Engineering Commons^™

A Study Of A Wind Tunnel Measurement System For Unsteady Pressures Using Pneumatic Transmission Lines, Mohammed Javed Khan

Theses and Dissertations

The application of pneumatic transmission lines theory to a tube-scanning valve system for unsteady pressure measurements in the AFIT 5-foot wind tunnel is investigated. Transfer gains of various tube-scanning valve configurations were experimentally measured and the validity of a theoretical model verified for a frequency range of 20 Hz to 140 Hz. The selected system having a 0.0625-in. ID flexible tube of 84 in. length connected to a scanning valve was installed in the wind tunnel. Unsteady pressures introduced over an 18 percent airfoil at zero angle of attack were measured with this system. Data were collected for 0, 40, …

An Experimental Investigation Of A Turbulent Boundary Layer With Suction Through Closely Spaced Streamwise Slots, Stephen P. Wilkinson

Mechanical & Aerospace Engineering Theses & Dissertations

The object of this research was to experimentally evaluate a suction surface for use with incompressible turbulent boundary layers. The surface consisted of an array of closely spaced slots aligned in the direction of the free stream flow. Direct drag and mean boundary layer velocity profile measurements showed that the slotted surface had nominally the same suction characteristics as the porous surface.

Testing Of Solar Collectors By A Standard Method, Harry J. Sauer Jr., Bassem F. Armaly

UMR-MEC Conference on Energy / UMR-DNR Conference on Energy

A description of the recently adopted standard for testing solar collectors "ASHRAE STANDARD 93-77, METHOD OF TESTING SOLAR COLLECTORS BASED ON THERMAL PERFORMANCE" is presented. Results from the standard could be used to simulate the transient performance of an installed solar system.

Performance Of A Dual-Range Cloud Nucleus Counter., Darryl J. Alofs

Mechanical and Aerospace Engineering Faculty Research & Creative Works

An Instrument for Measuring the Concentrations of Cloud Condensation Nuclei as a Function of Nucleus Critical Supersaturation (S//c) is Described. in the Range 0. 1% Less Than Equivalent to S//c Less Than Equivalent to 0. 1%, the Instrument is Operated as a Vertical Flow Thermal Diffusion Chamber. in the Range of 0. 016% Less Than Equivalent to S//c Less Than Equivalent to 0. 1%, the Chamber is Operated at 100% Humidity, and the Equilibrium Radii of the Nuclei Are Measured with an Optical Counter. This Paper Presents a Large Body of Data Taken in the Laboratory to Evaluate the Performance …

A Small Horizontal Axis Wind Turbine Feeding Power Into The Utility Grid, G. C. Thomann, M. Jong, M. H. Snyder

UMR-MEC Conference on Energy / UMR-DNR Conference on Energy

A small horizontal axis wind turbine, with about a 2 kW power output, was constructed to convert wind energy into AC power to be fed into the utility grid. The machine is intended to model operation of the larger wind generators now being built. The variable pitch rotor is 18 ft in diameter and has a GA(W)-1 blade airfoil. The rotor is fabricated from sitka spruce mounted on a commercial propeller/hub system. Rotor speeds of from 75 to 150 rpm are used in operation. A chain drive and helical gear drive system steps up rotor speed to 1800 - 3600 …

Airfoil Data For Use Of Wind Turbine Designers, Melvin H. Snyder

UMR-MEC Conference on Energy / UMR-DNR Conference on Energy

This paper reviews design procedures for wind-axis turbine rotors. An "on-design" routine for rotor blade design is presented as well as an "off-design" performance calculation program. Resulting from this review are analyses of desirable characteristics of airfoil sections and of types of data which rotor designers need. Included in the paper are airfoil characteristics for candidate blade sections including 360 degree data for GA(W)-1 and GA(W)-2 airfoils.

Low Head Power Generation With Bulb Turbines, J. L. Carson, R. S. Samuelson

UMR-MEC Conference on Energy / UMR-DNR Conference on Energy

Because of uncertainties, delays, and high costs associated with alternative electric energy sources, many agencies responsible for generation of electrical power are investigating means of replacing or supplementing their existing hydroelectric facilities. In the head range between 10 and 60 feet, the bulb-type generating unit, in which the generator is enclosed in a metal capsule within the water passage, has many advantages, including higher efficiency and lower cost, over other types of turbines. Two of the municipalities in the United States which have recently conducted feasibility studies for installing bulb turbines in their systems are the City of Idaho Falls, …

Static Temperature Measurements In Supersonic Flow Using Lasar Raman Spectroscopy, Paul A. Nystrom

Mechanical & Aerospace Engineering Theses & Dissertations

Laser Raman spectroscopy is a nonintrusive technique which can generate mean static temperature (MST) data within flow fields. By ratioing two simultaneously gathered portions of the Raman scattered spectrum, absolute intensity measurements were not needed. This method was applied to a supersonic cold air jet, where the NST ranged from 160'K to 300'K. Accurate measurements were not realized due to the presence of flow contaminates, especially water vapor.

Evaluation Of Hydrogen As A Cryogenic Wind Tunnel Test Gas, Richard Carl Haut Ii

Mechanical & Aerospace Engineering Theses & Dissertations

A theoretical analysis of the properties of hydrogen has been made to determine the suitability of hydrogen as a cryogenic wind tunnel test gas. By using Cryogenic hydrogen, instead of air or cryogenic nitrogen, as the wind tunnel test gas, a significant increase in the test Reynolds number may be achieved without increasing the aerodynamic loads. Under sonic conditions, for example, compared to air at ambient temperature, cryogenic hydrogen at a pressure of one atmosphere produces an increase in Reynolds number of a factor of approximately fourteen while cryogenic nitrogen, at the same pressure, produces an increase of only a …

The Sun's Wind, Alexei Leonov

Articles

This book is on display here for educational purposes only.

Unless stated otherwise within this repository collection, all materials are shared under the following Creative Commons license: [Creative Commons Attribution-NonCommercial 4.0 International License].

Written and illustrated in 1977 by Soviet cosmonaut Alexei Leonov.
Published by Progress Publishers in Moscow

Mixed Convection Across A Horizontal Cylinder With Uniform Surface Heat Flux, A. Mucoglu, T. S. Chen

Mechanical and Aerospace Engineering Faculty Research & Creative Works

No abstract provided.

Optimal Cantilever Dynamic Vibration Absorbers, R. G. Jacquot, J. Earl Foster

Mechanical and Aerospace Engineering Faculty Research & Creative Works

This work considers the use of a double-ended cantilever beam as a distributed parameter dynamic vibration absorber applied to a single-degree-of-freedom system in the presence of sinusoidal forces. The problem is analyzed exactly and by an energy approach using a single mode approximation for the cantilever beam. The results for both techniques compare favorably and damping is introduced in the form of a complex beam modulus. Optimal tuning and optimal damping parameters are found for a given ratio of absorber mass to main mass. © 1977 by ASME.

Studies Of Vibrational Surface Modes In Ionic Crystals. I. Detailed Shell-Model Studies For The Unrelaxed (001) Face Of Seven Crystals Having The Rocksalt Structure, T. S. Chen, F. W. De Wette, G. P. Alldredge

Mechanical and Aerospace Engineering Faculty Research & Creative Works

We present a comprehensive, unified account of the lattice dynamics of unrelaxed (001) faces of seven crystals having the rock salt structure, three of which have an absolute gap between the acoustical and optical bulk bands (RbF, RbCl, and NaI) and four of which have overlap between these bulk bands (NaF, NaCl, LiF, and MgO). The results are obtained from calculations of the normal modes of a thin crystal film in which the ionic interactions are described by the rigid-shell model. An outline of the formulation of the shell model for the film is given, and the rapid convergence of …

Predicting Natural Frequencies Of A Hydrodynamically Lubricated Journal Bearing With Constant Oil Supply Pressure, D. C. Edwards, N. Khorzad, Charles L. Edwards

Mechanical and Aerospace Engineering Faculty Research & Creative Works

The analytical and experimental investigations reported here deal with the natural frequencies and system behavior of a full journal bearing subjected to a small sinusoidal load superimposed on a large unidirectional static load. The analysis, verified by experimentation, shows that the bearing can be regarded as two independent second-order systems acting perpendicular to each other. The variable coefficients of the equations of motion cause the bearing to behave as an underdamped system for low values of static eccentricity ratio to, and as an overdamped system for intermediate values of to. The bearing tends to be unstable above a particular to. …

A Closed-Form Solution For The Radiosity At The Edge Of A Rectangular Cavity, Alfred L. Crosbie

Mechanical and Aerospace Engineering Faculty Research & Creative Works

No abstract provided.

Development Of Helicopter Flight Path Models, Alfred Fermelia, Donald A. Gyorog, V. J. Flanigan

Mechanical and Aerospace Engineering Faculty Research & Creative Works

The objective of this paper is to present general techniques for simulating helicopter flight trajectory response. During flight the pilot manipulates the controls either to trim the helicopter for steady flight by balancing the external forces and moments or to produce a desired maneuver by controlling the unbalance of these forces and moments. Discussions of the physical phenomena involved with the aerodynamics of the rotors and fuselage are given in [1] through [3]. The simulated control function will be composed forward-aft cyclic, lateral cyclic, pedal, and collective. This control will be represented by the vector

Deformation Produced By A Simple Tensile Load In An Isotropic Elastic Body, R. C. Batra

Mechanical and Aerospace Engineering Faculty Research & Creative Works

It is shown that a simple tensile load produces a simple extension provided the empirical inequalities (Truesdell and Noll [1], eqn. 51.27) hold. © 1976 Noordhoff International Publishing.

Bit Penetration Into Rock-A Finite Element Study, J. K. Wang, T. F. Lehnhoff

Mechanical and Aerospace Engineering Faculty Research & Creative Works

The sequence of rock failure mechanisms and quantitative information on stress, displacement and material failure in the process of bit penetration have been obtained through computer simulation. A finite element approach has been developed to simulate bit penetration from bit-rock interaction to chip formation. A mathematical rock failure model, based on available rock failure experiments, has been proposed to represent post-failure rock behavior and applied in the penetration simulations. The finite element code was developed for two-dimensional plane strain problems to consider non-linear material properties, geometric non-linearity, and fracture propagation. An anistropic element as well as variable stiffness and stress …

Numerical Simulation Of A Widely Used Cloud Nucleus Counter., Darryl J. Alofs, J. C. Carstens

Mechanical and Aerospace Engineering Faculty Research & Creative Works

The Performance of the Conventional Horizontal Plate Thermal Diffusion Chamber as a Cloud Nucleus Counter Was Studied. Numerical Calculations Were Performed in Order to Follow the Simultaneous Drop Growth and Sedimentation in the Spatially and Temporally Nonuniform Supersaturation Field. the Effect of Nuclei Distribution and Smallest Detectable Drop Size Were Investigated. the Results Indicate Order of Magnitude Uncertainty in the Count at 0. 1% Supersaturation, and a Factor of 2 Uncertainty at 1. 0% Supersaturation.

Mie Scattering Computations For Moderately Large Spherical Particles, Dwight C. Look

Mechanical and Aerospace Engineering Faculty Research & Creative Works

No abstract provided.

The Effects Of Main-Flow Radial Velocity On The Stability Of Developing Laminar Pipe Flow, F. C.T. Shen, T. S. Chen, L. M. Huang

Mechanical and Aerospace Engineering Faculty Research & Creative Works

In studying the stability due to axisymmetric disturbances of the developing flow of an incompressible fluid in the entrance region of a circular tube, a generalized version of the Orr-Sommerfeld equation was derived which takes account of the radial velocity component in the main flow. The new terms in the generalized Orr-Sommerfeld equation are inversely proportional to the Reynolds number. The resulting eigenvalue problem consisting of the disturbance equation and the boundary conditions was solved by a direct numerical integration scheme along with an iteration procedure. Neutral stability curves and critical Reynolds numbers at various axial locations are presented. A …

Apollo/Soyuz Tv Guide: "Soyuz, Soyuz, This Is Apollo...", Bob Button

Articles

This is a TV Guide from 1975 that features a story about the televised Apollo/Soyuz mission.

Analysis Of Spread Multi-Jet Vtol Aircraft In Hover, Leroy F. Albang

Mechanical & Aerospace Engineering Theses & Dissertations

An investigation of VTOL aircraft lift losses in hover has been conducted to evaluate a method for a simplified test technique. Three flat plate models were tested to determine their usefulness in predicting hover characteristics by comparing results between plate and three­ dimensional models. Attempts to correlate the out of ground effect results for the plate models with the empirical expression for calculating jet-induced loads were successful for the models which used engine simulators producing efflux characteristics similar to the three­ dimensional model engines. Data for the model using engine simulators with characteristics unlike those of the three-dimensional model simulators …

An Experimental Investigation Of A Cold Jet With Solid Centerbody Emitting From A Flat Plate Into A Subsonic Free Stream, Danny K. Livingston

Mechanical & Aerospace Engineering Theses & Dissertations

A study of the influence of a solid center body on lift loss and pitching moment has been conducted. It has been well established that a round free jet emitted from a flat plate at right angles to a cross flow causes an induced pressure distribution on the plate which adversely affects the lift and pitching stability of the flat plate.

This investigation has employed a 2.58 - cm diameter round jet with a 1.91 - cm diameter solid rounded core in order to modify the induced flow field and attempt to reduce the lift loss and pitching moment. Preliminary …

The Application Of Impact Dampers To Continuous Systems, Ranjit K. Roy, Richard D. Rocke, J. Earl Foster

Mechanical and Aerospace Engineering Faculty Research & Creative Works

A study has been made of the application of impact dampers to two types of continuous systems, a simply supported and a clamped beam. Experimental models were tested in the laboratory and computer programs were developed to calculate response by two separate approaches. Results from calculations agreed favorably with experimental tests. Curves presented show the response to be expected for values of significant system parameters and enable the user to apply impact dampers to these types of continuous systems. © 1975 by ASME.

Transport Phenomena In Thermally Stratified Boundary Layers, D. W. Pepper, S. C. Lee

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Studies of heat, mass, and momentum transfer are made to analyze the formation of marine fogs in thermally stratified boundary layers in the atmosphere. The governing partial differential equations of continuity, momentum, temperature, and concentration are used to describe the transport phenomena. An additional equation of turbulence energy is introduced to account for the development of the turbulent motions. Simultaneous solution of this system of equations allows the turbulent exchange coefficients to be treated in the same way as all other dependent parameters. Verification of the theoretical approach is made by comparing the numerical predictions with wind tunnel simulations of …

Measurement Of Growth Rate To Determine Condensation Coefficients For Water Drops Grown On Natural Cloud Nuclei., A. M. Sinnarwalla, Darryl J. Alofs, J. C. Carstens

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Growth Rate Measurements Were Made for Water Drops Grown on Nuclei in Atmospheric Air Samples Taken in Rolla, Missouri. Rolla, Having a Population of 15,000 and Very Little Industry, is Relatively Free of Urban Pollutants. the Measurements Were Made in a Vertical Flow Thermal Diffusion Chamber at Supersaturations of 0. 5 and 1%. the Time to Grow from Near Dry Radius to the Final Radius (6 to 7. 5 Mu M) Was Measured. If One Assumes the Thermal Accomodation Coefficient is Unity, the Measurements Indicate an Average Value of 0. 026 for the Condensation Coefficient. the Temperature Ranged from 22. …

Thermal Stresses In A Sphere Due To Local Heating Followed By Complete Cooling, T. S. Chen, K. Thirumalai, J. B. Cheung

Mechanical and Aerospace Engineering Faculty Research & Creative Works

No abstract provided.

Photoionization Of The 6p32,122 Fine-Structure Levels In Cesium, Kaare J. Nygaard, Robert E. Hebner, James A. Jones, Robert J. Corbin

Physics Faculty Research & Creative Works

The relative photoionization cross sections for cesium atoms selectively excited to the 6P32,122 states have been measured in a triple-crossed-beam experiment. A cesium discharge lamp produced resonant wavelengths of 8521 and 8944 for the excitation process. A Hg-Xe lamp combined with a grating monochromator was used for the actual ionization in the wavelength region from 2500 to 5000. Background counts due to photoionization of ground-state cesium atoms and dimers as well as various surface effects were discriminated against by chopping the excitation light source. The data are compared with results from radiative-recombination measurements in which the fine-structure levels are not …

"Thomas Stafford" - Astronauts & Cosmonauts Cultural Exchange Album, Thomas P. Stafford

Articles

This is a photo album of the cultural exchange visit between the American astronauts and Soviet cosmonauts of the Apollo-Soyuz Mission.

The front cover reads "Thomas Stafford"