Engineering Commons^™

Spin Recovery Analysis On A Simulation Model Of The Nasa F-18 High Alpha Research Vehicle (Harv) Using Thrust Vectoring, Brock M. Dolly

Graduate Theses, Dissertations, and Problem Reports (ETD)

In the early years of aviation, spins were poorly understood and frequently fatal. With just over a century of research and experiments dedicated to spins, today’s aviation world has a very firm grasp on spin aerodynamics. Most fighter aircraft have airframes and control surfaces specifically designed to ensure the ability of departure from the possible spin modes the aircraft can enter. An alternative and/or additional approach is given by thrust vectoring. Implementing thrust vectoring into spin recovery can potentially save an aircraft and/or the life of the pilot in situation where control-surface-only spin recovery is not able to recover the …

Optimal Deployment Of Air Vehicle As Communication Relay For Multiple Ground Vehicles, Juan David Pabon Arias

Graduate Theses, Dissertations, and Problem Reports (ETD)

Heterogeneous teams of both air and ground mobile vehicles can combine the advantages of mobility, sensing capability, and operation time when performing complex tasks. However, when ground vehicles operate in cluttered environments with randomized obstacles, they may experience line of sight (LoS) obstructions and loss of communication due to those obstacles. To mitigate this issue, an airborne relay can be positioned in the vicinity of the ground vehicles to aid communication by establishing two-hop communication links between the vehicles.

This thesis develops an analytical framework to calculate the probability of spanning a two-hop communication between a pair of ground vehicles …

Motion Planning In Artificial And Natural Vector Fields, Bernardo Martinez Rocamora Junior

Graduate Theses, Dissertations, and Problem Reports (ETD)

This dissertation advances the field of autonomous vehicle motion planning in various challenging environments, ranging from flows and planetary atmospheres to cluttered real-world scenarios. By addressing the challenge of navigating environmental flows, this work introduces the Flow-Aware Fast Marching Tree algorithm (FlowFMT*). This algorithm optimizes motion planning for unmanned vehicles, such as UAVs and AUVs, navigating in tridimensional static flows. By considering reachability constraints caused by vehicle and flow dynamics, flow-aware neighborhood sets are found and used to reduce the number of calls to the cost function. The method computes feasible and optimal trajectories from start to goal in challenging …

Probabilistic Short Term Solar Driver Forecasting With Neural Network Ensembles, Joshua Daniell

Graduate Theses, Dissertations, and Problem Reports (ETD)

Commonly utilized space weather indices and proxies drive predictive models for thermosphere density, directly impacting objects in low-Earth orbit (LEO) by influencing atmospheric drag forces. A set of solar proxies and indices (drivers), F_10.7, S_10.7, M_10.7, and Y_10.7, are created from a mixture of ground based radio observations and satellite instrument data. These solar drivers represent heating in various levels of the thermosphere and are used as inputs by the JB2008 empirical thermosphere density model. The United States Air Force (USAF) operational High Accuracy Satellite Drag Model (HASDM) relies on JB2008, and …

Computational And Experimental Investigation Of Mass Reduced Aircraft Wing Ribs, Charles R. Fricks Iii

College of Graduate Studies: Theses & Dissertations

This study seeks to develop and evaluate a novel design of mass reduced aircraft wing ribs through the topology optimization method. For comparison, the same examination is performed on ribs with normal internal geometry. The wing rib design is based on that of the Gulfstream G650 transonic jet. The rib was divided into three segments for analysis based around the positions of the two spars. Only the center section of the rib (that being between the forward and aft spars) is mass optimized, while the leading and trailing edges of the ribs (outside the spars) will be kept solid for …

Strategies Aircraft Manufacturing Organizational Leaders Use For Proper Material Pricing, Chin Kuei Jen

Walden Dissertations and Doctoral Studies

The lack of proper material pricing strategies can challenge manufacturers’ profitability and growth. Aircraft manufacturing leaders are concerned because understanding and developing material pricing strategies are essential to increasing profitability. Grounded in price theory, the purpose of this qualitative single case study was to explore strategies aircraft manufacturing organizational leaders use for proper material pricing estimates. The participants were four aircraft manufacturing organizational leaders from a successful aircraft manufacturing business located in the state of Georgia. Data were gathered from semistructured interviews and document reviews and analyzed using Yin’s five step approach. The four themes that emerged were the impact …

Underwater Communication Acoustic Transducers: A Technology Review, Laila Shams, Tian-Bing Xu, Zhongqing Su (Ed.), Branko Glisic (Ed.), Maria Pina Limongelli (Ed.)

Mechanical & Aerospace Engineering Faculty Publications

This paper provides a comprehensive review on transducer technologies for underwater communications. The popularly used communication transducers, such as piezoelectric acoustic transducers, electromagnetic acoustic transducers, and acousto-optic devices are reviewed in detail. The reasons that common air communication technologies are invalid die to the differences between the media of air and water are addresses. Because of the abilities to overcome challenges the complexity of marine environments, piezoelectric acoustic transducers are playing the major underwater communication roles for science, surveillance, and Naval missions. The configuration and material properties of piezoelectric transducers effects on signal output power, beamwidth, amplitude, and other properties …

Numerical Study Of The Time-Periodic Electroosmotic Flow Of Viscoelastic Fluid Through A Short Constriction Microchannel, Jianyu Ji, Shizhi Qian, Armani Marie Parker, Xiaoyu Zhang

Mechanical & Aerospace Engineering Faculty Publications

Electroosmotic flow (EOF) is of utmost significance due to its numerous practical uses in controlling flow at micro/nanoscales. In the present study, the time-periodic EOF of a viscoelastic fluid is statistically analyzed using a short 10:1 constriction microfluidic channel joining two reservoirs on either side. The flow is modeled using the Oldroyd-B (OB) model and the Poisson-Boltzmann model. The EOF of a highly concentrated polyacrylamide (PAA) aqueous solution is investigated under the combined effects of an alternating current (AC) electric field and a direct current (DC) electric field. Power-law degradation is visible in the energy spectra of the velocity fluctuations …

Artificial Intelligence-Enabled Exploratory Cyber-Physical Safety Analyzer Framework For Civilian Urban Air Mobility, Md. Shirajum Munir, Sumit Howlader Dipro, Kamrul Hasan, Tariqul Islam, Sachin Shetty

VMASC Publications

Urban air mobility (UAM) has become a potential candidate for civilization for serving smart citizens, such as through delivery, surveillance, and air taxis. However, safety concerns have grown since commercial UAM uses a publicly available communication infrastructure that enhances the risk of jamming and spoofing attacks to steal or crash crafts in UAM. To protect commercial UAM from cyberattacks and theft, this work proposes an artificial intelligence (AI)-enabled exploratory cyber-physical safety analyzer framework. The proposed framework devises supervised learning-based AI schemes such as decision tree, random forests, logistic regression, K-nearest neighbors (KNN), and long short-term memory (LSTM) for predicting and …

Jet Noise Reduction: A Fresh Start, Christopher K. Tam, Fang Q. Hu

Mathematics & Statistics Faculty Publications

Attempts to reduce jet noise began some 70 years ago. In the literature, there have been many publications written on this topic. By now, it is common knowledge that jet noise consists of a number of components. They possess different spectral and radiation characteristics and are generated by different mechanisms. It appears then that one may aim at the suppression of the noise of a single component instead of trying to reduce jet noise overall. The objective of the present project is to reduce large turbulence structures noise. It is the most dominant noise component radiating in the downstream direction. …

Microstructure And Residual Stress In Functionally Graded 316l Stainless Steel/Inconel 625 Alloys Fabricated By Direct Energy Deposition, Xinchang Zhang, Liang Wang, Frank W. Liou, Yang Ren, Cheng Sun

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Functionally graded materials (FGMs) provide a unique solution to combine distinct properties within a single component to enhance its overall performance. Understanding the microstructure and residual stress distribution is particularly important as the material dissimilarity in FGMs can result in high residual stress that affects the mechanical integrity of structural components. This work aims to study the microstructure and residual stress of additively manufactured FGMs and the effects of isothermal annealing. In this study, 316L stainless steel/Inconel 625 FGMs were built by direct energy deposition and characterized by optical and electron microscopy as well as synchrotron-based X-ray diffraction. Our study …

Charging Of Irregularly-Shaped Dust Grains Near Surfaces In Space, David Lund, Xiaoming He, Daoru Han

Mathematics and Statistics Faculty Research & Creative Works

This paper presents fully kinetic numerical investigation of the charging of dust grains in low temperature collision less plasmas (stationary) and collision less, cold-ion thermal-electron drifting plasmas. the Parallel Immersed-Finite-Element Particle-in-Cell (PIFE-PIC) code is utilized to self-consistently resolve the plasma environment and charging of immersed materials. This model explicitly includes the materials property (dielectric constant) of dust grains. Effects of materials property, inter-dust distance, and plasma conditions (stationery and drifting) will be investigated for both single-dust and multi-dust configurations.

Nanobubble-Induced Aggregation Of Ultrafine Particles: A Molecular Dynamics Study, Eric Bird, Zhi Liang

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Nanobubble-induced aggregation (NBIA) of fine and ultrafine particles in liquid is a promising method for enhancing floatation rates in mineral processing, cleaning contaminants from water, and reviving marine ecosystems. Although the current experimental techniques can measure the nanobubble capillary force between two surfaces with controlled approach speed, they are not capable of imaging NBIA dynamics of fine/ultrafine particles by real-time observation with nanoscale spatial resolution. In this work, we use molecular dynamics (MD) simulations to study dynamics of NBIA of Ag particles in a Lennard-Jones fluid system. The molecular-level modeling allows us to study microscopic details of NBIA dynamics that …

Microstructure, Mechanical Properties And Oxidation Behavior Of Refractory Multi-Principal Element Alloys By Laser Remelting And Conventional Manufacturing, Visharad Jalan, Seth Crawford, Sung Heng Wu, Frank W. Liou, Haiming Wen

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Refractory Multi-Principal Element Alloys (RMPEAs), HfNbTaTiZr, (HfNbTaTiZr)₉Cr, and (HfNbTaTiZr)₉Al, Were Manufactured using Vacuum Arc Melting Followed by Laser Remelting to Mimic Additive Manufacturing. the Microhardness of the As-Cast HfNbTaTiZr, (HfNbTaTiZr)₉Cr, and (HfNbTaTiZr)₉Al Samples after Arc Melting Was Measured as 6.20, 7.63, and 6.89 Gpa, respectively. after Laser Remelting and Re-Solidification, the Hardness Increased by ~ 30% for Each Composition; the Hardest Was (HfNbTaTiZr)₉Cr Measured at 9.60 GPa, While the Softest Was HfNbTaTiZr with a Hardness of 8.42 GPa, Which Was Still Harder Compared to All the Other Samples. the Addition …

Development Of A Regeneratively Cooled Liquid Rocket Engine, Dillon Petty, Nicole Zimmerli

Williams Honors College, Honors Research Projects

An additively manufactured (AM) liquid rocket engine, consisting of an injector, combustion chamber, and nozzle, was designed and printed using state-of-the-art methods and materials. The parts were manufactured using laser powder bed fusion. Additive manufacturing allowed for complex geometries and features, such as printing manifolds onto the components with a reduced number of parts. Additive, regenerative cooling channels were designed into the chamber and nozzle to allow for long-duration steady-state operation.

The feed system for the engine was designed and built to allow for pressure-regulated and steady-state testing. Tanks for the fuel and oxidizer were designed and built for a …

Quadcopter Airfoil Analyses, Isabella Allen, Nicholas Tolson, Trevor Mccaffrey

Williams Honors College, Honors Research Projects

This project focuses on the aerodynamic analysis of airfoils for quadcopter applications, aiming to optimize the performance of quadcopters through the selection and analysis of various 3D printed airfoil profiles. Quadcopters are unmanned aerial vehicles with four rotors arranged in a symmetric configuration. Each diagonal pair rotates in the same direction, allowing the offset to ensure the quadcopter remains level. The airfoil selection is crucial as it impacts aerodynamic performance, stability, and efficiency. The parameter of interest in these airfoils is maximum thrust and settling thrust produced, along with material wear of the propellers themselves. The testing of thrust production …

Implementing Systems Engineering Practices To The Zips Aero Design Team, Kaitlyn Bebb, Ariel Bryan

Williams Honors College, Honors Research Projects

The Zips Aero Design Team is a college sponsored design team that competes each year through the American Institute of Aeronautics and Astronautics (AIAA) Design Build Fly (DBF) competition. The rules generally consist of 3 differing flight missions and a ground mission, with overarching requirements such as size, takeoff distance, and battery limitations. A complex set of rules such as these is meant to be difficult for even the best of teams to master, especially without proper organization and project management. This senior design report outlines the benefits of implementing systems engineering to the Zips Aero Design Team, through multiple …

Surface Preparation Study, Ryan Ferguson

Williams Honors College, Honors Research Projects

This work explores a custom air atmospheric pressure plasma treatment (APPT) machine’s effectiveness in cleaning and chemically activating a CFRP surface. It is explore by implementing water contact angle (WCA) measurements, water-break free (WBF) testing, and adhesive tubular lap-joint (TLJ) tensile testing. An 8x3 test matrix of different machine parameters is defined with the bounding conditions being the machine’s capabilities and industry standard recommendations. Each configuration of the test matrix is explored after treatment at multiple time intervals up to 2 weeks afterwards to gain insight into the outlife of the treatments with the intention of adhesively bonding to the …

Evaluating System Usability, Workload Suitability, And User Experience Of Game-Based Virtual Reality In Spaceflight Education And Training, Lana Laskey, Joseph R. Keebler

Journal of Aviation/Aerospace Education & Research

Game-based instruction and immersive virtual reality are enhanced pedagogical methods beneficial in training environments involving complex disciplines, ranging from medical applications to construction engineering technology. This study investigated the use of game-based virtual reality (GBVR) when applied to the complex field of spaceflight education and training. As modern society places increasing demand on space-based amenities, the need for proficient satellite operators will also increase, requiring more accessible and advanced training options. Satellite ground control training scenarios, immersed in the GBVR environment, were developed and deployed to university student participants. Multiple validated scales were employed to measure the GBVR system regarding …

Landing Gear Sealing Solution, Andrew Milligan

Williams Honors College, Honors Research Projects

XYZ Landing Gear Solutions has been tasked with redesigning two internal components of the landing gears for the ABC-123 aircraft program. The customer, ABC Aeronautics, informed XYZ Landing Gear Solutions that a particular system of the landing gear does not meet the necessary performance requirements of the program. As a result, the entire system will have to be removed, facilitating the need for a redesign of the two components that the system interfaced with. The focus of this project will be completing the redesign process for both of these components. “Redesign” and “design” will be used interchangeably in this report. …

Media Streaming In A High-Rate Delay Tolerant Network, Kyle Vernyi

Williams Honors College, Honors Research Projects

Audio and video streaming across delay tolerant networks are relatively new phenomena. During the Apollo 11 mission, video and audio were streamed directly back to Earth using fully analog radios. This streaming capability atrophied over time. The gradual conversion to digital electronics contributed greatly to this. Additionally, 21st century space systems face the new requirement of interconnectedness. Delay Tolerant Networking (DTN) attempts to solve this requirement by uniting traditional point to point links into a robust and dynamic network. However, DTN implementations present bottlenecks due to low performance. High-Rate Delay Tolerant Networking (HDTN) is a performance-optimized DTN implementation. This work …

Induced Drag Laboratory Curriculum With Variable Aspect Ratio Wing, Alexander Milligan, Elizabeth Plyler

Williams Honors College, Honors Research Projects

A laboratory curriculum for undergraduate students at The University of Akron enrolled in 4600:413 Introduction to Aerodynamics was created to allow students a hands-on opportunity to study the basic fundamentals of aerodynamically induced drag. To accomplish this, a 3D printed wing was created with variable aspect ratio. This wing is to be utilized in the laboratory experiment in The University of Akron subsonic wind tunnel to generate data on lift on drag at different airspeeds, angles of attack, and aspect ratios. The laboratory curriculum provides basic theory applicable to the wind tunnel experiments as well as question prompts and data …

Space Force Design Project, Emily Greene, Ashton Orosa, Julia Patek, Nathan Doty

Williams Honors College, Honors Research Projects

The objective of our research project is to develop a lab testbed composed of a curved surface to represent a spacecraft hull, a mobile robot equipped with repair tools, and a robotic arm equipped with a laser 3D scanner. This project is part of a larger grant to the University of Akron from Space Force and Air Research Labs. The lab testbed developed in this project will be used to assist in creating and testing a software and algorithm to inspect and repair spacecraft while in orbit. The project will involve researching spacecraft hulls to create an accurate simulation bed, …

Strategies Aircraft Manufacturing Organizational Leaders Use For Proper Material Pricing, Chin Kuei Jen

Walden Dissertations and Doctoral Studies

The lack of proper material pricing strategies can challenge manufacturers’ profitability and growth. Aircraft manufacturing leaders are concerned because understanding and developing material pricing strategies are essential to increasing profitability. Grounded in price theory, the purpose of this qualitative single case study was to explore strategies aircraft manufacturing organizational leaders use for proper material pricing estimates. The participants were four aircraft manufacturing organizational leaders from a successful aircraft manufacturing business located in the state of Georgia. Data were gathered from semistructured interviews and document reviews and analyzed using Yin’s five step approach. The four themes that emerged were the impact …

Application Of Multi-Scale Computational Techniques To Complex Materials Systems, Mujan N. Seif

Theses and Dissertations--Chemical and Materials Engineering

The applications of computational materials science are ever-increasing, connecting fields far beyond traditional subfields in materials science. This dissertation demonstrates the broad scope of multi-scale computational techniques by investigating multiple unrelated complex material systems, namely scandate thermionic cathodes and the metallic foam component of micrometeoroid and orbital debris (MMOD) shielding. Sc-containing "scandate" cathodes have been widely reported to exhibit superior properties compared to previous thermionic cathodes; however, knowledge of their precise operating mechanism remains elusive. Here, quantum mechanical calculations were utilized to map the phase space of stable, highly-faceted and chemically-complex W nanoparticles, accounting for both finite temperature and chemical …

Optimal Spacecraft Guidance, Matthew W. Harris, M. Benjamin Rose

Mechanical and Aerospace Engineering Faculty Publications

This book is designed for a one-semester course at Utah State University titled MAE 6570 Optimal Spacecraft Guidance. The class meets for 75 minutes, twice per week, for 14 weeks. There are no prerequisites other than graduate standing in engineering. Proficiency in calculus, differential equations, linear algebra, and computer programming is required. Students find that previous experience in space dynamics, linear multivariable control, or optimal control is helpful.

The goal of the book and course is for students to develop fundamental skills needed to do professional work in the area of spacecraft guidance. After working through the book, students should …

Analysis Of Localization Algorithms For Wireless Sensor Networks Using Binary Data, Alexander Joseph Hart

Graduate Research Theses & Dissertations

The detection, localization, and tracking of environmental and physical conditions can be accomplished using wireless sensor networks (WSNs). Recent advancements in sensors, processors, and wireless communications have improved the quality and acquisition speed of data in WSNs. However, the data gathered by a WSN is inherently random due to component and environmental variations. Thus, statistical signal processing algorithms are needed to analyze the random data in a robust way. Though many algorithms for the analysis of random data are established and available, they are problem-specific and must be adapted to the application. This thesis provides an analysis of established localization …

Optimization Of Ported Cfd Kernels On Intel Data Center Gpu Max 1550 Using Oneapi Esimd, Mohammad Zubair, Aaron Walden, Gabriel Nastac, Eric Nielsen, Christoph Bauinger, Xiao Zhu

Computer Science Faculty Publications

We describe our experience porting FUN3D’s CUDA-optimized kernels to Intel oneAPI SYCL.We faced several challenges, including foremost the suboptimal performance of the oneAPI code on Intel’s new data center GPU. Suboptimal performance of the oneAPI code was due primarily to high register spills, memory latency, and poor vectorization. We addressed these issues by implementing the kernels using Intel oneAPI’s Explicit SIMD SYCL extension (ESIMD) API. The ESIMD API enables the writing of explicitly vectorized kernel code, gives more precise control over register usage and prefetching, and better handles thread divergence compared to SYCL. The ESIMD code outperforms the optimized SYCL …

Design Of An Internal Osculating Waverider Intake, Mark E. Noftz, Andrew J. Shuck, Joseph S. Jewell, Jonathan Poggie, Andrew N. Bustard, Thomas J. Juliano, Nicholas J. Bisek

Publications

The design of an inward-turning, high-speed, three-dimensional streamline traced intake is presented from osculating axisymmetric theory. To satisfy the osculating intake design criteria, a stitched Busemann diffuser and Internal Conical Flow-A solution is used as the basic isentropic compressive streamline. This new contour provides efficient compression, high flow uniformity, and straight leading edge shocks of equal strength. Additionally, a novel method for constructing the inlet cowl is presented. The combined process leads to a new method of high-speed intake design. A generic shape-transitioned intake is constructed and named the Indiana Inlet for the Indiana universities that contributed to the project. …

Simplified Mass And Inertial Estimates For Aircraft With Components Of Constant Density, Benjamin C. Moulton, Douglas F. Hunsaker

Mechanical and Aerospace Engineering Student Publications and Presentations

Aircraft mass and inertial properties are required for predicting the dynamics and handling qualities of aircraft. However, such properties can be difficult to estimate since these depend on the external shape and internal structure, systems, and mass distributions within the airframe. Mass and inertial properties of aircraft are often predicted using computer-aided design software, or measured using various experimental techniques. The present paper presents a method for quickly predicting the mass and inertial properties of complete aircraft consisting of components of constant density. Although the assumption of constant density may appear limiting, the method presented in this paper can be …