Engineering Science and Materials Commons^™

Blade Design And Validation Of Hydrokinetic Turbine To Harvest Water Current Energy, Setare Sadeqi

LSU New Orleans Theses and Dissertations

The innovative aspect of this research lies in the careful integration of cutting-edge technologies throughout the entire process of designing, fabricating, and testing the carbon fiber propeller for the 3-bladed horizontal axis ocean current turbine (OCT). SolidWorks software played a pivotal role in the initial design phase, enabling a meticulous and precise modeling of the propeller's geometry. The utilization of SolidWorks allowed for a detailed exploration of various design parameters, ensuring that the propeller's structure and form were optimized for performance in ocean current conditions. Moving beyond the realm of virtual design, the choice of carbon fiber as the fabrication …

Investigation On The Effects Of Biofouling On The Boundary Layer, Adam N. Bacon

LSU New Orleans Theses and Dissertations

This study is an investigation of the effect of biofouling on the boundary layer of a flat plate and a NACA 4-digit series foil. Three identical hydrofoils made of resin were placed in the Gulf of Mexico at Grand Isle, Louisiana, and observed and analyzed by marine biologists at the University of New Orleans for their species composition. The resulting biofouling that grew was primarily made up of barnacles and bryozoans. The foils were submerged in an open channel flume at zero incidence and subjected to a series of experiments whose arc-length Reynolds numbers ranged from approximately 13000 to 32000. …

Towing Tank Trials Of Hydrokinetic Turbine Scale Model To Support Marine Energy System Verification, Shahab Rouhi

LSU New Orleans Theses and Dissertations

In response to the escalating demand for sustainable energy solutions and the critical reevaluation of conventional fossil fuels due to environmental concerns, this dissertation embarks on a comprehensive exploration of hydrokinetic energy as a promising alternative. The study delves into the underexplored domain of hydrokinetic energy, leveraging innovative methodologies for effective utilization and harnessing, particularly through the development and investigation of hydrokinetic turbines.

In the realm of hydrokinetic energy conversion, our research has exclusively concentrated on horizontal-axis turbines, distinct from other turbine configurations. Noteworthy is the adaptation of a conventional horizontal-axis wind turbine for water currents, revealing enhanced performance through …

Cal Poly Fluid Power Vehicle Challenge 2024, J. Mason Gray, Ryan D'Amour, Alberto Acho Lopez, Christian Ferrandino, Johnathan Dietz

Mechanical Engineering

In this Final Design Review, the Cal Poly Fluid Power Vehicle Team competed in Norgren’s 2024 Fluid Power Vehicle Challenge. The design need of the competition was for college teams to compete with human-powered, hydraulic-driven vehicles in an endurance race, a sprint race, an efficiency race, and a regenerative power race. The competition need was to design a vehicle to win in as many races as possible, achieving the highest overall score and winning the competition. With a design emphasis on the endurance and sprint race, the Cal Poly team designed a fluid power system that fastened to a purchased …

Numerical Simulation Of Laser Induced Elastic Waves In Response To Short And Ultrashort Laser Pulses., Alireza Zarei

All Dissertations

In an era of intensified market competition, the demand for cost-effective, high-quality, high-performance, and reliable products continues to rise. Meeting this demand necessitates the mass production of premium products through the integration of cutting-edge technologies and advanced materials while ensuring their integrity and safety. In this context, Nondestructive Testing (NDT) techniques emerge as indispensable tools for guaranteeing the integrity, reliability, and safety of products across diverse industries.

Various NDT techniques, including ultrasonic testing, computed tomography, thermography, and acoustic emissions, have long served as cornerstones for inspecting materials and structures. Among these, ultrasonic testing stands out as the most prevalent method, …

A Methodology For Determining Optimal Milling Parameters For Low-Taper Microtensile Sample Production, Zachary Wayne Barker

Open Access Theses & Dissertations

Femtosecond lasers are beginning to see an increase in interest for industrial and high throughput microsample milling applications. Despite this, much of the literature regarding removal rate studies for ultrashort pulse laser milling continues to focus on single-pulse or similar experiments that have a very small time on target. The material volume removal rates of femtosecond milling can vary wildly depending on parameters like laser scan speed, hatch spacing, z-axis step size, and pulses on the material. Currently, there is no established methodology for determining the optimal values of these parameters for micromilling applications. This methodology was developed in this …

Effect Of The Microstructure On The Corrosion Behavior Of Alcunimn And Alcunimnsi High Entropy Alloys In A 3.5wt% Nacl Solution, Celine Chiong

Open Access Theses & Dissertations

In this study, the AlCuNiMn and AlCuNiMnSi high entropy alloys (HEAs) are investigated to characterize the effect of Si addition and subsequent annealing treatments on the corrosion behavior in a 3.5wt% NaCl solution at room temperature. The microstructure evolution from the as-received condition and after annealing at 600°C, 800°C, and 1000°C for 24 hours in air is examined. The microstructural transformation of HEAs is extensively reported in the literature. However, its impact on the corrosion resistance of HEAs has not received the same attention. In this study, an increase in the annealing temperature of the base AlCuNiMn alloy improved the …

Laser Powder Directed Energy Deposition (Lp-Ded) Inconel 718: Laser Power And Heat Treatment Effect On Microstructure And Mechanical Properties, Dana Victoria Godinez

Open Access Theses & Dissertations

This study examines the microstructure and mechanical properties (tensile, hardness, and fatigue endurance) of laser powder-directed energy deposition (LP-DED) printed specimens with varying deposition parameters. Five samples with power inputs ranging from 350 to 2620W, all of similar thicknesses, were evaluated to enable a direct comparison. The varying specimens were heat treated, including stress relief, hot isostatic pressing, solution, and two-step aging. The resulting microstructures and their corresponding hardness values were compared at each heat treatment stage. The fully heat-treated specimens' tensile properties and fatigue life were also examined and compared. Key findings of this study indicate that complete heat …

Feasibility Study For The Detection Of Damage To Composite Overwrapped Pressure Vessels With Phase Array Ultrasonic Testing, Jordan Scott Hitter

Open Access Theses & Dissertations

When discussing the field of Nondestructive Examination, there are various techniques and instrumentation that can be utilized for analysis of components. However, with newer technology and the development of newer forms of technique, it is critical to explore exactly how these can be applied. This work will aim to explore one newer technique, Phased Array Ultrasonic Testing, and determine the viability of its use for examining Composite Overwrapped Pressure Vessels (COPVs). Currently, the types of vessels have been used in a variety of ways such as in transportation vehicles. More notably, these vessels are used in aerospace applications hence the …

Microstructural Characterization And Oxidation Behavior Of Al-Cu-Ni-Mn And Al-Cu-Ni-Mn-Si Non-Body Centered Cubic High Entropy Alloys, Mckenna Mae Lin Hitter

Open Access Theses & Dissertations

High entropy alloys (HEA) differ from traditional alloying systems because five elements are mixed in equi-atomic proportions, as opposed to having one main principal element. As a result of exploring this new method of alloying, it was found that high entropy alloys demonstrate exceptional mechanical properties, an example being oxidation resistance, and are capable of enduring elevated temperatures. Seeing the potential that this new area of interest contains, studies involving a combination of elements to form various HEA have been performed. Most refractory metals are body-centered cubic and possess extremely high melting temperatures, so they are regularly considered when designing …

Analysis Of Drying Behavior Of Robocasted Barium Titanate, Abigail Ortega

Open Access Theses & Dissertations

Finding an adequate ceramic formulation for material extrusion is a time-consuming process. The necessary equipment may be unavailable to perform the desired test. This study demonstrated an alternative to observe a material after extrusion to understand its drying process. This study focused on 55 solid loading volume percent and a 39 solid loading volume percent, each with two different binder treatments focusing on fresh same day made binder, a 30 day old, aged binder and lastly an artificial binder obtained by a fuming process. Firstly, a formulation was created and loaded onto a pressure-based syringe to be extruded with a …

Improving Static Cold Storage Life Of The Human Heart Before Transplant, Juan Sebastian Rodriguez Paez

Theses and Dissertations

Organ storage and transportation are critical steps for the success of organ transplantation. Static cold storage (SCS) of hearts for heart transplantation (HTx) remains the standard approach. However, SCS may involve damage to the tissue resulting from extended hypothermic preservation, potentially affecting organ viability. More over, the temperature distribution on and within the heart is unknown during heart transplantation. Therefore, there is an interest to study different stages of the heart transplantation process towards determining the 3D temperature distribution on and within the heart. There could be a possibility of having a hypothermic injury in different parts of the heart …

Design And Application Of Smart Systems To Address Analytical Problems, Lucas B. Ayres

All Dissertations

This dissertation is a multidisciplinary effort that integrates low-cost analytical instrumentation, redox chemistry, and artificial intelligence to overcome existing limitations in the fields of wearable sensing technology, Deep Eutectic Solvents (DES), and antioxidant chemistry. The overall goal behind each implemented strategy is to enhance the accuracy, efficiency, and accessibility of analytical processes and technologies. A general overview of the thesis, along with the research outcomes is included in Chapter One. The theoretical framework of this dissertation is presented in Chapter Two. Chapter Three describes the development of a wearable platform (sensor and instrumentation) to rapidly detect (~20 minutes) S. aureus …

Boron-Doped Diamond As A Resilient Electrode Material In Molten Salts, Hannah Katherine Patenaude

UNLV Theses, Dissertations, Professional Papers, and Capstones

Molten salt chemistry has a range of applications within nuclear technology, including for the Molten Salt Reactors (MSRs) and pyroprocessing to recover valuable actinides for energy and national security needs. However, the high-temperature, corrosive nature of molten salts makes them particularly challenging to deploy on an industrial scale and study in benchtop measurements. Material accountability and corrosion monitoring of MSR fuels are essential components to the successful deployment of MSRs, and electroanalytical techniques like cyclic voltammetry (CV) and spectroelectrochemistry (SEC) can provide a wealth of information to describe salt systems in situ. To perform such measurements, it is imperative to …

A Manufacturing-To-Response Pathway For Manufacturing Optimization Of Carbon Fiber Reinforced Polymer Composite Structures, Madhura Limaye

All Dissertations

Over the past decade, there has been an increased adoption of thermoplastic and thermoset based continuous carbon fiber reinforced polymer (CFRP) composites for structural applications in several industries. Among the different manufacturing methods, thermoforming process for thermoplastic based continuous CFRP’s offer a major advantage in reducing cycle times for large scale productions. Similarly, out-of-autoclave curing process for thermoset based continuous CFRP’s using heated tooling enables production of large composite structures. However, these manufacturing processes can have a significant impact on the structural performance of parts by inducing undesirable effects. These effects include inhomogeneous fiber orientations, thickness variations, and residual stresses …

Enhanced Post Deposition Annealing Conditions On The Fabrication Of High Quality Thermochromic Vanadium Dioxide Films, Nuru R. Mlyuka

Tanzania Journal of Engineering and Technology (TJET)

Sputter deposition of thermochromic VO2 thin films for smart window applications has been faced with several challenges including the need for high deposition temperature, extremely precise and narrow range of oxygen/argon flow ratio and target poisoning during sputtering. Deposition of VO2 at room temperature without oxygen followed by post-deposition annealing has been cited as one of the potential mitigations to the challenge. In this study, the effects of post-deposition annealing conditions on the structural, electrical and optical properties of VO2 thin films are reported. The films were prepared on soda lime glass substrates using DC magnetron sputtering of metallic vanadium …

General Hydrogeochemical Characterization Of Groundwater In Coastal Aquifers Of Kilwa Kisiwani Oceanic Island, South East Tanzania, Simon R Melchioly

Tanzania Journal of Engineering and Technology (TJET)

The main objective of this study was to determine the hydrogeochemical processes controlling the groundwater chemistry on the Island and assess its suitability for human consumption and irrigation. The methodology used in the study include hydrogeological assessment of the study area and laboratory analysis for general physico-chemical parameters of groundwater. Other parameters such as Soluble sodium percentage (SSP) or % Na+, Sodium Adsorption Ratio (SAR), Magnesium adsorption ratio (MAR), Residual sodium carbonate (RSC), hydrochemical facies classification, and Water Quality Index (WQI) were calculated using empirical formulae. The effects of salinization of groundwater were classified using the chloride-Bicarbonate (Cl/HCO3) and the …

Optimization Pump As Turbine Coupled To A Self-Excited Induction Generator Using Multi-Objective Genetic Algorithm, Emanuel J. Nyirenda

Tanzania Journal of Engineering and Technology (TJET)

As a way of accelerating the deployment of affordable and clean renewable energy generation technologies, applying a pump working as a turbine coupled to a self-excited induction generator is gaining popularity in various areas including energy recovery and micro hydro systems. However, it is currently challenging to predict the performance of the PAT-SEIG system and there is no agreed-upon rule on the selection of the appropriate system to be installed at a particular site. This paper has presented multi-objective optimization to select the best operating point of the PAT-SEIG system. The results show that the peak efficiencies for the PAT …

Production Of Biofertilizer From Fruit And Garden Waste, Neema Msuya

Tanzania Journal of Engineering and Technology (TJET)

The project focused on the production of bio-fertilizer from fruit and garden waste, with a specific emphasis on utilizing pineapple tops in the composting process. The objective was to produce and assess the properties of the bio fertilizer obtained from this process and evaluate its potential application in agriculture. In this study, the composting process was done in a 0.7 m long, 0.85 wide and 1.1 m high vessel, and 0.238 m3 pineapple top wastes, resulting in 0.35 m3 of biofertilizer. The bio fertilizer produced exhibited favorable characteristics, including a moisture content of 36%, pH of 7.1, and a total …

Assessment Of Risk Factors Related To Body Pain Complaints In Tanzania Construction Industry, Fatma K. Mohamed

Tanzania Journal of Engineering and Technology (TJET)

The construction industry is associated with risks that can result in musculoskeletal diseases. Although young male workers who are presumed to be healthy dominate the industry in Tanzania, body pain complaints have been widely reported. The aim of this study is to assess the prevalence and causes of body pains in workers. A cross-sectional study involving 396 workers was conducted. A chi square test was used for testing association of independent categorical variables and binary logistic regression analysis was used to determine predictors for body pain complaints. The results show that all study participants complained of at least one form …