Engineering Science and Materials Commons^™

Effect Of Saccharin On Crystallization Behavior Of Electroless Cobalt Plating, Yu-Xin Luo, Jing-Jing Wang, Lu Wang, Zi-Yi Yan, Yi Ma, Xin Bo, Jing-Shuang Dang, Zeng-Lin Wang

Journal of Electrochemistry

In the process of electroless cobalt plating, the saccharin additive can significantly change the surface morphology, texture orientation, and conductivity of the cobalt coating layer. When the amount of saccharin was 3 mg·L^–1, the cobalt coating transformed from disordered large grains to a honeycomb structure, with a preferred orientation of (002) facet on hexagonal close-packed (HCP) cobalt crystals. The resistivity of the cobalt film decreased to 14.4 μΩ·cm, and further decreased to 10.7 μΩ·cm after the annealing treatment. When the concentration of saccharin was increased, the grain size was gradually refined and a “stone forest” structure was observed, …

Design And Optimization Of Anode Catalysts For Direct Ethanol Fuel Cells: Advances And Challenges In C-C Bond Activation And Selective Modulation Of The C1 Pathway, Kai-Chi Qin, Meng-Tian Huo, Yu Liang, Si-Yuan Zhu, Zi-Hao Xing, Jin-Fa Chang

Journal of Electrochemistry

Direct ethanol fuel cells (DEFCs) are a promising alternative to conventional energy sources, offering high energy density, environmental sustainability, and operational safety. Compared to methanol fuel cells, DEFCs exhibit lower toxicity and a more mature preparation process. Unlike hydrogen fuel cells, DEFCs provide superior storage and transport feasibility, as well as cost-effectiveness, significantly enhancing their commercial viability. However, the stable C–C bond in ethanol creates a high activation energy barrier, often resulting in incomplete electrooxidation. Current commercial platinum (Pt)- and palladium (Pd)-based catalysts demonstrate low C–C bond cleavage efficiency (

Structure Regulation Engineering For Biomass-Derived Carbon Anodes Enabling High-Rate Dual-Ion Batteries, Rui Zhou, Rui Liu, Yun-Nuo Li, Si-Jie Jiang, Tian-Tian Jing, Yan-Song Xu, Fei-Fei Cao

Journal of Electrochemistry

Dual-ion batteries (DIBs) usually use carbon-based materials as electrodes, showing advantages in high operating voltage, potential low cost, and environmental friendliness. Different from conventional “rocking chair” type secondary batteries, DIBs perform a unique working mechanism, which employ both cation and anion taking part in capacity contribution at an anode and a cathode, respectively, during electrochemical reactions. Graphite has been identified as a suitable cathode material for anion intercalation at high voltages (> 4.8 V) with fast reaction kinetics. However, the development of DIBs is being hindered by dynamic mismatch between a cathode and an anode due to sluggish Li^{+ …}

Detection Of Bacterial Genomic Dna Fragments Using The Mxene Crispr-Cas9 Field-Effect Transistor, Jiaoli Li, Ali Taheri, Weijia Liu, Ying Zhuo, Pengfei Ma, Chenglin Wu

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Clustered regularly interspaced short palindromic repeats (CRISPR)-based field-effect transistor (FET) sensors provide a promising platform for highly specific and amplification-free nucleic acid detection. However, their direct application in identifying target sequences within intact genomic DNA remains underexplored. We developed a CRISPR-Cas9 FET sensor for detecting DNA sequences by immobilizing Cas9 onto a graphene-MXene sensing interface via (3-aminopropyl)triethoxysilane (APTES) functionalization. The sensor targeted Stx1, a 440 bp laboratory-amplified fragment associated with Shiga toxin production in pathogenic E. coli. Gel electrophoresis confirmed the precise cleavage of Stx1, while the nontarget sequence Stx2 remained undetected. FET measurements further validated the sensor's specificity, showing …

Ceramic Waste As Sustainable Material In Self-Compacting Concrete: Experimental Study And Ann Predictive Modeling, Abderrezak Bouziane, Houssam Slimanou, Mohamed Amin Bouzidi, Nedjima Bouzidi

Journal of Sustainable Construction Materials and Technologies

Recycling of ceramic waste in the construction sector is a promising option for reducing the environmental impacts of the concrete industry. The main objective of this study is the elaboration of a solid predictive model for ceramic waste based self-compacting (SCC) concrete properties, using artificial neural networks (ANN). This further, reduces its environmental impact without compromising satisfactory performance. An experimental approach was adopted with different substitution ratios: 0 to 30 wt% and particle sizes ranging from 3-8 mm and 8-15 mm. Tested properties of modified SCC as compressive strength at 7 and 28 days (fc7, fc28), spread (L), sieve stability …

Comparative Study On The Performance Of Ggbs, Uggbs, And Rha-Incorporated Cement Mortar Mixes, Devansh Goel, Sudarshan D. Kore

Journal of Sustainable Construction Materials and Technologies

The environmental footprint of cement production has accelerated the pursuit of sustainable alternatives in the construction industry. Supplementary cementitious materials (SCMs), particularly those derived from industrial and agricultural waste, offer a promising approach to reducing cement consumption while maintaining performance. This study evaluates the fresh and mechanical behavior of binary, ternary, and quaternary cementitious mortar blends incorporating ground granulated blast-furnace slag (GGBS), ultrafine GGBS (UGGBS), and rice husk ash (RHA) as partial replacements for cement. A total of 32 mortar mixes were designed with water-to-binder (w/b) ratios ranging from 0.3 to 0.5 and varied replacement levels of RHA (0-20%), GGBS …

Implementation Of Reliability Centered Maintenance On Crude Booster Pump, Dzulfikar Ali Hafizh, Maya Agustianingrum Putri St., Ph.D., D. Rizal, Adzra Qanita

Journal of Materials Exploration and Findings

Crude oil booster pump is one of the critical equipment in oil refinery operations. In aging plants that have been operating for more than 25 years, where reliability and maintenance issues on equipment often cause operational disruptions and even unplanned shutdowns. This study aims to develop a structured reliability-centered maintenance (RCM) strategy for crsude oil booster pump systems that is also in line with the principles of asset integrity management system (AIMS). This methodology follows the RCM II approach, starting with system function analysis, failure mode identification, and criticality assessment through Failure Mode, Effect, and Criticality Analysis (FMECA) to determine …

Functional Biopolymers Applied To Sustainable Technologies In The Environment And Healthcare, Fengjie He

UNLV Theses, Dissertations, Professional Papers, and Capstones

Biodegradable polymeric materials (biopolymers) are naturally derived materials known for their excellent biocompatibility, biodegradability, sustainability, and versatile chemical functionality. They have attracted increasing attention in various applications as alternative to synthetic materials ranging from food packaging to tissue engineering. Meanwhile, with intrinsic advantages, biopolymers have also emerged as promising materials in addressing contemporary challenges in both biomedical and environmental fields. Motivated by the significant potential of biopolymers and the growing need for sustainable materials, my research focuses on the design and engineering of biodegradable polymers with novel modification methods and application directions. In this work, two representative biopolymers are selected: …

Bio-Inspired Electroactive Polymer (Eap) Sensors For Surface And Canal Flow Sensing In Dynamic Environments, Nazanin Minaian

UNLV Theses, Dissertations, Professional Papers, and Capstones

Nature can often create some of the most efficient and elegant solutions to complex problems, and engineering stands to benefit greatly from these time-tested designs. One of the more sophisticated examples of this is the lateral line system in fish: a distributed network of superficial and canal neuromasts that enables aquatic species to detect fluid disturbances with remarkable precision. This dissertation leverages that biological framework to explore the potential of electroactive polymers (EAPs), aiming not just to replicate structure, but to emulate function.Two classes of EAPs form the basis of this work: electroactive plasticized polymer gels (EPPGs) and ionic polymer-metal …

Development Of Construction Materials With Natural Fibers And Flax Shives For Green Eco-Friendly Buildings. Mrs Advances (2025), Iman El-Mahallawi, Lamiaa Mohamed, Rania El‑Shorbagy, Mahmoud Tash, Aliaa Abdelfatah

Mechanical Engineering

Sustainability-oriented solutions are essential to address the depletion of natural resources, solid waste accumulation, and high CO2 emissions in the construction industry. This research focuses on the development of environmentally friendly green bricks by replacing high-carbon-footprint constituents with local, natural materials. Specifically, flax shives, a natural agricultural by-product, and marble powder, an industrial waste, were used as partial substitutes in the binder matrix. The natural fibers not only promote sustainability but also enhance insulation and reduce the environmental burden. The bricks were molded into rectangular specimens (60 × 100 × 200 mm) and tested for thermal conductivity, moisture absorption, and …

Mae Enewsbrief Apr- June 2025, Department Of Mechanical And Aerospace Engineering, Michigan Technological University

Department of Mechanical and Aerospace Engineering eNewsBrief

No abstract provided.

Mechanical Characterization Of M Plane (10-10) And C Plane (0001) Gallium Nitride Semiconductors Via Spherical Nanoindentation, Daniela Alejandra Duarte

Open Access Theses & Dissertations

Gallium nitride's (GaN) mechanical characterization is essential for evaluating its performance and long-term dependability, especially when subjected to mechanical stress and irradiation. The design and optimization of GaN-based devices, which are extensively employed in high-power electronics and optoelectronics, depend on an understanding of these characteristics. Mechanical characterization allows for the evaluation of key characteristics, including stress distributions, representing the spatial variation of internal stresses under applied loading, and pop-in events, which correspond to abrupt displacements associated with the onset of dislocation nucleation and slip. These features are essential for understanding the anisotropic (direction-dependent) response of the material to external forces …

Application Of Distributed Fiber Optic Sensing (Dfos) For Monitoring Asphalt Pavement Strains Under Accelerated Loading Conditions, Sebastian Morales

Open Access Theses & Dissertations

This thesis presents a study on the application of Distributed Fiber Optic Sensing (DFOS) technology for detecting pavement's strain response with high spatial resolution. Using a Rayleigh-based optical frequency domain reflectometry (OFDR) system, DFOS sensors were calibrated and embedded in full-scale asphalt slabs subjected to accelerated loading using a Model Mobile Load Simulator 3 (MMLS3). Calibration of the DFOS sensors was conducted using a three-point bending flexural test with known load conditions and reference strain gauges to validate theoretical and numerical models. The results demonstrate DFOS's capability to detect pavement response under static and dynamic loading, as well as changes …

Laser Scan Path Design For Controlled Microstructure In Additive Manufacturing With Integrated Reduced-Order Phase-Field Modeling And Deep Reinforcement Learning, Augustine Twumasi

Open Access Theses & Dissertations

Laser Powder Bed Fusion (L-PBF) is a well-established additive manufacturing technique for fabricating intricate metal components with exceptional precision. A significant challenge in L-PBF is the formation of complex microstructures that influence final material properties. We propose a physics-guided, machine learning-aided approach to optimize scan paths for desired microstructure outcomes, such as equiaxed grains. We employed a phase-field method (PFM) to model the evolution of the crystalline grain structure. To reduce computational costs, we trained a surrogate machine learning model, a 3D U-Net convolutional neural network, using single-track phase-field simulations with varying laser powers to predict crystalline grain orientations based …

Shape Memory Behavior In Medium To High Entropy Shape Memory Alloys: Design, Prediction, And Experimental Analysis, Hatim Raji

Theses and Dissertations

This dissertation provides a data-driven system integrating synthetic data generation and machine learning (ML) techniques to create multicomponent SMA compositions with specific transformation temperatures (TTs). Models were trained to represent the nonlinear dependencies influencing martensitic transformation behavior by using elemental, thermodynamic, and process-related aspects. The capacity of the ML models on medium entropy NiTiHfPd and high entropy NiTiHfZrCu systems accuracy was confirmed by experimental validation showing TTs closely matched with model outputs.

Advancing Multi-Physics Modeling For Microwave Heating: Application In Micro-Reactor Design And Optimization, Raghav Adhikari

All Theses

Microreactors are a type of small-scale chemical reactors for achieving reduced volume, improved product selectivity and higher reaction rate. It allows precise temperature control, which is crucial for sensitive chemical processes. Microreactors can be employed as key components of conducting small-scale reactions with improved reactor configuration and process efficiency. It is important to identify a localized and precise heating mechanism to trigger and control the corresponding chemical reactions.

In fact, microwave heating has gathered significant attention in recent years due to its ability to deliver efficient, rapid, and localized heating, which can accelerate reaction rates and enhances the reaction selectivity. …

Quantifying The Effect Of Initial Molecular Weight Distribution On The Degradation Of Linear Polyethylene At High Temperatures Using Dissipative Particle Dynamics, Cassandra L. Simpson

All Theses

Polyolefins are the primary contributors to greenhouse gas emissions and supply chain energy requirements with respect to other commodity polymers. In order to explore more efficient methods for recycling and upcycling these plastics, it is important to consider the kinetics of polymer fragments during the degradation process to more accurately reflect experimental outcomes. The molecular weight distribution of synthetic polymers is an important factor to consider when synthesizing, processing, and manufacturing industrial plastics. The breadth of this distribution, or dispersity, is determined by the ratio of the weight average molecular weight to the number average molecular weight, and is correlated …

Advancing Real-World Implementation Of The Well Optimized Linear Finder (Wolf) High-Speed Atmospheric Turbulence Compensation Method, Timothy Evan Coon

Theses and Dissertations

This dissertation advances the real-world implementation of the Well Optimized Linear Finder (WOLF) method for high-speed Atmospheric Turbulence Compensation (ATC). Atmospheric turbulence introduces phase aberrations into optical wavefronts and degrades image quality in terrestrial imaging systems. Traditional phase diversity methods are computationally intensive and poorly suited to real-time operation. The WOLF method addresses these limitations through a novel, point-wise formulation of the optical transfer function (OTF) as a structured autocorrelation of the generalized pupil function (GPF). This formulation enables the estimation of phase aberrations at individual spatial coordinates with distributed computational complexity.

The research begins by developing a MATLAB-based simulation …

Utilization Of Biomass From Kerai Payung Trees And Waste Paper Through Pyrolysis Technology To Support The Zero-Waste Concept, Anggita Putri Indadari, Nurfa Anisa, Asih Budi Santoso

Journal of Mechanical Engineering Science and Technology (JMEST)

Wisnuwardhana University is a private institution with a green campus environment surrounded by Kerai Payung trees. This environment produces organic waste from trees and inorganic waste such as used paper from campus activities. This study aims to achieve zero-waste processing by using pyrolysis technology to process campus waste, ensuring minimal residue. The experimental method involves comparing waste processing outcomes between conventional combustion and pyrolysis, the data was analyzed by comparing the results of pyrolysis with conventional combustion. The results of biochar from the pyrolysis process of used paper, Kerai Payung leaves, and nagging Kerai Payung tree are 76 g, 250 …

Dynamic Analysis And Fatigue Life Evaluation Of Single Herringbone Planetary Gear System With Crack Fault, Dongping Sheng, Jie Yang, Chun Su

Journal of Mechanical Engineering Science and Technology (JMEST)

The herringbone planetary gear transmission is widely used due to its exquisite compact structure, excellent load-bearing capacity, and stable transmission characteristics. However, root crack is one of the most common failure modes of gears. A cracked herringbone planetary gear system is taken as research object. The sun gear with crack fault is studied from the aspect of modal and transient dynamic analysis, and the related results are compared with the healthy gear. Based on the transient dynamic analysis of the herringbone teeth with cracks, a fatigue life evaluation is conducted. Firstly, the results show that no significant difference between the …