Engineering Commons^™

Covariance Analysis For Multi-Source Navigation Architecture, Tristan T. Williams

Theses and Dissertations

Currently, analysis on navigation systems can be slow and computationally expensive using Monte Carlo approaches. Covariance analysis is a tool that can return trade space analysis results promptly and can be computationally reasonable. This research aims to create a covariance analysis tool in a new navigation framework architecture, PntOS. The creation of this covariance tool is explained in coordination with the tool being used in a few different navigation scenarios with the results. These scenarios include a Doppler LiDAR velocity sensor and magnetic anomaly navigation.

Magnetic Navigation Using Online Calibration Filter Analysis, Jonnathan D. Bonifaz

Theses and Dissertations

Magnetic navigation using the Earth’s magnetic anomaly field has proven to be a promising alternative that can provide coverage for a navigation system. This research demonstrates a magnetic navigation system using an extended Kalman filter (EKF) to aid an aircraft’s inertial navigation system (INS). Traditional magnetic anomaly navigation uses a “static calibration method,” which takes post-processed data to calibrate, obtaining the Tolles-Lawson coefficients needed for magnetic anomaly navigation filter compensation. These coefficients are constant and may cause drifts in the navigation filter if not re-calibrated. The online calibration method continuously updates the Tolles-Lawson coefficients as a filter state, reducing the …

Satellite Tt&C For Cubesats With Applications For Grissom-1, Michael J. Bittle

Theses and Dissertations

This thesis describes the assessment and analysis performed to characterize the communication subsystem used for command and telemetry transmission in support of the Grissom-1 Mission (GM1). The GM1 is unique in that it represents the pathfinder for a standardized 6U bus that serves as the basis for future CubeSat missions to host a variety of technical and scientific payloads, as prioritized by the Department of Defense, requiring flight demonstration or access to the orbital environment. Lab-based testing within an anechoic chamber provided link margin data required to characterize the command and telemetry links of the GM1. Experimental data describing the …

Design And Testing Of A Composite Compressor Rotor, Mauro Noel V. De Leon

Theses and Dissertations

Additive manufacturing (AM) and molding are manufacturing methods known for building representations or replicas of conceptualized engine components, but was considered impractical for manufacturing operating engine components. More recent technology has rendered composite materials (combining high-temperature polymers and fiber reinforcement) capable of withstanding the temperature and structural requirements to compete with conventional turbomachinery metals. This study explores the application of several high-temperature polymers (ULTEM 9085, Onyx-Carbon fiber, and Epoxy-Carbon fiber) and their survivability in the operating conditions of a P400 Engine compressor. The tests conducted for this study determined their viability as compressor materials. This study required conducting tensile specimen …

Leveraging Xgeo Orbits For Cislunar Space Domain Awareness, Jay Laone

Theses and Dissertations

With recent interest in using cislunar orbits for a variety of missions, it is more important than ever to also have cislunar space domain awareness. This thesis aims to bridge the gap between traditional LEO/GEO architectures and the new cislunar orbit architectures with orbits higher than GEO but still within the Earth sphere of influence, called xGEO. This research effort first explores the feasibility of xGEO orbits by examining the errors that the two-body assumption builds over time. Findings suggest that the two body assumption can be used to varying degrees depending on the orbit radius. This study has found …

Investigation Of Additively Manufactured Molybdenum-Tungsten-Rhenium Alloys, Randolph T. Abaya

Theses and Dissertations

The process of creating metal components through additive manufacturing is changing the way different industries can avoid the shortcomings of traditional metal production. Metals such as tungsten, molybdenum, and rhenium have many advantages for different applications, especially when alloyed together. In this study, an additively manufactured alloy containing 70% molybdenum, 25% tungsten, and 5% rhenium (70Mo-25W-5Re) is tested for its strength, ductility, hardness, and porosity. The 70Mo-25W-5Re alloy is printed through Laser Powder Bed Fusion (LPBF) under different conditions such as printing speed and printing atmosphere. Additionally, the effects of post printing heat treatment are conducted to understand the advantages …

Effects Of A Nitrogen And Hydrogen Build Atmosphere On The Properties Of Additively Manufactured Tungsten, Dana C. Madsen

Theses and Dissertations

Additively manufactured tungsten was printed in pure nitrogen, nitrogen-2.5% hydrogen, and nitrogen-5% hydrogen atmospheres as part of a 2^3 full factorial designed experiment and subjected to room temperature and high-temperature three-point-bend testing, chemical analysis, hardness testing, and microstructural imaging techniques. The pure nitrogen specimens exhibited the highest strength and ductility at both high temperature and room temperature. Chemical analysis showed a 2-8x reduction in compositional oxygen relative to unprocessed powder. Hardness values for all samples was between 306.8 and 361.5 HV1. It is proposed that adding hydrogen into the build atmosphere reduced the available energy density for tungsten melting by …

Thermal Relaxation Of Shot Peen Induced Residual Stresses In A Nickel-Base Superalloy, Bryce E. Van Velson

Theses and Dissertations

Shot peening induces compressive residual stresses in components that positively influence fatigue life. Thermal and mechanical loading causes those residual stresses to relax. The hole drilling method and xray diffraction is used to measure the thermal relaxation of residual stresses in the nickel-base superalloy ME3.

Double Cone Flow Field Reconstruction Between Mach 4 And 12 Using Machine Learning Techniques, Trevor A. Toros

Theses and Dissertations

No abstract provided.

Experimental Study Of Turbulent Flow Heat Transfer And Pressure Loss Over Surfaces With Dense Micro-Depth Dimples Under Viscous Sublayer, Peng Zhang, Yu Rao, Phillip M. Ligrani

PRC-Affiliated Research

Presented are experimentally-measured heat transfer and pressure loss characteristics for dimpled surfaces, placed along one surface of a channel, with different ratios of dimple depth to channel height δ/H, and for Reynolds numbers ranging from 10,000 to 70,000. With the same relative dimple spacing to dimple print diameter, and the same ratio of dimple depth to dimple print diameter of δ/d = 0.20, experimental results for arrays of spherical indentation dimples with micro depths of δ = 0.6 and 1.0 mm (δ/H = 0.03 and 0.05) are compared with thermal characteristics for arrays of larger dimples with δ = 4.0 …

Effect Of Processing Parameters And Build Orientation On Microstructure And Performance Of Aisi Stainless Steel 304l Made With Selective Laser Melting Under Different Strain Rates, Tan Pan, Xinchang Zhang, Aaron Flood, Sreekar Karnati, Wei Li, Joseph William Newkirk, Frank W. Liou

Materials Science and Engineering Faculty Research & Creative Works

Selective laser melting (SLM) process allows greater geometry flexibility; therefore, it has become more widespread in its deployment in the industry for fabricating metal alloys. However, a material characterization study is needed in order to understand better the correlation between the process, microstructure, and performance. In the current study, the raw SLM fabricated AISI stainless steel 304 L was fabricated with different processing parameters and build orientations (horizontal, inclined, and vertical). The tensile behavior was evaluated under different strain rates (0.0001/s, 0.001/s, 0.01/s, and 0.1/s) and then compared to commercial cold-rolled and annealed counterparts. Grain structures, tensile strength, elongation-to-failure, strain …

Six-Bar Linkage Models Of A Recumbent Tricycle Mechanism To Increase Power Throughput In Fes Cycling, Nicholas A. Lanese, David H. Myszka, Anthony L. Bazler, Andrew P. Murray

Mechanical and Aerospace Engineering Faculty Publications

This paper presents the kinematic and static analysis of two mechanisms to improve power throughput for persons with tetra- or paraplegia pedaling a performance tricycle via FES. FES, or functional electrical stimulation, activates muscles by passing small electrical currents through the muscle creating a contraction. The use of FES can build muscle in patients, relieve soreness, and promote cardiovascular health. Compared to an able-bodied rider, a cyclist stimulated via FES produces an order of magnitude less power creating some notable pedaling difficulties especially pertaining to inactive zones. An inactive zone occurs when the leg position is unable to produce enough …

Developing Metrics For Nasa Earth Science Interdisciplinary Data Products And Services, Zhong Liu, Chung-Lin Shie, Anthony J. Ritrivi, Guang-Dih Lei, Gary T. Alcott, Mary Greene, James Acker, Jennifer C. Wei, David J. Meyer, Angela Li, Atheer F. Al-Jazrawi

Copyright, Fair Use, Scholarly Communication, etc.

Metrics are measures that are able to produce quantifiable information. There are many applications of metrics in Earth science data and services; for example, metrics are frequently used to track service performance and progress. In short, developing, collecting and analyzing metrics are essential activities to better support Earth science research, applications, and education.

As one of the largest repositories of Earth science data in the world, NASA’s Earth Science Data and Information System (ESDIS) Project supports twelve Distributed Active Archive Centers (DAACs). Standard metrics have been developed by the ESDIS Metrics System (EMS). These metrics are collected and analyzed routinely …

Effects Of Particle Size Distribution With Efficient Packing On Powder Flowability And Selective Laser Melting Process, Zachary Young, Minglei Qu, Meelap Michael Coday, Qilin Guo, Seyed Mohammad H. Hojjatzadeh, Luis I. Escano, Kamel Fezzaa, Lianyi Chen

Mechanical and Aerospace Engineering Faculty Research & Creative Works

The powder bed-based additive manufacturing (AM) process contains uncertainties in the powder spreading process and powder bed quality, leading to problems in repeatability and quality of the additively manufactured parts. This work focuses on identifying the uncertainty induced by particle size distribution (PSD) on powder flowability and the laser melting process, using Ti6Al4V as a model material. The flowability test results show that the effect of PSDs on flowability is not linear, rather the PSDs near dense packing ratios cause significant reductions in flowability (indicated by the increase in the avalanche angle and break energy of the powders measured by …

Data On The Validation To Determine The Material Thermal Properties Estimation Via A One-Dimensional Transient Convection Model, Lauren B. Tomanek, Daniel S. Stutts

Mechanical and Aerospace Engineering Faculty Research & Creative Works

These data were acquired to estimate the parameters of a closed form solution of a one-dimensional transient convection heat diffusion PDE. The purpose was to demonstrate that the model could be used to determine the thermal conductivity. The system was tested for a wide range of thermal conductivity, 15-400 W/mK, in order to verify that the method was applicable for various materials. The data reported here refer to the study in the research articles, "Material Thermal Properties Estimation Via a One-Dimensional Transient Convection Model" [1] and "Influence of porosity on the thermal, electrical, and mechanical performance of selective laser melted …

Flow And Heat Transfer Characteristics In A Pre-Swirl Rotor-Stator Cavity, Xiaoyu Yang, Zhong Ren, Jing Ren, Philip M. Ligrani

PRC-Affiliated Research

The present study investigates flow and heat transfer characteristics in a rotor-stator pre-swirl system. Considered are rotational Reynolds numbers ReФ ranging from 3.4 × 105 to 6.8 × 105, with jet Reynolds numbers Rew of approximately 8.8 × 104 to 3.81 × 105, and associated turbulent flow parameter λT = Cw/ReФ0.8 varying from 0 to 0.4. Experimentally-measured and numerically-predicted results illustrate the combined and separate influences of jet impingement and rotor entrainment, as they affect and govern flow and heat transfer characteristics within the cavity. These results show that the relative strength of the two effects varies with ReФ and …

Flow Structure And Surface Heat Transfer From Numerical Predictions For A Double Wall Effusion Plate With Impingement Jet Array Cooling, Hwabhin Kwon, Phillip M. Ligrani, Sneha Reddy Vanga, Heesung Park

PRC-Affiliated Research

To provide additional understanding of double wall cooling arrangements, especially local distributions of flow properties which are responsible for hot-side surface and cold-side surface heat transfer variations, investigated are numerically-simulated distributions of turbulent flow structural characteristics. Also considered are numerically-simulated surface heat transfer characteristics, including comparisons with experimentally-measured distributions. The numerical results are obtained using the ANSYS FLUENT Version 19.1 numerical code, with a k-ω SST turbulence model. The present arrangement includes a full-coverage effusion cooling plate, with coolant initially supplied by an impingement jet array. Considered are the effects of effusion blowing ratio, impingement jet Reynolds number, and streamwise …

Characterization, Design, And Optimization Of Dual-Purpose Wind Turbines And Frost Protection Fans, Ethan Narad

Master's Theses

This thesis report outlines the creation of a MATLAB tool to design reversible machines that can function as both wind turbines and as agricultural frost protection fans. Frost protection fans are used to prevent crop loss during radiative freeze events during which a temperature inversion is present. Such a dual-purpose machine fundamentally has the constraint that it must use symmetric airfoils, so a suite of tools for automatically designing an optimized wind turbine blade with symmetric airfoils using the Blade Element Momentum (BEM) theory approach is presented. The BEM code is then re-derived and adapted for use with a frost …

Robust Error Estimation Based On Factor-Graph Models For Non-Line-Of-Sight Localization, O. Arda Vanli, Clark N. Taylor

Faculty Publications

This paper presents a method to estimate the covariances of the inputs in a factor-graph formulation for localization under non-line-of-sight conditions. A general solution based on covariance estimation and M-estimators in linear regression problems, is presented that is shown to give unbiased estimators of multiple variances and are robust against outliers. An iteratively re-weighted least squares algorithm is proposed to jointly compute the proposed variance estimators and the state estimates for the nonlinear factor graph optimization. The efficacy of the method is illustrated in a simulation study using a robot localization problem under various process and measurement models and measurement …

Eye-Gaze-Controlled Hmds And Mfd For Military Aircraft, Lrd Murthy, Abhishek Mukhopadhyay, Somnath Arjun, Varshith Yelleti, Peter Thomas, Dilli Babu Mohan, Pradipta Biswas

Journal of Aviation Technology and Engineering

Eye-gaze-controlled interfaces allow the direct manipulation of a graphical user interface by looking at it. This technology has great potential in military aviation, in particular, operating different displays in situations where pilots’ hands are occupied with flying the aircraft. This paper reports studies on analyzing the accuracy of eye-gaze-controlled interfaces inside aircraft undertaking representative flying missions. We report that using eye-gaze-controlled interfaces, pilots can undertake representative pointing and selection tasks at less than two seconds on average in a transport aircraft. Further, we analyzed the accuracy of eye-gaze-tracking glasses under various G load factors and analyzed the failure modes. We …

Characterization Of Effective Diffusion Within Viscoelastic Fluids With Elastic Instabilities, Valerie Hietsch, Phillip Ligrani, Mengying Su

PRC-Affiliated Research

We considered effective diffusion, characterized by magnitudes of effective diffusion coefficients, in order to quantify mass transport due to the onset and development of elastic instabilities. Effective diffusion coefficient magnitudes were determined using different analytic approaches, as they were applied to tracked visualizations of fluorescein dye front variations, as circumferential advection was imposed upon a flow environment produced using a rotating Couette flow arrangement. Effective diffusion coefficient results were provided for a range of flow shear rates, which were produced using different Couette flow rotation speeds and two different flow environment fluid depths. To visualize the flow behavior within the …

The Chime Fast Radio Burst Population Does Not Track The Star Formation History Of The Universe, Rachel C. Zhang, Bing Zhang

Physics & Astronomy Faculty Research

The redshift distribution of fast radio bursts (FRBs) is not well constrained. The association of the Galactic FRB 200428 with the young magnetar SGR 1935+2154 raises the working hypothesis that FRB sources track the star formation history of the universe. The discovery of FRB 20200120E in association with a globular cluster in the nearby galaxy M81, however, casts doubts on such an assumption. We apply the Monte Carlo method developed in a previous work to test different FRB redshift distribution models against the recently released first CHIME FRB catalog in terms of their distributions in specific fluence, external dispersion measure …

Pro Tips For Cfis: The Secret Life Of Stalls, Nihad E. Daidzic

Aviation Department Publications

FAA Safety webinar (GL1590721) held online at 7:00 CST on Wednesday, January 5, 2022.

Social Representations Of Space Travel, Asli D. A. Tasci, Alan Fyall, Xiaoxiao Fu

Rosen Research Review

Space tourism regularly receives media coverage, but so far, there has been little research around public opinions towards space travel. Dr. Asli D.A. Tasci, Dr. Alan Fyall and Dr. Xiaoxiao Fu from UCF Rosen College of Hospitality Management used the Social Representations Theory to investigate public attitudes to space travel and uncover how and why these attitudes are formed. They discovered that commercial space organizations have a strong influence on public opinion, which can be further enhanced if they incorporate more scientific knowledge and evidence.

A Qualitative Single-Case Exploring The Impact Of A Mentor And Cohort On Students’ Academic And Career Decisions., Kevin Adkins, Samantha Bowyer, Jorge L. D. Albelo Ph.D.

Publications

Exposure to research is known to play a positive role in undergraduate education. However, robust research responsibilities are oftentimes not formally incorporated into a student’s academic experience until master level studies. Further, a variety of intimidation factors often inhibit many undergraduate students from participating on a research team. In this case study, the research team evaluated a unique group of undergraduate researchers who matriculated to the same university after beginning to participate in research as concurrently enrolled students. Following matriculation, each student continued to participate in research throughout the entirety of their undergraduate studies. All of the study’s students were …

Carbon Fiber Recycling: Delamination System, Aaron Eastman

All Undergraduate Projects

The production of composite wings at Boeing causes carbon fiber waste and CWU Mechanical Engineering Technology students have been tasked in designing a carbon fiber recycling system. This project was brought forth and funded by the Joint Center for Aerospace Technology Innovation (JCATI). There are three subsystems that make up the carbon fiber recycling system, the delamination system, shredding system, and the oven. The purpose of this project was to increase the efficiency and effectiveness of the delamination system of the carbon fiber recycling system. The old system reached approximately 30-40 percent delamination with one pass through the system, and …

Jcati Carbon Fiber Shredder 2022, Parker Sudderth

All Undergraduate Projects

This project is a potential solution to keep the carbon fiber waste from airplane manufacturing to a minimum, sponsored by the Joint Center for Aerospace Technology Innovation (JCATI). The design and assembly will be scalable for future industry application. The overall design of the whole carbon fiber recycler consists of a crusher, shredder, and oven. This report is on the caron fiber shredder module. The shredder is tasked with being able to shred the delaminated carbon fiber scrap that directly comes from the crusher. The operation must produce shreds in the proper size to be gathered and delivered to the …

Uas Obstacle Database For University Traffic Management System, Casey Calamaio

Summer Community of Scholars (RCEU and HCR) Project Proposals

No abstract provided.

Design And Development Of Active Flow Effectors, Konstantinos Kanistras

Summer Community of Scholars (RCEU and HCR) Project Proposals

No abstract provided.

Design And Development Of An Online Wind Tunnel, Konstantinos Kanistras

Summer Community of Scholars (RCEU and HCR) Project Proposals

No abstract provided.