Engineering Commons^™

Preparation And Photo-Catalyst Properties Of The α-Fe2O3-Tio2 Films On Sodium Alginate Polymer, Li-Qin Chen, Huai-Zhen Zhong, Ri-Yao Chen, Xi Zheng, Zhen Chen

Journal of Electrochemistry

Three new nano thin films of α-Fe₂O_3, TiO₂ and α-Fe₂O₃-TiO₂ by doping their powder with sodium alginate polymer were prepared. Surface structure and catalytic activities of the films were characterized by FTIR, XRD, PL, TEM and I-V techniques. The results of UV-visible absorption showed that the methylene blue was mineralized in aqueous of α-Fe₂O₃/SA, TiO₂/SA and (α-(Fe₂O₃))-TiO₂ /SA upon radiation with ultra violet light. α-Fe₂O₃ enhanced their photo-decolorized-activities by doping 15% TiO₂.

Interfacial Stability Of Electrodeposition Of Cuprous Oxide Thin Films, Partho Neogi

Chemical and Biochemical Engineering Faculty Research & Creative Works

Experiments on deposition of Cu₂O films from basic cupper sulfate solution show that copper also deposits. At low, but basic values of pH only copper deposits and at high pH only cuprous oxide deposits. In the intermediate range where both compete the system shows oscillations at "constant current." Linear stability analysis has been conducted for such an electrochemical cell to show that oscillations can take place in the parameter space identified in the experiments. The results are keeping with most of the experimental observations, which are many, but not with all. The physical mechanisms behind the oscillations are …

Stable Zeolite/Cellulose Composite Materials And Method Of Preparation, Gustavo F. Larsen

Department of Chemical and Biomolecular Engineering: Patents

Stable cellulosic fiber material for use in forming zeolite/cellulose composites is prepared by suspending loose cellulose fibers in an aqueous solution of sodium hydroxide, potassium hydroxide or sodium silicate, stirring the resulting suspension until it reaches a macroscopically homogenous appearance, heating the resulting mixture at a temperature of 323-423 K until only dry solids remain, contacting the resulting mixture with excess distilled water to remove physically adsorbed or trapped sodium hydroxide, potassium hydroxide or sodium silicate from the fibers, and heating the resulting fiber material at 323-423 K to dry the fiber material. Stable zeolite/cellulose composite material characterized in that …

Monoliths As Multiphase Reactors: A Review, Shaibal Roy, Tobias Bauer, Muthanna H. Al-Dahhan, Peter Lehner, Thomas Turek

Chemical and Biochemical Engineering Faculty Research & Creative Works

Monolith Reactors Are Being Studied as a Replacement for Conventional Multiphase Reactors Such as Trickle-Bed Reactors, Slurry Reactors, and Slurry Bubble Column Reactors for Gas-Liquid-Solid Reactions. Reactors with Monolith Catalyst Packing Have Been Found to Be Hydrodynamically Superior to Existing Industrial Reactors. This Review Covers Multiphase Reactions Carried Out in Monolith Reactors by Various Researchers. It First Defines the Monolith Reactor and Looks into the Geometrical Aspects of Monolith. the Section Dealing with Hydrodynamics Reviews Pressure Drop, Phase Holdup, Flow Distribution, and Dispersion Characteristics. This Study Also Considers the Tools Used to Characterize the Hydrodynamic Parameters and their Typical Values. …

Quantification Of Solids Flow In A Gas-Solid Riser: Single Radioactive Particle Tracking, Satish Bhusarapu, Muthanna H. Al-Dahhan, Milorad P. Dudukovic

Chemical and Biochemical Engineering Faculty Research & Creative Works

Solids in Risers of Circulating Fluidized Beds (CFB) Exhibit Local Backflow and Recirculation. Measurement of the Concentration-Time Response to an Impulse Injection of Tracer, Even at Two Elevations Cannot Determine the Residence Time Distribution (RTD) of Solids Uniquely. Hence, Evaluation of RTD in Risers from Conventional Tracer Responses is Difficult and Often Not Possible. in Addition, Estimating the Solids Circulation Rate in These Closed Loop Systems, is a Non-Trivial Problem. in This Work, a Single Radioactive Particle in the CFB Loop is Tracked during its Multiple Visits to the Riser And, by Invoking Ergodicity, Solids Circulation Rate, Accurate Solids RTD …

Liquid Holdup And Pressure Drop In The Gas-Liquid Cocurrent Downflow Packed-Bed Reactor Under Elevated Pressures, Jing Guo, Muthanna H. Al-Dahhan

Chemical and Biochemical Engineering Faculty Research & Creative Works

An Experimental Investigation of the Residence Time Distribution, Liquid Holdup, and Pressure Drop in a Gas-Liquid Downflow Packed Bed Reactor with Porous Particles Operated under Elevated Pressures is Presented. the Effects of the Two-Phase Flow Rates and Reactor Pressures on the External Liquid Holdup and Pressure Drop Are Discussed. a Mechanistic Model, Which Accounts for the Interaction between the Gas and Liquid Phases by Incorporating the Shear and Velocity Slip Factors between Phases, is Employed to Predict the External Liquid Holdup and Pressure Drop for the Experimentally Covered Flow Regime. the Involved Parameters, Such as Shear and Velocity Slip Factors …

Optimization Of Batch Reactions In Series With Uncertainty, Keith G. Tomazi

Chemical and Biochemical Engineering Faculty Research & Creative Works

Certain types of chemical reactions, such as the global deprotection of a polypeptide, are extremely complex. As a result, it may be very difficult or expensive to develop accurate models of these chemical reactions. Without a satisfactory kinetic model for the reaction, it is difficult to develop an optimum operating policy that will maximize the profit. Stochastic optimization is applied in this work to an example process step to obtain the optimum reaction temperature and reaction time. In the case of the "here and now" problem, the optimal conditions are a lower reaction temperature and a longer reaction time than …

Exergy Use In Bioenergetics, Yaşar Demirel

Papers in Analytical Chemistry

Every developed and adapted biological system extracts useful energy from outside, converts, stores it, and uses for muscular contraction, substrate transport, protein synthesis, and other energy utilizing processes. This energy management in a living cell is called the bioenergetics, and the useful energy is the exergy, which is destroyed in every irreversible process because of the entropy production. The converted exergy is the adenosine triphosphate (ATP) produced through the oxidative phosphorylation coupled to respiration in which the exergy originates from oxidation of reducing equivalents of nutrients. A living cell uses the ATP for all the energy demanding activities; it has …

Fall 2004 Che Newsletter, Department Of Chemical Engineering, Michigan Technological University

Department of Chemical Engineering Newsletters

Table of Contents

• Letter from the Chair
• Michigan Tech nano research gets $1 million boost from House
• New Inductees for Chemical Engineering Distinguished Academy Honored
• Undergraduate Expo 2004- AFG takes 3rd Place in Poster Presentation
• Chem-E car Takes Second Plate in the Nationals
• Western UP Science Fair
• Sandell Joins department
• Kimojino Awarded Fellowship

Production And Purification Of A Chimeric Monoclonal Antibody Against Botulinum Neurotoxin Serotype A , Mark C. Mowry, Michael Meagher Lead Investigator, Leonard Smith, Anuradha Subramanian

Papers in Biotechnology

Production of recombinant antibodies against botulinum neurotoxin is necessary for the development of a post-exposure treatment. CHO-DG44 cells were transfected with a plasmid encoding the light and heavy chains of a chimeric monoclonal antibody (S25) against botulism neurotoxin serotype A. Stable cell lines were obtained by dilution cloning and clones were shown to produce nearly equivalent levels of light and heavy chain antibody by an enzyme-linked immunosorbent assay (ELISA). In suspension culture, cells produced 35 μg/ml of chimeric antibody after 6 days, corresponding to a specific antibody productivity of 3.1 pg/cell/day. A method for the harvest and recovery of an …

Layer-By-Layer Nanoassembly Combined With Microfabrication Techniques For Microelectronics And Microelectromechanical Systems, Jingshi Shi

Doctoral Dissertations

The objective of this work is to investigate the combination of layer-by-layer self-assembly with microfabrication technology and its applications in microelectronics and MEMS.

One can assemble, on a standard silicon wafer, needed multilayers containing different nanoparticles and polymers and then apply various micromanufacturing techniques to form microdevices with nanostructured elements.

Alternate layer-by-layer self-assembly of linear polyions and colloidal silica at elevated temperatures have been firstly studied by QCM and SEM. LbL self-assembly and photolithography were combined to fabricate an indium resistor. The RTA method was employed in the fabrication. Hot-embossing technique as a reasonably fast and moderately expensive technique was …

Haemophilic Factors Produced By Transgenic Livestock: Abundance That Can Enable Alternative Therapies Worldwide, Kevin E. Van Cott, Paul E. Monahan, Timothy C. Nichols, William H. Velander

Papers in Biotechnology

Haemophilia replacement factors, both plasma-derived and recombinant, are in relatively short supply and are high-cost products. This has stymied the study and development of alternative methods of administration of haemophilia therapy even in the most economically advanced countries, owing to the large amounts of material needed because bioabsorption and bioavailability of haemophilic factors can be less than 10% when using non-intravenous routes of delivery. There is therefore a need to increase access to therapy worldwide by decreasing the cost and increasing the abundance so that therapy can be achieved through simplified, alternative delivery methods. Transgenic livestock have been used to …

Biomimetic Synthesis Within Polyelectrolyte Microcapsules: Characterization Of Enzyme Catalyzed Polyphenols And Polypeptides, Rohit C. Ghan

Doctoral Dissertations

An enzyme-catalyzed synthesis of novel polymers within layer-by-layer (LbL) constructed polyelectrolyte microcapsules has been developed. This approach is based on the selective permeability of polyelectrolyte-capsule walls to monomer molecules. Conversely biocatalysts and forming polymeric chains cannot exit the micro-capsule interior because of their characteristic high molecular weight. Horseradish Peroxidase (HRP) was encapsulated into four bilayer PSS (poly-styrenesulfonate)/PAH (poly-allylamine hydrochloride) capsules with an average diameter of 5 μm using pH-driven pore opening. The polymerization of 4-(2-Aminoethyl) phenol hydrochloride (tyramine) catalyzed by HRP produces easily detectable fluorescent polymeric products after the addition of hydrogen peroxide to the system. It is known that …

Statistical Mechanics Of Worm-Like Polymers From A New Generating Function, Gustavo A. Carri, Marcelo Marucho

College of Polymer Science and Polymer Engineering

We present a mathematical approach to the worm-like chain model of semiflexible polymers. Our method is built on a novel generating function from which all the properties of the model can be derived. Moreover, this approach satisfies the local inextensibility constraint exactly. In this paper, we focus on the lowest order contribution to the generating function and derive explicit analytical expressions for the characteristic function, polymer propagator, single chain structure factor, and mean square end-to-end distance. These analytical expressions are valid for polymers with any degree of stiffness and contour length. We find that our calculations are able to capture …

Chemical/Mechanical Analyses Of Anhydride-Cured Thermosetting Epoxys: Dgeba/Nma/Bdma, Wei Chian, Delmar C. Timm

Papers in Molecular Chemistry

The chemical state of cure in a thermosetting resin was used to predict the resin’s equilibrium modulus. High performance liquid chromatography analyses of the sol fraction yielded molar dynamics for monomeric, oligomeric, and polymeric molecules. Their population density distributions were compared with theoretical predictions based on a chain-growth polymerization mechanism. The resulting chemical estimates of the state of cure were integrated into calculations yielding concentrations of network structures within the gel that contribute to the density of elastically active strands and junctions. The theory of rubber elasticity was then used to predict the equilibrium modulus. Measurements incorporated dynamic mechanical analysis. …

Kinetic Reaction Analysis Of An Anhydride-Cured Thermoplastic Ep-Oxy:Pge/Nma/Bdma, Wei Chian, Delmar C. Timm

Papers in Molecular Chemistry

A comprehensive reaction analysis of a linear epoxy resin cured with an anhydride was performed to evaluate the reaction rate expressions. Monomers included phenyl glycidyl ether and methyl- 5-norbornene-2,3-dicarboxylic anhydride or nadic methyl anhydride; the catalyst was N,N-dimethylbenzylamine; the initiator was n-propanol. Emphasis was initially placed on the molar dynamics of monomeric and oligomeric molecules. Molecular fractionations were achieved using reversed phase, high performance liquid chromatography. Chemical reaction rate constants were examined as a function of degree of polym-erization. For the chain-initiated polymerization, the initiation rate constant was observed to be approximately 3 times greater than the propagation constant associated …

Determining Suitability Of A Fly Ash For Silica Extraction And Zeolite Synthesis, Natàlia Moreno, Xavier Querol, Angel López-Soler, José Manuel Andres, Maria Janssen, Henk Nugteren, Mark R. Towler, Kenneth Stanton

Chemical and Biochemical Engineering Faculty Research & Creative Works

Zeolitic material is obtained from fly ash both by direct conversion of the ash or from SiO₂ extracts obtained from fly ash. This study focuses on determining the suitability of a fly ash for SiO₂ extraction and for zeolite synthesis by direct conversion. The SiO₂ extraction experiments from different fly ashes show that the main parameters governing the SiO₂ extraction are: (a) a high bulk SiO₂ content (> 52%, for obtaining an extraction yield of 100 g SiO₂ kg-1) in the starting fly ash, (b) a high proportion (> 55%) of the bulk SiO …

Fluidization Of Nanoparticles, Caroline Hijung Nam

Dissertations

During the past decade, nanoparticles (1-100 nm) and nanocomposites have become the focus of many studies due to the unique properties of nanostructured materials that make them attractive for various applications. Due to their atomic and molecular interactions, nanoparticles and nanocomposites have unique and often favorable catalytic, mechanical, optical, electronic and / or other properties. For instance, nanocrystalline copper is up to 5 times harder than conventional micron sized copper particles. Nanocomposites, such as a homogenous mixture of different nanoparticles, can also exhibit improved properties. Other examples include coating and reacting nanoparticles with a second nanostructured phase. These processes are …

Fluidization Of Agglomerates Of Nanoparticles Under Different Force Fields, Jose A. Quevedo

Theses

Nanoparticles are the focus of many research activities, and in the near future they will be handled in large amounts by industry. Fluidization is a very important unit operation which is applied in several industrial processes.

In the present work, fluidization experiments with agglomerates of nanoparticles were done under different force fields: (1) gravity force or conventional fluidization; (2) a magnetic force field, which uses magnetic particles under the influence of a magnetic field; and (3) a centrifugal force, generated by a rotating frame that simulates higher gravity conditions.

Among the significant results with agglomerates of nanoparticles, conventional fluidization was …

Electrochemical Reduction Of Nitrobenzene On The Wc Electrode In Acidic Solution, Chun-An Ma, You-Qun Chu, Ying-Hong Zhu, Zhi-Hua Xu

Journal of Electrochemistry

The tungsten carbide (WC) electrode was constructed by using polyterafluoroethylene as binder. The electrochemical behavior of nitrobenzene on the WC electrode in acidic solution was investigated by cyclic voltammetry, linear scan method and chronoamperometry. Experimental results showed that WC electrode had good activity for the electrochemical reduction of nitrobenzene, and the electrode process was controlled by diffusion and electrochemical stepssimultaneously. The apparent active energy of the electrode process is 23.7kJ⋅mol^-1, while the active energy of the electrochemicalstep is 10.91kJ⋅mol^-1.

Synthesis Of (S)-3-Phenylpropane-2-Tert-Butoxycarbonylamino-1-Thiol And Its Electrochemical Behavior Self-Assembled On Gold, Ru Sun, Jian-Feng Ge, Mei Wang, Ren-Ao Gu

Journal of Electrochemistry

The synthesis of (S)-3-Phenylpropane-2-tert-butoxycarbonylamino-1-thiol(N-Boc-APT) from L-phenylalanine was reported. L-Phenylalanine was reduced to the corresponding amino alcohol, protection of the amino group using tert-butyl pyrocarbonate gave (S)-2-tert-butoxycarbonylamino-3-phenylpropane-1-ol, which was then O-mesylated and treated with potassium thioacetate in DMF to give 3-phenylpropane-2-tert- butoxycarbonylamino-1-etylmercapto. After the acetyl group was removed with ammonia in alcohol, the desired target molecular was obtained. The structure of intermediate and target molecular was conformed by IR and ¹HNMR. We made N-Boc-APT self-assemble-modificated gold electrode and investigated its electrochemical behavior. The CV results of methylene blue on nano-Au/N-Boc-APT SAM/Au electrode showed that nano-Au could speed this electron transfer …

Solid State Synthesis And Electrocatalysis Of Pt/Moo3 For The Oxidation Of Methanol, Qing Wang, Yi-Ming Zhou, Yang Shao, Yi-Gang Ji, Juan Xu, Ya-Wen Tang, Tian-Hong Lu, Tao Shen

Journal of Electrochemistry

The electrocatalyst, Pt/MoO₃ synthesized by solid state reaction, was used for the oxidation of methanol in direct methanol fuel cells. The X-Ray diffraction and cyclic voltammetry were employed to investigate the performance of the material. It was shown that the typical diffraction peaks for Pt appeared in XRD. And a good electrocatalysis for methanol oxidation was observed. The peak potential of the methanol oxidation appeared at ca. 0.63V(vs.SCE) and the peak current density for the oxidation was 78.1 mA⋅cm^-2.

Synthesis And Electrochemical Behavior Of Layered-Structure Limn1-XCrXO2, Jie Xiao, Hui Zhan, Yun-Hong Zhou

Journal of Electrochemistry

The Layered-structure LiMn_1-xCr_xO₂(x=0, 0.15) solid solution has been prepared by the rheological phase method. From the XRD results, undoped LiMnO₂ crystallized almost entirely in the orthorhombic phase while the structure of LiMn_0.85Cr_0.15O₂ belongs to monoclinic phase. TEM investigation shows that the final powder product consists of ultrafine spherical particles which are distributed homogeneously, with the average diameter ranging from 60 to 300nm. The initial discharge capacity of LiMn_0.85Cr_0.15O is much higher than that of undoped LiMnO₂. After 40 cycles, the capacity retention …

Lithium Insertion Into Tio2(B) Nanobelts Synthesized By The "Soft Chemical" Method, Cha-Geng Nie, Zheng-Liang Gong, Lan Sun, Juan Zuo, Yue-Kun Lai, Chang-Jian Lin

Journal of Electrochemistry

TiO₂(B) Nanobelts were synthesized by using the "Soft chemical"method. The products were characterized by means of transmission electron microscope(TEM), X-ray diffraction(XRD), Raman spectrum and energy dispersive spectrum(EDS). Galvanostatic charging and discharging tests showed that lithium-ion intercalation/deintercalation occurred reversibly in the TiO₂(B) nanobelts electrode, and a high capacity (265 mAh·g^-1) can be obtained. The results suggested that TiO₂(B) Nanobelts might be a promising negative electrode material of second Lithium battery.

Preliminary Study Of Speek Membranes For Direct Methanol Fuel Cells Application, Su-Zhen Ren, Zhen-Xing Liang, Xin-Sheng Zhao, Qin Xing, Gong-Quan Sun, Xue-Feng Yang

Journal of Electrochemistry

This paper describes the methanol permeability characterization of SPEEK membranes and their feasibility for DMFC application. The SPEEK membranes showed a significant lower methanol permeation than Nafion 115 determined from voltammetric methods. An increase in open circuit voltage was found in the performance of SPEEK membranes in DMFC. The power density of the cell using SPEEK membrane was considerably poorer than that of Nafion 115. If modified properly, the SPEEK membranes can be chosen for DMFC application based on this study.

Fabrication Of Solid Oxide Fuel Cells And Analysis Of Their Structure And Performance, Nai-Tao Yang, Bo Meng, Ru-Jun Yu, Xiao-Yao Tan

Journal of Electrochemistry

An intermediate temperature solid oxide fuel cell (IT-SOFC) was fabricated by co-copressing-sintering methods, and the electrolyte of Ce_0.8Gd_0.2O_1.9 (CGO) and cathode materials of La_0.6Sr_0.4Co_0.2Fe_0.8O_3-α (LSCF) were prepared by sol-gel method. The effect of preparation methods on the microstructure of the prepared fuel cells was analyzed by SEM . It shows that the cells prepared by the co-pressing/co-sintering method possess a dense electrolyte layer and a compact interface between electrolyte and anode but a curved configuration, while those prepared by the colloidal technique have a flat configuration …

Study On An Intermediate Temperature Planar Solid Oxide Fuel Cell, Shao-Rong Wang, Wen-Xia Chen, Ting-Lian Wen, Jia-Di Cao, Zhi-Yi Lv, Da-Qian Wang

Journal of Electrochemistry

Tape cast method was applied to prepare green sheets of Ni/YSZ anode supported YSZ thin film. After isostatic pressure treatment and cosintering, the YSZ film on the Ni/YSZ anode was gas-tight dense, and 15~30 μm thick. The area of the composite film was over 100 cm². A Ce_0.8Sm_0.2O_1.9 (CSO) interlayer was sintered on to the YSZ electrolyte film to protect La_0.6Sr_0.4CoO₃ (LSCO) cathode from reaction with YSZ at high temperatures. The LSCO cathode layer was screen printed onto the CSO interlayer and sintered at 1200 ℃ for 3 …

Wavelenght-Dispersive X-Ray Flourescence Accuration, H. Widyatmoko

Makara Journal of Technology

Wavelenght–Dispersive X-Ray Flourescence Accuration. X-Fuorescence spectrometry is a method, which is increasingly applied in the geochemical analysis. X-Fuorescence spectrometry is classified under two categories – WDXRF (wavelenght – dispersive X-ray fluorescence spectrometer) and EDXRF (energy-dispersive X – ray fluorescence spectrometer). WDXRF can be configured as a sequential spectrometer , a simultaneous spectrometer or a hibrid instrument, which combines the advantages of the simultaneous and sequential spectrometers into one instrument. Each instrument is different in some characteristics, and each has applications for which it is specifically suited. In this investigation sequential spectrometer PW 1450 was used to analyze the major, minor …

Secondary Flow Experimental Study For Axial Compressor Cascade Strong Stagger With And Without Tip- Clearance: Static Pressure Distribution On Blade Surface, Syamsuri Syamsuri

Makara Journal of Technology

Secondary Flow Experimental Study for Axial Compressor Cascade Strong Stagger With and Without Tip- Clearance: Static Pressure Distribution on Blade Surface. The performance of blade cascade is influenced by the growth and boundary layer’s separation along blade surface and endwall (casing and hub). The secondary flow which happens near hub and casing compressors is three dimentional flow separation phenomenon comes from interaction blade boundary layer with casing and hub boundary layers in the compressor. The secondary flow causes secondary losses, blockage effect, and turning angle (deflection) distribution along blade span. The result of the research shows that the increase of …

Effect Of Photoperiodicity On Co2 Fixation By Chlorella Vulgaris Buitenzorg In Bubble Column Photobioreactor For Food Supplement Production, Anondho Wijanarko, Dianursanti Dianursanti, Arief Budi Witarto, Roekmijati Widaningroem Soemantojo

Makara Journal of Technology

To reduce the level of CO2 content in air, effort on converting CO2 to useful products is required. One of the alternatives includes CO2 fixation to produce biomass using Chlorella vulgaris Buitenzorg. Chlorella vulgaris Buitenzorg is applied for production of food supplement. Chlorella vulgaris Buitenzorg is also easy to handle due to its superior adaptation. Currently, Chlorella vulgaris Buitenzorg has been analyzed by some experts for its cellular composition, its ability to produce high quality biomass and the content of essential nutrition. A series of experiments was conducted by culturing Chlorella vulgaris Buitenzorg using Beneck medium in bubbling column photobioreactor. …