Structural Engineering Commons^™

Protecting Bridges From Earthquake Damage, Peter Dusicka

TREC Project Briefs

Earthquake damage to bridges can have serious effects on a transportation network. When a bridge is out, the damage can go well beyond what is immediately visible: in addition to the cost of repairing it, the state must deal with short-term and long-term interruptions to traffic. These interruptions can delay repair and construction, as well as impacting post earthquake emergency response and causing the loss of valuable time for commuters and freight. To prevent this situation, older bridges (ones that are past an average construction life of about 50 years) should be retrofitted with stronger materials, especially in earthquake- prone …

Sheathing Braced Design Of Wall Studs, B. W. Schafer

American Iron and Steel Institute (AISI) Specifications, Standards, Manuals and Research Reports (1946 - present)

This report was prepared as part of the American Iron and Steel Institute sponsored project: Sheathing Braced Design of Wall Studs. The project also received supplementary support and funding from the Steel Stud Manufacturers Association. Additional project information and documentation is available at www.ce.jhu.edu/bschafer/sheathedwalls. Any opinions, findings, and conclusions or recommendations expressed in this publication are those of the author and do not necessarily reflect the views of the American Iron and Steel Institute, nor the Steel Stud Manufacturers Association.

Ccfss Special Edition Technical Bulletin Spring 2013, Wei-Wen Yu Center For Cold-Formed Steel Structures

CCFSS Technical Bulletins (1993 - 2020)

No abstract provided.

Flexural And Shear Behavior Of Reinforced Concrete Members Strengthened With A Discrete Fiber-Reinforced Polyurea System, Courtney E. Greene, John J. Myers

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Recent research has been conducted to evaluate the benefits provided by externally applied discrete fiber-reinforced polyurea (DFRP) coating systems. This coating was proposed to allow for ease of construction in repair-retrofit situations and to provide multihazard benefits, ranging from blast or impact fragmentation mitigation to seismic reinforcement and general strengthening. This phase of research investigated the flexural and shear reinforcement capabilities of the systems. Testing parameters included type of structural failure, polyurea, and fiber volume fraction. Additionally, the effects of the thickness of the composite system were considered. Concrete beam specimens were fabricated and coated per the designed test matrix …

Multiplatform Analysis Seismic Evaluation Of A Non-Seismically Detailed Nonlinear Rc Structure Retrofitted With Magneto-Rheological Dampers, Eric R. Lovejoy

Master's Theses

In prior research, the MR damper's dynamic characteristics are typically modeled in the MATLAB/Simulink environment. Creating a structural model with nonlinear material properties, however, may be challenging in the MATLAB/Simulink environment without approximating the material behavior and neglecting effects such as P-∆ or panel zone behavior. More behaviorally accurate models of these structures can be produced using nonlinear finite element analysis tools such as Abaqus, OpenSees or ZuesNL. These analysis tools, however, are not traditionally used to model the complex nonlinear and controllable behavior of MR dampers, nor their associated control algorithms. One solution is to facilitate communication between these …

Resistance Factors For Ductile Frp-Reinforced Concrete Flexural Members, Bashar Behnam, Christopher D. Eamon

Civil and Environmental Engineering Faculty Research Publications

To prevent damage caused by corroding reinforcement, fiber reinforced polymer (FRP) reinforcing bars have been used in place of steel in a relatively small but increasing number of structures in the civil infrastructure. A concern with the use of traditional FRP bars, however, is the resulting lack of ductility. This problem has been overcome with the development of a new generation of composite reinforcement, ductile hybrid FRP (DHFRP) bars. However, standards that address the design of DHFRP bars are unavailable, and appropriate resistance factors for the use of DHFRP reinforcement are unknown. In this study, a reliability analysis is conducted …

Reliability Analysis Of Rc Beams Exposed To Fire, Christopher D. Eamon, Elin A. Jensen

Civil and Environmental Engineering Faculty Research Publications

A procedure for conducting reliability analysis of reinforced concrete beams subjected to a fire load is presented. This involves identifying relevant load combinations, specifying critical load and resistance random variables, and establishing a high-temperature performance model for beam capacity. Based on the procedure, an initial reliability analysis is conducted using currently available data. Significant load random variables are taken to be dead load, sustained live load, and fire temperature. Resistance is in terms of moment capacity, with random variables taken as steel yield strength, concrete compressive strength, placement of reinforcement, beam width, and thermal diffusivity. A semi-empirical model is used …

Transient And Quasi-Steady Thermal Behaviour Of A Building Envelope Due To Retrofitted Cavity Wall And Ceiling Insulation, Aimee Byrne, Gerard Byrne, Anna Davies, Anthony Robinson

Articles

Accurate understanding of the thermal behaviour of building components is essential for predicting heat-ing or cooling needs and facilitates the implementation of more successful energy saving strategies and retrofits. This paper focuses on a specific measure commonly introduced through the residential energy efficiency retrofit programmes in Ireland–insulation. Traditionally, assessments of the performance of building envelopes have been based on assumed thermal resistances of the materials involved, labora-tory tests and computer modelling. The aim of the present work is to investigate the in situ thermal behaviour of a case study building and its components under transient and quasi-steady environmental conditions, comparing …

Characterization Of Impact Damage And Fiber Reinforced Polymer Repair Systems For Metallic Utility Poles, Cara Johnson

Electronic Theses and Dissertations

Previous studies have demonstrated that the behavior of fiber reinforced polymers (FRPs) bonded to metallic utility poles are governed by the following failure modes; yielding of the metallic substrate, FRP tensile rupture, FRP compressive buckling, and debonding of FRP from the substrate. Therefore, an in situ method can be devised for the repair of utility poles, light poles, and mast arms that returns the poles to their original service strength. This thesis investigates the effect of damage due to vehicular impact on metallic poles, and the effectiveness of externally-bonded FRP repair systems in restoring their capacity. Damage is simulated experimentally …

Experimental And Numerical Investigations On Bond Durability Of Cfrp Strengthened Concrete Members Subjected To Environmental Exposure, Haider Al-Jelawy

Electronic Theses and Dissertations

Fiber reinforced polymer (FRP) composites have become an attractive alternative to conventional methods for external-strengthening of civil infrastructure, particularly as applied to flexural strengthening of reinforced concrete (RC) members. However, durability of the bond between FRP composite and concrete has shown degradation under some aggressive environments. Although numerous studies have been conducted on concrete members strengthened with FRP composites, most of those studies have focused on the degradation of FRP material itself, relatively few on bond behavior under repeated mechanical and environmental loading. This thesis investigates bond durability under accelerated environmental conditioning of two FRP systems commonly employed in civil …

Monitoring For Underdetermined Underground Structures During Excavation Using Limited Sensor Data, Nader Mehdawi

Electronic Theses and Dissertations

A realistic field monitoring application to evaluate close proximity tunneling effects of a new tunnel on an existing tunnel is presented. A blind source separation (BSS)-based monitoring framework was developed using sensor data collected from the existing tunnel while the new tunnel was excavated. The developed monitoring framework is particularly useful to analyze underdetermined systems due to insufficient sensor data for explicit input force-output deformation relations. The analysis results show that the eigen-parameters obtained from the correlation matrix of raw sensor data can be used as excellent indicators to assess the tunnel structural behaviors during the excavation with powerful visualization …

Using Weigh-In-Motion Data To Determine Aggressiveness Of Traffic For Bridge Loading, Eugene J. Obrien, Bernard Enright

Articles

This paper presents results based on the analysis of an extensive database of weigh-in-motion (WIM) data collected at five European highway sites in recent years. The data are used as the basis for a Monte Carlo simulation of bridge loading by two lane traffic, both bidirectional and same-direction. Long runs of the simulation model are used to calculate characteristic bridge load effects (bending moments and shear forces), and these characteristic values are compared with design values for bridges of different length as specified by the Eurocode for bridge traffic loading. Various indicators are tested as possible bases for a “Bridge …

Reliability-Based Fatigue Assessment Of Mast-Arm Sign Support Structures, Joseph A. Diekfuss

Dissertations (1934 -)

Over the past few decades, there have been issues of poor fatigue performance (the main failure mechanism) of the welded, tube-to-transverse plate connections within sign support structures. Review of the literature has indicated that a considerable amount of research has been devoted to identifying the structural response characteristics of these signs. Others have tried to identify how these connections may be repaired, retrofitted or simply better designed to sustain longer fatigue lives. However, little attention has been given to using a systematic reliability-based approach to assess the risk of fatigue-induced fracture in these structures.

Using a reliability-based approach to solve …

The Effect Of Sensor Mass, Sensor Location, And Delamination Location Of Different Composite Structures Under Dynamic Loading, Albert Darien Liu

Master's Theses

This study investigated the effect of sensor mass, sensor location, and delamination location of different composite structures under dynamic loading. The study pertains to research of the use of accelerometers and dynamic response as a cost-effective and reliable method of structural health monitoring in composite structures. The composite structures in this research included carbon fiber plates, carbon fiber-foam sandwich panels, and carbon-fiber honeycomb sandwich panels. The composite structures were manufactured with the use of a Tetrahedron MTP-8 heat press. All work was conducted in the Cal Poly Aerospace Structures/Composites Laboratory. Initial delaminations were placed at several locations along the specimen, …

Experimental Comparison Study Of The Response Of Polycarbonate And Laminated Glass Blast Resistant Glazing Systems To Blast Loading, Joshua Calnan

Theses and Dissertations--Mining Engineering

This thesis recounts the experimental study of the dynamic response of polycarbonate blast resistant glazing systems to explosive loading through the use of triaxial load cells, pressure sensors, and a laser displacement gauge. This instrumentation captured the response of the glazing systems to blast loading over three phases of testing. The first phase of testing characterizes the load distribution around the perimeter and the second phase examines the repeatability of the results. The final phase of testing pushes the samples to failure. The results are then compared to HazL, a commonly used blast resistant glazing system analysis software tool. The …

Proceedings Of The First International Conference On Smarandache Multispace & Multistructures, Florentin Smarandache, Linfan Mao

Branch Mathematics and Statistics Faculty and Staff Publications

In recent decades, Smarandache’s notions of multispace and multistructure were widely spread and have shown much importance in sciences around the world. Organizedby Prof.Linfan Mao, a professional conference on multispaces and multistructures, named the First International Conference on Smarandache Multispace and Multistructure was held in Beijing University of Civil Engineering and Architecture of P. R. China on June 28-30, 2013, which was announced by American Mathematical Society in advance.

Development Of The Strategy To Select Optimum Reflective Cracking Mitigation Methods For The Hot-Mix Asphalt Overlays In Florida, Hamid Maherinia

Electronic Theses and Dissertations

Hot Mix Asphalt (HMA) overlay is a major rehabilitation treatment for the existing deteriorated pavements (both flexible and rigid pavements). Reflective cracking (RC) is the most common distress type appearing in the HMA overlays which structurally and functionally degrades the whole pavement structure, especially under high traffic volume. Although many studies have been conducted to identify the best performing RC mitigation technique, the level of success varies from premature failure to good performance in the field. In Florida, Asphalt Rubber Membrane Interlayers (ARMIs) have been used as a RC mitigation technique but its field performance has not been successful. In …

Analytical And Experimental Study Of Monitoring For Chain-Like Nonlinear Dynamic Systems, Bryan Paul

Electronic Theses and Dissertations

Inverse analysis of nonlinear dynamic systems is an important area of research in the eld of structural health monitoring for civil engineering structures. Structural damage usually involves localized nonlinear behaviors of dynamic systems that evolve into different classes of nonlinearity as well as change system parameter values. Numerous parametric modal analysis techniques (e.g., eigensystem realization algorithm and subspace identification method) have been developed for system identification of multi-degree-of-freedom dynamic systems. However, those methods are usually limited to linear systems and known for poor sensitivity to localized damage. On the other hand, non-parametric identification methods (e.g., artificial neural networks) are advantageous …

Anchored Sheet Pile Wall Design In Expansive Soils, Ömer Bilgin, Eman Mansour

Civil and Environmental Engineering and Engineering Mechanics Faculty Publications

Expansive soils cause damage to civil engineering structures in various parts of the world, because they swell when absorb water and shrink when dry out. Due to swelling pressures, retaining walls can be subjected to additional lateral pressures causing increased wall deformations and bending moments. Anchor forces can also increase, if the walls are anchored. When expansive soils are present behind retaining walls, swell pressures should also be considered during design in addition to the traditional lateral earth pressures. This study proposes a method to predict potential swell pressures acting on retaining walls for use in design of these walls. …

The Effects Of Assumption On Subspace Identification Using Simulation And Experiment Data, Yoonhwak Kim

Electronic Theses and Dissertations

In the modern dynamic engineering field, experimental dynamics is an important area of study. This area includes structural dynamics, structural control, and structural health monitoring. In experimental dynamics, methods to obtain measured data have seen a great influx of research efforts to develop an accurate and reliable experimental analysis result. A technical challenge is the procurement of informative data that exhibits the desired system information. In many cases, the number of sensors is limited by cost and difficulty of data archive. Furthermore, some informative data has technical difficulty when measuring input force and, even if obtaining the desired data were …