Construction Engineering and Management Commons^™

Decision-Making Through Sustainability, F. Pardo-Bosch, A. Aguado

International Symposium on Hydraulic Structures

From immemorial time, dams have contributed significantly for the progress of civilizations. For this reason, nowadays, there is a vast engineering heritage. Over the years, these infrastructures can present some ordinary maintenance issues associated with their normal operation or with ageing processes.

Normally, these problems do not represent an important risk for the structure, but they have to be attended. To do it, owners of dams have to finance many ordinary interventions. As it is impossible to carry out all of them at the same time, managers have to make a decision and select the most “important” ones. However, it …

An Investigation In Construction Cost Estimation Using A Monte Carlo Simulation, Jeffrey D. Buchholtz

Theses and Dissertations

The Air Force estimates military construction (MILCON) costs early in a project’s development as a part of the funding approval process. However, many of the initial cost estimates deviate significantly more than expected from the actual project costs, hindering funding allocation efforts. There is a need for improved estimation techniques. This research examines a cost estimation model for the initial programming stages of a project when only general scope information is available.

This study develops a Monte Carlo simulation based on historical construction cost data to predict project costs base on facility type. For a given facility type, the research …

Corrosion Of Steel In Concrete And Its Prevention In Aggressive Chloride-Bearing Environments, Luca Bertolini, Maddalena Carsana, Matteo Gastaldi, Federica Lollini, Elena Redaelli

International Conference on Durability of Concrete Structures

This keynote paper deals with the durability of reinforced concrete (RC) structures exposed to aggressive environments characterized by high concentration of chloride ions, namely, marine environments or the use of de-icing salts. The mechanism of chloride-induced corrosion of steel in concrete is introduced, and its influence on the service life of RC structures is analyzed. Factors affecting the time to corrosion initiation are described with regard to both concrete properties and environmental exposure conditions. Design approaches available for achieving durability targets associated with the design service life are analyzed, focusing on studies carried out by the authors in recent years …

Mat-701: Predicting The Compressive Strength Of Ultra-Lightweight Concrete By An Artificial Neural Network, Jordan Ouellet, Jean-Luc Martel, Claudiane Ouellet-Plamondon, Alan Carter

Canadian Society for Civil Engineering

Ultra-lightweight concrete (ULWC) has potential applications for floating structures and architectural elements because of its dry density coming in at under 1000 kg/m3. The objective was to develop an artificial neural network (ANN) to aid the ULWC designer according to his needs. Boundary conditions were set for each material and 13 constraints based on the water binder ratio, density, air content, binder and aggregate content. The ANN predicted the compressive strength with a comfortable margin of error, with the gap encountered being attributed to variability in workability. Precise constraints and boundary conditions are needed to ensure a lower variability in …

Mat-702: Mechanical Behaviour Of Ultra-High Performance Concrete Obtained With Different Concrete Constituents And Mix Designs, Mahmoud Sayed-Ahmed, Khaled Sennah, Moulay Youssef Monsif

Canadian Society for Civil Engineering

This research investigates the mechanical behaviour for the Ultra-High Performance Concrete (UHPC) and UltraHigh Performance Fiber Reinforced Concrete (UHPFRC). UHPC and UHPFRC are designed to be self-consolidated concrete that level itself without mechanical vibration due to its highly flowability and moderate viscosity. UHPFRC is used as joint-fill cementitious materials for the connections of prefabricated bride elements and systems used for the Accelerated Bridge Construction and rapid bridge replacement. The main concrete constituents of such materials consist from: binders (cement), powders (fillers), liquids (additives), water, and fibers. Hence, the mixture proportion design should follow a densified mixture design algorithm to densify …

Mat-704: Resistance Of Concrete Incorporating Portland Limestone Cement To Sulfuric Acid, Mahmud Amin, Mohamed T. Bassuoni

Canadian Society for Civil Engineering

Concrete has long been the most popular choice for constructing key infrastructural elements such as sewer pipes, water treatment facilities, industrial floors and foundations. However, many field cases from all around the world have shown that concrete elements in these environments are severely damaged due to biogenic and/or chemical sulfuric acid attack. Since high alkalinity is required for the stability of the cementitious matrix, concrete is highly prone to acid attacks, which decalcify and disintegrate the hydrated cement paste to various levels based on exposure conditions and type of concrete. Numerous studies have been conducted to enhance the durability of …

Mat-705: Improving The Efficiency Of Zinc Sacrificial Anodes In Repaired Concrete, Ahmed G. Bediwy, Mohamed T. Bassuoni, Martin Beaudette

Canadian Society for Civil Engineering

Zinc sacrificial anodes are considered an effective and economical method to prevent the electrochemical corrosion of steel bars by providing cathodic current to bars, which can provide corrosion protection at low galvanic current densities in the range of 0.2 to 2 mA/m2. Sacrificial anodes are commonly used in RC structures particularly in bridge decks to mitigate a critical phenomenon that occurs in the original concrete beside the repaired patches, which is known as the ‘halo effect’. One of the key factors affecting the efficacy of zinc anodes is the resistivity of concrete or cementitious repair material in which these anodes …

Mat-707: Development Of Enhanced Test Methods To Evaluate Alkali-Silica Reaction In Concrete, Noura Sinno, Medhat Shehata

Canadian Society for Civil Engineering

The research presented in this paper studies the effect of sample geometry and temperature on expansion due to alkali-silica reaction (ASR) in concrete. Expansions of cubes and cylinders are compared to those of the standard prisms. Control samples, samples with fly ash (FA) and others with slag are investigated at two temperatures, 38°C and 60°C. At 38°C, results showed that smaller samples have higher expansion at early ages. However, larger samples such as cubes and cylinders seem to reach higher expansion compared to prisms after 32 weeks for both control and samples with fly ash. In addition, the results showed …

Mat-708: Monitoring The Corrosion Process Of Reinforced Concrete Flat Slab-Column Connection, Mahmoud E. Said, Amgad Hussein, Assem A. A. Hassan

Canadian Society for Civil Engineering

The corrosion of the steel reinforcement embedded in a two-way reinforced concrete flat slab around the column stub area was investigated in this study, which aimed to studying the effect of corrosion on the shear punching behavior. Two square flat slab-column connections were cast, the flat slab dimension was 1900 mm × 1900 mm × 150 mm, and the column dimensions was 250 mm × 250 mm. A specific delaminated area was corroded around the column stub to emphasize the effect of corrosion around punching area. The corrosion reached two levels of mass loss uniformly over that specified area: 0% …

Mat-711: Utilization Of Recycled Crumb Rubber In Structural Self-Consolidating Concrete, Mohamed K. Ismail, Assem A. A. Hassan, Madolyn A. Lundrigan

Canadian Society for Civil Engineering

The present work evaluates the impact of using recycled crumb rubber (CR) as a partial replacement of fine aggregate on the fresh and mechanical properties of concrete composite, especially when self-consolidating concrete is used. In this study, seven mixtures containing various amounts of fine CR (0-30% by volume of sand) were tested. The fresh properties tests included flowability, passing ability, and segregation resistance. On the other hand, the mechanical properties tests included compressive strength, modulus of elasticity, splitting tensile strength, and flexural strength. The results indicated that although increasing the CR replacement decreased the fresh and mechanical properties of concrete, …

Mat-712: Microstructural Investigations On The Self-Healing Ability Of Engineered Cementitious Composites Incorporating Different Mineral Admixtures, Ahmed Alyousif, Khandaker M. Anwar Hossain, Mohamed Lachemi, Mustafa Sahmaran

Canadian Society for Civil Engineering

The present study investigates the impacts that self-healing has on the microstructure characteristics of microcracked Engineered Cementitious Composites (ECC). These have two contrasting maturity levels and, furthermore, they involve three varying mineral admixtures that have very different chemical constituents. The impact of self-healing on the transport characteristics was examined by employing rapid chloride permeability tests (RCPT). The findings indicated that, if the appropriate mineral admixture type and conditioning were chosen, it would be possible to enhance the majority of the chloride ion penetrability levels following a 30-day period of water curing. As a result, the majority of the findings were …

Mat-713: Evaluation Of Ndt Techniques For Concrete Bridge Decks Using Fuzzy Analytical Hierarchy Process, Tarek Omar, Moncef L. Nehdi

Canadian Society for Civil Engineering

Considering the colossal backlog of deteriorating bridges, transportation agencies need to systematically evaluate bridge deck conditions in order to optimize the timing, scope, and approach of preventive maintenance, repair, and replacement. Over the last few years, there have been growing interest among bridge infrastructure stakeholders in using non-destructive methodologies for bridge inspection, evaluation, and maintenance. Nondestructive testing (NDT) techniques can provide needed information about the “under-the-surface” deteriorated condition of bridge decks. This paper examines the most common NDT technologies for assessing bridge decks. Each technology was rated based on five performance measures: capability to detect subsurface defects, speed of data …

Mat-714: Condition Assessment And Deterioration Prediction Tools For Concrete Bridges: A New Look, Tarek Omar, Moncef L. Nehdi

Canadian Society for Civil Engineering

Structural problems created by corrosion, ageing, aggressive environments, material defects and unforeseen mechanical or seismic loads can compromise the serviceability and safety of bridges. The importance of an effective bridge-management system (BMS) cannot be overstated, especially in light of the recent collapse of bridges in North America and elsewhere. Several technologies are available for assessing the condition of concrete bridges and a number of deterioration models are used to predict future bridge conditions and estimate associated funding requirements. This paper critically reviews the different available condition assessment and deterioration prediction approaches for concrete bridges. The potential applications of condition assessment …

Mat-716: Green Sidewalks Using Sustainable Two-Stage Concrete, Manal F. Najjar, Ahmed M. Soliman, Tareq M. Azabi, Moncef L. Nehdi

Canadian Society for Civil Engineering

Two-stage concrete (TSC) is a special type of concrete, which has a high potential for use in sidewalk construction owing to its high volume stability. TSC is characterized by its high coarse aggregate content. Hence, using recycled solid waste materials as a coarse aggregate will increase TSC sustainability, while providing a cost-effective alternative to natural aggregates. Aggregates are pre-placed in TSC. Hence, water absorption by recycled concrete aggregates and the associated rheology problems do not exist in TSC. This study explores the performance of green TSC sidewalks incorporating recycled concrete aggregates (RCA) and crumb rubber from scrap tires. Mechanical properties …

Mat-719: Investigation Of Grouted Precast Concrete Wall Connections At Subfreezing Conditions, Douglas James Provost-Smith, Mohamed Elsayed, Moncef L. Nehdi

Canadian Society for Civil Engineering

The effect of exposing grouted precast wall connections to subfreezing curing temperatures at early-age was explored in this study. In cold weather construction, heating of the surrounding environment of grouted precast wall connections is usually conducted for short periods of time. Hence, subfreezing conditions can affect the strength of the grout and the bond strength of the connection, which can ultimately compromise the integrity of the structure. In this study, grout specimens typical of that used in precast wall construction were cured at ambient conditions for one day, and then placed in an environmental chamber at subfreezing temperatures (-10°C and …

Mat-721: Alkali-Silica Reactivity In Southwestern Ontario Aggregates, Ahmed R. Suleiman, Aaron Jobst, Moncef L. Nehdi

Canadian Society for Civil Engineering

Alkali-silica reaction (ASR) occurs between alkalis in concrete and reactive silica in aggregates. This reaction results in the formation of alkali-silica gel, which fills the pore space in the cementitious matrix, leading to expansion and damage. Reactive aggregates that can cause this type of damage were identified in different locations in Southwestern Ontario. X-Ray diffraction and petrographic analysis were used to investigate the type of reactive minerals in such aggregates. In addition, the effect of using different types of cement replacement-materials, including crushed limestone powder, fly ash, silica fume, and nano-silica on ASR were investigated in cement mortars incorporating the …

Mat-722: Effect Of Fiber Orientation On The Behavior Of Cfrp Confined Concrete Cylinders, Ahmed Sulaiman, Husham Almansour, Hassan Aoude

Canadian Society for Civil Engineering

This paper presents the results of an ongoing experimental investigation examining the effect of fiber orientation and stacking sequence on the behavior of FRP-confined concrete. As part of the experimental study, 100 mm x 200 mm concrete cylinders were jacketed with carbon fiber reinforced polymer (CFRP) sheets and tested under pure axial compressive loading. The specimens were confined using various CFRP stacking sequences, with fibers oriented at 0⁰, 90⁰, and ±45⁰. Furthermore, within each stacking sequence, the numbers of layers was varied from 4 to 8 to examine the effect of number of plies on the behavior of the FRP-confined …

Mat-723: Bond Behaviour Of Grouted Connections Under Monotonic Tensile Loads, Mohamed Elsayed, Douglas James Provost-Smith, Moncef L. Nehdi, Osama Eissa

Canadian Society for Civil Engineering

Grouted bar-in-conduit connections are versatile connections widely used in the precast concrete construction. In precast load bearing wall structures, two vertical wall panels are connected by a reinforcing bar, which is projected from one panel and grouted into a sleeve placed in the other. The main function of the ties is to resist tension induced by in-plane and out-of-plane straining actions and to provide ductility to the wall assembly through the yielding of the reinforcement. Limited information is currently available on the behaviour of such connections. This paper presents the findings of an investigation conducted to investigate the behaviour of …

Mat-724: Low Energy Concrete, Al-Shimaa Abudllatif, Aya-Tallah Elkharbotly, Basma El-Bassiouny, Mennatallah El-Bassiouny, Yousef Amin, Amr Fathy, Mohamed N. Abou-Zeid, Ezzat H. Fahmy

Canadian Society for Civil Engineering

The escalating demand on energy consumption as well as the scarcity of non renewable energy resources represents a major concern worldwide. Hence, efforts are being exerted to resort to lower energy alternatives in almost all aspects of life. Portland cement concrete has been known as an energy intensive material that emits large amount of CO2 during its various stages of manufacturing. While concrete has been classified over the decades based on its performance, it has seldom been assessed and evaluated based on its embodied energy.

This work aims at evaluating concrete mixtures based on energy and CO2 emission together with …

Mat-725: Self Leveling Mortar: Why And How?, Ahmed Hassanein, Eman Shalaby, Omar Amer, Reem Ahmed, Sherif Orban, Amr Fathi, Yousef Abu Gharieb, Mohamed N. Abouzeid, Ezzat H. Fahmy

Canadian Society for Civil Engineering

Concrete floors can develop faults over time which can cause damage thus hindering smooth transportation, industrial aspects and some residential drawbacks. In addition, flaws and cracks are known to progress into more serious damage with time and use. Self leveling mortar has been used on a relatively limited scale worldwide to allow for more even, higher performance and easy-to-apply flooring. However, there has been little information available with respect to their use and best practices.

The primary focus of this work is to prepare mortar that possesses self-levelling flow characteristics. Hence, several mixtures have been designed using various constituents with …