Engineering Commons^™

Thrust Measurement Of Dielectric Barrier Discharge Plasma Actuators And Power Requirements For Aerodynamic Control, Joseph William Ferry

Masters Theses

"Plasma-based aerodynamic actuators are of interest to researchers because they do not require moving control surfaces or a source of pressurized air to modify a flow field. Dielectric barrier discharge (DBD) plasma actuators have the added advantages of simple installation and low power consumption.

DBD plasma actuators are AC devices. This work measured actuator power consumption and thrust production for driving frequencies between 1 and 18 kHz, and for driving voltages of 6 and 9 kV peak to peak. The actuator consumed between 3 and 22 W of power and produced thrust levels between 0.05 and 0.2 mN per meter …

Laminar-Turbulent Transition For Attached And Separated Flow, Qian Zhang

University of Kentucky Doctoral Dissertations

A major challenge in the design of turbomachinery components for aircraft gas turbine engines is high cycle fatigue failures due to flutter. Of particular concern is the subsonic/transonic stall flutter boundary which occurs at part speed near the stall line. At these operating conditions the incidence angle is large and the relative Mach number is high subsonic or transonic. Viscous effects dominate for high incidence angles.

In order to predict the flutter phenomena, accurate calculation of the steady and unsteady aerodynamic loading on the turbomachinery airfoils is necessary. The development of unsteady aerodynamic models to predict the unsteady forces and …

Fusion Of Imprecise Qualitative Information, Florentin Smarandache, Xinde Li, Xianzhong Dai, Jean Dezert

Branch Mathematics and Statistics Faculty and Staff Publications

In this paper, we present a new 2-tuple linguistic representation model, i.e. Distribution Function Model (DFM), for combining imprecise qualitative information using fusion rules drawn from Dezert-Smarandache Theory (DSmT) framework. Such new approach allows to preserve the precision and efficiency of the combination of linguistic information in the case of either equidistant or unbalanced label model. Some basic operators on imprecise 2-tuple labels are presented together with their extensions for imprecise 2-tuple labels. We also give simple examples to show how precise and imprecise qualitative information can be combined for reasoning under uncertainty. It is concluded that DSmT can deal …

Processing Of Zrb2-Zrc-Zrxsiy Ceramic By Reactive Metal Penetration, Nischel B. Maheswaraiah

Open Access Theses & Dissertations

The processing of ZrB2-ZrC-ZrxSiy composite by reactive metal penetration was investigated as a successor to the ZrB2-SiC composites for hypersonic vehicles application, which cannot be used for extended time at temperatures greater than 1600C due to formation of SiO and CO gases. Zirconium (Zr), zirconium disilicide (ZrSi2), and boron carbide (B4C) were reacted in graphite crucibles for 60, 120, 180, and 240 minutes. Microscopy and x-ray diffraction (XRD) deduced the formation of a heterogeneous microstructure of ZrB2-ZrC-ZrxSiy precipitates surrounded by a solidified Zr-Si melt. Unreacted boron carbide was observed in samples held at 1860C for 60 minutes and 120 minutes, …

Microstructure Investigation Of Al-Rich Titanium Aluminum Alloys, David Pham

Open Access Theses & Dissertations

The microstructures of Ti-Al alloys with 70-80 wt% Al were investigated. Aluminum wire (99.999%) and TiH₂ powder (99.7%) were used to produce the sample compositions inside a vertical tube furnace at 1600^oC in an Ar atmosphere. Argon is purified through a dehumidification and deoxidation system. Magnesium perchlorate Mg(ClO₄)₂ acts as a desiccant and titanium sponge pulls oxygen from the Ar in furnaces operating at 800^oC and 750^oC. X-ray diffraction and an optical microscope are used to identify phases and compositions

Development Of A Micro-Catbed For Miniature Thrusters, Chance Paul Garcia

Open Access Theses & Dissertations

The goal of this work is to develop a micro catalytic bed for miniature thrusters. A test bed was constructed for experimental testing to characterize several parts of the micro catalytic bed. The reactant fluid studied is 90% Hydrogen Peroxide (H2O2) by weight. Three different cross sectional area designs were tested to determine decomposition efficiency, temperature reaction propensity, optimum flow rate, and temperature distribution across each bed. The products of decomposition were condensed to measure the oxygen released from decomposition. The results will be used to develop the basis for a micro catalytic bed design to implement into future miniature …

Influence Of Interactions Between Turbulence And Radiation On Transmissivities In Hypersonic Turbulent Boundary Layers, A. M. Feldick, L. (Lian) Duan, M. F. Modest, M. P. Martín, D. A. Levin

Mechanical and Aerospace Engineering Faculty Research & Creative Works

In the current paper, a high-fidelity large eddy simulation solver is coupled to our modified line-by-line radiative transport equation solver to study the effects of absorption turbulence-radiation interations in a hypersonic turbulent boundary layer, representative of the Orion CEV entering Earth's atmosphere, at peak heating condition. The turbulent and radiation fields represent extreme conditions typical of Orion, as the simulated boundary layer represents the region of high turbulence coupled to region of highest incident radiation. A simplification in the calculation of molecular spectra with a single temperature property database in allows for tractable calculation of spectral properties. A comparison of …

Direct Numerical Simulation Of Hypersonic Turbulent Boundary Layers. Part 2. Effect Of Wall Temperature, L. (Lian) Duan, I. Beekman, M. P. Martín

Mechanical and Aerospace Engineering Faculty Research & Creative Works

In this paper, we perform direct numerical simulation (DNS) of turbulent boundary layers at Mach 5 with the ratio of wall-to-edge temperature T w/T ℘ from 1.0 to 5.4 (Cases M5T1 to M5T5). The influence of wall cooling on Morkovin's scaling, Walz's equation, the standard and modified strong Reynolds analogies, turbulent kinetic energy budgets, compressibility effects and near-wall coherent structures is assessed. We find that many of the scaling relations used to express adiabatic compressible boundary-layer statistics in terms of incompressible boundary layers also hold for non-adiabatic cases. Compressibility effects are enhanced by wall cooling but remain insignificant, and the …

Black Carbon Over Mexico: The Effect Of Atmospheric Transport On Mixing State, Mass Absorption Cross-Section, And Bc/Co Ratios, R. Subramanian, G. L. Kok, D. Baumgardner, A. Clarke, Y. Shinozuka, T. L. Campos, C. G. Heizer, B. B. Stephens, B. De Foy, Paul B. Voss, R. A. Zaveri

Engineering: Faculty Publications

A single particle soot photometer (SP2) was operated on the NCAR C-130 during the MIRAGE campaign (part of MILAGRO), sampling black carbon (BC) over Mexico. The highest BC concentrations were measured over Mexico City (sometimes as much as 2μg/m3) and over hillfires to the south of the city. The age of plumes outside of Mexico City was determined using a combination of HYSPLIT trajectories, WRF-FLEXPART modeling and CMET balloon tracks. As expected, older, diluted air masses had lower BC concentrations. A comparison of carbon monoxide (CO) and BC suggests a CO background of around 65 ppbv, and a background-corrected BC/COnet …

Studies Of Dynamic Crack Propagation And Crack Branching With Peridynamics, Youn Doh Ha, Florin Bobaru

Department of Engineering Mechanics: Faculty Publications

In this paper we discuss the peridynamic analysis of dynamic crack branching in brittle materials and show results of convergence studies under uniform grid refinement (m-convergence) and under decreasing the peridynamic horizon (δ-convergence). Comparisons with experimentally obtained values are made for the crack-tip propagation speed with three different peridynamic horizons.We also analyze the influence of the particular shape of themicro-modulus function and of different materials (Duran 50 glass and soda-lime glass) on the crack propagation behavior. We show that the peridynamic solution for this problem captures all the main features, observed experimentally, of dynamic crack propagation and branching, as well …

Compact Survey And Inspection Day/Night Image Sensor Suite For Small Unmanned Aircraft Systems (Eyepod), Alan Bird, Scott A. Anderson, Dale Linne Von Berg, Morgan Davidson, Niel Holt, Melvin Kruer, Michael L. Wilson

Space Dynamics Laboratory Publications

EyePod is a compact survey and inspection day/night imaging sensor suite for small unmanned aircraft systems (UAS). EyePod generates georeferenced image products in real-time from visible near infrared (VNIR) and long wave infrared (LWIR) imaging sensors and was developed under the ONR funded FEATHAR (Fusion, Exploitation, Algorithms, and Targeting for High-Altitude Reconnaissance) program. FEATHAR is being directed and executed by the Naval Research Laboratory (NRL) in conjunction with the Space Dynamics Laboratory (SDL) and FEATHAR’s goal is to develop and test new tactical sensor systems specifically designed for small manned and unmanned platforms (payload weight < 50 lbs). The EyePod suite consists of two VNIR/LWIR (day/night) gimbaled sensors that, combined, provide broad area survey and focused inspection capabilities. Each EyePod sensor pairs an HD visible EO sensor with a LWIR bolometric imager providing precision geo-referenced and fully digital EO/IR NITFS output imagery. The LWIR sensor is mounted to a patent-pending jitter-reduction stage to correct for the high-frequency motion typically found on small aircraft and unmanned systems. Details will be presented on both the wide-area and inspection EyePod sensor systems, their modes of operation, and results from recent flight demonstrations.

Pilot Source Study: An Analysis Of Pilot Backgrounds And Subsequent Success In Us Regional Airline Training Programs, Guy M. Smith, David A. Newmyer, Elizabeth Bjerke, Mary Niemczyk, Raymond A. Hamilton

Applied Aviation Sciences - Daytona Beach

The 2010 Pilot Source Study, commissioned to research the success of pilots in initial training for Part 121 operations, analyzed the training performance of 2,156 new-hire pilots in the years 2005-2009. Six regional airlines provided data that was mined from human resource and pilot training files. Five university researchers independently analyzed the data and integrated their results. The study expressed success in terms of fewer extra training events and fewer non-completions in regional airline training. Statistically, the best performing pilots were those who had flight instructor certificates, graduated from collegiate accredited flight programs, received advanced (post-Private) pilot training in college, …

Real-Time On-Board Object Tracking For Cooperative Flight Control, Ajay Kumar Mandava, Emma Regentova, Henry Selvaraj

Electrical & Computer Engineering Faculty Research

One of possible cooperative Situations for flights could be a scenario when the decision on a new path is taken by A Certain fleet member, who is called the leader. The update on the new path is Transmitted to the fleet members via communication That can be noisy. An optical sensor can be used as a back-up for re-estimating the path parameters based on visual information. For A Certain topology, the issue can be solved by continuous tracking of the leader of the fleet in the video sequence and re-adjusting parameters of the flight, accordingly. To solve such a problem …

Active Control Of Shocks And Sonic Boom Ground Signal, Bedri Yagiz

Mechanical & Aerospace Engineering Theses & Dissertations

The manipulation of a flow field to obtain a desired change is a much heightened subject. Active flow control has been the subject of the major research areas in fluid mechanics for the past two decades. It offers new solutions for mitigation of shock strength, sonic boom alleviation, drag minimization, reducing blade-vortex interaction noise in helicopters, stall control and the performance maximization of existing designs to meet the increasing requirements of the aircraft industries. Despite the wide variety of the potential applications of active flow control, the majority of studies have been performed at subsonic speeds. The active flow control …

Solution Approximation For Atmospheric Flight Dynamics Using Volterra Theory, Ashraf Mohammed Kandeel Omran

Mechanical & Aerospace Engineering Theses & Dissertations

This dissertation introduces a set of novel approaches in order to facilitate and enrich Volterra theory as a nonlinear approximation technique for constructing mathematical solutions from the governing relationships describing aircraft dynamic behavior. These approaches reconnect Volterra theory and flight mechanics research, which has not been addressed in the technical literature for over twenty years. Volterra theory is known to be viable in modeling weak nonlinearities, but is not particularly well suited for directly describing high performance aircraft dynamics. In order to overcome these obstacles and restrictions of Volterra theory, the global Piecewise Volterra Approach has been developed. This new …

Analysis Of Wake Vortices Of A Medium Range Twin-Propeller Military Cargo Aircraft Using Statistically Designed Experiments, Burhan Sahin

Mechanical & Aerospace Engineering Theses & Dissertations

An experimental study was initiated to analyze the trajectories of the streamwise vortices behind the wing tip and flap of a medium range and propeller driven twin-engine military cargo aircraft. The model used for the experimental study was a generic, high wing and half model of a propeller driven aircraft and mounted within Old Dominion University's Low Speed Wind Tunnel where the wind tunnel flow speed was set to constant value of 9 m/sec. The main purpose of the study was to reach regression models for the motion and vorticity strength of both vortices under varying factors such as angle …

Constrained Optimal Orbit Design For Earth Observation, Sharon D. Vtipil

Mechanical & Aerospace Engineering Theses & Dissertations

The purpose of this dissertation is to demonstrate use requirements for a satellite observation mission can be used to determine a constrained optimal orbit based on observation site requirements, observation condition restraints, and sensor characteristics. The typical Earth observation satellite is first designed according to an appropriate orbit; then the observation requirements are used to develop a target schedule. The new design process outlines the development of the appropriate orbit by incorporating user requirements at the forefront of mission planning, not after an orbit has been selected. This research shows how to map the user requirements into constraints for the …

Discrete Film Cooling In A Rocket With Curved Walls, Jonathan F. Mccall

Theses and Dissertations

This study quantified the effects of discrete wall-based film cooling in a rocket with curved walls. Simulations and experiments showed decreasing with wall radius of curvature, holding jet diameter constant, improves net heat flux reduction (NHFR) and adiabatic effectiveness (η) for 90˚ compound injected cylindrical jets, though η is reduced at the highest curvature. NHFR and η improved further with a high favorable stream-wise pressure gradient (K=2.1x10^-5) at all tested blowing ratios, but were affected little by a high density ratio (DR=1.76) using carbon dioxide as the coolant. Experiments were run at a Reynolds number of 31K and …

Laser-Induced Fluorescence And Synthetic Jet Fuel Analysis In The Ultra Compact Combustor, Aaron C. Drenth

Theses and Dissertations

The Ultra-Compact Combustor (UCC) is currently under investigation at the Air Force Institute of Technology (AFIT) and Air Force Research Laboratory’s Propulsion Directorate. The combustor is a small-scale, axi-symmetric, atmospheric pressure, laboratory combustor with an outer circumferential cavity in which the flame is stabilized by a highly accelerated swirled flow. UCCs will enable aero gas turbine reheat cycle engines and significantly shorten conventional aero gas turbine engines. The experiments of this work utilized the AFIT small-scale combustion diagnostics facility, investigating a sector model of the UCC. The research objectives were to perform an addition to the COAL lab laser diagnostic …

Flow Measurements Using Particle Image Velocimetry In The Ultra Compact Combustor, Levi M. Thomas

Theses and Dissertations

Velocity measurements were performed using the Particle Image Velocimetry (PIV) technique on the Ultra Compact Combustor (UCC) test rig at the Air Force Institute of Technology (AFIT). Velocity patterns and time-averaged turbulence statistics were calculated for data taken with the UCC burning hydrogen fuel in the straight cavity vane and curved cavity vane configurations. The equivalence ratio was varied from 0.7 to 1.5, while the ratio of cavity air to main air was varied from 5% to 20% in testing performed on the straight vane configuration. Spanwise velocity was observed to decrease linearly with distance from the cavity vane over …

Investigation Into Contact Resistance And Damage Of Metal Contacts Used In Rf-Mems Switches, Kevin W. Gilbert

Theses and Dissertations

This research examines the physical and electrical processes involved in lifecycle failure of Microelectromechanical (MEMS) Radio-Frequency (RF) cantilever beam ohmic contact switches. Failures of these switches generally occur at the contact, but complete details of performance of microcontacts are difficult to measure and have not been previously reported. This study investigated the mechanics of microcontact behavior by designing and constructing a novel experimental setup. Three representative contact materials of varying microstructure (Au, Au5%Ru, Au4%V₂O₅) were tested and parameters of contact during cycling were measured. The Au4%V₂O₅, a dispersion strengthened material developed at …

Fatigue Behavior Of An Advanced Sic/Sic Composite At Elevated Temperature In Air And In Steam, Devon T. Christensen

Theses and Dissertations

The fatigue behavior of an advanced Silicon Carbide/Silicon Carbide (SiC/SiC) ceramic matrix composite (CMC) was investigated at 1200 ˚C in laboratory air and in steam environments. The composite consisted of a SiC matrix reinforced with Boron Nitride (BN) coated Hi-Nicalon fibers woven into eight-harness-satin (8HS) weave plies. Tensile stress-strain behavior and tensile properties were also evaluated at 1200 ˚C. Tension-tension fatigue tests were conducted in both laboratory air and in steam at 1200 ˚C at frequencies of 0.1 Hz, 1.0 Hz, and 10 Hz. The tension-tension fatigue tests had a ratio of minimum stress to maximum stress of R = …

Flow Visualization Study Of Passive Flow Control Features On A Film-Cooled Turbine Blade Leading Edge, Daniel R. Carroll

Theses and Dissertations

A flow visualization study was conducted on a model of a film-cooled turbine blade leading edge in a closed-loop water channel at Re_D = 30k. The model consisted of an 8.89 cm diameter half-cylinder with flat afterbody joined at the ninety degree point. A single radial coolant hole (d_c / D = 0.054) drilled 21.5° from the stagnation line, angled 20° to the surface and 90° to the flow direction generated a coolant jet transverse to the freestream. Water channel testing assessed the hydrodynamic effects of 16 passive flow control features, to include a variety of …

Avoiding Overrun Accidents On Contaminated Runways, Nihad E. Daidzic

Aviation Department Publications

No abstract provided.

Removal Of Biofilm Through Controlled Cavitation, Mathew Chackalackal Mathew

Master's Theses - Daytona Beach

Human kind is poised to take the next "giant step" in space exploration, the manned mission to Mars, among other things. But before any plans for such long term habitation on an alien planet, there has to be consideration towards prevention and removal of bacterial contamination. Bacterial contamination or rather degradation of materials was considered of negligible importance. Bacterial degradation can be serious for long-term manned space mission, more so because there is no way to obtain quick replacements. For such conditions, a new innovative way of bacterial removal has been proposed wherein the bacteria is removed with no damage …

A Domain-Specific Design Tool For Verifying Spacecraft System Behavior, Sravanthi Venigalla

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

In this report we present a graphical tool, Behavioral Analysis of Spacecraft Systems (BASS), that can be used by spacecraft designers to perform system-level behavioral analysis of small satellites. The domain-specific spacecraft meta-model is created in the visual modeling tool Generic Modeling Environment (GME) such that spacecraft designs created using the meta-model appear familiar to the spacecraft designers. Users can model scenarios that are to be verified for the design in BASS. The graphical models are assigned formal semantics facilitating the creation of formally verifiable spacecraft models. The C++ application that translates the modeling objects to equivalent mathematical representation of …

Interim Access To The International Space Station, Tyson Karl Smith

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

This thesis evaluates mission scenarios using the existing Evolved Expendable Launch Vehicles for delivering the Crew Exploration Vehicle to the International Space Station. The Space Shuttle is scheduled to retire in the year 2011 and the Ares I is being developed to replace it. With its current schedule, the earliest that the Ares I will become fully operational is 2016. The configurations in this thesis are presented to narrow the gap in which the USA does not have direct access to the International Space Station. They also present "buy down" options for the USA human space operations, if the current …

Spatial Instability Of Electrically Driven Jets With Finite Conductivity And Under Constant Or Variable Applied Field, Saulo Orizaga, Daniel N. Riahi

Applications and Applied Mathematics: An International Journal (AAM)

We investigate the problem of spatial instability of electrically driven viscous jets with finite electrical conductivity and in the presence of either a constant or a variable applied electric field. A mathematical model, which is developed and used for the spatially growing disturbances in electrically driven jet flows, leads to a lengthy equation for the unknown growth rate and frequency of the disturbances. This equation is solved numerically using Newton’s method. For neutral temporal stability boundary, we find, in particular, two new spatial modes of instability under certain conditions. One of these modes is enhanced by the strength Ω of …

Grating Lobe Reduction In Aperiodic Linear Arrays Of Physically Large Antennas, William C. Barott, Paul G. Steffes

Publications

We present performance bounds obtained from the optimization of the sidelobe levels of aperiodic linear arrays. The antennas comprising these arrays are large compared to the distance between neighboring antennas, a case not addressed in previously published work. This optimization is performed in pattern-space and is applicable over a wide range of scan angles. We show that grating lobes can be suppressed even when the elemental antennas are several wavelengths in size, provided that the ratio of the antenna size to the average spacing between the antenna center-points does not exceed 80%.

The Part Count Tool (Pact) For Concept Selection, Tarang Parashar, Katie Grantham Lough, Robert B. Stone

Engineering Management and Systems Engineering Faculty Research & Creative Works

This paper presents a part count tool that automates the consideration of manufacturing cost during the conceptual design phase by predicting part count for a particular product concept. with an approximate number of parts per product in the conceptual design phase, the designer can estimate the cost associated with the product. on the basis of the cost, the designer can make changes according to budget requirements. the part count tool will also aid in ranking the design concepts by number of components for a product. This tool utilizes existing automated concept generation algorithms to generate the design concepts. It extracts …