Creating Blood Analogs To Mimic Steady-State Non-Newtonian Shear-Thinning Characteristics Under Various Thermal Conditions,
2025
Wright State University
Creating Blood Analogs To Mimic Steady-State Non-Newtonian Shear-Thinning Characteristics Under Various Thermal Conditions, Hang Yi, Alexander Wang, Christopher Wang, Jared Chong, Chungyiu Ma, Luke Bramlage, Bryan Ludwig, Zifeng Yang
Mechanical and Materials Engineering Faculty Publications
Blood analogs are widely employed in in vitro experiments such as particle image velocity (PIV) to secure hemodynamics, assisting pathophysiological diagnoses of neurovascular and cardiovascular diseases, as well as pre-surgical planning and intraoperative orientation. To obtain accurate physical parameters, which are critical for diagnosis and treatment, blood analogs should exhibit realistic non-Newtonian shear-thinning features. In this study, two types of blood analogs working under room temperature (293.15 K) were created to mimic the steady-state shear-thinning features of blood over a temperature range of 295 to 312 K and a shear range of 1~250 s−1 at a hematocrit of ~40%. Type …
Electron Beam Irradiation Effects On Bulk Metals And High Entropy Alloys (Crmnv And Crmntiv) And The Synthesis And Characterization Of Irradiation-Induced Damage In Polycrystalline Metal And High Entropy Alloy Thin Films,
2025
Old Dominion University
Electron Beam Irradiation Effects On Bulk Metals And High Entropy Alloys (Crmnv And Crmntiv) And The Synthesis And Characterization Of Irradiation-Induced Damage In Polycrystalline Metal And High Entropy Alloy Thin Films, Najmin Ara Sultana
Mechanical & Aerospace Engineering Theses & Dissertations
Accelerator beam exit windows are designed to withstand intense radiation and mechanical stress while preserving beam transmission and structural integrity. This dissertation explores the structural and mechanical responses of pure metals and high-entropy alloys (HEAs), in both bulk and thin-film forms, under high-dose electron beam (e-beam) irradiation to identify optimal materials for next-generation accelerator exit windows. Monte Carlo simulations using FLUKA, conducted at Jefferson Lab, revealed that amongst Ni, Ti, Cr, and V, Ni exhibits the highest power dissipation, while Ti depicts the lowest power dissipation, with Cr and V demonstrating intermediate characteristics. Bulk polycrystalline (PC) and single-crystalline (SC) samples …
Investing Hysteresis In Floodplain Dynamics Of Lakes In The Middle St. Johns River Using Sentinel-1 Sar Imagery,
2025
Embry-Riddle Aeronautical University
Investing Hysteresis In Floodplain Dynamics Of Lakes In The Middle St. Johns River Using Sentinel-1 Sar Imagery, Keenan Hubbard
Doctoral Dissertations and Master's Theses
Floodplain dynamics are often complex, with hysteresis potentially affecting the temporal relationship between flood stage and flood extent during subsequent inundation phases. This study leverages Sentinel-1 synthetic aperture radar (SAR) imagery to map flood extent in the Middle St. Johns River Lake floodplains and examine the presence of hysteresis during flood events. SAR scenes corresponding to river gauge readings were analyzed from the rising and falling limbs of a flood hydrograph. By comparing these flood maps, we assess differences in inundated areas at equivalent water levels during each stage of the flood event. The findings aim to enhance flood monitoring …
Mno2 Nanoscale Interface Modification,
2025
Embry-Riddle Aeronautical University
Mno2 Nanoscale Interface Modification, Alexander C. Skoppe
Doctoral Dissertations and Master's Theses
Interface modification of carbon fibers has been shown to improve the mechanical performance of composites. In addition, interface modification of carbon fiber composites can impart multifunctionality into the resulting composite. This work will explore ZnO and MnO2 as interface modifications for use on carbon fibers. When exposed to high temperatures, carbon fibers undergo fiber degradation, leading to the need for low-temperature hydrothermal processes. This work will develop and characterize a nanoscale ZnO and MnO2 interface modification for use on carbon fibers. These nanomodifications will be developed with low-temperature processes, minimizing the fiber degradation that the fibers undergo. Fourier transform infrared …
Advanced Study Of Nickel-Titanium Alloy: Effects Of Point Defects On Mechanical And Thermodynamic Properties,
2025
University of Texas at El Paso
Advanced Study Of Nickel-Titanium Alloy: Effects Of Point Defects On Mechanical And Thermodynamic Properties, Diego Armando Juarez Rosales
Open Access Theses & Dissertations
High-throughput first-principles calculations of point defects are emerging as a powerful tool to accelerate materials discovery in applications [1]. Substitutional, antisite, and vacancy defects can play an important role in the mechanical and thermal properties of intermetallic alloys [2]. In this present work I compute the thermal and mechanical properties of shape-memory alloy nickel-titaniun (NiTi) in the B19â?? martensitic and B2 austenitic phases from molecular dynamics (MD), using a second nearest neighbor (2NN) modified embedded atom method (MEAM) [3] classical potential in the temperature range from 200K to 600K and composition range from 45 atomic percent to 55 atomic percent …
The Utilization Of Basic Oxygen Furnace Slag As Fine Aggregates In Concrete: Physical, Mechanical, And Durability Properties,
2025
Betâo Liz SA, Avenida Almirante Gago Coutinho, Portela 2710-418 Sintra, Portugal
The Utilization Of Basic Oxygen Furnace Slag As Fine Aggregates In Concrete: Physical, Mechanical, And Durability Properties, Hakan Ozkan
Journal of Sustainable Construction Materials and Technologies
This study examines the feasibility of using basic oxygen furnace slag (BOFS) as an alternative to fine crushed limestone aggregate in concrete. BOFS is sourced from two steel production facilities in Türkiye, designated as I-BOFS and E-BOFS. The experimental results showed that as the E-BOFS aggregate replacement ratio increased, the water-to-cement (w/c) ratio increased to maintain the target workability. The concrete mixtures incorporating E-BOFS exhibited consistent reductions in the compressive strength with an increase in the BOFS ratio. At the same time, I-BOFS maintained higher compressive strength, with only minor losses up to 80% of the substitution ratio. Flexural strength …
Development Of A Self-Cured Alkali-Activated Mortar,
2025
Department of Architecture, Faculty of Architecture and Design, Kocaeli University, 41300 Kocaeli, Türkiye
Development Of A Self-Cured Alkali-Activated Mortar, Kübra Ekiz Barış
Journal of Sustainable Construction Materials and Technologies
Alkali-activated mortars (AAM) can be produced with self-curing (SC), which supplies internal moisture to accelerate alkaline-activation reactions. The aim of using SC is to make AAMs with an early-age strength without any additional curing energy consumption and higher CO2 emissions, and to obtain in-situ practical advantages that enable the large-scale application of AAMs. The previous study produced natural pozzolan-based AAMs by applying energy-intensive heat (HC), microwave (MWC), and hybrid (HC+MWC) curing. This study investigates alternative curing regimes that reduce production energy without compromising material properties. The impacts of air curing (AC), water curing (WC), and SC on the properties were …
Naoh Molarity Effect On Mechanical And Hydrochloric Acid Resistance Of Geopolymer Mortar Based On Slag,
2025
Department of Civil Engineering, Istanbul Aydin University, Istanbul, Türkiye
Naoh Molarity Effect On Mechanical And Hydrochloric Acid Resistance Of Geopolymer Mortar Based On Slag, Mahmoud Ziada, Zahraa Mohammed Kamil Al-Mayali
Journal of Sustainable Construction Materials and Technologies
The present research investigates the influence of different sodium hydroxide (NaOH) molarities on the mechanical characteristics and hydrochloric acid (HCl) resistance of geopolymer grouts manufactured from ground granulated blast-furnace slag (GGBS). Geopolymer mortars have attracted interest as sustainable substitutes for traditional cementitious materials due to their advantageous environmental effects and enhanced durability features. This study involved the fabrication of geopolymer mortar specimens by altering the NaOH molarity (M) from 6 M to 14 M. The mechanical and physical qualities were assessed using compressive strength, capillary water absorption, flexural strength, slump flow, and ultrasonic pulse velocity (UPV) tests. Subsequently, the geopolymer …
Effect Of Expanded Perlite And Exfoliated Vermiculite Aggregate Additives On Water Vapor Permeability Performance Of Cement-Based Lightweight Mortars,
2025
İzmir Katip Çelebi University, Department of Civil Engineering, 35620, İzmir, Türkiye
Effect Of Expanded Perlite And Exfoliated Vermiculite Aggregate Additives On Water Vapor Permeability Performance Of Cement-Based Lightweight Mortars, Lütfullah Gündüz, Şevket Onur Kalkan
Journal of Sustainable Construction Materials and Technologies
Vapor diffusion is the movement of water vapor molecules through porous materials such as wood, insulation products, and lightweight wall elements due to differences in vapor pressure. Vapor retarders are used to control vapor diffusion through wall sections and surfaces. All building materials provide some resistance to vapor diffusion, and the amount of resistance varies depending on the material's properties. These properties can vary with relative humidity and moisture content, age, temperature, and other factors. Vapor resistance is usually expressed using the inverse term of ``vapor permeability,'' which is the relative ease of vapor diffusion through a material. Water vapor …
Rubber-Modified Self-Compacting Mortar: Evaluating Setting Time And Strength Development,
2025
Department of Civil Engineering, Gaziantep University, 27310, Gaziantep, Türkiye
Rubber-Modified Self-Compacting Mortar: Evaluating Setting Time And Strength Development, Navvar Makansi, Süleyman Ipek, Erhan Güneyisi
Journal of Sustainable Construction Materials and Technologies
The influence of using crumb rubber (CR) obtained from the second scraping of used tires as fine aggregate in manufacturing self-compacting mortar (SCM) was investigated experimentally in this study. To explore this, natural fine aggregate in SCM mixes was partially replaced with CR at levels ranging from 5% to 25% by total fine aggregate volume. Two mix series, one with a total binder of 500 kg/m3 and the other with a 540 kg/m3 binder, were designed at water-to-binder ratios of 0.40 and 0.33. Ordinary Portland cement (80% by weight) and fly ash (20% by weight) were used to manufacture mortars. …
Smart Traffic Management At Intersections,
2025
Department of Traffic and Transport, Faculty of Mechanical Engineering, University of Pristina, Pristina, Kosovo
Smart Traffic Management At Intersections, Gezim Hoxha, Piotr Gorzelanczyk, Rame Likaj, Shaban Thaqi, Flori Cikaqi
Journal of Sustainable Construction Materials and Technologies
Effective traffic control methods, whether at intersections or other nodes within the road network, play a critical role in ensuring traffic quality and safety. An inappropriate choice of traffic control techniques or poorly optimized light signal programming at intersections often leads to unsatisfactory service levels. This study specifically addresses the issues related to intersections controlled by traffic lights. It aims to identify the key factors influencing the regulation and programming of traffic lights, with a focus on using different microcontrollers, particularly the Raspberry Pi. The primary objective of this research is to develop a methodology and an adapted programming approach …
Identification Of Barriers And Drivers In The Adoption Of Sustainable Construction Practices In The Turkish Construction Industry: Exploratory Factor Analysis,
2025
Balikesir University, Faculty of Architecture, Çağış Campus, Balikesir, Türkiye
Identification Of Barriers And Drivers In The Adoption Of Sustainable Construction Practices In The Turkish Construction Industry: Exploratory Factor Analysis, Tülay Çivici, Mustafa Serhan Ünlütürk
Journal of Sustainable Construction Materials and Technologies
Although the importance of sustainability in the construction industry has been emphasised by many researchers and endorsed by many authorities, it is clear that the practices in the industry still need to be improved. The primary issue for adopting sustainable practices in the construction industry is identifying the barriers and drivers. For this reason, the study analysed the literature to identify the critical barriers and incentives for adopting sustainable practices in the construction industry. In light of the information from the literature, the necessary barriers and motivators in adopting sustainable practices in the construction industry were determined, and a questionnaire …
Synergistic Effect Of Alccofine As Partial Replacement Of Cement And M-Sand As Sand Substitution In Concrete For The Assessment Of Mechanical And Microstructural Properties,
2025
Research Scholar, Department of Civil & Structural Engineering, Annamalai University, Chidambaram-608001, Tamil Nadu, India
Synergistic Effect Of Alccofine As Partial Replacement Of Cement And M-Sand As Sand Substitution In Concrete For The Assessment Of Mechanical And Microstructural Properties, Yellinedi Madhavi, R.S. Ravichandran, J. Saravanan, N. Venkatasairam Kumar
Journal of Sustainable Construction Materials and Technologies
Using supplementary cementitious materials (SCMs) and traditional binder mass has revolutionized concrete production technology in the building industry. This study examines how Alcofine-1203 affects the microstructure and mechanical characteristics of concrete. The mechanical qualities of the mixtures were evaluated using six different mixes prepared for each M25 and M40 Grade. In the proposed mixes, cement is substituted with alccofine at 0 to 25% and M-Sand as fine aggregate. The Compressive strength and ultrasonic pulse velocity were assessed after 3, 7, 14, 28, 56, and 90 days of curing, and split tensile strength and flexure strength were evaluated after 28 and …
Sustainable Modification Of Stone Column Technique With Polyethylene Terephthalate (Pet) Plastic For Strengthening The Expansive Clay,
2025
Department of Civil Engineering, Faculty of Civil Engineering Technology, Universiti Malaysia Pahang Al-Sultan Abdullah, Lebuhraya Tun Razak 26300 Kuantan, Pahang Darul Makmur, Malaysia
Sustainable Modification Of Stone Column Technique With Polyethylene Terephthalate (Pet) Plastic For Strengthening The Expansive Clay, Ng Jun Shen, Muzamir Hasan
Journal of Sustainable Construction Materials and Technologies
This research investigated the modification of stone column application by the association of PET plastic as a coarse aggregate material for sustainable material replacement. Clay soil improvement with a granular material fabricated column substantially affected its soil-bearing capacity. Subsequently, it avoided severe problems such as soil settlement and structural instability. Previous studies have mentioned the function and alteration of stone columns using materials like bottom ash and fly ash. Still, no attention has been paid to the utilization of PET plastic for this area. This study examined the feasibility and reliability of materials, PET plastic, and kaolin clay S300 before …
Effect Of Reinforcement Thickness And Content On The Properties Of Compressed Earth Blocks,
2025
Department of Civil Engineering, ARCHIPEL Laboratory, University of Tahri Mohmed, Bechar 08000, Algeria
Effect Of Reinforcement Thickness And Content On The Properties Of Compressed Earth Blocks, Salah Eddine Mokeddem, Abdelmadjid Hamouine, Rabia Abdeldjebar, Atef Hamaidi
Journal of Sustainable Construction Materials and Technologies
This study explores the mechanical, hygroscopic, and thermal behavior of stabilized and unstabilized compressed earth blocks (CEB) by incorporating date palm wood chips (DPWC) as a natural fiber additive. The investigation covers a range of DPWC thicknesses (1 mm, 2 mm, 3 mm) and content variations (0% to 1% by weight), focusing on the interaction between the bio-based reinforcement and the stabilized soil matrix, which is stabilized with 10% white Portland cement. The mixtures were compressed at a pressure of 5 MPa using a hydraulic press, providing a detailed examination of how these parameters impact the structural integrity and functional …
Energy Optimal Coverage Motion Trajectory Generation Using A Fourth-Order Motion Profile,
2025
Department of Mechanical and Industrial Engineering, University of Dar es Salaam, P.O Box 35131, Dar es Salaam, Tanzania
Energy Optimal Coverage Motion Trajectory Generation Using A Fourth-Order Motion Profile, Mathias Halinga
Tanzania Journal of Engineering and Technology (TJET)
Industrial machines are widely used in manufacturing sector to manufacture several products to meet customer demands. Most of these industries runs all the time throughout a day leading to high operating cost. To cut costs and satisfy customer demand for precise products, industrial machines’ motion generation is important in improving machine motion precision while using less energy. This study presents a coverage motion energy optimization which is generated by linear interpolation of each segment described by the fourth-order motion profile. The phase changes in the profile are attained with continuity of machine kinematic limits jerk, acceleration, and velocity, which are …
Calibration Of Measurement Tools In The Experimental Test Rig For Hydropower Performance Evaluation,
2025
Department of Energy and Petroleum Engineering, University of Dodoma, P. O. Box 259, Dodoma, Tanzania.
Calibration Of Measurement Tools In The Experimental Test Rig For Hydropower Performance Evaluation, Ombeni J. Mdee
Tanzania Journal of Engineering and Technology (TJET)
The demonstration of a typical hydropower plant requires the development of a test rig with the installation of tools to measure the performance parameters. The measurement tools require a calibration process to improve the quality of recorded data. This study involved the calibration of traditional and automated measurement tools connected to the hydropower test rig through an Arduino microprocessor. The automated measurement tools included a pressure transducer, flow meter, digital tachometer, and torque transducer, while traditional measurement tools, including a pressure gauge, concrete water tank, contact tachometer, and force lever arm balance, were connected in the same test rig during …
Data-Driven Constrained Control,
2025
University of New Mexico
Data-Driven Constrained Control, Ali Kashani
Mechanical Engineering ETDs
Ensuring safety is a fundamental challenge. Traditional methods often rely on precise mathematical models, which are difficult, impractical, or costly to obtain for real-world systems with complex, nonlinear dynamics. This dissertation develops direct data-driven control approaches that enable safe and efficient operation of nonlinear systems without requiring explicit models or performing system identification. This effort leverages machine learning, optimization, and control theory to bridge theoretical rigor and practical applicability. Deterministic guarantees are provided based on the Lipschitz continuity of the system, and probabilistic guarantees through scenario optimization. The computation of safe sets is performed using one-shot approaches with broad neural …
Towards Metrology 4.0 In Developing Countries’ Manufacturing Industries,
2025
Department of Legal and Industrial Metrology, College of Business Education, P.O Box 1968 Dar es Salaam, Tanzania
Towards Metrology 4.0 In Developing Countries’ Manufacturing Industries, Jailos Nzumile
Tanzania Journal of Engineering and Technology (TJET)
A systematic literature review was conducted to unveil the status of the digital transformation of metrology in developing countries, as they are lagging in utilising fourth industrial revolution (IR4.0) technologies to transform manufacturing industries. A PRISMA technique was employed using various keywords to identify, screen, and select the relevant literature. Forty publications were selected for the review, mainly discussing IR 4.0 technologies in metrological operations. The results indicate that the digital transformation of metrology has yet to be initiated in developing countries. However, the employment of IR4.0 technologies in advancing metrological operations in manufacturing industries is mostly discussed in the …
Effects Of Cutting Conditions On Tool Temperature And Material Removal Rate In Turning Operations,
2025
Department of Mechanical and Industrial Engineering, University of Dar es Salaam, P.O. Box 35131, Dar es Salaam, TANZANIA
Effects Of Cutting Conditions On Tool Temperature And Material Removal Rate In Turning Operations, Simon I. Marandu
Tanzania Journal of Engineering and Technology (TJET)
Cutting conditions in manufacturing processes have effects on tool temperature and material removal rate. The objective of this study was to investigate the effects of cutting conditions namely spindle speed, feed rate, depth of cut and tool nose radius on tool temperature and material removal rate in turning operations. A total of 81 experiments were conducted to measure tool temperature and material removal rate in order to determine the effects of cutting conditions on tool temperature and material removal rate using ANOVA and regression analysis. The results show that tool nose radius, depth of cut, and spindle speed are significant …
