Environmental Engineering Commons^™

Impact Of Macropores And Gravel Outcrops On Phosphorus Leaching At The Plot Scale In Silt Loam Soils, Derek M. Heeren, Garey A. Fox, Chad Penn, Todd Halihan, Daniel E. Storm, Brian Haggard

Department of Agricultural and Biological Systems Engineering: Faculty Publications

In response to increased nutrient loads in surface waters, scientists and engineers need to identify critical nutrient source areas and transport mechanisms within a catchment to protect beneficial uses of aquatic systems in a cost-effective manner. It was hypothesized that hydrologic heterogeneities (e.g., macropores and gravel outcrops) in the vadose zone play an integral role in affecting flow and solute transport between the soil surface and shallow alluvial aquifers. The objective of this research was to characterize phosphorus (P) leaching through silt loam soils to alluvial gravel aquifers in the floodplains of the Ozark ecoregion at the plot scale. Solute …

Building Information Modelling In Ireland 2017, Barry Mcauley, Alan Hore, Roger West

Reports

BIM is perhaps the most topical issue in construction throughout the world at present, as it is associated with solving so many of the present concerns in our industry.

Our lack of housing, shortage of skilled workers, poor document management, overrunning project budgets and sustainability challenges are just a few of the challenges that BIM promises to assist in solving.

The increasing importance of “digitisation” to modern construction and engineering businesses is becoming more apparent as more and more clients are explicitly asking for BIM in the design and delivery of new facilities and infrastructure.

This report provides a snapshot …

Influence Of Activated Carbon Surface Oxygen Functionality On Elemental Mercury Adsorption From Aqueous Solution, Emily K. Faulconer, David W. Mazyck

Publications

Mercury (Hg), though naturally occurring, is a toxic element. Exposure to various forms of mercury can be harmful for humans and ecosystems. Mercury-contaminated wastewater can be treated using activated carbon to adsorb the mercury, allowing for safe discharge. Wet chemical oxidation of activated carbon was performed to enhanced surface oxygen functionality, with the objective of enhancing aqueous ionic (Hg(II)) and elemental (Hg(0)) mercury adsorption. Characterization of the modified carbons included nitrogen adsorption-desorption, elemental analysis, point of zero charge, and total acidity titration. The concentration and identity of the modifying reagent influenced the characteristics of the carbons, including the surface oxygen …

Quantifying The Impact Of Truck Only Lanes On Vehicular Emissions On A Limited-Access Highway, Edward Chee Tang

Master's Theses

This thesis seeks to estimate CO₂ emissions on a portion of the U.S. 101 highway in San Luis Obispo County before and after construction of a truck only lane on the Cuesta Grade. Towards that aim, the microsimulation software, VISSIM, was used in conjunction with the Environmental Protection Agency’s emissions model, MOVES. The microsimulation model was calibrated and validated against historical and present traffic volumes obtained from Caltrans with good results using several validation measures. It was found that CO₂ emissions did decrease between 1998 and 2012 (pre and post lane addition), but this effect was shown to …

Geometry-Based Mass Grading Of Mango Fruits Using Image Processing, M. A. Momin, Md Towfiqur Rahman, M. S. Sultana, C. Igathinathane, A. T. M. Ziauddin, T. E. Grift

Department of Agricultural and Biological Systems Engineering: Faculty Publications

Mango (Mangifera indica) is an important, and popular fruit in Bangladesh. However, the post-harvest processing of it is still mostly performed manually, a situation far from satisfactory, in terms of accuracy and throughput. To automate the grading of mangos (geometry and shape), we developed an image acquisition and processing system to extract projected area, perimeter, and roundness features. In this system, images were acquired using a XGA format color camera of 8-bit gray levels using fluorescent lighting. An image processing algorithm based on region based global thresholding color binarization, combined with median filter and morphological analysis was developed …

Regulatory Barriers To Approval Of New Technologies For Small Drinking Water Systems, Deanna T. Ringenberg

Department of Environmental Engineering: Theses and Other Student Research

Small drinking water systems face different challenges than large drinking water systems. Innovative technologies can provide cost and reliability benefits to small systems, but new technologies are not frequently considered. One important barrier to the implementation of new technologies is obtaining state drinking water agency approval.

To identify specific state regulatory barriers, a survey including sixteen questions was sent to the 49 state agencies. The survey included questions regarding their acceptance programs, experiences with new technologies, barriers, data needs for technology approval, and interest in a shared approach for acceptance of new technologies. The survey was sent in 2015 and …

Diplomacy Lab Provides Term-Length Group Projects Integrating Policy Analysis And Liberal Arts Into The Traditional Engineering Classroom, Daniel B. Oerther

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Science in diplomacy, the use of trained scientist to inform and support foreign policy objectives, has been a part of U.S. foreign policy since the time of Benjamin Franklin. The Diplomacy Laboratory project, a public-private partnership, allows the Department of State to 'course source' projects to seek input from universities and to recruit talented students to consider careers in diplomacy. This paper provides a summary of a case study using a DipLab project as part of a term-length, writing assignment in courses for undergraduate and graduate environmental engineering students. An overview of DipLab and suggested best practices to integrate DipLab …

Reducing Costs While Maintaining Learning Outcomes Using Blended, Flipped, And Mastery Pedagogy To Teach Introduction To Environmental Engineering, Daniel B. Oerther

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

As part of a cost-savings initiative, an existing course of 'introduction to environmental engineering' offered using a 'traditional' format of didactic class meetings supplemented with hands-on laboratory sessions, was changed significantly. The 'modified' format uses 'blended', 'flipped', and 'mastery' approaches to teach "2601: Fundamentals of Environmental Engineering" to approximately 60 sophomores pursuing baccalaureate degrees in environmental, civil, or architectural engineering, each semester. This paper presents a summary of the results from eight course offerings over a period of four years to more than 450 total students. Assessments included student grades; open-ended invitations for anonymous feedback at the end of each …

Using Nursing Theory To Improve The Teaching Of Engineering Practice, Daniel B. Oerther

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Engineering education includes both classroom training in sciences and professional skills as well as learning-through-doing to integrate practice and engineering design into the future licensed Professional Engineer (PE). In a similar manner, nursing education includes both classroom training in sciences and professional skills as well as learning through doing to integrate practice and caring into the future licensed Registered Nurse (RN). From the mid-19th century until modern day, the fields of environmental engineering and community health nursing have worked side-by-side to prevent disease while promoting health and wellness. This paper provides a synthesis of previously published case studies by the …

Sensor System, Implantable Sensor And Method For Remote Sensing Of A Stimulus In Vivo, Eric H. Ledet, Rebecca A. Wachs, Keegan Paul Cole, David Fiorella

Department of Agricultural and Biological Systems Engineering: Faculty Publications

A sensor system for sensing a stimulus in vivo includes an implantable sensor. The sensor comprises a passive resonator circuit having a resonant frequency and including at least a pair of generally parallel spirally wound unconnected conductive coils sandwiching a layer of solid dielectric material that manifest a change in property affecting the resonant frequency in response to application of the stimulus to the layer. A resonant frequency of the sensor is modulated by altering the spacing or gap between the coils or altering the overlapping area of the coils. The sensor is energized through application of radio frequency energy …

2017 Spring Engr333 Project Final Report (Section A), Devin Auld, Scott Bokach, Joshua Bronner, Alex Meador, Ryan Hoek, Robert Lanser, Matthew Lenko, Elliot Slenk, Brendan Biesboer, Kyle Mailhot, Nate Zylstra, Jonah Engel, Rich Floro, Björn Krebs, Ethan Postmus, Cameron Bell, Caleb Bieske, Chris Griffin, Bernice Portugal, Ryan Beezhold, Dillon Carhuff, Ian Mcclaskie, Jared Vanderklay, Rounak Chatterjee, Toby Dalla Santa, Jenny Haney, Joel Hoskins, Caleb Senyshyn

ENGR 333

The objective of ENGR-333-A was to develop a well-defined, bottom-up energy demand model for the energy consumption of the dormitories on Calvin College’s campus for each year of the past decade within an accuracy of ± 2%.

2017 Spring Engr333 Project Final Report (Section B), Daniel Dick, Nathan Swaim, Jonathan Sager, Ellen Reidy, Jordan Swets, Joel Van Dyke, Connor Macdonald, Josiah Markvluwer, Justin Rohlicek, John Lee, Zach Mouw, Daniel Wharton, Sam Hanover, Jay Noyola, Adam Christenson, Scott Stamper, Aaron Tucker, Bethany Waanders, Joel Schaefer, Maddie Collins, Matthew Cok, Philip Kim, Steve Vanden Berg

ENGR 333

The Physical Education Complex is located in the North-end of Calvin College’s campus, and supports many athletic, academic, event and recreational functions. Due to its heavy use, the complex contributes 20% of the College’s electricity consumption. Monetarily, this equated to electricity costs of about $385,000 last year. With these financial implications, the College is searching for ways to reduce the cost. While there is little to no room for electricity cost rate reductions, there is opportunity for improvement through the implementation of more efficient components. However, the sources of electricity demand are largely unknown. Our objective is to develop a …

The Effect Of Diffusive Transport On Mineral Carbonation In Geologic Carbon Sequestration, Wei Xiong

McKelvey School of Engineering Graduate Student Theses & Dissertations

Geologic carbon sequestration (GCS) is an effective method to mitigate environmental problems due to excessive anthropogenic CO2 emissions. It involves injecting supercritical CO2 into deep geologic formations in which CO2 will ultimately be converted to solid carbonate minerals. Basalt is a promising host rock that is rich in the divalent cations Ca, Mg and Fe that are important for mineral trapping of CO2. Fractures and pores in basalt reservoirs provide substantial surface area for geochemical reactions during carbon sequestration. The transport in fractures and pores is controlled by diffusion. The coupling of diffusive transport and geochemical reactions leads to carbonate …

Sub 2 Nm Particle Characterization In Systems With Aerosol Formation And Growth, Yang Wang

McKelvey School of Engineering Graduate Student Theses & Dissertations

Aerosol science and technology enable continual advances in material synthesis and atmospheric pollutant control. Among these advances, one important frontier is characterizing the initial stages of particle formation by real time measurement of particles below 2 nm in size. Sub 2 nm particles play important roles by acting as seeds for particle growth, ultimately determining the final properties of the generated particles. Tailoring nanoparticle properties requires a thorough understanding and precise control of the particle formation processes, which in turn requires characterizing nanoparticle formation from the initial stages. The knowledge on particle formation in early stages can also be applied …

Supraspinatus Tendon Micromorphology In Individuals With Subacromial Pain Syndrome, Federico Pozzi, Amee L. Seitz, Hillary A. Plummer, Kira Chow, Gregory R. Bashford, Lori A. Michener

Department of Agricultural and Biological Systems Engineering: Faculty Publications

Study Design: Cross-sectional cohort. Introduction: Tendon collagen organization can be estimated by peak spatial frequency radius (PSFR) on ultrasound images. Characterizing PSFR can define the contribution of collagen disruption to shoulder symptoms.

Purpose of the Study: The purpose of this was to characterize the (1) supraspinatus tendon PSFR in participants with sub acromial pain syndrome (SPS) and healthy controls; (2) PSFR between participants grouped on a tendon visual quality score; and (3) relationship between PSFR with patient-reported pain, function, and shoulder strength.

Methods: Participants with SPS (n ¼ 20) and age, sex, and arm-dominance matched healthy controls (n ¼ 20) …

2017 Spring Engr333 Seminar Presentation, Jonah Engel, Rich Floro, Björn Krebs, Ethan Postmus, Brendan Biesboer, Kyle Mailhot, Nate Zylstra, Ryan Beezhold, Dillon Carhuff, Ian Mcclaskie, Jared Vanderklay, Rounak Chatterjee, Toby Dalla Santa, Jennifer Haney, Joel Hoskins, Caleb Senyshyn, Alex Meador, Scott Bokach, Devin Auld, Joshua Bronner, Elliot Slenk, Matthew Lenko, Robert Lanser, Ryan Hoek, Cameron Bell, Caleb Bieske, Chris Griffin, Bernice Portugal, Sam Hanover, Dan Wharton, Jay Noyola, Zachary Mouw, John Lee, Daniel Dick, Jonathan Sager, Nathan Swaim, Ellen Reidy, Jordan Swets, Joel Van Dyke, Connor Macdonald, Josiah Markvluwer, Justin Rohlicek, Adam Christensen, Scott Stamper, Aaron Tucker, Bethany Waanders, Joel Schaefer, Maddie Collins, Matthew Cok, Philip Kim, Steve Vanden Berg

ENGR 333

File for student presentation, given by students in the Spring 2017 class of ENGR333.

College Of Engineering Senior Design Competition Spring 2017, University Of Nevada, Las Vegas

Fred and Harriet Cox Senior Design Competition Projects

Part of every UNLV engineering student’s academic experience, the senior design project stimulates engineering innovation and entrepreneurship. Each student in their senior year chooses, plans, designs, and prototypes a product in this required element of the curriculum. A capstone to the student’s educational career, the senior design project encourages the student to use everything learned in the engineering program to create a practical, real world solution to an engineering challenge. The senior design competition helps focus the senior students in increasing the quality and potential for commercial application for their design projects. Judges from local industry evaluate the projects on …

Fluid Isolator, Purdue Ect Team

ECT Fact Sheets Archive

The reliability of concrete infrastructure is vital to ensuring daily life, as well as commerce, can progress without interruption. From the pavement of interstate highways to the driveways and sidewalks in a local neighborhood, concrete is expensive to install and often even more expensive, and intrusive, when it needs to be replaced. Unfortunately, to maintain functionality in winter climates concrete is heavily exposed to deicing salts. This not only affects the roads, driveways, and sidewalks where salt is applied directly, but many other areas such as parking and residential garages where vehicles (and people) will track salt along with water …

Netpoint®, Purdue Ect Team

ECT Fact Sheets Archive

The vast majority of construction scheduling software uses a combination of spreadsheets and Gantt charts for developing and depicting Critical Path Method (CPM) schedules. While this paradigm works for the expert scheduler, it is not conducive to collaboration, and it is prohibitively difficult for non-scheduling experts to understand.

NetPoint® provides a dynamic, visual interface conducive to touch and gestural input. Activities are drawn directly on a time-scale and may be placed on the same row or arranged automatically using codes or the WBS. Such control of the presentation makes it easier to communicate the plan to any type of audience. …

Method For The Production Of Substituted Polysaccharides Via Reactive Extrusion, Milford Hanna, Pratik Bhandari

Department of Agricultural and Biological Systems Engineering: Faculty Publications

A reactive extrusion process for the production of substituted polysaccharides, in particular, cellulose acetate, starch acetate, carboxymethyl cellulose, and carboxymethyl starch.

The present application claims the benefit of PCT/ US20111059785 filed on Nov. 8, 2011, which claimed the benefit of U.S. provisional application 611411,521, filed on Nov. 9, 2010, U.S. provisional application 611411,992, filed on Nov. 10, 2010, and U.S. provisional application 611472, 748, filed on Apr. 7, 2011, each of which is which is incorporated herein by reference in its entirety.

The production of substituted polysaccharides such as starch and cellulose acetates and carboxymethylated starches and celluloses have typically …