Other Engineering Science and Materials Commons^™

Dual-Axis Solar Tracker, Bryan Kennedy

All Undergraduate Projects

Renewable energies, and fuels that are not fossil fuel-based, are one of the prolific topics of debate in modern society. With climate change now becoming a primary focus for scientists and innovators of today, one of the areas for the largest amount of potential and growth is that of the capturing and utilization of Solar Energy. This method involves using a mechanical system to track the progression of the sun as it traverses the sky throughout the day. A dual-axis solar tracker such as the one designed and built for this project, can follow the sun both azimuthally and in …

Hierarchical Mechanisms Of Lateral Interactions In High- Performance Fibers, Taylor A, Stockdale, Daniel P. Cole, Jeffrey M. Staniszewski, Michael R. Roenbeck, Dimitry Papkov, Steve R. Lustig, Youris A. Dzenis, Kenneth E. Strawhecker

Department of Mechanical and Materials Engineering: Faculty Publications

The processing conditions used in the production of advanced polymer fibers facilitate the formation of an oriented fibrillar network that consists of structures spanning multiple length scales. The irregular nature of fiber tensile fracture surfaces suggests that their structural integrity is defined by the degree of lateral (interfacial) interactions that exist within the fiber microstructure. To date, experimental studies have quantified interfacial adhesion between nanoscale fibrils measuring 10−50 nm in width, and the global fracture energy through applying peel loads to fiber halves. However, a more in-depth evaluation of tensile fracture indicates that fiber failure typically occurs at an intermediate …

Cardiorespiratory Fitness, Balance And Walking Improvements In An Adolescent With Cerebral Palsy (Gmfcs Ii) And Autism After Motor-Assisted Elliptical Training, Guilherme Manna Cesar, Thad W. Buster, Judith M. Burnfield

Department of Mechanical and Materials Engineering: Faculty Publications

Purpose: To quantify the impact of motor-assisted elliptical (ICARE) training on cardiorespiratory fitness, balance and walking function of an adolescent with walking limitations due to cerebral palsy.

Materials and methods: A thirteen-year-old boy with hemiplegic cerebral palsy (Gross Motor Function Classification System II) and autism participated. Peak oxygen consumption (peak VO₂, primary outcome measure), oxygen cost of walking, Pediatric Balance Scale (PBS), modified Timed Up and Go (mTUG), 2-Minute Walk Test (2MWT), and gait characteristics (speed, cadence, step length, single support time) were assessed prior to and after completion of 24 sessions of moderate- to vigorous- intensity ICARE …

Three-Dimensional Characterization Of Peripapillary Retinal Pigment Epithelium-Basement Membrane Layer In Patients Following Lumbar Puncture, Junfei Tong, Pengfei Dong, Sachin Kedar, Deepta Ghate, Linxia Gu

Department of Mechanical and Materials Engineering: Faculty Publications

Purpose: To develop and test an innovative semi-automatic method for quantifying the three-dimensional morphology of the peripapillary retinal pigment epithelium-basement membrane (ppRPE/BM) layer, with application to lumbar puncture (LP) patients. Methods: Nineteen patients undergoing LP were recruited. The optic nerve head images of both eyes were acquired in 12 radial directions using optical coherence tomography (OCT) before and after LP. For each OCT image, the ppRPE/BM layer was automatically segmented with manual corrections by independent graders when necessary. The linear regression model of the ppRPE/BM layer was fitted using the least squares approach, and the ppRPE/BM layer angle was measured …

Roboticdeviceswithonboard Control And Related Systems And Devices, Shane Michael Farritor, Erik Mumm, Philip Chu, Nishant Kumar, Jason Dumpert, Yutaka Tsutano

Department of Mechanical and Materials Engineering: Faculty Publications

The embodiments disclosed herein relate to various medical device components, including components that can be incorporated into robotic and/or in vivo medical devices. Certain embodiments include various modular medical devices for in vivo medical procedures.

Role Of Interfacial Transition Zones In The Fracture Of Cu/V Nanolamellar Multilayers, Siyuan Wei, Shijian Zheng, Lifeng Zhang, Yue Liu, Jian Wang, Xianping Wang, Jiangwei Wang

Department of Mechanical and Materials Engineering: Faculty Publications

Plastic deformation and fracture behavior of Cu/V nanoscale metallic multilayers (NMMs) were systematically investigated through in situ transmission electron microscopy testing. Two different types of interfaces: sharp interfaces and interfacial transition zones (ITZs), formed in the as-fabricated Cu/V NMMs. Upon deformation, sharp interfaces and ITZs exert distinct influences on the fracture behavior of Cu/V NMMs. Sharp interfaces can impede the crack propagation by deflecting the crack propagation and blunting the crack tip, while the ITZs can induce microcracks and facilitate the fracture process. These findings shed light on the important roles of interface structures in the deformation of a broad …

Low- And High-Drag Intermittencies In Turbulent Channel Flows, Rishav Agrawal, Henry C.-H. Ng, Ethan A. Davis, Jae Sung Park, Michael D. Graham, David J.C. Dennis, Robert J. Poole

Department of Mechanical and Materials Engineering: Faculty Publications

Recent direct numerical simulations (DNS) and experiments in turbulent channel flow have found intermittent low- and high-drag events in Newtonian fluid flows, at Reτ = uτh/ν between 70 and 100, where uτ, h and ν are the friction velocity, channel half-height and kinematic viscosity, respectively. These intervals of low-drag and high-drag have been termed “hibernating” and “hyperactive”, respectively, and in this paper, a further investigation of these intermittent events is conducted using experimental and numerical techniques. For experiments, simultaneous measurements of wall shear stress and velocity are carried out in a channel flow facility using hot-film anemometry (HFA) and laser …

Multi-Well Plate Channel Device With Reversible Seals, Haipeng Zhang, Timothy Wei, Sangjin Ryu

Department of Mechanical and Materials Engineering: Faculty Publications

Atherosclerosis is a cardiovascular disease which causes over 26,000 yearly deaths in the United States. This disease involves accumulation of substances in arterial walls (or plaques) that occurs frequently to arterial regions experiencing low shear stress, such as bends and bifurcations. A possible reason of plaque growth in arterial walls is the change of endothelial cell (EC)’s shape, which is related to fluid shear stresses tangentially acting on intimal layer (the EC surface) of the arterial wall. Lambert et al. studied the relationship between EC shape and shear stress (Lambert et al., 2019) using a BioFlux system (Fluxion Bioscienes) and …

Universal Mechanical Exfoliation Of Large-Area 2d Crystals, Yuan Huang, Yu-Hao Pan, Rong Yang, Li-Hong Bao, Lei Meng, Hai-Lan Luo, Yong-Qing Cai, Guo-Dong Liu, Wen-Juan Zhao, Zhang Zhou, Liang-Mei Wu, Zhi-Li- Zhu, Ming Huang, Li-Wei Liu, Lei Liu, Peng Cheng, Ke-Hui Wu, Shi-Bing Tian, Chang-Zhi Gu, You-Guo Shi, Yan-Feng Guo, Zhi Gang Cheng, Jiang-Ping Hu, Lin Zhao, Guan-Hua Yang, Eli Sutter, Peter Sutter, Ye-Liang Wang, Wei Ji, Xing-Jiang Zhou, Hong-Jun Gao

Department of Mechanical and Materials Engineering: Faculty Publications

Two-dimensional materials provide extraordinary opportunities for exploring phenomena arising in atomically thin crystals. Beginning with the first isolation of graphene, mechanical exfoliation has been a key to provide high-quality two-dimensional materials, but despite improvements it is still limited in yield, lateral size and contamination. Here we introduce a contamination-free, one-step and universal Au-assisted mechanical exfoliation method and demonstrate its effectiveness by isolating 40 types of single-crystalline monolayers, including elemental two-dimensional crystals, metal-dichalcogenides, magnets and superconductors. Most of them are of millimeter-size and high-quality, as shown by transfer-free measure- ments of electron microscopy, photo spectroscopies and electrical transport. Large sus- pended …

Benign Ferroelastic Twin Boundaries In Halide Perovskites For Charge Carrier Transport And Recombination, Xun Xiao, Wenhao Li, Yanjun Fang, Ye Liu, Yuchuan Shao, Shuang Yang, Jingjing Zhao, Xuezeng Dai, Rashid Zia, Jinsong Huang

Department of Mechanical and Materials Engineering: Faculty Publications

Grain boundaries have been established to impact charge transport, recombination and thus the power conversion efficiency of metal halide perovskite thin film solar cells. As a special category of grain boundaries, ferroelastic twin boundaries have been recently discovered to exist in both CH3NH3PbI3 thin films and single crystals. However, their impact on the carrier transport and recombination in perovskites remains unexplored. Here, using the scanning photocurrent microscopy, we find that twin boundaries have negligible influence on the carrier transport across them. Photoluminescence (PL) imaging and the spatial-resolved PL intensity and lifetime scanning confirm the electronically benign nature of the twin …

Variations In Plantar Pressure Variables Across Elliptical Trainers In Older Adults, Judith M. Burnfield, Guilherme Manna Cesar, Thad W. Buster

Department of Mechanical and Materials Engineering: Faculty Publications

Background: Ellipticals are used to address walking and cardiorespiratory training goals of older adults, some of whom are at risk for foot injuries. Variations in joint kinematics and muscle demands when using different ellipticals could lead to plantar pressure differences. This study explored plantar pressure variables during gait and use of four ellipticals.

Methods: Plantar pressures were recorded while 10 adults [68.1 (4.5) years] walked and used the True, Octane, Life Fitness, and SportsArt ellipticals. Repeated-measures ANOVAs (5 × 1) identified forefoot and heel differences across conditions.

Findings: Maximum forefoot forces and peak pressures were significantly lower than walking for …

Ultrahigh Strength And Plasticity In Laser Rapid Solidified Al–Si Nanoscale Eutectics, Huai-Hsun Lien, Jyoti Mazumder, Jian Wang, Amit Misra

Department of Mechanical and Materials Engineering: Faculty Publications

As-cast Al–20wt.% Si alloys were processed via laser rapid solidification (LRS) techniques to create eutectic microstructures with nanoscale interconnected, nanotwinned Si fibers. LRS morphologies exhibit higher flow stress, exceeding 800 MPa and uniform plastic deformation above 20% compared to as-cast alloy that fractures at strains below 8% at flow strength of approximately 200 MPa. The strengthening mechanisms of LRS morphologies are interpreted in terms of the interfacial constraints: increase in yield strength as well as strain hardening rate due to nanoscale confined slip in fibrous Al–Si eutectic, and load transfer and eventual plasticity in the nanoscale Si fibers.

Leidenfrost Droplet Microfluidics, Sidy Ndao, George Gogos, Dennis Alexander, Troy Anderson, Craig Zuhlke

Department of Mechanical and Materials Engineering: Faculty Publications

Systems and methods are described for propelling a liquid droplet in a Leidenforst state. A microfluidic device embodiment includes, but is not limited to, a solid structure having a patterned surface, the patterned surface including at least a first patterned region having a first Leidenfrost temperature with respect to a fluid, the first patterned region adjacent to the second patterned region, the first patterned region defining a path over which a droplet of the fluid is configured to travel in a Leidenfrost state.

Iron Pyrite Nanocrystals, Jinsong Huang, Baodong Mao, Christopher L. Exstrom

Department of Mechanical and Materials Engineering: Faculty Publications

An apparatus includes a nanocrystal. The nanocrystal includes a core including FeS2; and a coating including a ligand component capable of chemically interacting with both an iron atom and a sulfur atom on a surface of the core.

Colocalized Sensing And Intelligent Computing In Micro-Sensors, Mohammad H. Hasan, Ali Al-Ramini, Eihab Abdel-Rahman, Roozbeh Jafari, Fadi Alsaleem

Department of Mechanical and Materials Engineering: Faculty Publications

This work presents an approach to delay-based reservoir computing (RC) at the sensor level without input modulation. It employs a time-multiplexed bias to maintain transience while utilizing either an electrical signal or an environmental signal (such as acceleration) as an unmodulated input signal. The proposed approach enables RC carried out by sufficiently nonlinear sensory elements, as we demonstrate using a single electrostatically actuated microelectromechanical system (MEMS) device. The MEMS sensor can perform colocalized sensing and computing with fewer electronics than traditional RC elements at the RC input (such as analog- to-digital and digital-to-analog converters). The performance of the MEMS RC …

Microstructural Evolution Of Nanotwinned Al-Zr Alloy With Significant 9r Phase, N.A. Richter, Y.F. Zhang, D. Y. Xie, R. Su, Q. Li, S. Xue, T. Niu, J. Wang, H. Wang, Xinghang Zhang

Department of Mechanical and Materials Engineering: Faculty Publications

Aluminum (Al) alloys have a multitude of applications, notably in the automotive, aerospace and coating industries, yet they exhibit significantly lower mechanical strength than conventional steels. Nanotwins drastically improve mechanical strength while retaining ductility. However, the high SFE of Al largely prevents twinning. Here, we synthesize Al-Zr alloy films containing an abundance of incoherent twin boundaries and 9R phases. These alloys exhibit an extended solid solubility of Zr, retaining a columnar nanotwinned structure across all compositions. These films reach a hardness up to 4.2 GPa with 10 at% Zr and demonstrate the capacity for producing strong Al alloys with nanotwins.

Nonhydrostatic Modeling Of Flow Interactions With Highly Flexible Vegetation, Navid Tahvildari, Ramin Familkhalili, Gangfeng Ma

Civil & Environmental Engineering Faculty Publications

Improving our understanding of the interactions between gravity waves, currents, and coastal vegetation, which are nonlinear in nature, enables coastal engineers and managers to better estimate hydrodynamic forces on coastal infrastructure and utilize natural elements to mitigate their impacts. Aquatic vegetation is ubiquitous in coastal waters and it is well-known that flow loses energy over vegetation. Computational modeling of wave-vegetation interaction has been the subject of numerous recent studies and many improvements have been achieved in reducing limitations applied on wave and vegetation behavior in these models. Mechanisms for highly flexible vegetation have been incorporated in a Boussinesq-type model and …

Jominy Hardenability Tester With In-Situ Heating, Luke Allen

Williams Honors College, Honors Research Projects

This project centers on building a Jominy Hardenability tester with In-Situ heating for the manufacturing lab at the University of Akron. A new process and setup will be designed using engineering concepts in order to make the testing more efficient and safer for the teaching and testing of metal hardness. The current Jominy testing setup has efficiency issues within the transfer of specimen from induction heater to testing rig. Our design will simplify the design by creating a test rig that removes the traveling aspect of the specimen which will limit the amount of premature cooling done and will be …

Determination And Validation Of Mechanical Properties Of Materials And Substructures, Karl Bates

Williams Honors College, Honors Research Projects

The nature of this project is confidential and cannot be disclosed in detail. Generally, this project involves the manufacturing of an original design, which is subjected to a variety of tests – including tensile, compressive, bending, fatigue, and environmental testing, as well as qualitative destructive tests – to determine the mechanical properties of the component. This testing data compares with values predicted using Finite-Element Analysis. The validation of predicted FEM values is crucial to the success of this component, as it is designed for lifecritical applications. If test results indicate poor structural performance, considerable redesign will be necessary.

Tabletop Mechanical Tester, Jamie Dombroski, Brian English, Richard Leffler, Andrew Shirk

Williams Honors College, Honors Research Projects

The need for hands-on and face-to-face experiences in the engineering classroom is very great. The equations, principles, and concepts can all be learned, but without the visual and tactile application, these don’t always sink in or become concrete. A small-scale tensile test machine was designed, sourced, manufactured, and tested for the purpose of being applied in classroom settings to provide this experience to engineering students. Extensive research was performed concerning tensile machines on the market, the essential elements of which are the load cell, grips, crosshead, extensometer, motor, and frame. The raw materials for the frame were purchased and drawings …