Engineering Commons^™

Degradation Of Solar Cells Due To Arcing In A Vacuum Chamber, Christina Gonzalez

Aerospace Engineering

This report summarizes the senior project entitled Degradation of Solar Cells Due to Arcing in a Vacuum Chamber. The goal of this experiment was to show electrical and physical degradation of silicon solar cells in a vacuum chamber. The cells were characterized and then placed in a vacuum chamber. Under vacuum, a potential was created to induce arcing to the cell. The cell was characterized again after arcing to determine the change in efficiency. This document details the process for designing the circuit to create the arcing, and the different setups used to degrade the cells electrically and physically. It …

The Study Of Natural Composite I-Beam In A Three Point Bending Test, Abdel Shabbar

Aerospace Engineering

The objective of this experiment is to conduct a series of unidirectional tensile test on several samples of natural occurring plant fibers. Among the materials tested, hemp has proven to be the most promising candidate as the base material in creating an all-natural composite I-Beam. This I-Beam will be entered into the annual SAMPE 2012 competition to compete against other schools and universities nationwide. These I-Beams will undergo a three point bending test, and must withstand the greatest load whilst remaining in the parameters set by SAMPE. This I-Beam will go on to take third place internationally. In addition, the …

Flaperon Assembly Manual For Pegastol Aftermarket Wings, Eric Alan Gray

Aerospace Engineering

No abstract provided.

Assembly Of A Passive Slat System For A Ch-701 Kit Aircraft, Jordan Coenen, Spencer Spagnola

Aerospace Engineering

No abstract provided.

Computation Time Comparison Between Matlab And C++ Using Launch Windows, Tyler Andrews

Aerospace Engineering

Processing speed between Matlab and C++ was compared by examining launch windows and handling large amounts of data found in pork chop plots. A compilation of code was generated in Matlab to produce the plots and an identical file was created in C++ that was then compiled and run in Matlab to plot the data. This file is known as a MEX-file. This report outlines some of the basics when working with MEX-files and the problems that face users. For Lambert’s solver, multi revolution cases were considered and some pork chop plots of single revolution trajectories were plotted. Three different …

Preliminary Design Of A Laboratory Cylindrical Hall-Effect Thruster, Scott Mcgrail, Sam Parker

Aerospace Engineering

A 3-cm cylindrical Hall thruster with permanent magnets was designed and modeled. The goal was to design a Hall thruster for Cal Poly’s propulsion laboratory of similar size and performance as Cal Poly’s MiXI thruster. The design process began with an investigation into the physics of Hall thrusters and selection of certain thruster parameters. The selected parameters were the diameter and depth of the channel, the total power input to the system, the discharge supply voltage, the cathode voltage, and the propellant flow rates to the anode and cathode. These parameters were used to determine the operational characteristics of the …

Data Acquisition For Flight Tests Using Handheld Gps And Electronic Flight Instrument System, Christopher Michael Gocha

Aerospace Engineering

No abstract provided.

Reliable Software Updates For On-Orbit Cubesat Satellites, Sean Fitzsimmons

Master's Theses

CubeSat satellites have redefined the standard solution for conducting missions in space due to their unique form factor and cost. The harsh environment of space necessitates examining features that improve satellite robustness and ultimately extend lifetime, which is typical and vital for mission success. The CubeSat development team at Cal Poly, PolySat, has recently redefined its standard avionics platform to support more complex mission capabilities with this robustness in mind. A significant addition was the integration of the Linux operating system, which provides the flexibility to develop much more elaborate protection mechanisms within software, such as support for remote on-orbit …

Human Powered Helicopter: Rotor Structure, Joseph Ram, Juan Carlos Olvera

Mechanical Engineering

The following report encompasses the Human Powered Helicopter Rotor Team’s conceptual models and ideas based on research and modeling analysis. The following gives an overview of material researched, concept generation, analyzation, manufacturing, and testing for a rotor structure to be installed in a Human Powered Helicopter.

Aerodynamic Test Platform For Human Powered Vehicle (Hpv), Spencer Wangerin, Spencer Lillywhite, Colburn Davis

Mechanical Engineering

The Aerodynamic Test Platform (ATP) for the Cal Poly HPV Club is a system that was designed by Cal Poly mechanical engineering students to measure aerodynamic characteristics of a human-powered vehicle (HPV). The HPV team desired a system that could quantify the lift, drag, and other aerodynamic qualities of a full scale HPV at various orientations in oncoming airflow. Established methods for determining aerodynamic characteristics include computational fluid dynamics (CFD) and wind tunnel testing of scaled models. The ATP was devised to simulate the test results given by a full-scale wind tunnel without requiring a wind tunnel large enough to …

Development Of A Ground Based Atomic Oxygen And Vacuum Ultraviolet Radiation Simulation Apparatus, Max Jay Glicklin

Master's Theses

The space environment possesses numerous unique and unusual attributes, creating challenges that must be considered in order to accomplish a successful space mission. Two of the detrimental aspects of the space environment include Atomic Oxygen, AO, and Ultraviolet, UV, radiation. UV radiation becomes more severe in space as there is no atmosphere to attenuate incoming photons, thereby exposing spacecraft to radiation that never reaches the surface of the Earth. Overall, space vehicles are exposed to a total of 107.4 Watts/m² of light shorter than 400 nm. AO is created by the photo disassociation of molecular oxygen by UV radiation …

Registering An Amateur-Built Light Sport Kit Aircraft, Kevin Condron

Aerospace Engineering

No abstract provided.

Day/Night Band Imager For A Cubesat, Eric Stanton

Electrical Engineering

Day/Night Band (DNB) earth sensing and meteorological systems like the Defense Meteorological Satellite Program (DMSP) Operational Linescan System (OLS) provide visible wavelength imagery 24 hours a day that is used primarily for cloud imaging in support of weather forecasting. This paper describes a compact push-broom imager that meets low light imaging requirements for DMSP OLS and the NOAA/NASA Joint Polar Satellite System (JPSS) as documented in the Integrated Operational Requirements Document [1] (IORD) including the imager design, system level concepts of operation for data collection, radiometric and spatial calibration, and data transmission to Earth. This small, lightweight imager complies with …

Design Of A Human Powered Helicopter Airframe, Sheen Kao, Daniel Layton, Philip Sobol

Mechanical Engineering

In 1989 Cal Poly’s Da Vinci III was the first human powered helicopter (HPH) to achieve flight; our goal is to research and develop a new airframe for the next generation Da Vinci. This report outlines a brief history of human powered flight and details a method of constructing for the airframe. An optimized airframe geometry was also researched and is explained in detail.

An Experimental Investigation Of Glare And Restructured Fiber Metal Laminates, Adelina Vanessa Benedict

Doctoral Dissertations and Master's Theses

Fiber Metal Laminates (FMLs) are a group of materials fabricated by bonding glass/epoxy layers within metal layers. This class of materials can provide good mechanical properties, as well as weight savings. An FML known as Glass Laminate Aluminum Reinforced Epoxy (GLARE) was studied. An experimental investigation comprising of microscopy and tensile testing was carried out using different grades of GLARE. Microscopy revealed the construction details of GLARE, while tensile testing provided means of measuring and analyzing its stress-strain responses. Next, different metal surface pretreatment methods were explored. These included sandblasting, Phosphoric Acid Anodizing (PAA), and AC-130 Sol-Gel treatment. Woven S-2 …

Cubesat Mission Planning Toolbox, Brian Castello

Master's Theses

We are in an era of massive spending cuts in educational institutions, aerospace companies and governmental entities. Educational institutions are pursuing more training for less money, aerospace companies are reducing the cost of gaining ight heritage and the government is cutting budgets and their response times. Organizations are accomplishing this improved efficiency by moving away from large-scale satellite projects and developing pico and nanosatellites following the CubeSat specifications. One of the major challenges of developing satellites to the standard CubeSat mission requirements is meeting the exceedingly tight power, data and communication constraints.

A MATLAB toolbox was created to assist the …

Feasibility Study Into The Use Of 3d Printed Materials In Cubesat Flight Missions, Daniel Fluitt

Master's Theses

The CubeSat Program has provided access to space for many universities, private companies, and government institutions primarily due to the low cost of CubeSat satellite development. While these costs are orders of magnitude lower than similarly capable nano-satellite missions, they are still outside of the budgetary constraints of many potential developers including university and high school clubs. Using 3D printed plastics in the production of CubeSat structures and mechanisms presents a large cost savings opportunity that will allow these institutions to participate in the development of these satellites, expanding the educational and scientific impact of the CubeSat Program.

Five rapid …

Implementation Of A ¼ Inch Hollow Cathode Into A Miniature Xenon Ion Thruster (Mixi), David Wayne Knapp

Master's Theses

Over the last decade, miniature ion thruster development has remained an active area of research do to its low power, low thrust, and high efficiency, however, due to several technical issues; a flight level miniature ion thruster has proved elusive. This thesis covers the design, fabrication, assembly, and test of an altered version of the Miniature Xenon Ion thruster (MiXI), originally developed by lead engineer Dr. Richard Wirz, at the California Institute of Technology (Caltech). In collaboration with Dr. Wirz, MiXI-CP-V3 was developed at Cal Poly San Luis Obispo with the goal of implementing of a ¼ inch hollow cathode …

Hapss, Hybrid Aircraft Propulsion System Synthesis, Michael W. Green

Master's Theses

Hybrid Aircraft Propulsion System Synthesis (HAPSS) is a computer program that sizes and analyzes pure-series hybrid electric propulsion systems for aircraft. The development of this program began during a NASA SBIR contract, in conjunction with Empirical Systems Aerospace (ESAero), with the creation of a propulsion fan design tool. Since the completion of this contract in July 2010, the HAPSS program has been expanded to combine the many aspects of a hybrid propulsion system such as the propulsive fans, electric motors, generators, and controllers, and the internal combustion engines.

This thesis describes the benefits and drawbacks of aircraft hybrid propulsion systems …

Modal Analysis Of Composite Structures With Damping Material, Kellie Michelle Tremaine

Master's Theses

The purpose of this study is to develop an analytical solution for modal analysis of actively damped orthotropic composite plates in bending and to verify it with experimental analysis.

The analytical modal analysis solution for composite plate dynamics is derived using Euler theory. This analysis applies to structures with orthotropic lamina of uniform material properties at any lamination angle. The bending-extensional coupling can be neglected for plates that are symmetric or approximately symmetric, which allows an exact solution for natural frequency and mode shape to be obtained. An exact solution can be found for natural vibration and in general.

The …

An Investigation Of Damage Arrestment Devices On Carbon Fiber Sandwich Specimens Under Dynamic Loading, Gabriel Sabino Sanchez

Master's Theses

This research studies the effects of a damage arrestment device embedded between a carbon fiber facesheet and foam core to find whether there is an increase in the structural integrity of the sandwich composites. Experimental and theoretical finite element analyses are implemented for two different composite sandwich geometries; plates and beams. Each structure consisted of the same loading criteria and was restricted to the same vibration fixture during the experiment. An accelerometer was placed on the composite plate to record the amplitude and the natural frequencies of the composite structure. Each composite specimen is then fixed to the surface of …

Flying Qualities Built-In-Test For Unmanned Aerial Systems, Alton Pak-Hin Chiu

Master's Theses

This paper presents a flying qualities built-in-test for UAS application with the scope limited to the longitudinal axis. A doublet input waveform excites the AV and both α and q are used by EUDKF to estimate the A and B matrices which are short period approximations of the system. ζ, ω, GM, PM, observability, and controllability are calculated to determine flying qualities with the results displayed to the AVO in a color-coded, easy to interpret display.

While SID algorithms have been flying in vehicles with adaptive control schemes, vehicles with other schemes (such as classical feedback) lack this built-in self …

Activity Node Based Flight Software As A Benefit To Systems Engineering, Eugene Daniel Lewis

Master's Theses

This report discusses one application of a flight software design for a spacecraft in which the software executes from a database that can be managed by systems engineering. This report gives an overview of how such a software design can be developed and implemented. It also discusses why this approach is beneficial to the systems engineering program.

Analysis And Testing Of Heat Transfer Through Honeycomb Panels, Daniel D. Nguyen

Aerospace Engineering

This project attempts to simulate accurately the thermal conductivity of honeycomb panels in the normal direction. Due to the large empty space of the honeycomb core, the thermal radiation mode of heat transfer was modeled along with conduction. Using Newton’s Method to solve for a steady state model of heat moving through the honeycomb panel, the theoretical effective thermal conduction of the honeycomb panel was found, ranging from 1.03 to 1.07 Q/m/K for a heat input of 2.5 W to 11.8 W. An experimental model was designed to test the theoretical results, using a cold plate and a heat plate …

Design Of Orbital Maneuvers With Aeroassisted Cubesatellites, Stephanie Clark

Graduate Theses and Dissertations

Recent advances within the field of cube satellite technology has allowed for the possible development of a maneuver that utilizes a satellite's Low Earth Orbit (LEO) and increased atmospheric density to effectively use lift and drag to implement a noncoplanar orbital maneuver. Noncoplanar maneuvers typically require large quantities of propellant due to the large delta-v that is required. However, similar maneuvers using perturbing forces require little or no propellant to create the delta-v required. This research reported here studied on the effects of lift on orbital changes, those of noncoplanar types in particular, for small satellites without orbital maneuvering thrusters. …

Reduction Of Solid-Solid Thermal Boundary Resistance By Inserting An Interlayer, Zhi Liang, Hai-Lung Tsai

Mechanical and Aerospace Engineering Faculty Research & Creative Works

An Effective Method is Proposed to Greatly Improve the Thermal Transport Across the Interface between Two Solids with Dissimilar Phonon Spectra. If the Two Solids Have Similar Crystal Structure and Lattice Constant, It is Predicted from the Molecular Dynamics Modeling that an over 50% Reduction of the Thermal Boundary Resistance Can Be Achieved by Inserting a 3-Unit-Cell-Thick Interlayer Whose Debye Temperature is Approximately the Square Root of the Product of the Debye Temperatures of the Two Solids. on the Other Hand, If the Two Solids Have a Large Difference in Lattice Constant, It is Found the Interfacial Atomic Restructuring Plays …

Novel Heavy Duty Engine Concept For Operation Dual Fuel H 2-Nh3, Alberto A. Boretti

Mechanical and Aerospace Engineering Faculty Research & Creative Works

A prior paper has presented a novel design of a heavy-duty truck engine fueled with H2. in this design, the customary in-cylinder Diesel injector and glow plug are replaced with a main chamber fuel injector and a jet ignition pre-chamber. the jet ignition pre-chamber is a small volume that is connected to the in-cylinder through calibrated orifices accommodating another fuel injector and a glow or a spark plug that controls the start of combustion. This design permits to operate the engine in four different modes: traditional compression ignition (CI), diffusion, Diesel-like (M1); mixed gasoline/Diesel-like (M2); traditional spark ignition (SI), premixed, …

Evaluation Of Turbulence Variable Distributions For Incompressible Fully Rough Pipe Flows, Emilie B. Fowler

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

The specific turbulent kinetic energy, root-mean-square fluctuating vorticity, and mean-vortexwavelength distributions are presented for fully rough pipe flow. The distributions of these turbulence variables are obtained from a proposed turbulence model. Many of the turbulence models commonly used for computational fluid dynamics are based on an analogy between molecular and turbulent transport. However, traditional k-ε and k-ω models fail to exhibit proper dependence on the molecular viscosity. Based on a rigorous application of the Boussinesq’s hypothesis, Phillips proposed a vorticity-based transport equation for the turbulent kinetic energy. The foundation for this vorticity-based transport equation is presented. In future development of …

Statistical Methods For Launch Vehicle Guidance, Navigation, And Control (Gn&C) System Design And Analysis, Michael Benjamin Rose

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

A new tool for launch vehicle design and analysis is developed. The tool is capable of rapid analysis of requirements tradeoffs affecting system design and developed to reduce turnaround time for launch vehicle design and mission planning. It is streamlined to quickly determine trajectory and attitude control dispersions which represent how far the actual trajectory is expected to deviate from the nominal flight path, propellant dispersions which represent how much propellant is required to meet mission requirements, and navigation errors which represent how far the navigation filter’s estimate of the actual trajectory is expected to deviate from the actual trajectory. …

Effective Thermal Conductivity Of Tri-Isotropic (Triso) Fuel Compacts, Charles P. Folsom

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

The Next Generation Nuclear Plant (NGNP) program objective is to develop a new type of nuclear reactor that produces process heat instead of electricity. The process heat can be used in the production of hydrogen and many other industrial processes. As part of the NGNP program a new type of nuclear fuel is being developed. The fuel is a composite construction of specially coated fuel particles and graphite pressed together in a cylindrical compact.

Thermal conductivity is an important thermophysical property of the fuel that needs to be measured. Knowledge of the thermal conductivity of the fuel will provide accurate …