Engineering Commons^™

Petri Net Modeling And Performance Analysis Of Can Fieldbus, Ji-Qiong Zhou

Theses

The CAN FB (Controller Area Network FieldBus) has been in existence for ten years. It supports automated manufacturing and process control environments to interconnect intelligent devices such as valves, sensors, and actuators. CAN FieldBus has a high bit rate and the ability to detect errors. It is immune to noise and resistant to shock, vibration, and heat. Two recently introduced mechanisms, Distributed Priority Queue (DPQ) and Priority Promotion (PP) enable CAN FieldBus networks to share out the system bandwidth and grant ail upper bound on the transmission times so as to meet the requirements in real-time communications. Modeling and analysis …

Design, Fabrication And Characterization Of Silicon Microlenses For Ir-Ccd Image Sensors, Dhiren Pattnaik

Theses

There is a growing trend in the study of Focal Plane Arrays(FPAs) of very small microlenses, used for a wide variety of imaging and sensing applications, to increase optical efficiency. Present day sensor technology might take a different direction altogether with the development of compact, high quality, high resolution imaging microlenses, which could make the fill factor >90%. A method to increase light sensitivity of Interline Transfer(IT) type image sensors is to position microlens FPAs on top of the image sensors. FPAs are structures of small lenses which focus the incoming light on the photo sensitive part of the image …

Radiative Properties Of Silicon, Anamika Patel

Theses

The objective of this thesis was 1) to study the radiative properties of silicon in the wavelength range of 1 to 20 microns and temperature range of 30 to 1000°C for the development of a multi-wavelength pyrometer 2) to develop a [sic] methodologies for deconvolution of the measured optical properties to yield fundamental optical constants of bulk materials. A novel spectral emissometer has been utilized for measurement of the temperature dependent radiative properties of silicon. The temperature determination capability of the emissometer was tested and verified using a standard thermocouple embedded in a silicon wafer. The temperature measurement accuracy, with …

Collaborative Filtering In Tv Recommender, Elizabeth Podberezniak

Theses

The thesis describes different types of collaborative filtering methods to filter information from the large amount available and presents examples of such systems in different domains. It focuses on automated collaborative filtering to generate personalized recommendation of information.

Different variations of the automated collaborative filtering scheme are developed and analyzed in the thesis. An additional adjustment of the predicted score is implemented in order to improve precision of the recommendation. Different combinations of parameters are analyzed to maximize system effectiveness.

The data for the analysis was gathered through TV Recommender, a World Wide Web system developed for the thesis. The …

Modified Multiple Model Adaptive Estimation (M3Ae) For Simultaneous Parameter And State Estimation, Mikel M. Miller

Theses and Dissertations

In many estimation problems, it is desired to estimate system states and parameters simultaneously. However, inherent to traditional estimation architectures of the past, the designer has had to make a trade-off decision between designs intended for accurate state estimation versus designs concerned with accurate parameter estimation. This research develops one solution to this trade-off decision by proposing a new architecture based on Kalman filtering (KF) and Multiple Model Adaptive Estimation (MMAE) techniques. This new architecture, the Modified-MMAE (M³AE), exploits the benefits of an MMAE designed for accurate parameter estimation, and yet performs at least as well in state …

Microengineered Sensor Devices With Field Emission Electron Sources, Chao Sun

Dissertations

This dissertation describes the design, simulation, fabrication, and characterization of a microengineered pressure sensor device and a microengineered mass spectrometer device, both of which use field emission cathode tip arrays as electron sources. VLSI and MEMS process techniques are used to scale down the dimensions from existing vacuum pressure sensors and mass spectrometers.

The microengineered pressure sensor device is fabricated on a silicon substrate approximately 1cm by 1cm. It consists of an electron source in the form of cathode tip array structure, an electron accelerating space which includes a gas ionization volume, and an ion collection electrode. The electrons emitted …

Performance Analysis Of The Interference Adaptation Dynamic Channel Allocation Technique In Wireless Communication Networks, Ziqiang Xu

Dissertations

Dynamic channel allocation (DCA) problem is one of the major research topics in the wireless networking area. The purpose of this technique is to relieve the contradiction between the increasing traffic load in wireless networks and the limited bandwidth resource across the air interface. The challenge of this problem comes from the following facts: a) even the basic DCA problem is shown to be NP-complete (none polynomial complete); b) the size of the state space of the problem is very large; and c) any practical DCA algorithm should run in real-time.

Many heuristic DCA schemes have been proposed in the …

Orthogonal Transmultiplexers : Extensions To Digital Subscriber Line (Dsl) Communications, Xueming Lin

Dissertations

An orthogonal transmultiplexer which unifies multirate filter bank theory and communications theory is investigated in this dissertation. Various extensions of the orthogonal transmultiplexer techniques have been made for digital subscriber line communication applications.

It is shown that the theoretical performance bounds of single carrier modulation based transceivers and multicarrier modulation based transceivers are the same under the same operational conditions. Single carrier based transceiver systems such as Quadrature Amplitude Modulation (QAM) and Carrierless Amplitude and Phase (CAP) modulation scheme, multicarrier based transceiver systems such as Orthogonal Frequency Division Multiplexing (OFDM) or Discrete Multi Tone (DMT) and Discrete Subband (Wavelet) Multicarrier …

Enhanced Terahertz Pulse Generation And Detection Using Electric Field Singularities In Photo-Conducting Antennas, Yi Cai

Dissertations

In recent years, generation of ultra-short electromagnetic pulses with frequency components in the terahertz (THz) range has been achieved by various techniques. Among those different methods, photo-conducting antennas have proven to be the most efficient source of THz radiation. THz spectrometers utilizing such photo-conducting antennas as transmitters and receivers are meanwhile routinely used for spectroscopic studies in the frequency regime between 0.1 to 5THz, which can be covered by neither conventional optical nor microwave spectrometers. However, THz emission power from the existing photo-conducting antenna is not sufficient for many applications (such as electro-optic sampling for real time THz detection and …

Design And Characterization Of Ultra High Frame Rate Burst Image Sensors, Rakesh K. Kabra

Dissertations

This thesis research was aimed at investigating and designing novel architectures required for ultra high frame rate (UHFR) imagers capable of operating at frame rates in excess of 10⁶ frames/sec. To demonstrate the feasibility of these architectures, a 180 x 180 element UHFR-I imager was designed and fabricated. The imager chip stored the latest 32 frames at its on-chip memory locations rather than performing a continuous readout. It was demonstrated that this architecture approach could achieve a frame acquisition rate of 2 x 10⁶ frames/sec. Additionally, other novel design features were incorporated to minimize optical cross talk and …

Dual Material Gate Field Effect Transistor (Dmg-Fet), Wei Long

Dissertations

Improving performance and suppressing short channel effects are two of the most important issues in present field effect transistors development. Hence, high performance and long channel like behaviors are essential requirements for short channel FETs. This dissertation focuses on new ways to achieve these significant goals. A new field effect transistor - dual material gate FET (DMG-FET) - is presented for the first time. The unique feature of the DMG-FET is its gate which consists of two laterally contacting gate materials with different work functions. This novel gate structure takes advantage of material work function difference in such a way …

Decentralized Reliable Control For Large-Scale Lti Systems, Zhengfang Chen

Dissertations

Reliable control concerns the ability of closed loop system to maintain stability and regulation properties during arbitrary sensor, controller, and actuator failure. Reliable control research has been an active research topic for more than 10 years.

Recent approach for reliable control includes the H∞ method, the algebraic factorization design, and the robust servomechanism control. These methods have been surveyed and discussed in this thesis with the robust servomechanism control methodology serving as the basis of the research development of this work.

In this thesis, the reliable control for large-scale, multi-input/output linear system is considered. Two concepts of reliable control …

Cantilever Beam Microactuators With Electrothermal And Electrostatic Drive, Murat M. Okyar

Dissertations

Microfabrication provides a powerful tool for batch processing and miniaturization of mechanical systems into dimensional domain not accessible easily by conventional machining. CMOS IC process compatible design is definitely a big plus because of tremendous know-how in IC technologies, commercially available standard IC processes for a reasonable price, and future integration of microma-chined mechanical systems and integrated circuits. Magnetically, electrostatically and thermally driven microactuators have been reported previously. These actuators have applications in many fields from optics to robotics and biomedical engineering.

At NJIT cleanroom, mono or multimorph microactuators have been fabricated using CMOS compatible process. In design and fabrication …

Micro Electromechanical Relays And Their Application In Variable Inductor Networks, Shifang Zhou

Dissertations

A family of microrelay devices together with integrated inductor networks has been designed, simulated, fabricated and experimental characterized. These switched networks utilize microelectromechanical systems (MEMS) as a fabrication technology and take advantage of the economies of semiconductor cleanroom batch-processing.

A new type of microrelay has been developed using a suspended TaSi₂/SiO₂ bimorph cantilever beam, gold-to-gold electrical contact, aluminum as sacrificial layer, and a combined thermal and electrostatic means of actuation. For the first time a micro variable inductor network which is digitally controlled by microrelays has been demonstrated. A test structure for electrical micro contact characterization has …

Performance Enhancement Of Linear Robotic Workcell Using Dsp Based Control, Kedar Arvind Godbole

Theses

Robotic Controllers have for the major part been computer implementations of PID or similar controllers. In this thesis DSP based control of a Robotic Workcell is presented. The control algorithms used with the DSP based controller are Input Shaping and also State Feedback. Input Shaping is a Feed Forward strategy for eliminating vibration under certain conditions. In this thesis Input Shaping is applied to the performance enhancement of a linear robot system. Although feedback control strategies offer higher accuracy and are much more robust, feedforward strategies offer possibilities for improving the response time. Input Shaping is successfully applied to the …

Investigation Of Optical Properties Of Inp, Ain And Sapphire For Applications In Non-Contact Semiconductor Process Monitoring, Rajasekhar Velagapudi

Theses

The objective of this thesis was to develop a reliable multi-wavelength pyrometer for simultaneous measurement of the wafer temperature and its optical properties in the wavelength range of 1 to 20 microns and temperature range of 30 to 1500° C. The spectral emissometer has been utilized for measurement of the temperature dependent optical properties of InP, AlN and Sapphire. The experimental results presented in this thesis showed that the measurement of high temperature optical properties could be performed reliably with a novel approach using the spectral ernissometer. The temperature determination capability of the emissometer was tested and verified using a …

A Design-For Retirement Rating Model For Environmentally Conscious Products, Xin He

Theses

Design-For-Retirement is a concept that allows one to design a product such that its retirement time and post-life treatment are optimized to lead to the minimum environmental impact and maximum financial gain. Retired product parts or subassemblies face three primary multi-lifecycle engineering treatments. The first one is to recondition them for reuse in the next lifecycle. The second one is to convert their post life parts into a material form for recycling back into new parts. The last is to dump or landfill them. Each option has a significantly different environmental cost-benefit ratio. Another important concern is the dismantling process …

Fuel Cells, Frederick J. Munster Jr.

Maine Collection

Fuel Cells

by Frederick J. Munster Jr.

Edited by: Mr. Christopher Carroll

Maine Department of Economic Development, Augusta, Maine, 1998.

Contents: Hydrogen / Hydrogen Safety / Electrolysis / Electrolyzers / History of Fuel Cells / How Fuel Cells Operate / Fuel Cell Types / Fuel Cell Electrochemistry / Power Systems / Fuel Cells in Transportation / Hydrogen Powered Internal Combustion Engines / Home, Garden, Education and Industry / For More Information / Glossary / References

Emission Of Excimer Radiation From Direct Current, High-Pressure Hollow Cathode Discharge, Ahmed El-Habachi, Karl H. Schoenbach

Bioelectrics Publications

A novel, nonequilibrium, high-pressure, direct current discharge, the microhollow cathode discharge, has been found to be an intense source of xenon and argon excimer radiation peaking at wavelengths of 170 and 130 nm, respectively. In argon discharges with a 100 μm diam hollow cathode, the intensity of the excimer radiation increased by a factor of 5 over the pressure range from 100 to 800 mbar. In xenon discharges, the intensity at 170 nm increased by two orders of magnitude when the pressure was raised from 250 mbar to 1 bar. Sustaining voltages were 200 V for argon and 400 V …

Attitude Measurement, Mark A. Stedham, Partha P. Banerjee, Seiji Nishifuji, Shogo Tanaka

Electrical and Computer Engineering Faculty Publications

In many practical situations, it is important to determine and measure the attitude of a particular vehicle, such as a ship, an airplane, a piece of mechanical equipment such as a, crane lifter, or a spacecraft. For this reason, many attitude sensors have been developed with advanced computer and semiconductor technologies. This section first introduces the various attitude sensors with an explanation of their operating principles and then presents several methodologies for attitude measurement and determination, including ships and crane lifters, aircraft, and spacecraft applications.

Signal Processing Topics In Multicarrier Modulation : Frequency Offset Correction For Ofdm And Multiuser Interference Cancellation For Mc-Cdma, Pingping Zong

Theses

Orthogonal frequency division multiplexing (OFDM) is discussed as a special form of multi-carrier modulation (MCM). One major problem of the OFDM system is the sensitivity to an unknown frequency offset at the receiver. To improve the performance of the OFDM system, correction of the frequency offset is required before decision making. An adaptive method of frequency offset correction is presented. The adaptation algorithm used here is based on the LMS and the estimation is proven unbiased. A multiuser communications system having similar signal structure to the OFDM system, termed as multi-carrier code division multiple access (MC-CDMA), is discussed. The MC-CDMA …

Joint Map Registration And High Resolution Image Estimation Using A Sequence Of Undersampled Images, Russell C. Hardie, Kenneth J. Barnard, Ernest E. Armstrong

Electrical and Computer Engineering Faculty Publications

n many imaging systems, the detector array is not sufficiently dense to adequately sample the scene with the desired field of view. This is particularly true for many infrared focal plane arrays. Thus, the resulting images may be severely aliased. This paper examines a technique for estimating a high-resolution image, with reduced aliasing, from a sequence of undersampled frames. Several approaches to this problem have been investigated previously. However, in this paper a maximum a posteriori (MAP) framework for jointly estimating image registration parameters and the high-resolution image is presented. Several previous approaches have relied on knowing the registration parameters …

Microelectromechanical Scanner Using A Vertical Cavity Surface Emitting Laser, Joseph G. Bouchard Jr.

Theses and Dissertations

Optical scanners play a prominent role in the commercial and military industries. The scanner's size, cost and reliability are critical characteristics. In this research a microoptical scanning system was fabricated by incorporating a vertical cavity surface emitting laser (VCSEL) onto a surface machined microelectromechanical die. The micro optics for laser beam steering includes a 135 deg mirror, a Fresnel lens, a lateral scanning rotating mirror, and a vertical scanning fan mirror. The VCSEL was attached to the die by solder and electrical connection was provided by wire bonding. Based on far field measurements the scanner had a lateral scan angle …

Multiple Model Adaptive Estimation And Control Redistribution Performance On The Vista F-16 During Partial Actuator Impairments, Curtis S. Clark

Theses and Dissertations

Multiple Model Adaptive Estimation with Control Reconfiguration (MMAE/CR) capability to estimate and compensate for partial actuator failures, or "impairments" is investigated using the high-fidelity, nonlinear, six-degree-of-freedom, VISTA F-16 simulation which currently resides on the Simulation Rapid-Prototyping Facility (SRF). After developing a model for inserting partial actuator impairments into the VISTA F-16 truth model, research begins with a battery of single actuator impairment tests. This stage of research explores the capability of the existing MMAE algorithm to estimate single, partial actuator impairments, and helps to define refinements and expansions needed in the MMAE algorithm for the second phase of research: the …

Secondary Data Support And Non-Homogeneities In Space-Time Adaptive Processing, Todd B. Hale

Theses and Dissertations

One of the primary problems with the application of Space-Time Adaptive Processing (STAP) techniques is secondary data support for the interference plus noise covariance matrix estimate. Reed has shown the required secondary data support to achieve performance within 3 dB of optimal SINR is approximately equal to twice the degrees of freedom (DOF) used in the algorithm. Reed proved this rule for Sample Matrix Inversion (SMI) techniques. A concern arises when applying this rule to a newer class of reduced dimension STAP algorithms that do not fall under the SMI umbrella. This thesis focuses on the Cross Spectral Metric (CSM) …

Optimized Design Methodology Of Cavity-Backed Microstrip Antennas With Dielectric Overlays, Douglas J. Hermes

Theses and Dissertations

The optimized design methodology implemented in this research employs a design methodology, namely Response Surface Methodology (RSM), that is relatively new to the electromagnetics field. The design methodology used a full factorial designed experiment, a Hybrid Finite Element Method (HFEM) analysis code, a cubic spline empirical model, an Analysis of Variance (ANOVA) test, and a simplex optimization code to successfully measure, predict, analyze, and optimize average antenna gain and antenna input impedance for a cavity backed microstrip antenna with dielectric overlays. Based on HFEM results from the full factorial designed experiment, a cubic spline empirical model successfully predicted average antenna …

A Single Chip Low Power Implementation Of An Asynchronous Fft Algorithm For Space Applications, Bruce W. Hunt

Theses and Dissertations

A fully asynchronous fixed point FFT processor is introduced for low power space applications. The architecture is based on an algorithm developed by Suter and Stevens specifically for a low power implementation. The novelty of this architecture lies in its high localization of components and pipelining with no need to share a global memory. High throughput is attained using large numbers of small, local components working in parallel. A derivation of the algorithm from the discrete Fourier transform is presented followed by a discussion of circuit design parameters specifically, those relevant to space applications. The generic architecture is explained with …

Micro-Electromechanical Switches For Micro-Satellite Power Transfer, Glen A. Kading

Theses and Dissertations

In the past few years, microelectromechanical systems (MEMS) have emerged as a promising new technology with tremendous application potential. One of the possible implementations of MEMS technology is in the development of micro-satellites. It should be possible to mass-produce micro-satellites at a fraction of the cost of one conventional satellite. In order for satellites to be robust, a method of transferring power to systems must be addressed. As micro-satellites are made with conventional integrated circuit technologies at a very small scale, a means of transferring power on a similar scale will be investigated. This research addresses the issue of the …

A Wire Antenna Designed For Space Wave Radiation Over The Earth Using A Genetic Algorithm, Brian S. Sandlin

Theses and Dissertations

A wire antenna is designed for optimal performance at low elevation angles in the presence of a lossy half-space. A simple genetic algorithm (GA) and GENOCOP III software are each integrated with Numerical Electromagnetics Code Version 4.1 (NEC4.1) to optimize a wire antenna geometry for multiple objectives: power gain, azimuthal symmetry, and input impedance. The performance of the two versions of the integrated GA are compared. Several of the resulting antennas are analyzed, and an antenna is proposed for use in a Remote Intrusion Monitoring System (RIMS). Simulations suggest that the proposed antenna, which is well-matched, offers a significant increase …

Evaluation Of A Maximum A-Posteriori Slope Estimator For A Hartmann Wavefront Sensor, Troy B. Van Caster

Theses and Dissertations

Current methods for estimating the wavefront slope at the aperture of a telescope using a Hartmann wavefront sensor are based upon a centroid shift estimator. The centroid shift estimator determines the displacement, or shift, of the centroid off the optical axis using a moment calculation of the intensity distributions recorded in each subaperture. This centroid shift is proportional to the average slope of the wavefront in each subaperture. A maximum a-posteriori (MAP) slope estimator takes advantage of a-priori knowledge of the wavefront slope statistics and total irradiance falling on the subaperture detector arrays when determining the shift estimate. In order …