Engineering Commons^™

Improving Mode Ii Fracture Toughness Of Secondary Bonded Joints Using Laser Patterning Of Adherends, A. Wagih, R. Tao, A. Yudhanto, G. Lubineau

Mechanical and Aerospace Engineering Faculty Research & Creative Works

We improve mode II fracture toughness of secondary bonded joints based on the laser treatment of adherend surfaces. We applied CO₂ Laser treatment to adherend surface alternatively with low and high energy, resulting in a repeated pattern of rough and smooth surfaces. We used ENF test to characterize mode II fracture toughness, GII, of the bonded CFRP substrates. The results demonstrated that our proposed pattern arrested the crack propagation and triggered new damage mechanisms, such as adhesive cracking, adhesive failure and crack migration to the other interface. These additional mechanisms, some of them were non-local in nature, resulted in …

How The Spatial Correlation In Adhesion Properties Influences The Performance Of Secondary Bonding Of Laminated Composites, Xiaole Li, Ran Tao, Arief Yudhanto, Gilles Lubineau

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Spatial heterogeneity of adhesion properties is known to result in bridging during debonding of secondary bonded composite joints. The ligaments that bridge both substrates have crack-arrest features and thus significantly enhance the fracture resistance of joints. We have investigated the effect of randomly distributed adhesion properties between the adhesive layer and each composite substrate in previous works; however, the spatial correlation of adhesion heterogeneity within or between the substrates and how it effects the failure of secondary bonded composites is still poorly understood. In this current work, we assume that the spatial heterogeneity of adhesion follows a log-normal distribution. The …

Piezoresistive Hybrid Nanocomposites For Strain And Damage Sensing: Experimental And Numerical Analysis, Audrey Jean-Miche Gbaguidi

Doctoral Dissertations and Master's Theses

Carbon nanomaterials such as carbon nanotubes (CNTs) and graphite nanoplatelets (GNPs) demonstrate remarkable electrical and mechanical properties, which suggest promising structural and functional applications as fillers for polymer nanocomposites.

The piezoresistive behavior of these nanocomposites makes them ideal for sensing applications. Besides, hybrid nanocomposites with multiple fillers like carbon nanotubes (CNTs) and graphite nanoplatelets (GNPs) are known to exhibit improved electrical and mechanical performance when compared to mono-filler composites.

To comprehensively understand the mechanisms of electrical percolation, conductivity, and piezoresistivity in hybrid nanocomposites, the author develops a two-dimensional (2D) and a three-dimensional (3D) computational Monte Carlo percolation network models for …

Three-Dimensional, Vision-Based Proportional Navigation For Uav Collision Avoidance, Guanhong Gao

Doctoral Dissertations and Master's Theses

As the number of potential applications for Unmanned Aerial Vehicles (UAVs) keeps rising steadily, the chances that these devices will operate in close proximity to static or dynamic obstacles also increases. Therefore, collision avoidance is an important challenge to overcome for Unmanned Aerial Vehicle operations. Electro-optical devices have several advantages such as light weight, low cost, low algorithm requirements with respect to computational power and possibly night vision capabilities. Therefore, vision-based Unmanned Aerial Vehicle collision avoidance has received considerable attention. Although much progress has been made in collision avoidance systems (CAS), most approaches are focused on two-dimensional environments. In order …

An Open Source, Autonomous, Vision-Based Algorithm For Hazard Detection And Avoidance For Celestial Body Landing, Daniel Posada

Doctoral Dissertations and Master's Theses

Planetary exploration is one of the main goals that humankind has established as a must for space exploration in order to be prepared for colonizing new places and provide scientific data for a better understanding of the formation of our solar system. In order to provide a safe approach, several safety measures must be undertaken to guarantee not only the success of the mission but also the safety of the crew. One of these safety measures is the Autonomous Hazard, Detection, and Avoidance (HDA) sub-system for celestial body landers that will enable different spacecraft to complete solar system exploration. The …

Contributions To The Understanding Of Ship Airwakes Using Advanced Flow Diagnostic Techniques, Dhuree Seth

Doctoral Dissertations and Master's Theses

The objective of this research was to better characterize the complex, three dimensional, unsteady aerodynamic flows produced by the superstructure of a ship, which is referred to as an airwake. This problem is relevant and important because the turbulent airwake significantly and adversely affects the ability for rotorcraft to operate safely from the decks of Navy ships. To this end, a series of wind tunnel measurements were performed on the SFS2 simplified frigate shape, which has a flight deck at its stern. The measurements were performed with and without a simulated atmospheric boundary layer (ABL), which included the aerodynamic scaling …

Optimization Of Spacecraft Formations About Lagrange Points For The Next Generation Space Weather Prediction Mission, Roberto Cuéllar Rangel

Doctoral Dissertations and Master's Theses

This thesis’s work serves as proof of concept for the Next Generation Space Weather Prediction Mission, a multi-spacecraft mission at various libration points whose objective is to forecast Space Weather hazards with a 12day warning time. This thesis deals with the design and control of orbits of spacecraft formations at different libration points. The systems studied are SunEarth, SunVenus, SunMercury, and SunMars. The orbit design and formation keeping control of the spacecraft are solved simultaneously using an optimization software called DIDO. Initial conditions are obtained through two different strategies. The first one, by placing the spacecraft in a tetrahedral formation …

Python Implementation Of Batch Least-Squares Filter For Satellite Orbit Determination, Austin Ogle

Doctoral Dissertations and Master's Theses

Accurate orbit determination techniques are fundamental to the maintenance and execution of any ongoing space-based mission. This project serves as a guide and demonstration of a batch sequential least-squares filter for Earth-orbiting satellites using exclusively open-source technologies. The target audience for this project was an academic institution aiming to keep track of an irregularly documented satellite. The observation function mimics a telescope, accepting right ascension and declination as measured values.

State propagation was handled using the Poliastro library. This package boasts FORTRANlevel speed by utilizing the DOPRI8 integrator, explicitly calling FORTRAN code. Matrix inversion was solved using the SciPy banded …

Limitations Of Initial Orbit Determination Methods For Low Earth Orbit Cubesats With Short Arc Orbital Passes, James P. Johnson

Master's Theses

This thesis will focus on the performance of angles only initial orbit determi- nation (IOD) methods on observational data of low Earth orbit (LEO) CubeSats. Using data obtained by Lockheed Martin’s Space Object Tracking (SpOT) facil- ity, four methods: Gauss, Double-R, Gooding and Assumed Circular, will use different amounts of orbital arc to determine which methods perform the best in the short arc regime of less than 10 degrees of orbital arc. Once the best method for estimating the orbit is determined, there will be analysis on whether these IOD methods are accurate enough to predict a secondary observation session. …

Power-Over-Tether Uas Leveraged For Nearly-Indefinite Meteorological Data Acquisition, Daniel Rico, Carrick Detweiler, Francisco Muñoz-Arriola

School of Computing: Dissertations, Theses, and Student Research

Use of unmanned aerial systems (UASs) in agriculture has risen in the past decade. These systems are key to modernizing agriculture. UASs collect and elucidate data previously difficult to obtain and used to help increase agricultural efficiency and production. Typical commercial off-the-shelf (COTS) UASs are limited by small payloads and short flight times. Such limits inhibit their ability to provide abundant data at multiple spatiotemporal scales. In this paper, we describe the design and construction of the tethered aircraft unmanned system (TAUS), which is a novel power-over-tether UAS leveraging the physical presence of the tether to launch multiple sensors along …

All-Metallic Phase Change Thermal Management Systems For Transient Spacecraft Loads, Carl R. Hartsfield, Travis E. Shelton, Brian O. Palmer, Ryan P. O'Hara

Faculty Publications

In this work, we explore the thermal properties of gallium as an effective phase change material for thermal management applications. Thermal storage and dissipation of gallium manufactured heat sinks were compared to conventional phase change heat sinks. The comparison revealed a 50-fold (80 K versus 1.5 K) potential reduction in temperature during the phase change process due to the high density, thermal conductivity, and latent heat of fusion. The gallium creates shallow thermal gradients when transiently heated, producing a nearly isothermal process. Computational estimates using lumped sum parameters were able to provide simple modeling to predict the results. Gallium based …

Rotor-On-Rotor Aeroacoustic Interactions Of Multirotor In Hover, Eduardo Alvarez, Austin Schenk, Tyler Critchfield, Andrew Ning

Faculty Publications

Multirotor configurations introduce complicated aerodynamic and aeroacoustic interactions that must be considered during aircraft design. In this paper we explore two numerical methods to model the acoustic noise caused by aerodynamic rotor-on-rotor interactions of rotors in hover. The first method uses a conventional mesh-based unsteady Reynolds-average Navier-Stokes (URANS) solver, while the second consists of a meshless Lagrangian solver based on the viscous vortex particle method (VPM). Both methods are coupled with an aeroacoustics solver for tonal and broadband noise predictions. Noise predictions are validated for single and multi-rotor configurations, obtaining with the VPM a similar accuracy than URANS while being …

Quantum Frontiers: To Boldly Go, Michael Dixon, Cali Christensen, Rachael Leisek

Space Dynamics Laboratory Publications

We have lift off!

Cali Christensen started her summer at Quantum Frontiers (QF) at an intern lunch. Seated around her were 20 other interns from universities all over the country who had been selected from a pool of over 900 applicants to participate in high-tech, space-related research endeavors pushing the boundaries of various fields such as engineering, mathematics, computer science, machine learning, and physics. Cali quickly realized after the first presentation that she may be one of the only non-engineer or scientists in the room. Her internship was different from any others that QF had yet sponsored. Instead of making …

Topology Optimization And Analysis Of Thermal And Mechanical Metamaterials, Lee Alacoque

Doctoral Dissertations and Master's Theses

To take advantage of multi-material additive manufacturing technology using mixtures of metal alloys, a topology optimization framework is developed to synthesize high-strength spatially periodic metamaterials possessing unique thermoelastic properties. A thermal and mechanical stress analysis formulation based on homogenization theory is developed and is used in a regional scaled aggregation stress constraint method, and a method of worst-case stress minimization is also included to efficiently address load uncertainty. It is shown that the two stress-based techniques lead to thermal expansion properties that are highly sensitive to small changes in material distribution and composition. To resolve this issue, a uniform manufacturing …

Development Of High-Density Propulsion System Technologies For Interplanetary Small Satellites And Cubesats, Morgan Andrew Roddy

Graduate Theses and Dissertations

The goal of this research was to support the development of a novel propulsion system for small satellites (<180 kg) and CubeSats. This was pursued by conducting a collection of studies that were designed to provide engineering data that would be critical in designing a functional prototype. The novel propulsion system was conceived by the author to provide best-in-class performance for the small satellite and CubeSat families of spacecraft. This context presents specific design requirements that the presented technology attempts to satisfy. The most critical among these is high density; the propellant was designed to be stored with high density and the thruster was designed to be as compact as possible. The propulsion system is composed of two primary elements, a propellant generator and a thruster. The propellant generator works by sublimating a solid crystal into vapor and then using this vapor to etch a dense metal. The resulting gaseous byproducts of this reaction are the propellant. This dissertation used xenon difluoride (XeF2) vapor to etch tungsten (W) which react to form xenon gas (Xe) and tungsten hexafluoride (WF6). This approach gave a theoretical propellant storage density 5.40 g/cm3; and 5.17 g/cm3 was demonstrated. The sublimation dynamics of the XeF2 were studied as a function of surface area and temperature and it was found to be suitable for the intended application due to its high effluence rate; that is, it sublimates fast enough to be useful. The sublimation rates are on the order of 10’s of µg/s. The etch rate of XeF2 on W was also studied and found to be suitably fast to provide useful amounts of reactants for use as a propellant, again on the order of 1’s of µg/s. The thruster is an electrostatic radio frequency (RF) ion thruster design and is manufactured with Low Temperature Co-Fired Ceramic (LTCC) materials system and manufacturing technology. Manufacturing samples of the thruster were built at the University of Arkansas in July 2015 and tested at NASA’s Marshall Space Flight Center in May 2018. Testing validated the viability of the LTCC thruster and provided valuable information on how to improve the thruster’s design.

Filament Winding Composite Airframes For Sounding Rockets, Eric Ford

Student Works

This study’s objective was to determine the feasibility of manufacturing carbon fiber cylinders using an X-Winder filament winder for a structural airframe in sounding rockets. Multiple carbon fiber tubes were manufactured using the X-Winder and tested. The results of this testing successfully demonstrated that tubes manufactured with the X-Winder are capable of performing as an airframe for small sounding rockets. Five tube samples were destructively tested in compression, and the average maximum compressive strength of the tubes was 9,854 lbf. One of the tubes was used as the airframe in a small sounding rocket which flew to 4,042 feet above …

Narmax Identification Based Closed-Loop Control Of Flow Separation Over Naca 0015 Airfoil, Sohaib Obeid, Goodarz Ahmadi, Ratneshwar Jha

Henry M. Rowan College of Engineering Departmental Research

A closed-loop control algorithm for the reduction of turbulent flow separation over NACA 0015 airfoil equipped with leading-edge synthetic jet actuators (SJAs) is presented. A system identification approach based on Nonlinear Auto-Regressive Moving Average with eXogenous inputs (NARMAX) technique was used to predict nonlinear dynamics of the fluid flow and for the design of the controller system. Numerical simulations based on URANS equations are performed at Reynolds number of 106 for various airfoil incidences with and without closed-loop control. The NARMAX model for flow over an airfoil is based on the static pressure data, and the synthetic jet actuator is …

Aerodynamic And Aeroacoustic Performance Of Small Uav Propellers In Static Conditions, William Jordan, Robert W. Deters, Shreyas Narsipur

Publications

The proliferation of small multi-rotor UAVs in commercial, recreational, and surveillance spheres has garnered significant interest in the noise produced by these vehicles. The current research aims to study the relationship between the aerodynamic performance and acoustic characteristics of small-scale UAV propellers. Three commercially available propellers for the DJI Phantom 2/3 UAV were selected for preliminary development and validation of an aeroacoustic experimental test setup and associated data reduction methods. Propeller thrust, torque, and power measurements were recorded at static conditions. Upon successful validation of the test bench, acoustic measurements were taken at the propeller disk’s upstream and in-plane locations. …

Performance Testing Of Aero-Naut Camfolding Propellers, Or D. Dantsker, Robert W. Deters, Marco Caccamo, Michael S. Selig

Publications

The increase in popularity of unmanned aerial vehicles (UAVs) has been driven by their use in civilian, education, government, and military applications. However, limited on-board energy storage significantly limits flight time and ultimately usability. The propulsion system plays a critical part in the overall energy consumption of the UAV; therefore, it is necessary to determine the most optimal combination of possible propulsion system components for a given mission profile, i.e. propellers, motors, and electronic speed controllers (ESC). Hundreds of options are available for the different components with little performance specifications available for most of them. By examining a variety of …

Numerical Method For Rapid Aerostructural Design And Optimization, Jeffrey D. Taylor, Douglas F. Hunsaker

Mechanical and Aerospace Engineering Student Publications and Presentations

During early phases of wing design, analytic and low-fidelity methods are often used to identify promising design concepts. In many cases, solutions obtained using these methods provide intuition about the design space that is not easily obtained using higher-fidelity methods. This is especially true for aerostructural design. However, many analytic and low-fidelity aerostructural solutions are limited in application to wings with specific planforms and weight distributions. Here, a numerical method for minimizing induced drag with structural constraints is presented that uses approximations that apply to wings with arbitrary planforms and weight distributions. The method is applied to the NASA Ikhana …

Vibration Isolation System, Bradley Y. Kwan, Bailey Groh, Max Wu, Nicole Yen

Mechanical Engineering

The Vibration Isolation System Senior Project is a collaborative group project between its sponsor, Maxar Technologies, and a team of students from Cal Poly - SLO to effectively design, manufacture, and test a structural assembly for satellites, isolating vibrations during launch and orbit conditions. After initial sponsor contact, requirements and needs were set which dictated deliverables for the senior project group. The group performed analyses to validate all design decisions, including a modified concept and design direction, selection of a prototype viscoelastic damping material, preliminary testing to validate design specifications, and detailed design and analysis toward a finalized design. Instead …

Impulse And Performance Measurements Of Electric Solid Propellant In A Laboratory Electrothermal Ablation-Fed Pulsed Plasma Thruster, Matthew S. Glascock, Joshua L. Rovey, Kurt A. Polzin

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Electric solid propellants are advanced solid chemical rocket propellants that can be controlled (ignited, throttled and extinguished) through the application and removal of an electric current. This behavior may enable the propellant to be used in multimode propulsion systems utilizing the ablative pulsed plasma thruster. The performance of an electric solid propellant operating in an electrothermal ablation-fed pulsed plasma thruster was investigated using an inverted pendulum micro-newton thrust stand. The impulse bit and specific impulse of the device using the electric solid propellant were measured for short-duration test runs of 100 pulses and longer-duration runs to end-of-life, at energy levels …

A Parametric Study Of Formation Flight Of A Wing Based On Prandtl's Bell-Shaped Lift Distribution, Kyle S. Lukacovic

Master's Theses

The bell-shaped lift distribution (BSLD) wing design methodology advanced by Ludwig Prandtl in 1932 was proposed as providing the minimum induced drag. This study used this method as the basis to analyze its characteristics in two wing formation flight. Of specific interest are the potential efficiency savings and the optimal positioning for formation flight. Additional comparison is made between BSLD wings and bird flight in formation.

This study utilized Computational Flow Dynamics (CFD) simulations on a geometric modeling of a BSLD wing, the Prandtl-D glider. The results were validated by modified equations published by Prandtl, by CFD modeling published by …

Initial Orbit Determination Error Analysis Of Low-Earth Orbit Rocket Body Debris And Feasibility Study For Debris Cataloguing From One Optical Facility, Kyle Stoker

Master's Theses

This paper is predicated on determining the effectiveness of angles-only initial orbit determination (IOD) methods when limited observational data is available for low-Earth orbit (LEO) rocket body debris. The analysis will be conducted with data obtained from Lockheed Martin Space’s Space Object Tracking (SpOT) facility, focusing on their observational data from 2018 that contains tracking of rocket body debris for less than one minute per overhead pass. After the IOD accuracies are better understood, a feasibility study will follow that investigates the possibility of cataloguing LEO orbital debris from a single optical observation facility with similar observational capabilities as that …

A Study Of The Design Of Adaptive Camber Winglets, Justin J. Rosescu

Master's Theses

A numerical study was conducted to determine the effect of changing the camber of a winglet on the efficiency of a wing in two distinct flight conditions. Camber was altered via a simple plain flap deflection in the winglet, which produced a constant camber change over the winglet span. Hinge points were located at 20%, 50% and 80% of the chord and the trailing edge was deflected between -5° and +5°. Analysis was performed using a combination of three-dimensional vortex lattice method and two-dimensional panel method to obtain aerodynamic forces for the entire wing, based on different winglet camber configurations. …

Pocket Rocket: A 1u+ Propulsion System Design To Enhance Cubesat Capabilities, James M. Harper

Master's Theses

The research presented provides an overview of a 1U+ form factor propulsion system design developed for the Cal Poly CubeSat Laboratory (CPCL). This design utilizes a Radiofrequency Electrothermal Thruster (RFET) called Pocket Rocket that can generate 9.30 m/s of delta-V with argon, and 20.2 ± 3 m/s of delta-V with xenon. Due to the demand for advanced mission capabilities in the CubeSat form factor, a need for micro-propulsion systems that can generate between 1 – 1500 m/s of delta-V are necessary.

By 2019, Pocket Rocket had been developed to a Technology Readiness Level (TRL) of 5 and ground tested in …

Application Of Mounting Personal Pid Voc Sensors To Small Unmanned Aircraft Systems To Aid First Responders, Cheri Marcham

Publications

Small Unmanned Aerial Systems in Emergency Response

• Current sUAS Uses
• Search and rescue
• Thermal imaging
• Evaluating structural stability
• Spread of wildfires
• Storm damage

Design And Test Of An Autonomy Monitoring Service To Detect Divergent Behaviors On Unmanned Aerial Systems, Loay Y. Almannaei

Theses and Dissertations

Operation of Unmanned Aerial Vehicles (UAV) support many critical missions in the United State Air Force (USAF). Monitoring abnormal behavior is one of many responsibilities of the operator during a mission. Some behaviors are hard to be detect by an operator, especially when flying one or more autonomous vehicles; as such, detections require a high level of attention and focus to flight parameters. In this research, a monitoring system and its algorithm are designed and tested for a target fixed-wing UAV. The Autonomy Monitoring Service (AMS) compares the real vehicle or simulated Vehicle with a similar simulated vehicle using Software …

Work-In-Progress: Augmented Reality System For Vehicle Health Diagnostics And Maintenance, Yuzhong Shen, Anthony W. Dean, Rafael Landaeta

Electrical & Computer Engineering Faculty Publications

This paper discusses undergraduate research to develop an augmented reality (AR) system for diagnostics and maintenance of the Joint Light Tactical Vehicle (JLTV) employed by U.S. Army and U.S. Marine Corps. The JLTV’s diagnostic information will be accessed by attaching a Bluetooth adaptor (Ford Reference Vehicle Interface) to JLTV’s On-board diagnostics (OBD) system. The proposed AR system will be developed for mobile devices (Android and iOS tablets and phones) and it communicates with the JLTV’s OBD via Bluetooth. The AR application will contain a simplistic user interface that reads diagnostic data from the JLTV, shows vehicle sensors, and allows users …

Development Of A State-Space Aeroelastic Model Of A Flexible T-Tail Aircraft For Flutter Analysis, Patrick S. Downs

Doctoral Dissertations and Master's Theses

Flutter prediction is an important part of the preliminary design process of any new aircraft. Current analysis methods include coupled fluid structure interaction codes and doublet lattice panel codes. The computation resources and time required for CFD solutions makes them unattractive for preliminary design and doublet lattice models require considerable pre and post processing to provide satisfactory results. Thus, a process for developing an analytical model to facilitate rapid design changes and the implementation of active control systems is the main motivation of this thesis. An analytical model is developed by first deriving the equations of motion of the structure …