be cut out of a given stock length. Next, the program created a mathematical model (a text file) as an output. This …

Evaluation Of Procurement Scenarios In One-Dimensional Cutting Stock Problem With A Random Demand Mix, Hüseyin Sarper, Nebojsa I. Jaksic

Electrical & Computer Engineering Faculty Publications

The one-dimensional cutting stock problem describes the problem of cutting standard length stock material into various specified sizes while minimizing the material wasted (the remnant or drop as manufacturing terms). This computationally complex optimization problem has many manufacturing applications. One-dimensional cutting stock problems arise in many domains such as metal, paper, textile, and wood. To solve it, the problem is formulated as an integer linear model first, and then solved using a common optimizer software. This paper revisits the stochastic version of the problem and proposes a priority-based goal programming approach. Monte Carlo simulation is used to simulate several likely …

Magnetron Sputtering Of Nb3Sn For Srf Cavities, Md. N. Sayeed, H. Elsayed-Ali, G. V. Eremeev, M. J. Kelley, U. Pudasaini, C. E. Reece

Electrical & Computer Engineering Faculty Publications

Nb₃Sn is a potential candidate for surface material of SRF cavities since it can enable the cavity to operate at higher temperatures with high quality factor and at an increased accelerating gradient. Nb-Sn films were deposited using magnetron sputtering of individual Nb and Sn targets onto Nb and sapphire substrates. The as-deposited films were annealed at 1200 °C for 3 hours. The films were characterized for their structure by X-ray Diffraction (XRD), morphology by Field Emission Scanning Electron Microscopy (FESEM), and composition by Energy Dispersive X-ray Spectroscopy (EDS) and Time of Flight Secondary Ion Mass Spectrometry (ToF-SIMS). The …

Preface To Special Topic: A Tribute To John Lumley, Kiran Bhaganagar, Thomas B. Gatski, William K. George

CCPO Publications

This Special Topic Section is dedicated to the life and memory of John Leask Lumley(1930-2015), professor and scientist extraordinaire.

Comment On "Roles Of Bulk Viscosity On Rayleigh-Taylor Instability: Non-Equilibrium Thermodynamics Due To Spatio-Temporal Pressure Fronts" Phys. Fluids 28, 094102 (2016), Robert L. Ash

Mechanical & Aerospace Engineering Faculty Publications

No abstract provided.

Impact Of Clip Connection And Insulation Thickness On Bracing Of Purlins In Standing Seam Roof Systems, Michael W. Seek, Daniel Mclaughlin

Engineering Technology Faculty Publications

The flexural strength of purlins in standing seam roof systems is highly dependent upon the extent to which the sheathing provides lateral and torsional restraint. Typical models to predict the restraint provided by the sheathing assume that the plane of lateral resistance occurs at the top flange of the purlin. In reality, depending on the configuration of the clip and the amount of insulation located between the purlin and the clip, the plane of lateral resistance and corresponding center of rotation shifts above the top flange. This distance, referred to as the effective standoff, is important to evaluate the effectiveness …

Evaluating The Readability Of Radio Frequency Identification For Construction Materials, Younghan Jung, Michael M. Jeong

Engineering Technology Faculty Publications

Radio Frequency Identification (RFID), which was originally introduced to improve material handling and speed production as part of supply chain management, has become a globally accepted technology that is now applied on many construction sites to facilitate real-time information visibility and traceability. This paper describes a senior undergraduate project for a Construction Management (CM) program that was specifically designed to give the students a greater insight into technical research in the CM area. The students were asked to determine whether it would be possible to utilize an RFID system capable of tracking tagged equipment, personnel and materials across an entire …

Error Aggregation In The Reengineering Process From 3d Scanning To Printing, Jennifer G. Michaeli, Matthew C. Degroff, Roman C. Roxas

Engineering Technology Faculty Publications

This work aims to study the aggregation of dimensional errors in the reengineering processes using 3D scanning and printing without initial design drawings. A 57-tooth spur gear is used as an example to facilitate the discussion. Two approaches are investigated. The first one builds the gear model based upon measurement taken from a caliper, and the second approach uses a 3D scanner to collect geometry data. Dimensional errors in each stage of these two approaches are investigated. Particular attention is paid to the geometry data flow in the reengineering process from data acquisition and editing to model construction. Recommendations are …