Engineering Commons^™

Analysis Of Multifrequency Dispersive Optical Bistability And Switching In Nonlinear Ring Cavities With Large Medium-Response Times, Pawel Pliszka, Partha P. Banerjee

Electrical and Computer Engineering Faculty Publications

Using a simple model of a ring cavity comprising a cubically nonlinear medium, we analyze dispersive optical bistability in the presence of more than one spectral component. We show the phenomenon of so-called competition for resonance. In addition to presenting cavity characteristics for the cases of two and three different frequencies, we also discuss the general method for finding steady-state solutions and checking their stability. A simple and efficient algorithm, based on a relaxation method, is devised to find steady-state solutions satisfying appropriate boundary conditions. The relaxation dynamics is physically related to a finite response time of the medium.

Mechanical Backup Systems For Electronic Environmental Controllers, Richard S. Gates, Douglas G. Overhults, Larry W. Turner

Biosystems and Agricultural Engineering Faculty Publications

A series of mechanical backup systems for electronic environmental controllers is presented for a typical finishing swine barn and a typical tunnel ventilated broiler house. The systems consist of mechanical thermostats and timers used in parallel with the electronic controller, designed to ensure animal survival in the event of controller or related hardware failure. For swine housing, three distinct mechanical backup functions are identified; for broiler housing, four distinct mechanical backup functions are identified. Schematic diagrams of the mechanical backup functions are provided and their implementation is described.

Theoretical And Experimental Study Of Inlet Manifold Pressure Profiles Using Compensated Transducers, P Mtui

Tanzania Journal of Engineering and Technology (TJET)

Computer simulation and experimental findings on single cylinder four-stroke cycle engine were done with a view of getting more realistic inlet manifold pressures. Since there is a direct relationship between the inlet pressure profiles and the volumetric efficiency of the engine, then there is a possibility of utilizing the knowledge of these profiles to enhance better engine air flow characteristics and hence improvement of engine performance.

The simulation program is based on hometropic process with constant specific heats where the results were validated using experimental findings of the engine with varying engine speeds.

Experimental results are obtained by measuring manifold …

Control System Design Program Based On Cascade Compensation, Fredrick Ishengoma

Tanzania Journal of Engineering and Technology (TJET)

CAD is becoming more widely accepted in the design and analysis of control systems. A program has been developed for analyzing single-input single-output linear time-invariant control system. The application of the progranl for frequency domain design of cascaded phase lead and phase lag coinpensators is briefly discussed. Two examples to illustrate the program are presented.

Development Of An Analog Mimo Quantitative Feedback Theory (Qft) Cad Package, Richard R. Sating

Theses and Dissertations

This thesis describes the development of an analog MIMO Quantitative Feedback Theory (QFT) CAD package for the automation of the multivariable control design process. The CAD package is capable of carrying a design from problem setup through the design process to a frequency domain analysis of the compensated MIMO system. The package automates the selection of the weighting matrix, formation of the square effective plants, the polynomial matrix inverse required to form the equivalent plants, generation of stability, tracking, disturbance, gamma, and composite bounds, loop shaping, design of the prefilter elements, and the frequency domain analysis of the completed design. …

Limaçon Of Pascal Locus Of The Complex Refractive Indices Of Interfaces With Maximally Flat Reflectance-Versus-Angle Curves For Incident Unpolarized Light, R. M.A. Azzam

Electrical Engineering Faculty Publications

For an interface between two isotropic media the power reflectance R_v (ø) is an even function, R_v (ø) = R_v (--), of the angle of incidence ø; hence all the odd derivatives, R_v⁽ⁿ⁾ = dⁿ R_v /døⁿ (n odd), are identically 0 at ø = 0, independent of the incident polarization v. When the incident light is unpolarized (v = u), the second derivative, R_u⁽²⁾, is also 0 at ø = 0, so that the flatness of the R_u -versus-ø curve …

Division-Of-Amplitude Photopolarimeter Based On Conical Diffraction From A Metallic Grating, R. M.A. Azzam

Electrical Engineering Faculty Publications

A new photopolarimeter that employs polarization-dependent conical diffraction of light by a metallic grating for the simultaneous measurement of the four Stokes parameters of light is described.

Performance Evaluation Of Spread Spectrum System With Cochannel Interference Through A Nonlinear Channel, Yong H. Kim

Dissertations

This thesis deals with the problem of more than one subscriber transmitting data signals through a common satellite repeater using code division multiplexing to separate the signals. We are concerned with the problem of amplifying two DS spread spectrum signals, both QPSK or BPSK modulated, in a common device in which limiting occurs. One signal is considered the signal we desire to receive, and the other, having the same nominal carrier frequency with a small random offset, is considered to be a cochannel interferer. The case of a cochannel interferer on the uplink and downlink in QPSK signalling and BPSK …

Process Technology And Characterization For Field Emission Devices, Jong Min Kim

Dissertations

Vacuum microelectronics is a new research field which applies semiconductor process technology to the fabrication of micron-dimensioned electron devices. Vacuum microelectronics is made possible by advances in microstructures and nanofabrication technology. Vacuum microelectronic devices are further characterized by a wide operating temperature range, nuclear radiation immunity, higher emission current density potential, and lower power consumption than that of thermionic emitters. The low mass of the electron provides a higher carrier mobility than GaAs or any solid state device. These features offer the potentials for wide variety of applications.

In this dissertation. electron field emission structures applicable to a variety of …

Investigation Of Epitaxial Lift-Off Gaas And Langmuir-Blodgett Films For Optoelectronic Device Applications, Divyang M. Shah

Dissertations

Epitaxial lift-off (ELO), a technique of removing an epitaxially grown GaAs layer from its growth substrate by selective etching of an AlAs sacrificial layer, is described for field-effect transistor fabrication independent of the GaAs growth substrate. Metal Semiconductor Field-Effect Transistors (MESFETs) and High Electron Mobility Transistors (HEMTs) fabricated on silicon and sapphire substrates using ELO are investigated. A 0.1 μm gate length depletion mode MESFET made on silicon exhibited a unity current gain frequency f_t = 34 GHz. Excellent device isolation with subpicoampere leakage currents is obtained. A high input impedance amplifier has been implemented on silicon substrate using …

Optimization Of A 3-Micron Bccd Process For High Density Ccd Registers, Mark Ratner

Theses

In July 1991, Dr. Walter F. Kosonocky proposed a High-Frame-Rate-CCD Imager. The design of the imager is such that the CCD channel width be 3-microns and capable of handling at least 3000 - 5000 electrons per square micron. Using process (SUPREM III) and device (PISCES IIB) simulations, charge handling capacities as a function of implant energy and junction depth were studied. Arsenic implants ranging from 100 to 200keV were driven-in to obtain junction depths between 0.40µm and 0.80µm. As a result of this work it was determined that charge handling capacities as high as 9400 electrons/µm² were achievable with …

Comparing Techniques Of Mapping Pyramid Algorithms Onto The Hypercube : A Case Study For The Connection Machine, Muhammad Ali Siddiqui

Theses

The pyramid structure is most widely used for low-level and intermediate-level image processing and computer vision because of its efficient support of both local and global operations. However, the cost of pyramid computers (PC) may be very high. They also do not support the efficient implementation of the majority of the scientific algorithms. In contrast, the hypercube network has widely been used in the field of parallel processing because it offers a high degree of fault tolerance, a small diameter and rich interconnection structure that permits fast communication at a reasonable cost. Thus, several algorithms have been developed for the …

A New Method To Optimize The Satellite Broadcasting Schedules Using The Mean Field Annealing Of A Neural Network, Youyi Yu

Theses

This thesis reports a new method for optimizing satellite broadcasting schedules based on the Hopfield neural model in combination with the mean field annealing theory. A clamping technique is used with an associative matrix, thus reducing the dimensions of the solution space. A formula for estimating the critical temperature for the mean field annealing procedure is derived, hence enabling the updating of the mean field theory equations to be more economical. Several factors on the numerical implementation of the mean field equations using a straightforward iteration method that may cause divergence are discussed; methods to avoid this kind of divergence …

An Embedded Controller-Based Fiber Optic Sensor For Use In Fresh Concrete, Zhaowu Zhang

Theses

The principle of refraction and reflection of light in optical fibers is applied to detection of air bubbles in a previous thesis. In the earlier work, a microcomputer was employed in acquisition and processing of air bubble data. In the present thesis, an embedded controller system is interfaced and programmed in order to replace the microcomputer. In this way, the system can be more easily integrated into field construction operations. Reflected light intensity signals are detected and analyzed by a microcontroller. The entrained percentage of air in concrete is displayed immediately. The signal can be transferred through a UART (Universal …

Analysis Of Electric Field On Surface Of An Atomically Sharp Field Emitter, Ziyan Cheng

Theses

In this thesis, exact calculation and computer simulation of an atomically sharp emitter are presented. In the theoretical analysis, the cathode-anode or cathode-gate complex is modeled for cone- and wedge-shaped emitters so that exact solution can be obtained. The exact solution reveals that the field on the emitter surface depends not only on the sharpness of the emitter, but also on the global geometry of the field emitter, gate, and anode complex. This finding is contrary to a widely accepted concept that field is predominantly determined only by local curvature of the tip.

The theoretical results are confirmed by computer …

Improvement Of Light Collection Efficiency By Laser-Induced Patterning The Surface Of Schottky-Barrier Solar Cells, Kejia Fang

Theses

In order to achieve maximum light collection efficiency in silicon made solar cells, reflectivity of the silicon surface must be reduced to as low level as possible. In the past, researchers have concentrated on coating the Si surfaces with anti-reflection coatings. Another approach was to form textures on the Si wafers to capture further the light impinging on the solar cells.

Theoretical studies, which were based on ray tracing approach, revealed that some geometrical patterns are better capturing the light than others. In this work, different geometrical surface configurations on a Cu/n-Si Schottky-barrier solar cell have been investigated. The configurations …

Processor Allocation Strategies For Modified Hypercubes, Nagasimha G. Haravu

Theses

Parallel processing has been widely accepted to be the future in high speed computing. Among the various parallel architectures proposed/implemented, the hypercube has shown a lot of promise because of its poweful properties, like regular topology, fault tolerance, low diameter, simple routing, and ability to efficiently emulate other architectures. The major drawback of the hypercube network is that it can not be expanded in practice because the number of communication ports for each processor grows as the logarithm of the total number of processors in the system. Therefore, once a hypercube supercomputer of a certain dimensionality has been built, any …

Modeling And Performance Of Token Bus Lan With Petri Nets, Zhenggang Pan

Theses

A token bus local area network (LAN) is analyzed by Generalized Stochastic Petri Nets (GSPN). The GSPN models of both a single station and LAN for four types of service schemes are obtained and their liveness property is proved. The network performance parameters comprise throughput and delay. The performance analysis for both symmetric and asymmetric single-service systems is conducted for varying load. In order to analyze a token bus LAN with a large number of stations, an approximation method is developed to resolve the .state space explosion problem. A token bus LAN with twenty-one stations is used to show the …

Applications Of Digital Signal Processing With Cardiac Pacemakers, Merry Thi Tran

Dissertations and Theses

Because the voltage amplitude of a heart beat is small compared to the amplitude of exponential noise, pacemakers have difficulty registering the responding heart beat immediately after a pacing pulse. This thesis investigates use of digital filters, an inverse filter and a lowpass filter, to eliminate the effects of exponential noise following a pace pulse. The goal was to create a filter which makes recognition of a haversine wave less dependent on natural subsidence of exponential noise.

Research included the design of heart system, pacemaker, pulse generation, and sensor system simulations. The simulation model includes the following components:

• Signal source, …

Comparison Of Synchronization Techniques For The Afit Direct Sequence Spread Spectrum System, Edward A. Bednar

Theses and Dissertations

The purpose of this study is to analyze and evaluate the performance of several code synchronization methods that could be used in the Air Force Institute of Technology's (AFIT) Direct-Sequence Spread Spectrum (DSSS) communication system. These methods include the sliding correlator, transmitted reference, sequential estimation, and three types of matched filters. The matched filters are the baseband matched filter, delay line matched filter, and the convolver. The criteria used for the evaluation of these synchronization methods are theoretical synchronization times and probability of bit-error. Advantages and disadvantages of each synchronization method are described and a method is recommended to be …

Fault Coverage Measurement Technique For Analog Circuits, E. Paul Ratazzi

Electrical Engineering and Computer Science - All Scholarship

This report describes an effort to develop a technique for measuring the amount of fault detection coverage that an analog test pattern has for a particular analog device. The technique is based on a software tool which statistically analyzes data from a circuit simulator. One example of a fault simulation experiment is presented, and some of the results are discussed. Finally, some ideas for future work in this area are given.

Transient Overvoltage Testing Of Environmental Controllers, Richard S. Gates, Larry W. Turner, Douglas G. Overhults

Biosystems and Agricultural Engineering Faculty Publications

The integrated electronic control system will provide a new method for the day-to-day management of environmental control of animal production systems. No standards are currently accepted for transient overvoltage protection of these controllers. To assess the adequacy of existing designs, a test circuit was designed and used for a transient open circuit over-voltage waveform (ANSI/IEEE C62.41-1980) of 16 environmental control units: a maximum spike of 770 V was applied to the power supplies, and a spike up to 100 V was applied to temperature sensor lines. For these relatively mild tests, no failures were noted due to power supply transients, …

Three-Dimensional Insulated Gate Bipolar Transistor (Igbt) Development, P.V. Gilbert, G.W. Neudeck

Department of Electrical and Computer Engineering Technical Reports

A new insulated gate bipolar transistor structure, the 3D-IGBT, is presented. The 3D-IGBT utilizes selective epitaxial silicon to form a top contacted anode and still retain the cellular structure of vemcally oriented devices. The 3D-IGBT , unlike other fully integrable power devices, exploits the merits of cellular structure to increase its packing density and thus reduce its on-resistance per unit area. It also eliminates the parasitic JFET resistance found in vertical IGBT's. To integrate the 3D-IGBT with low power devices, the QDI method of device isolation is also presented. QDI uses a combination of JI and DI to electrically isolate …

Achieving A Given Reflectance For Unpolarized Light By Controlling The Incidence Angle And The Thickness Of A Transparent Thin Film On An Absorbing Substrate: Application To Energy Equipartition In The Four-Detector Photopolarimeter, R. M.A. Azzam, Kurt A. Giardina

Electrical Engineering Faculty Publications

At a given wavelength λ we determine all possible solution pairs (ϕ, ζ) of the incidence angle ϕ and the thickness ζ of a transparent thin film on an absorbing substrate that achieve a given unpolarized light reflectance R_u. The trajectory of the point that represents a solution pair in the ζ, ϕ plane depends on the optical properties of the film and substrate and on whether R_u is greater than or less than the normal-incidence reflectance -R₀ of the bare substrate. When R_u > - R₀, the specified reflectance is achieved over a …

Series Compensation Investigation On The Hydro-Quebec And Nypa 765 Kv Transmission System : Modeling And Stability Analysis, Hans J. Candia

Theses

This thesis presents a mathematical approach for raising the power steady state stability limit by adding series capacitive compensation to a transmission line. The effect of series capacitive compensation and degree of compensation were investigated in detail. The power system studied includes an automatically controlled power system, IEEE Type I.

The results of the actual and theoretical steady state stability limits for a given series capacitance location and degree of compensation were obtained by applying the frequency domain technique. The natural frequencies of each compensated power network were examined.

The best location for series capacitive compensation is proposed which is …

Ion Exchanged Glass Waveguides With Efficient Coupling To Fibers And Lasers, Shiqing Hu

Theses

To be of practical use in optical communications networks, optical components must have both low on-chip losses and efficient coupling to fibers, semiconductor lasers and detectors. In this thesis work two types of channel waveguides were designed and fabricated on BK7 glass substrate using a low-cost ion-exchange process. The first type of waveguide was formed in a simple sequence of ion-exchange and post-exchange annealing. These single mode waveguides had large mode size and were efficiently coupled to single mode fibers. The lowest loss achieved in fiber-guide direct coupling was 1.25 dB. The second type of waveguide was formed in a …

Conditional Artificial Dielectric : Optically Controlled Microwave Modulator, J. Manuel Jimenez

Theses

A conditional artificial dielectric with embeddings of either CdS, GaAs or Si in PMMA form the dielectric material of a microstrip in a homodyne microwave detection system. The system consists of a Michelson or Mach-Zehnder interferometers with the microstrip placed in one arm. The index of refraction of the microstrip substrate is modulated by chopped incident light causing amplitude and phase variations in the incoming RF signal. Those variations are detected by mixing the light modulated microwave carrier(information channel) with the unmodulated carrier (reference channel) in the interferometer. The output is sensed by the square law detector and a lock-in …

Efficient Hypercube Communications, Shreyas R. Bhatt

Theses

Hypercube algorithms may be developed for a variety of communication-intensive tasks such as sending a message from one node to another, broadcasting a message from one node to all others, broadcasting a message from each node to all others, all-to-all personalized communication, one-to-all personalized communication, and exchanging messages between nodes via fixed permutations. All these communication patterns are special cases of many-to-many personalized communication. The problem of many-to-many personalized communication is investigated here.

Two routing algorithms for many-to-many personalized communication are presented here. The algorithms proposed yield very high performance with respect to the number of time steps and packet …

Translation Of 'Kamalakanta: A Collection Of Satirical Essays And Reflections', Monish Ranjan Chatterjee

Electrical and Computer Engineering Faculty Publications

This venture was born initially out of the desire to make those works of Bengali literature which have moved me profoundly, and which I consider first-rate by any yardstick, available to friends and fellow enthusiasts who cannot read the original. In attempting to channel literary and philosophical masterpieces into a different medium, I Have experienced firsthand the formidable challenge that a translator must face because not only of the barrier imposed by the languages involved, but perhaps more so because .of his or her own severely inadequate faculty being called upon to match both the genius and the inspiration of …

Studies Of High Field Conduction In Diamond For Electron Beam Controlled Switching, R. P. Joshi, M. K. Kennedy, K. H. Schoenbach, W. W. Hofer

Bioelectrics Publications

Experimental studies on a vertical metal‐diamond‐silicon switch structure have been conducted for potential pulsed power applications. Both the dc current‐voltage characteristics and the transient switching response have been measured for a range of voltages. With a 1 μm diamond film, the switch has been seen to withstand electric fields up to 1.8 MV/cm. Our results show a polarity dependence which can be associated with current injection at the asymmetric contacts. Polarity effects were also observed in the presence of e‐beam excitation, and arise due to nonuniform carrier generation near the diamond‐silicon interface. Our switching transients were seen to follow …