Engineering Science and Materials Commons^™

Molecular Modeling Of Epon 862-Detda Polymer , Ananyo Bandyopadhyay

Dissertations, Master's Theses and Master's Reports - Open

EPON 862 is an epoxy resin which is cured with the hardening agent DETDA to form a crosslinked epoxy polymer and is used as a component in modern aircraft structures. These crosslinked polymers are often exposed to prolonged periods of temperatures below glass transition range which cause physical aging to occur. Because physical aging can compromise the performance of epoxies and their composites and because experimental techniques cannot provide all of the necessary physical insight that is needed to fully understand physical aging, efficient computational approaches to predict the effects of physical aging on thermo-mechanical properties are needed. In this …

A Basic Understanding Of Rapid Mold Surface Heating Via Laser Energy, Charles Daniel Fox

Browse all Theses and Dissertations

As the research and development of surface heating methods have increased in the recent years, the consensus has been reached amongst the injection molding community that an elevated mold surface temperature near or greater than the polymer solidification temperature provides acceptable replication of the desired micro-structured parts. The laser heating experimental work and simulation development carried out includes two sample sizes similar to those used in injection molding. A 100W CO2 laser incident on three samples of different surface roughnesses has shown to have elevated temperatures via thermal cameral data and thermocouple measurements. Among five different laser spot sizes varying …

Key Factors Influencing The Structure And Electrochemical Performances Of Lifepo4 Via Sol-Gel Synthesis, Chuang Guan

Browse all Theses and Dissertations

Olivine structured LiFePO4 is a promising cathode material for the next generation of lithium ion batteries for its low cost, environmental benign, good cycling performance and safety, etc. However, its intrinsic poor electrical conductivity and diffusion capability of lithium ion greatly hinder its application in the high power recharge battery. In this research, a cost-effective sol-gel method was used to synthesize carbon coated LiFePO4 (LiFePO4/C) materials. The influences of the synthesis parameters, including the species of iron source, lithium content, chelating agents and carbon sources, PH value of the sol, and sintering conditions etc., on the structure and electrochemical properties …

Isothermal Deformation And Modeling Of Ti-6al-4v, Vamsi Krishna Vempati

Browse all Theses and Dissertations

Ti-6Al-4V has attractive properties such as high strength to weight ratio, good fatigue properties and excellent corrosion resistance and these properties have made this alloy an important material for the aerospace industry. In this thesis, the deformation behavior of Ti-6Al-4V with several processing histories, was studied by conducting isothermal constant strain rate compression tests over a temperature range of 829°C to 996°C (1525°F to 1825°F) and at strain rates of 10-2 s-1, 10-1 s-1 and 100 s-1. True stress versus true strain flow curves showed a peak stress followed by flow softening. The data was analyzed to obtain constitutive equations …

Modeling The Exfoliation Rate Of Graphene Nanoplatelet Production And Application For Hydrogen Storage, Cory Knick

Browse all Theses and Dissertations

Graphene is a unique and revolutionary new nanomaterial. A method for it's production had a U.S. patent application in 2002 (patent issued in 2006), it was produced via mechanical exfolia-tion in 2004, and subsequently the Nobel Prize in Physics was awarded in 2010 for it. These events have sparked a surge of graphene-related research. In order for graphene to be widely studied and incorporated into emerging technologies, a versatile method for large scale produc-tion of high-quality graphene is required. Current methods are either slow or expensive which limits the scale-up of graphene production. Very recently, the liquid phase exfoliation of …

Coupled Electromagnetic And Heat Transfer Model For Microwave Heating In Domestic Ovens, Krishnamoorthy Pitchai, Sohan Birla, Jeyamkondan Subbiah, D. D. Jones, Harshanardhan Thippareddi

Department of Food Science and Technology: Faculty Publications

Microwave ovens are used extensively for heating a variety of not-ready-to-eat food products. Non-uniform heating of foods in microwave ovens is a major concern in assuring microbiological safety of such products. The non-uniform heating of foods is attributed by complex interaction of microwaves with foods. To understand this complex interaction, a comprehensive model was developed to solve coupled electromagnetic and heat transfer equations using finite-difference time-domain based commercial software. The simulation parameters, cell size, heating time step, and number of iterations for steady state electromagnetic field were optimized. The model was validated by 30 s heating profile of a cylindrical …

Moisture Damage Characterization Of Warm-Mix Asphalt Mixtures Based On Laboratory-Field Evaluation, Yong-Rak Kim, Jun Zhang, Hoki Ban

Department of Mechanical and Materials Engineering: Faculty Publications

This study presents laboratory evaluation integrated with field performance to examine two widely used warm-mix asphalt (WMA) approaches—foaming and emulsion technology. For a more realistic evaluation of the WMA approaches, trial pavement sections of the WMA mixtures and their counterpart hot-mix asphalt (HMA) mixtures were implemented in Antelope County, Nebraska. Field-mixed loose mixtures collected at the time of paving were transported to the laboratories to conduct various experimental evaluations of the individual mixtures. Among the laboratory tests, three (two conventional and one newly attempted) were performed to characterize moisture damage potential which is the primary focus of this study. From …

Monitoring The Wall Mechanics During Stent Deployment In A Vessel, Brian Steinert, Shijia Zhao, Linxia Gu

Department of Mechanical and Materials Engineering: Faculty Publications

Clinical trials have reported different restenosis rates for various stent designs . It is speculated that stentinduced strain concentrations on the arterial wall lead to tissue injury, which initiates restenosis . This hypothesis needs further investigations including better quantifications of non-uniform strain distribution on the artery following stent implantation. A non-contact surface strain measurement method for the stented artery is presented in this work. ARAMIS stereo optical surface strain measurement system uses two optical high speed cameras to capture the motion of each reference point, and resolve three dimensional strains over the deforming surface. As a mesh stent is deployed …

Thickness-Shear And Thickness-Twist Modes In An Oblate Elliptical Ceramic Cylinder And Energy Trapping In Contoured Acoustic Wave Resonators, Huijing He, Jiashi Yang, Yi-Hua Huang

Department of Mechanical and Materials Engineering: Faculty Publications

We study shear-horizontal motions of a piezoelectric ceramic cylinder with an oblate elliptical cross section and axial poling. Exact thickness-shear and thickness-twist vibration modes are obtained. These modes show energy trapping, i.e., the vibration is mainly confined near the thick, central region and decays to almost nothing near the edges. The results are useful for the understanding and design of contoured piezoelectric resonators for strong energy trapping.

Systems And Synthetic Biology Of The Vessel Wall, Jennifer Frueh, Nataly Maimari, Ying Lui, Zoltan Kis, Vikram Mehta, Negin Pormehr, Calum Grant, Emmanuel Chalkias, Mika Falck-Hansen, Sandra Bovens, Ryan M. Pedrigi, Taka Homma, Gianfillippo Coppola, Rob Krams

Department of Mechanical and Materials Engineering: Faculty Publications

Atherosclerosis is intimately coupled to blood flow by the presence of predilection sites. The coupling is through mechanotransduction of endothelial cells and approximately 2000 gene are associated with this process. This paper describes a new platform to study and identify new signalling pathways in endothelial cells covering an atherosclerotic plaque. The identified networks are synthesized in primary cells to study their reaction to flow. This synthetic approach might lead to new insights and drug targets.

Nanotopographic Cell Culture Substrate: Polymer-Demixed Nanotextured Films Under Cell Culture Conditions, Jung Yul Lim, Christopher A. Siedlecki, Henry J. Donahue

Department of Mechanical and Materials Engineering: Faculty Publications

Modulating physical cell culture environments via nanoscale substrate topographic modification has recently been of significant interest in regenerative medicine. Many studies have utilized a polymer-demixing technique to produce nanotextured films and showed that cellular adhesion, proliferation, and differentiation could be regulated by the shape and scale of the polymer-demixed nanotopographies. However, little attention has been paid to the topographic fidelity of the polymer-demixed films when exposed to cell culture conditions. In this brief article, two polymer-demixing systems were employed to assess topographic changes in polymer-demixed films after fibronectin (FN) extracellular matrix protein adsorption and after incubation in phosphate-buffered saline at …

Usability Assessment Of Two Different Control Modes For The Master Console Of A Laparoscopic Surgical Robot, Xiaoli Zhang, Carl A. Nelson, Dmitry Oleynikov

Department of Mechanical and Materials Engineering: Faculty Publications

The objective of this study is to evaluate potential interface control modes for a compact fourdegree- of-freedom (4-DOF) surgical robot. The goal is to improve robot usability by incorporating a sophisticated haptics-capable interface. Two control modes were developed using a commercially available haptic joystick: (1) a virtually point-constrained interface providing an analog for constrained laparoscopic motion (3-DOF rotation and 1-DOF translation), and (2) an unconstrained Cartesian input interface mapping more directly to the surgical tool tip motions. Subjects (n = 5) successfully performed tissue identification and manipulation tasks in an animal model in point-constrained and unconstrained control modes, respectively, with …

Tool Sequence Trends In Minimally Invasive Surgery: Statistical Analysis And Implications For Predictive Control Of Multifunction Instruments, Carl A. Nelson, Evan Luxon, Dmitry Oleynikov

Department of Mechanical and Materials Engineering: Faculty Publications

This paper presents an analysis of 67 minimally invasive surgical procedures covering 11 different procedure types to determine patterns of tool use. A new graph-theoretic approach was taken to organize and analyze the data. Through grouping surgeries by type, trends of common tool changes were identified. Using the concept of signal/noise ratio, these trends were found to be statistically strong. The tool-use trends were used to generate tool placement patterns for modular (multi-tool, cartridge-type) surgical tool systems, and the same 67 surgeries were numerically simulated to determine the optimality of these tool arrangements. The results indicate that aggregated tool-use data …

Feasibility Analysis Of Estrification Systems With Entrainers, Kang Wook Lee

Dissertations and Theses

(Ethyl Acetate) and IPA (Isopropyl Acetate) production systems are studied in terms of the feasibility analysis. It is not feasible to retrieve pure products by a simple reactive distillation for IPA production system because CCR (Critical Composition Region) covers the entire desired binary edge for IPA system. On the other hand, even though CCR does not cover the entire desired binary edge of the EA system completely, internal reflux ratio (IRR) analysis does not allow the production of the pure product via reactive distillation for EA production system. To overcome the restraints, external entrainers are utilized to take advantage of …

Microwave-Assisted Wet Chemical (Mawc) Synthesis Of Lithium Iron Phosphate, Shangzhao Shi

Dissertations, Master's Theses and Master's Reports - Open

LiFePO4 is a Co-free battery material. Its advantages of low cost, non-toxic and flat discharge plateau show promising for vehicle propulsion applications. A major problem associated with this material is its low electrical conductivity. Use of nanosized LiFePO4 coated with carbon is considered a solution because the nanosized particles have much shorter path for L+ ions to travel from the LiFePO4 crystal lattice to electrolytes. As other nano material powders, however, nano LiFePO4 could have processing and health issues.

In order to achieve high electrical conductivity while maintaining a satisfactory manufacturability, the particles should possess both of the nano- and …

Finite Element Analysis Of The Contact Deformation Of Piezoelectric Materials, Ming Liu

Theses and Dissertations--Chemical and Materials Engineering

Piezoelectric materials in the forms of both bulk and thin-film have been widely used as actuators and sensors due to their electromechanical coupling. The characterization of piezoelectric materials plays an important role in determining device performance and reliability. Instrumented indentation is a promising method for probing mechanical as well as electrical properties of piezoelectric materials.

The use of instrumented indentation to characterize the properties of piezoelectric materials requires analytical relations. Finite element methods are used to analyze the indentation of piezoelectric materials under different mechanical and electrical boundary conditions.

For indentation of a piezoelectric half space, a three-dimensional finite element …

High Pressure Synchrotron X-Ray Diffraction Studies Of Superprotonic Transitions In Phosphate Based Solid Acids, Juan Daniel Hermosillo

Open Access Theses & Dissertations

Certain phosphate based solid acids, such as CsH2PO4 and RbH2PO4, have been shown to exhibit an abrupt, several-order-of-magnitude increase in their proton conductivity when heated above a temperature threshold. This so called superprotonic behavior allows the above-mentioned materials to function as fuel cell electrolytes at temperatures between 150C and 300C, a remarkable application that attracted significant interest especially from the automobile industry. Yet, the microscopic structures and dynamic mechanisms responsible for this behavior are not fully understood. In fact, until very recently, the very nature of the superprotonic behavior has been debate, with some groups attributing the steep proton enhancement …

Development Of Nanocomposites For Energy Storage Devices, Md Ashiqur Rahaman Khan

Open Access Theses & Dissertations

With the ever-increasing need in improving the performance and operation life of future mobile devices, developing higher power density energy storage devices has been receiving more attention. Lithium ion battery (LIB) and capacitor are two of the most widely used energy storage devices and have attracted increasing interest from both industrial and academic fields. Batteries have higher power density than capacitor but significantly longer charge/discharge rates. In order to further improve the performance of these energy storage devices, one of the approaches is to use high specific surface area nano-materials. Among all the nano-materials developed so far, one-dimensional nanowires are …

Thin Film Growths Of Znte And Cdte On Various Substrates Using A Novel Close Space Sublimation Reactor Css4, Damian Marrufo

Open Access Theses & Dissertations

Thin films of CdTe have been grown on CdS in a variety of methods for use in thin film photovoltaic systems. Limits to the efficiency of CdTe/CdS solar cells have been attributed to defects in the lattice that occur between the interface of CdS and CdTe due to a lattice mismatch. A close space sublimation (CSS) reactor known as the CSS4 was designed and fabricated in UTEP to deposit complex layers of CdTe and ZnTe on top of a CdS film that is grown via chemical bath deposition in order to obtain a CdTe photovoltaic. Unfortunately, the original design and …

Nanoprobe I-V Characterization Of Cdte/Cds Micro And Nano-Patterned Solar Cells, Heber Prieto

Open Access Theses & Dissertations

This thesis presents a novel way to characterize micro and nano patterned cadmium telluride thin film solar cells via a nano-probe system. A historical review of CdTe-based solar cells is presented first followed by review of the technology developed to produce the patterned CdTe cells. A detailed presentation is then provided on the use of a Zyvex nanoprobing system to characterize the patterned solar cells. The I-V response of micro- and nano-patterned solar cells stimulated under different e-beam conditions is presented and analyzed. Suggestions of how to improve the technique are provided. This work documents, for the first time, the …