Operations Research, Systems Engineering and Industrial Engineering Commons^™

A Novel Approach To Control Corrosion Behaviour On Bio Materials Using Taguchi Method (Design Of Experiments), Sai Dhiresh Kilari

Open Access Theses & Dissertations

In the present work, the Taguchi method, from the design of experiment (DOE) has been used to optimize the dip testing method to test the corrosion resistance of bio degradable materials such as PLA (Polylactic acid)and PCL (Polycaprolactone). A L9 (9) orthogonal array of Taguchi design was used, which involves nine experiments for three parameters (pH, sample, temperature) with three levels was used. Corrosion resistance in various pH change of HCL solution was evaluated by dip tests at various temperatures. Analysis of variance (ANOVA) is performed on the obtained measured data and S/N (signal to noise) ratios. The lower the …

Enhancing Surface Finish Of Fused Deposition Modeling Parts Through Targeted Chemicals And Design Of Experiments, Saurabh Nayyar Nayyar

Open Access Theses & Dissertations

Fused Deposition Modeling (FDM) is one of the most popular rapid prototyping (RP) technologies due to its low operational cost, high fabrication speed, and range of applications served. However, FDM fabricated parts generally have poor surface finish quality which have limited their utilization in end-use applications. To enhance surface quality of FDM materials, several researchers have regulated key process parameters using the FDM material, Acrylonitrile Butadiene Styrene (ABS), with varying results. The main goal of this research is to investigate the effects of a post-fabrication chemical treatment process on the surface roughness for FDM parts of the FDM material ULTEM. …

Period Batch Control - A Production Planning System Applied To Virtual Manufacturing Cells, Z. Tesic, B. Stevanaov, V. Jovanovic, M. Tomic, C. Kafol

Engineering Technology Faculty Publications

Period Batch Control (PBC) system has been known for its implementation with the classical group technology (GT) cells, and it has been known for its simplicity. The main production planning decisions concern the choice of the period length and the stage number and contents. Also, in order to better integrate the production planning with the application of GT cells at the shop floor, the concept of virtual manufacturing cells has been applied. Since virtual cells configurations are changing periodically, a model for implementing the PBC system into virtual manufacturing cells environment is developed. The model enables alignment of the PBC …

Pilot Programs For Veterans Transition To Engineering Fields, Vukica M. Jovanovic, Anthony W. Dean, Carol L. Considine, Karina Arcaute, Petros Katsioloudis, Mileta Tomovic, Thomas B. Stout, Connor Schwalm, Jennifer G. Michaeli, Yuzhong Shen

Engineering Technology Faculty Publications

Veterans, through their active service, frequently receive training in highly skilled technical areas. However, they may lack a theoretical background in underlying engineering principles. They also need additional support with the transition from a highly structured military environment to an environment with more ambiguous time constraints and different sorts of responsibilities. Moreover they are facing challenges which are specific for their student population. Therefore, enabling multiple mechanisms which would support them and provide them necessary guidance are especially important at universities with large veteran populations such as at Old Dominion University in Norfolk, Virginia. Hence, there is a need for …

The Influence Of Operational Resources And Activities On Indirect Personnel Costs: A Multilevel Modeling Approach, Bradley C. Boehmke, Alan W. Johnson, Edward D. White, Jeffery D. Weir, Mark A. Gallagher

Faculty Publications

Indirect activities often represent an underemphasized, yet significant, contributing source of costs for organizations. In order to manage indirect costs, organizations must understand how these costs behave relative to changes in operational resources and activities. This is of particular interest to the Air Force and its sister services, because recent and projected reductions in defense spending are forcing reductions in their operational variables, and insufficient research exists to help them understand how this may influence indirect costs. Furthermore, although academic research on indirect costs has advanced the knowledge behind the modeling and behavior of indirect costs, significant gaps in the …

Improving Machine Changeover/Setup Times By Increasing U.S. Manufacturers' Knowledge Of 5s, Nicole Schra-Martin

Walden Dissertations and Doctoral Studies

The 5S process is one of the techniques born out of Japanese manufacturing. Ohno, the developer of 5S, found that when manufacturing waste is eliminated, costs are reduced and profits increase. This is the bases of 5S and this research. The cost of U.S. manufactured products is higher compared to the cost of products from other global manufacturers that use 5S. This study was conducted to determine if implementing 5S in U.S. manufacturing could change U.S. manufacturing cost and if using 5S could impact U.S. manufacturing. The research questions focused on the relationship between 5S and changeover/setup times on production …

System-Wide Prediction Of General, All-Cause, Preventable Hospital Readmissions, Ken Musselman, Brandon Pope, Steve Witz, Zhiyi Tian, Lingsong Zhang, Linda Leon, Ann Davis

RCHE Publications

Existing studies of hospital readmissions typically focus on specific diagnoses, age groups, discharge dispositions, payer classes, or hospitals, and often use small samples. It is not clear how predictive models generated from such studies generalize across diseases, hospitals, or time periods. In this study, a logistic regression model of readmission risk within 30 days based on hospital administrative data was constructed and validated across hospitals and time periods. The hospitals included both general and specialty hospitals such as long-term care, women’s, and children’s hospitals. The administrative data included information on patient’s demographics, diagnoses, procedures, and discharge disposition. Derivation and validation …

Pre-Mission Input Requirements To Enable Successful Sample Collection By A Remote Field/Eva Team, Barbara A. Cohen, Darlene S. S. Lim, Kelsey E. Young, Anna Brunner, Richard C. Elphic, Audrey Horne, Mary C. Kerrigan, Gordon O. Osinski, John R. Skok, Steven W. Squyres, David Saint-Jacques, Jennifer L. Heldmann

Journal of Human Performance in Extreme Environments

We used a field excursion to the West Clearwater Lake Impact structure as an opportunity to test factors that contribute to the decisions a remote field team (for example, astronauts conducting extravehicular activities (EVA) on planetary surfaces) makes while collecting samples for return to Earth. We found that detailed background on the analytical purpose of the samples, provided to the field team, enables them to identify and collect samples that meet specific analytical objectives. However, such samples are not always identifiable during field reconnaissance activities, and may only be recognized after outcrop characterization and interpretation by crew and/or science team …

Collecting Unsolicited User-Generated Change Requests, Joseph W. Goldsmith

Theses and Dissertations

Unlike aircrew directly associated with acquisitions, line operators are not fully engaged in the methods to push materiel hardware or software change requests up the chain, to a decision maker, and then to the engineers. The Air Force trains these end users to logically apply expert systems knowledge to execute the mission but has not fully leveraged this resource for properly identifying and correcting operational shortfalls in an aircraft's design. Focusing on the Remotely Piloted Aircraft (RPA) community, the research goal is to determine if the Air Force should establish a formal program for collecting and prioritizing unsolicited user change …

Continuous Decision Support, Jeremy P. Hendrix

Theses and Dissertations

Organizations are often faced with portfolio construction efforts that require them to select one or more alternatives, subject to resource constraints, with the aim of achieving the maximum value possible. This is a well-defined problem with a number of analytically defensible approaches, provided the entire set of alternatives is known when the decision event takes place. Less well treated in the literature is how to approach this problem when the entire set of alternatives is unknown, as when the alternatives arrive over time. This change in the availability of data shifts the problem from one of identifying an optimal subset …

Application Of Executable Architectures In Early Concept Evaluation, Ryan M. Pospisal

Theses and Dissertations

This research explores use of executable architectures to guide design decisions in the early stages of system development. Decisions made early in the system development cycle determine a majority of the total lifecycle costs as well as establish a baseline for long term system performance and thus it is vital to program success to choose favorable design alternatives. The development of a representative architecture followed the Architecture Based Evaluation Process as it provides a logical and systematic order of events to produce an architecture sufficient to document and model operational performance. In order to demonstrate the value in the application …

Predictive Modeling Of Fuel Efficiency Of Trucks, Srivatsa Bindingnolle Narasimha

Graduate Dissertations and Theses

This research studied the behavior of several controllable variables that affect the fuel efficiency of trucks. Re-routing is the process of modifying the parameters of the routes for a set of trips to optimize fuel consumption and also to increase customer satisfaction through efficient deliveries. This is an important process undertaken by a food distribution company to modify the trips to adapt to the immediate necessities. A predictive model was developed to calculate the change in Miles per Gallon (MPG) whenever a re-route is performed on a region of a particular distribution area. The data that was used, was from …

Developing And Testing An Anguilliform Robot Swimming With Theoretically High Hydrodynamic Efficiency, John B. Potts Iii

LSU New Orleans Theses and Dissertations

An anguilliform swimming robot replicating an idealized motion is a complex marine vehicle necessitating both a theoretical and experimental analysis to completely understand its propulsion characteristics. The ideal anguilliform motion within is theorized to produce ``wakeless'' swimming (Vorus, 2011), a reactive swimming technique that produces thrust by accelerations of the added mass in the vicinity of the body. The net circulation for the unsteady motion is theorized to be eliminated.

The robot was designed to replicate the desired, theoretical motion by applying control theory methods. Independent joint control was used due to hardware limitations. The fluid velocity vectors in the …

Electromechanics Of An Ocean Current Turbine, Vasileios Tzelepis

LSU New Orleans Theses and Dissertations

The development of a numeric simulation for predicting the performance of an Ocean Current Energy Conversion System is presented in this thesis along with a control system development using a PID controller for the achievement of specified rotational velocity set-points. In the beginning, this numeric model is implemented in MATLAB/Simulink® and it is used to predict the performance of a three phase squirrel single-cage type induction motor/generator in two different cases. The first case is a small 3 meter rotor diameter, 20 kW ocean current turbine with fixed pitch blades, and the second case a 20 …

Ergonomic Analysis Of Mobile Cart–Assisted Stocking Activities Using Electromyography, Sohyung Cho

SIUE Faculty Research, Scholarship, and Creative Activity

Workers in grocery stores are exposed to numerous musculoskeletal risks that can be reduced using assistive devices while performing stocking tasks. A regional grocery store has recently deployed a mobile cart without comprehension of its ergonomic impact on workers, which this article investigates using normalized electromyography data (%MVC). This article studies not only ergonomic impact based on %MVC values but also work performance represented by a muscle force metric (MFM). The results from this study showed highest muscle groups in %MVC and MFM were the erector spinae and triceps. Interestingly, muscle activations on erector spinae were reduced when mobile cart …

On Valuing Biopharmaceutical Product Pipelines: An Effectuation Model And Evidence, Mark J. Ahn, Anne S. York, Wei Wu, Yulianto Suharto, Tugrul Unsal Daim

Engineering and Technology Management Faculty Publications and Presentations

New creative approaches are needed to manage emerging biotechnology innovations, regulations, and payor environments to enhance product pipeline productivity, valuation, and risk management. Biopharmaceutical firms must make dynamic resource allocation decisions on their relative levels of internal R&D and external strategic alliances in furthering their pipelines. As the predominant method of using discounted cash flow (DCF) methodologies may lead to chronic underinvestment and performance, we evaluated the integration of traditional DCF with an effectuation model of analysis. Unlike traditional financial models that begin with the end goal of assumed known cash flows and recursively solve for portfolio optimization, the effectuation …

Efficient Detection Of Zero-Day Android Malware Using Normalized Bernoulli Naive Bayes, Luiza Sayfullina, Emil Eirola, Dmitry Komashinsky, Paolo Palumbo, Yoan Miche, Amaury Lendasse, Juha Karhunen

Engineering Management and Systems Engineering Faculty Research & Creative Works

According to a Recent F-Secure Report, 97% of Mobile Malware is Designed for the Android Platform Which Has a Growing Number of Consumers. in Order to Protect Consumers from Downloading Malicious Applications, There Should Be an Effective System of Malware Classification that Can Detect Previously Unseen Viruses. in This Paper, We Present a Scalable and Highly Accurate Method for Malware Classification based on Features Extracted from Android Application Package (APK) Files. We Explored Several Techniques for Tackling Independence Assumptions in Naive Bayes and Proposed Normalized Bernoulli Naive Bayes Classifier that Resulted in an Improved Class Separation and Higher Accuracy. We …

Swerve, Kaitlin A. Castillo, Cichasky A. Catherine

Industrial and Manufacturing Engineering

Carpooling yields great benefits environmentally, socially, and economically for carpooling, however there is no easy to use, safe, and enjoyable application for people to connect with others who are both close in proximity and have schedules that match currently. By creating a database and visual mock ups, our senior project creates the basis for an application called Swerve that matches users by location and schedules and has social and economic incentives. Our research allowed us to further understand the social, environmental and economic benefits and incentives of carpooling. We also looked into current carpooling websites and applications and could not …

Startup Social Responsibility: A Concentrated Social Audit Of Halt Medical Inc., Matthew Frank Rosa

Industrial and Manufacturing Engineering

Halt Medical Inc. is a biomedical device startup whose managers are interested in assessing their levels of employee satisfaction and organizational well-being. They want to know if their employees are cooperating, if departments are cohesive, and if everyone is happy. To evaluate Halt Medical’s social capital and environment, a social responsibility audit will be conducted concentrated specifically on the organization’s social and ethical initiatives to its employees. This analysis requires interviews of managers, observations of cultural diffusion, and employee opinions on a variety of business areas. The five areas of focus for this audit are the company’s accommodation of each …

Multi-Restaurant Delivery Service Design And Financial Analysis, Dylan Davis Fuller

Industrial and Manufacturing Engineering

When found on campus all day and in need of a quick meal before the next class what are the options for you as a Cal Poly student or faculty? Campus dining is the only option that can meet the typical demand you have of speed and convenience. Restaurants with food delivery often don’t have the variety or take to long for delivery. The goal is to provide a delivery service with the speed of getting a meal on campus but with the variety and quality of the restaurants found in downtown San Luis Obispo. Looking at existing businesses providing …