Other Engineering Science and Materials Commons^™

Traversing With Quantitative Fidelity Through The Glass Transition Of Amorphous Polymers: Modeling The Thermodynamic Dilatational Flow Of Polycarbonate, Mehrdad Negahban, Wenlong Li, Jean-Marc Saiter, Laurent Delbreilh, Kyle Strabala, Zheng Li

Department of Mechanical and Materials Engineering: Faculty Publications

We follow the assumption that the dilatational response of glassy polymers can be characterized by a back-stress type analog that includes a thermal expansion for each elastic component, and with a viscosity that is dependent on the expansion of the elastic back stress component. To this, we add the assumption of an unloaded equilibrium temperature that correlates to the past processing through the viscous flow. After setting this in a thermodynamically consistent structure, the elastic, elastic backstress, thermal expansion, back-stress thermal expansion, heat capacity and viscous damping are evaluated using existing experiments for the response of polycarbonate over the glassy …

Pinch Force Generation During Scaling By Dental Professionals: A Systematic Review, Jessica R. Suedbeck, Emily A. Ludwig

Dental Hygiene Faculty Publications

Objective

The objective of this review was to examine the impact of instrument designs on pinch force generation during scaling by dental professionals.

Methods

Three databases were utilized from September 2019 to November 2021 in addition to hand-searching specific journals and reference lists. Research articles that examined pinch force generation in dental professionals during scaling with manual instruments only were included. Bias was assessed in the individual articles.

Results

Six research articles were included with sample populations that varied from 12 to 24 participants. Four articles evaluated instrument designs in relation to pinch force generation during scaling by dental professionals. …

Peridynamic Simulation Of Elastic Wave Propagation By Applying The Boundary Conditions With The Surface Node Method, Francesco Scabbia, Mirco Zaccariotto, Ugo Galvanetto, Florin Bobaru

Department of Mechanical and Materials Engineering: Faculty Publications

Peridynamics is a novel nonlocal theory able to deal with discontinuities, such as crack initiation and propagation. Near the boundaries, due to the incomplete nonlocal region, the peridynamic surface effect is present, and its reduction relies on using a very small horizon, which ends up being expensive computationally. Furthermore, the imposition of nonlocal boundary conditions in a local way is often required. The surface node method has been proposed to solve both the aforementioned issues, providing enhanced accuracy near the boundaries of the body. This method has been verified in the cases of quasi-static elastic problems and diffusion problems evolving …

Advanced Modeling And Innovative Transcranial Magnetic Stimulation Coil Designs For The Treatment Of Neurological Disorders, Mohannad Tashli

Theses and Dissertations

Transcranial magnetic stimulation (TMS) is a safe, effective and non-invasive treatment for several mental and psychiatric disorders. TMS is an FDA approved treatment and is commonly applied to patients who do not respond to medications for the treatment of clinical depression, smoking cessation, obsessive-compulsive disorder and migraine. Recently, there has been an increase in the development of electromagnetic neuromodulation techniques targeted at enhancing the effectiveness of TMS devices for the treatment of mental diseases. In TMS stimulation, focality is an important factor which determines the specificity of the pulses induced in different brain tissues. The electromagnetic pulses must be confined …

Assessing A Byproduct Of The Cbd Ethanol Extraction Process For Potential As A Wood Finishing Product, Avani M. Flanagan

Masters Theses

Developments in regulations concerning the use of CBD products as therapeutic remedies have allowed the global cannabidiol (CBD) market to take off within the past five years. Despite producers of CBD oil wanting to optimize their methods and increase product yields, several waste streams still exist. During the winterization phase of the ethanol extraction process, CBD oil is cooled and filtered so the fats, waxes, and lipids from the Cannabis sativa plant can coagulate and be removed, creating a purer oil with higher potency but contributing to the 58% (crude weight) total loss that occurs throughout the process. The removed …

Understanding The Feasibility Of Improving Interfacial Properties In Direct Ink Writing Of Silicone-Polyurethane Resin Hybrid Material, Ayobami Samuel Akinfenwa

College of Graduate Studies: Theses & Dissertations

The progress in materials engineering and the ability to make various models possible have made soft robotics a popular alternative to traditional robotics. Still, soft robots need various parts, like Printed Circuit Boards (PCBs), batteries, cables, fittings, and more, to work correctly or to get attached to other complex parts. These parts can have different material properties, like elastic moduli, strength, etc. Because of these differences, mechanical failures happen at the points where two materials meet, making soft robots less durable and less lasting in real-life situations due to failure. Conventionally, the fabrication of soft robot parts is through moulding. …

Fem Eem Dataset: Optimising Retrofitted Insulation For Irish Residential Building Walls, Rakshit D. Muddu, Aimee Byrne, Anthony Robinson Dr.

Datasets

A large number of combinations of Irish wall types, insulation materials, and heating fuel types were produced to compare the multiple variables which influence Optimal Insulation Thickness values. The total cost (TC) and carbon emission (CE) at optimum insulation thickness (OIT) for all combinations of insulation material and three types of fuel are considered. The dataset presents OIT for solid wall, cavity wall and cavity block wall types located in Monaghan, Dublin, and Kerry.

Development Of Inconel 718f And Inconel 718e Powders For Parts Manufacturing Utilizing Binder Jet Three-Dimensional Printing And Compressed Pellet Methods, Duncan Eric Manor Ii

Graduate Theses, Dissertations, and Problem Reports (ETD)

Alloy Inconel 718 is a Ni based superalloy used for high temperature applications including turbine blades, turbocharger rotors and nuclear reactors. Inconel 718 is a popular commercial atomized powder that has limitations in performance for use in additive manufacturing applications due to poor part quality and efficiency of current fabrication methods. Developing new compositions and additive manufacturing (AM) methodologies of IN718 is critical to improve the quality and the efficiency of IN718 parts manufacturing. Developing new additive manufacturing methodology that produces higher quality parts made of IN718 as compared to current methods has the potential to greatly impact industry, academia, …

Phase-Averaged, Frequency Dependence Of Jet Dynamics In A Scaled Up Vocal Fold Model With Full And Incomplete Closure, Nathaniel Wei, Abigail Haworth, Hunter Ringenberg, Michael Krane, Timothy Wei

Department of Mechanical and Materials Engineering: Faculty Publications

This study focuses on frequency dependence effects on glottal jet dynamics with a focus on the physiological condition in which the vocal folds do not fully close. Incomplete closure occurs naturally in children and adult females. But there are also pathological conditions that can be problematic. Experiments were conducted using a 10× scaled-up model in a free surface water tunnel. Two-dimensional vocal fold models with semicircular medial surfaces were stepper motor driven inside a square duct with constant opening and closing speeds. Cases with complete vocal fold closure and incomplete closure to only 15% of the maximum gap were examined. …

Sars-Cov-2 Detecting Rapid Metasurface-Based Sensor, Shobhit K. Patel, Jaymit Surve, Juveriya Parmar, Khaled Aliqab, Meshari Alsharari, Ammar Armghan

Department of Mechanical and Materials Engineering: Faculty Publications

We have proposed a novel approach to detect COVID-19 by detecting the ethyl butanoate which high volume ratio is present in the exhaled breath of a COVID-19 infected person. We have employed a refractive index sensor (RIS) with the help of a metasurface-based slotted T-shape perfect absorber that can detect ethyl butanoate present in exhaled breath of COVID-19 infected person with high sensitivity and in-process SARS-CoV-2. The optimized structure of the sensor is obtained by varying several structure parameters including structure length and thickness, slotted T-shape resonator length, width, and thickness. Sensor’s performance is evaluated based on numerous factors comprising …

Nanoscale Imaging Of Antiferromagnetic Domains In Epitaxial Films Of Cr2O3 Via Scanning Diamond Magnetic Probe Microscopy, Adam Erickson, Syed Qamar Abbas Shah, Ather Mahmood, Ilja Fescenko, Christian H. Binek, Adbelghani Laraoui

Department of Mechanical and Materials Engineering: Faculty Publications

We report direct imaging of boundary magnetization associated with antiferromagnetic domains in magnetoelectric epitaxial Cr₂O₃ thin films using diamond nitrogen vacancy microscopy. We found a correlation between magnetic domain size and structural grain size which we associate with the domain formation process. We performed field cooling, i.e., cooling from above to below the Néel temperature in the presence of a magnetic field, which resulted in the selection of one of the two otherwise degenerate 180° domains. Lifting of such a degeneracy is achievable with a magnetic field alone due to the Zeeman energy of a weak …

Experimental Tests And Numerical Study Of Trajectories Of Different Types Of Dropped Objects, Yi Li

LSU New Orleans Theses and Dissertations

In marine and offshore engineering, dropped objects, such as drill pipes, anchor chains, containers and some small parts, can accidentally fall into the water from ships or offshore platforms, causing casualties on deck or damage to underwater equipment. Damaged equipment can further harm the environment, such as oil spills from damaged wellheads. Therefore, for safe engineering and environmental protection reasons, we need to develop methods and tools that can predict the trajectory of dropped objects.

In this dissertation, we first study containers dropped from ships. More and more containers are falling into the sea due to bad weather. Containers lost …

High Throughput And Highly Controllable Methods For In Vitro Intracellular Delivery, Justin Brooks, Grayson Minnick, Prithvijit Mukherjee, Arian Jaberi, Lingqian Chang, Horacio D. Espinosa, Ruiguo Yang

Department of Mechanical and Materials Engineering: Faculty Publications

In vitro and ex vivo intracellular delivery methods hold the key for releasing the full potential of tissue engineering, drug development, and many other applications. In recent years, there has been significant progress in the design and implementation of intracellular delivery systems capable of delivery at the same scale as viral transfection and bulk electroporation but offering fewer adverse outcomes. This review strives to examine a variety of methods for in vitro and ex vivo intracellular delivery such as flow-through microfluidics, engineered substrates, and automated probe-based systems from the perspective of throughput and control. Special attention is paid to a …

Efects Of Non‑Newtonian Viscosity On Arterial And Venous Fow And Transport, Sabrina Lynch, Nitesh Nama, C Alberto Figueroa

Department of Mechanical and Materials Engineering: Faculty Publications

It is well known that blood exhibits non-Newtonian viscosity, but it is generally modeled as a Newtonian fluid. However, in situations of low shear rate, the validity of the Newtonian assumption is questionable. In this study, we investigated differences between Newtonian and non-Newtonian hemodynamic metrics such as velocity, vorticity, and wall shear stress. In addition, we investigated cardiovascular transport using two different approaches, Eulerian mass transport and Lagrangian particle tracking. Non-Newtonian solutions revealed important differences in both hemodynamic and transport metrics relative to the Newtonian model. Most notably for the hemodynamic metrics, in-plane velocity and vorticity were consistently larger in …

Enhanced Electron Correlation And Significantly Suppressed Thermal Conductivity In Dirac Nodal-Line Metal Nanowires By Chemical Doping, Amanda L. Coughlin, Zhiliang Pan, Jeonghoon Hong, Tongxie Zhang, Xun Zhan, Wenqian Wu, Dongyue Xie, Tian Tong, Thomas Ruch, Jean J. Heremans, Jiming Bao, Herbert A. Fertig, Jian Wang, Jeongwoo Kim, Hanyu Zhu, Deyu Li, Shixiong Zhang

Department of Mechanical and Materials Engineering: Faculty Publications

Enhancing electron correlation in a weakly interacting topological system has great potential to promote correlated topological states of matter with extraordinary quantum properties. Here, the enhancement of electron correlation in a prototypical topological metal, namely iridium dioxide (IrO₂), via doping with 3d transition metal vanadium is demonstrated. Single-crystalline vanadium-doped IrO₂ nanowires are synthesized through chemical vapor deposition where the nanowire yield and morphology are improved by creating rough surfaces on substrates. Vanadium doping leads to a dramatic decrease in Raman intensity without notable peak broadening, signifying the enhancement of electron correlation. The enhanced electron correlation is further …

Exosomes Derived From Differentiated Human Admsc With The Schwann Cell Phenotype Modulate Peripheral Nerve-Related Cellular Functions, Bo Liu, Yunfan Kong, Wen Shi, Mitchell Kuss, Ke Liao, Guoku Hu, Peng Xiao, Jagadesan Sankarasubramanian, Chittibabu Guda, Xinglong Wang, Yuguo Lei, Bin Duan

Department of Mechanical and Materials Engineering: Faculty Publications

Peripheral nerve regeneration remains a significant clinical challenge due to the unsatisfactory functional recovery and public health burden. Exosomes, especially those derived from mesenchymal stem cells (MSCs), are promising as potential cell-free therapeutics and gene therapy vehicles for promoting neural regeneration. In this study, we reported the differentiation of human adipose derived MSCs (hADMSCs) towards the Schwann cell (SC) phenotype (hADMSC-SCs) and then isolated exosomes from hADMSCs with and without differentiation (i.e., dExo vs uExo). We assessed and compared the effects of uExo and dExo on antioxidative, angiogenic, antiinflammatory, and axon growth promoting properties by using various peripheral nerve-related cells. …

Phase Space Analysis Of Nonlinear Wave Propagation In A Bistable Mechanical Metamaterial With A Defect, Mohammed A. Mohammed, Piyush Grover

Department of Mechanical and Materials Engineering: Faculty Publications

We study the dynamics of solitary waves traveling in a one-dimensional chain of bistable elements in the presence of a local inhomogeneity (“defect”). Numerical simulations reveal that depending upon its initial speed, an incoming solitary wave can get transmitted, captured, or reflected upon interaction with the defect. The dynamics are dominated by energy exchange between the wave and a breather mode localized at the defect. We derive a reduced-order two degree of freedom Hamiltonian model for wave-breather interaction and analyze it using dynamical systems techniques. Lobe dynamics analysis reveals the fine structure of phase space that leads to the complicated …

Feedforward Control Of Thermal History In Laser Powder Bed Fusion: Toward Physics-Based Optimization Of Processing Parameters, Alex Riensche, Benjamin D. Bevans, Ziyad M. Smoqi, Reza Yavari, Ajay Krishnan, Josie Gilligan, Nicholas Piercy, Kevin D. Cole, Prahalada K. Rao

Department of Mechanical and Materials Engineering: Faculty Publications

We developed and applied a model-driven feedforward control approach to mitigate thermal-induced flaw formation in laser powder bed fusion (LPBF) additive manufacturing process. The key idea was to avert heat buildup in a LPBF part before it is printed by adapting process parameters layer-by-layer based on insights from a physics-based thermal simulation model. The motivation being to replace cumbersome empirical build-and-test parameter optimization with a physics-guided strategy. The approach consisted of three steps: prediction, analysis, and correction. First, the temperature distribution of a part was predicted rapidly using a graph theory-based computational thermal model. Second, the model-derived thermal trends were …

A Method Of Assessing Peripheral Stent Abrasiveness Under Cyclic Deformations Experienced During Limb Movement, Courtney Keiser, Kaspars Maleckis, Pauline Struczewska, Majid Jadidi, Jason N. Mactaggart, Alexey Kamenskiy

Department of Mechanical and Materials Engineering: Faculty Publications

Poor outcomes of peripheral arterial disease stenting are often attributed to the inability of stents to accommodate the complex biomechanics of the flexed lower limb. Abrasion damage caused by rubbing of the stent against the artery wall during limb movement plays a significant role in reconstruction failure but has not been characterized. Our goals were to develop a method of assessing the abrasiveness of peripheral nitinol stents and apply it to several commercial devices. Misago, AbsolutePro, Innova, Zilver, SmartControl, SmartFlex, and Supera stents were deployed inside electrospun nanofibrillar tubes with femoropopliteal artery-mimicking mechanical properties and subjected to cyclic axial compression …

Revealing The Pulse-Induced Electroplasticity By Decoupling Electron Wind Force, Xing Li, Qi Zhu, Youran Hong, He Zheng, Jian Wang, Jiangwei Wang, Ze Zhang

Department of Mechanical and Materials Engineering: Faculty Publications

Micro/nano electromechanical systems and nanodevices often suffer from degradation under electrical pulse. However, the origin of pulse-induced degradation remains an open question. Herein, we investigate the defect dynamics in Au nanocrystals under pulse conditions. By decoupling the electron wind force via a properly-designed in situ TEM electropulsing experiment, we reveal a non-directional migration of Σ3{112} incoherent twin boundary upon electropulsing, in contrast to the expected directional migration under electron wind force. Quantitative analyses demonstrate that such exceptional incoherent twin boundary migration is governed by the electron-dislocation interaction that enhances the atom vibration at dislocation cores, rather than driven by the …