Engineering Science and Materials Commons^™

Variation Of Membrane Electrode Assembly Catalyst Layer In Unitized Regenerative Fuel Cell, Yollanda Nurcholifah, Dedi Rohendi, Edy Herianto Majlan, Nirwan Syarif, Addy Rachmat, Dwi Hawa Yulianti, Nyimas Febrika S

Journal of Electrochemistry

A unitized regenerative fuel cell (URFC) is a device that may function reversibly as either a fuel cell (FC) or water electrolysis (WE). An important component of this device is the Membrane electrode assembly (MEA). Therefore, this study aimed to compare the performance outcomes of MEA using electrodes with single and three catalyst layers. This study measured Electrochemical Surface Area (ECSA), Electrochemical Impedance Spectroscopy (EIS), X-ray Diffraction analysis (XRD), and X-ray Fluorescence (XRF). Furthermore, the round-trip efficiency (RTE) of the MEA, as well as the performance in FC and WE mode, was measured. In comparison, The ECSA values of Pt-Ru/C …

Innovative Design Methodology For Durable Open-Graded Friction Course Asphalt Mixtures, Anas Abualia

LSU Doctoral Dissertations

Open-graded friction course (OGFC) is a thin asphalt mixture surface layer with a high percentage of coarse aggregates and high interconnected air voids, which provides improved skid resistance, visibility, and decreased pavement-tire noise. However, construction personnel at DOTD reported that conventional OGFC mixtures have short service life (raveling distress). Further, their structural contribution to the pavement structure is commonly neglected and designed only for functionality purposes.

The objective of this study was to develop a rational mix design methodology to improve the durability of OGFC asphalt mixtures. Specific objectives are to: (1) conduct a rheological and chemical characterization of polymer-, …

Impulse, Spring 2025, Jill Fier, Micayla Standish, Jerome J. Lohr College Of Engineering

Impulse (Jerome J. Lohr College of Engineering Publication)

2 | Faculty, Staff Honored
4 | The State of Lithium
6 | 100 Years of Ag and Biosystems Engineering
8 | Major Milestones
12 | Distinguished Engineer Geldert-Murphy
14 | Distinguished Engineering Heitkamp
16 | By the Numbers
18 | Space Grant Consortium at SDSU
20 | Healthcare Systems Engineering Program
22 | Ridgway Three-Peat
23 | Aerospace Club Launches
24 | Power and Energy Scholarships
25 | More Take Part in Nasa Challenges
26 | Weber Recognized as Student Leader
30 | Wild Hare Racing Ready
32| Sebern’s Success as Sole Operator
34 | Meink: From Prairie to …

Observations Of Sea Ice Thermal Strain And Motion At Geophysically Relevant Scales, Larson M. Kaidel

Dartmouth College Ph.D Dissertations

Ongoing and unprecedented Arctic sea ice change as a result of anthropogenic climate change impacts life in the Arctic and beyond. The sea ice cover is becoming less expansive, thinner, younger, and more dynamic. Quantifying processes and properties that differ between old versus young and thick versus thin ice is central understanding the sea ice cover, improving climate change predictions, and developing strategies to adapt and mitigate the adverse effects of sea ice loss. Therefore, we seek to better understand how a key inherent ice property, the thermal strain coefficient, changes as ice types change, and observe how sea ice …

Approach Formula To Increase Energy Efficiency Of Internal Combustion Engines In The “Green Economy” And Impact On The Natural Ecosystem, Zakirjon Ergashevich Musabekov, Hilola Zokir Qizi Uralova, Sayyodbek Ilxomjon O‘G‘Li Abdullajonov

Technical science and innovation

This article discusses, analyzes, and proposes solutions for the role of internal combustion engines in forming a "green economy", as well as ways to replace or modernize them. The relationship between internal combustion engines and the "green economy," as well as their energy efficiency and impact on natural ecosystems, is a crucial and urgent issue. These engines primarily generate energy through the combustion of petroleum-based fuels such as gasoline and diesel. However, this process releases harmful gases into the atmosphere, contributing to environmental degradation. The green economy is an economic model designed to protect the environment, ensure the efficient management …

Recent Advances In Non-Enzymatic Electrochemical Sensors For Theophylline Detection, Gustria Ernis, Yulia M T A Putri, Muhammad Iqbal Syauqi, Prastika Krisma Jiwanti, Yeni Wahyuni Hartati, Takeshi Kondo, Qonita Kurnia Anjani, Jarnuzi Gunlazuardi

Journal of Electrochemistry

Detection of target analytes at low concentrations is significant in various fields, including pharmaceuticals, healthcare, and environmental protection. Theophylline (TP), a natural alkaloid used as a bronchodilator to treat respiratory disorders such as asthma, bronchitis, and emphysema, has a narrow therapeutic window with a safe plasma concentration ranging from 55.5–111.0 μmol·L^–1 in adults. Accurate monitoring of TP levels is essential because too low or too high can cause serious side effects. In this regard, non-enzymatic electrochemical sensors offer a practical solution with rapidity, portability, and high sensitivity. This article aims to provide a comprehensive review of the recent developments …

Study On Dopamine Electrochemical Sensing Based On Au@Mos2, Ning An, Ni Su, Xin-Ran Li, Jian-Yu Liu, Qi-Yan Wang

Journal of Electrochemistry

Dopamine (DA) is a vital neurotransmitter, and accurate detection of its concentration is critical for both clinical diagnostics and neuroscience research. Due to its electrochemical activity, DA is commonly detected using electrochemical methods, which are favored for their simplicity, fast response time, and suitability for in vivo analysis. In this work, a highly sensitive DA electrochemical sensor was developed using an Au@MoS₂ composite, created by modifying molybdenum disulfide (MoS₂) nanosheets with gold nanoparticles through HAuCl₄ reduction, and it was aimed at enhancing DA adsorption and improving detection performance. Scanning Electron Microscopy (SEM), transmission electron microscopy (TEM), …

In-Situ Electrodeposition Of Feco-Mof On Au Ultramicroelectrode For Highly Sensitive Detection Of Epinephrine, Yan Chen, Shang Jian, Si-Yu Wan, Xiao-Tong Cui, Zhong-Gang Liu, Zheng Guo

Journal of Electrochemistry

Metal-organic framework (MOF) nanostructures have emerged as a prominent class of materials in the advancement of electrochemical sensors. The rational design of bimetallic MOF-functionalized microelectrode is of importance for improving the electrochemical performance but still in great challenge. In this work, the bimetallic FeCo-MOF nanostructures were assembled onto a gold disk ultramicroelectrode (Au UME, 5.2 μm in diameter) via an in-situ electrodeposition method, which enhanced the sensitive detection of epinephrine (EP). The in-situ electrodeposited FeCo-MOF exhibited a characteristic nanoflower-like morphology and was uniformly dispersed on the Au UME. The FeCo-MOF/Au UME demonstrated excellent electrochemical performance on the detection of EP …

Preserve Your Hma Pavements From The Start, Tim Zahrn, Andrew Eicher

Purdue Road School

This presentation will review sustainable preservation treatments and their application timeline to extend the life of asphalt pavement. We will discuss how pre-preservation treatments like a void reducing asphalt membrane, early-life preservation treatments such as rapid penetrating emulsion, and topical rejuvenators can reduce future maintenance and delay reconstruction. We will also look at mid-life treatments, such as micro-surfacing, fit into a preventative maintenance preservation plan. And finally cover end of life cold pavement recycling alternatives.

Intelligent Turning Cyber-Physical Systems Modeling Using Sysml, Prithbey Raj Dey, David Lee Enke, Mario F. Buchely

Engineering Management and Systems Engineering Faculty Research & Creative Works

Cyber-Physical Systems (CPS) support industrial automation that incorporates people, hardware, signal, computation, and control using networking to achieve desired results. The complex automated CPS design demands a standard and comprehensive approach to appropriately identify the system requirements, define the architecture, and model the relationships among the software and hardware components. Systems Modeling Language (SysML) provides the capability for a comprehensive modeling to capture the desired design requirements in the systems architecture. SysML enables performance estimation of the model by analyzing constraints while identifying interactions among the components through various behavioral diagrams. In this paper, SysML is applied to the design …

Thermophysical Properties Of Aqueous Amine Salts For Closed Air Cabin Revitalization, Mahmud R. Yusuf, Isabela Flores, Ben Hines, Li Hua Zhang, Seth Christa, Brooks D. Rabideau, Kevin West, Breanna Dobyns, James Davis

Shelby Hall Graduate Research Forum Posters

Carbon dioxide (CO2) capture plays a crucial role in closed cabin air revitalization, however current CO2 capture technologies pose several issues. Traditional amine solutions, such as monoethanolamine, are commonly used in CO2 capture on the International Space Station but face drawbacks including high volatility, thermal degradation, and unpleasant odor. To overcome these challenges, amine salt solutions have emerged as promising alternatives. Amine salt solutions have reduced environmental impact, lower corrosion potential, and improved CO2 loading capacity, making them a more efficient and sustainable replacement. Knowing these physical properties are critical for modeling and optimizing a scrubbing process that employs these …

Treating Ground Water For Agricultural And Individual Consumption, Gabby Miller, Bronson Scott, Michael Clawson

Biomedical Engineering

This project, conducted in collaboration with Cal Poly seniors and Da Vinci High School students, aims to develop a solar-powered groundwater purification system. This system is designed to provide clean water for agricultural use and individual consumption, addressing the growing concerns of groundwater contamination and accessibility needs. The final prototype integrates a gravity filtration system combined with chemical purification, utilizing aluminum sulfate and chlorine to remove particulates, bacteria, and organic compounds.

The research phase involved an extensive review of groundwater contamination issues, existing filtration technologies, and market analysis. Key design constraints included cost-effectiveness, ease of maintenance, and minimal energy consumption, …

On The Exploration Of Crystallographic Anisotropy And Defects In Shock Loading Using Molecular Dynamics, Benjamin P. Helman

Theses and Dissertations

The impact of crystallographic orientation, grain boundaries, and vacancies on the shock behavior of aluminum was investigated using molecular dynamics simulations. Shock loading in the [001], [011], and [111] directions was explored, revealing anisotropic behavior in shock speed, melting, dislocation density, and unique phase changes. The Hugoniot elastic limit in the [100], [110], and [111] directions was calculated as 23.2 GPa, 24 GPa, and 18.4 GPa respectively. These results were found to be an order of magnitude larger than the compressive yield strength computed at equilibrium. Additionally, metastable melting in the [011] and [111] directions occurred roughly 1000 K below …

Discovering Design Requirements For Next Generation Arctic Tension Fabric Shelters, Mark W. Mcveigh

Theses and Dissertations

Military operations to remote Arctic regions require large-span temporary shelters to house tactical aircraft and provide heated maintained spaces. However, the current System-50 Large Area Maintenance Shelters used by the United States Air Force and Department of Defense are inadequate for Arctic deployments. These shelters lack durability against extreme subzero temperatures, heavy snow accumulation, and high wind speeds. They also fail to address critical Arctic-specific design challenges including permafrost protection, foundation disruption caused by frost heaves, and efficient heating as a result of their inadequate thermal resistance properties. This research analyzed 20 years of climatological data from 8,399 weather observation …

Fatigue Behavior Of Two Advanced C/Sic Composites At 1200°C In Air, Conner A. Adams

Theses and Dissertations

High-temperature tension-tension fatigue behavior of two advanced carbon/silicon carbide (C/SiC) ceramic matrix composites (CMCs) was investigated. Both composites were reinforced with T300 carbon fibers. Laminated carbon fiber preforms consisted of 24 plies of plain weave fabric in a 0/90 layup. The first composite, C/CVI-SiC, was processed by chemical vapor infiltration (CVI) of SiC into the fiber preform. Prior to the CVI process, the fiber preforms were coated with a duplex pyrolytic carbon and boron carbide fiber coating to create a weak fiber- matrix interphase. The second composite, C/HYPR-SiC, was also processed via CVI, but had an oxidation inhibited matrix comprising …

Fatigue Behavior Of An Advanced Sic/Sic Composite With An Array Of Small Cooling Holes At 1200°C, Tess K. Panchyshyn

Theses and Dissertations

Tension-tension fatigue behavior of an advanced melt-infiltrated (MI) silicon carbide/silicon carbide (SiC/SiC) composite was evaluated, and basic tensile properties measured, at 1200°C in laboratory air.  The composite consists of a melt-infiltrated SiC matrix reinforced with laminated Hi-Nicalon Type-S fibers woven in a 5-harness satin weave. The Hi-Nicalon-S fiber preforms were coated with a boron nitride (BN) fiber coating by chemical vapor infiltration (CVI). The melt-infiltrated matrix was consolidated by combining CVI-SiC with SiC particulate slurry and molten silicon infiltration. The finished ceramic matrix composite (CMC) had a fiber volume fraction of 33%. Additionally, the effect of multiple small holes on …

Improvement Of Microcracking And Mechanical Properties Of Tungsten Fabricated Via Laser Powder Bed Fusion Through Alloying With Reactive Secondary Constituents, William S. Mockel

Theses and Dissertations

Tungsten (W), a Group VI transition metal, possesses a number of advantageous properties, most notably its impressive mechanical performance at extreme temperatures. While tungsten's nature render traditional manufacturing methods difficult, additive manufacturing through laser powder bed fusion (LPBF) presents a promising avenue for fabricating tungsten components. However, the material’s high ductile-to-brittle transition temperature combined with the embrittling effect of impurities mean that the residual stresses imparted by LPBF result in microcracking in tungsten, degrading its usefulness. This study sought to improve the characteristics of LPBF-W through the removal of embrittling oxygen content via alloying with low concentrations of reactive elements, …

Mechanical Response Of Triply Periodic Minimal Surface Gyroid Structures Under Combined Loading, Jay B. Patel

Theses and Dissertations

This work explored combined tensile and torsional loads applied to additively manufactured Inconel 718 specimens employing Triply Periodic Minimal Surface (TPMS) structures. The gyroid TPMS unit cell was selected with two variations of cylindrical cell maps, a rectangular cell map, and a spherical cell map. All four variants were tested in an axial-torsion test frame at room temperature using equal parts of vertical and angular displacement control until failure. The combined loading in these tests utilized tension and torsion. The data from the tests were compared to finite element analysis (FEA) models to visualize when yielding was predicted. Finally, the …

Metal Nitrides As Cathode Hosts For Lithium-Sulfur Batteries, Hai-Ji Xiong, Cheng-Wei Zhu, Ding-Rong Deng, Qi-Hui Wu

Journal of Electrochemistry

Lithium-sulfur batteries are considered as one of the potential solutions as integrating renewable energy systems for large-scale energy storage because of their high theoretical energy density (2600 Wh·kg^–1) and specific capacity (1675 mAh·g^–1). Currently, various strategies have been proposed to overcome the technical barriers, e.g., “shuttle effect”, capacity decay and volumetric change, which impede the successful commercialization of lithium-sulfur batteries. This paper reviews the applications of metal nitrides as the cathode hosts for high-performance lithium-sulfur batteries, summarizes the design strategies of different host materials, and discusses the relationship between the properties of metal nitrides and their …

Sno2 Particles Embedded Into Carbon Coated Mesoporous SioX Rod As High Volumetric Capacity Anode For Lithium-Ion Batteries, Jia-Lin Guo, Ni-Ni Li, Peng Zheng

Journal of Electrochemistry

Due to the high capacity and moderate volume expansion of silicon protoxide SiO_x (160%) compared with that of Si (300%), reducing silicon dioxide SiO₂ into SiO_x while maintaining its special nano-morphology makes it attractive as an anode of Li-ion batteries. Herein, through a one-pot facile high-temperature annealing route, using SBA15 as the silicon source, and embedding tin dioxide SnO₂ particles into carbon coated SiO_x, the mesoporous SiO_x-SnO₂@C rod composite was prepared and tested as the anode material. The results revealed that the SnO₂ particles were distributed uniformly in the …