A Probabilistic Casualty Model To Include Injury Severity Levels In Seismic Risk Assessment,
2020
Clemson University
A Probabilistic Casualty Model To Include Injury Severity Levels In Seismic Risk Assessment, Weichiang Pang, S. Majdalaweyh, A. Safiey, K. Rokneddin, S. Prabhu, M. Javanbarg, E. Ziaei
Publications
Despite the increasing adoption of Performance-Based Earthquake Engineering (PBEE) in seismic risk assessment and design of buildings, earthquakes resulted in around 1.8 million injuries (three times the number of fatalities) over the past two decades. Several existing PBEE-based methodologies use rudimentary models that may not accurately estimate earthquake-induced casualties. Even when models are suitable for predicting the total number of fatalities and critical injuries, they may fail to adequately differentiate between different levels of injury severity. This paper draws attention to the importance of extending the seismic casualty assessment method by broadening the perspective on injury severity. To this cause, …
Ground Motion Duration Effects On The Seismic Risk Assessment Of Wood Light-Frame Buildings,
2020
Clemson University
Ground Motion Duration Effects On The Seismic Risk Assessment Of Wood Light-Frame Buildings, Weichiang Pang, A. Safiey, S. Majdalaweyh, E. Ziaei, K. Rokneddin, M. Javanbarg
Publications
Wood construction comprises a large portion of building stocks of several countries across the globe with high preparedness for earthquakes including Japan, Canada, and the United States. Built environments of these countries are prone to long-duration ground shakings due largely to the proximity of subduction faulting systems. However, the current seismic design requirements do not adequately emphasize this key feature of ground motions. This study evaluates the impact of long-duration ground motions on seismic risk characteristics of code-conforming wood lightframe buildings. To this end, a study matrix of wood light-frame buildings is developed incorporating with two different heights (i.e., 1-story …
Implementation Of An Open-Source Digital Image Correlation Software For Structural Testing,
2020
California Polytechnic State University, San Luis Obispo
Implementation Of An Open-Source Digital Image Correlation Software For Structural Testing, Nicole V. Buck
Master's Theses
This thesis investigates the appropriateness of a simplified, open-source digital image correlation (DIC) software for use in quasi-static, structural testing utilizing two-dimensional (2D) DIC measurements. DIC is a non-contact optical measurement technique that uses computer vision to track unique attributes on the surface of an object. For structural testing, traditional instrumentation such as displacement sensors and strain gages are impractical for full field measurements due their limited ability to capture large amounts of data. However, over the past decade, DIC has proven a successful method for full-field kinematics measurements, making it an appealing tool for collecting high densities of accurate …
The Impact Of Metal Pipe Materials, Corrosion Products, And Corrosion Inhibitors On Antibiotic Resistance In Drinking Water Distribution Systems,
2020
Marquette University
The Impact Of Metal Pipe Materials, Corrosion Products, And Corrosion Inhibitors On Antibiotic Resistance In Drinking Water Distribution Systems, Lee Kimbell, Yin Wang, Patrick J. Mcnamara
Civil and Environmental Engineering Faculty Research and Publications
Drinking water distribution systems (DWDS) are unique engineering environments that are important routes for the acquisition and dissemination of antibiotic resistance. Antibiotic-resistant bacteria (ARB) and antibiotic resistance genes (ARGs) in drinking water pose risks to human and environmental health. Metals are known stressors that can select for antibiotic resistance. The objective of this review was to assess the state of knowledge regarding the impact of metal pipe materials, corrosion products, and corrosion inhibitors on the prevalence of antibiotic resistance in DWDS. ARGs and mobile genetic elements (MGEs) have been detected in full-scale DWDS in concentrations ranging from ~ 101 …
Bs News September/October,
2020
Technological University Dublin
Hybrid Passive Control System For Seismic Response Mitigation Of Steel Frame Structures,
2020
Universiti Malaya
Hybrid Passive Control System For Seismic Response Mitigation Of Steel Frame Structures, Mohammad Hossein Mehrabi
Student Works (2020-2029)
Large vibration forces such as from seismic excitations can cause structural damage and structural collapse in the case of intense earthquakes. A large number of novel methods and of these techniques has weaknesses and strengths. Several control devices demonstrate a two-step mechanism in which the structure's stiffness is initially raised, and then the of the first vibration period down to a region where the structural response is significantly increased. The main aim of this thesis is to propose a hybrid passive control system comprises of two phases for the seismic retrofit of moment-resisting steel frames. The first phase is a …
Modeling Strategies For Structures Using Ductile Concrete Materials In Seismic Applications,
2020
New Jersey Institute of Technology
Modeling Strategies For Structures Using Ductile Concrete Materials In Seismic Applications, Hasan Tariq
Dissertations
No abstract provided.
Numerical Study Of Paraffin Wax Melting In A Cavity With A Gradient Of Hot Wall Inclination,
2020
Teknik Mesin, Sekolah Tinggi Teknologi Ronggolawe, Jawa Tengah 58315, Indonesia
Numerical Study Of Paraffin Wax Melting In A Cavity With A Gradient Of Hot Wall Inclination, Agus Dwi Korawan
Makara Journal of Technology
The melting of a phase change material (PCM) in a cavity with a gradient of hot wall inclination was simulated numerically using five models, namely, Model-A, Model-B, Model-C, Model-D, and Model-E with gradients of −2, −4, ∞, 4, and 2, respectively. The PCM was paraffin wax, which was melted using an enthalpy porosity technique with a pressure-based method. Model-A was found to be the best model. For the completion of the melting process, the models were assigned with the liquid fraction of 1. Model-A required the shortest time, followed by Model-B, Model-C, Model-E, and Model-D, respectively. Compared with Model-C, Model-A …
St. Mary And St. Anne Cathedral, Cork: An Optimum Heating Solution For Heritage Buildings?,
2020
Department of Civil Structural and Environmental Engineering, Museum Building, Trinity College, University of Dublin, Dublin, Ireland
St. Mary And St. Anne Cathedral, Cork: An Optimum Heating Solution For Heritage Buildings?, Christopher Shiell, Roger P. West
Civil Engineering Research in Ireland 2020
Cathedrals and most churches are characterised by having large internal, undivided spaces and permeable building envelopes. They are often used little, intermittently, but predictably and, in spite of the fact that they are unique in still being largely used for the purpose for which they were built many centuries ago, they are now often used for additional purposes, for which they were never designed. These uses include concerts, graduation ceremonies, filming and a host of other uses all of which require a level of thermal comfort not envisaged by the original builders. Research was undertaken by the authors into the …
Challenges And Opportunities To Deep Retrofitting Of Traditional Fabric Buildings To Achieve Nearly Zero Energy Building (Nzeb),
2020
MaREI Centre for Energy, Climate and Marine, Ryan Institute & School of Engineering, National University of Ireland, Galway
Challenges And Opportunities To Deep Retrofitting Of Traditional Fabric Buildings To Achieve Nearly Zero Energy Building (Nzeb), Maria Lopez Zambrano, Paul Kenny, Jamie Goggins
Civil Engineering Research in Ireland 2020
Many of our traditional buildings are disappearing or in danger of being under utilised because they are not comfortable for modern day living and do not meet our present day needs. If a building does not have a use, inevitably it deteriorates and eventually becomes a ruin or gets demolished. It is important to retrofit these buildings, which are part of our identity and can be powerful tourist attractions even though most of them are not listed. Some owners want to apply for retrofitting schemes and grants, but they are rejected because there are no standard solutions to achieve low …
Can Deap Help Us To Predict The Energy Demand And Indoor Temperature Of Homes Before And After Renovation? A Case Study From Dublin,
2020
Civil Engineering, School of Engineering, College of Science & Engineering, National University of Ireland, Galway; SFI MaREI Centre, Ryan Institute, National University of Ireland, Galway, University Road, Galway, Ireland.
Can Deap Help Us To Predict The Energy Demand And Indoor Temperature Of Homes Before And After Renovation? A Case Study From Dublin, Paul Moran, Jamie Goggins
Civil Engineering Research in Ireland 2020
Improving the energy efficiency of buildings via retrofitting is seen as one of the key mitigation measures to reducing the energy demand and carbon emissions of the built environment in Ireland. However, while energy efficiency retrofits for buildings are effective in theory, the energy savings estimated by statistical or engineering models can often be inaccurate. The Domestic Energy Assessment Procedure (DEAP) is the standard assessment procedure used for assessing the energy performance standard of residential buildings in Ireland. This paper examines the gas energy demand for space and water heating and the internal temperature profiles in contrast to DEAP estimates …
Operational And Embodied Energy Analysis Of 8 Single-Occupant Dwellings Retrofit To Nzeb Standard,
2020
Department of Architecture, Planning and Environmental Policy, University College Dublin
Operational And Embodied Energy Analysis Of 8 Single-Occupant Dwellings Retrofit To Nzeb Standard, Richard O'Hegarty, Shane Colclough, Oliver Kinnane, Donal Lennon, Etienne Rieux
Civil Engineering Research in Ireland 2020
In line with the Energy Performance of Buildings Directive, Irish dwellings are being retrofit to near Zero Energy Building (nZEB) standards - with a number of the deep energy retrofits classified as A-rated. As a result of the low operational energy, the embodied energy share of an nZEB's life cycle energy is significantly increased. Therefore, to obtain a holistic picture of the change in energy profile of buildings, the embodied energy of the material added to achieve that low performance should also be taken into account. This paper presents results from a case study of 8 single-occupant terrace bungalows retrofit …
The Broader Development Of The Student Engineer Through Industry Based Experiential Learning,
2020
Department of Civil, Structural and Environmental Engineering, Cork Institute of Technology
The Broader Development Of The Student Engineer Through Industry Based Experiential Learning, Donogh Coleman, Ted Mckenna, Mary Moloney
Civil Engineering Research in Ireland 2020
The global drive for industry-aware and industry-ready engineering graduates, has led to the development and integration of experiential learning through work placements. Industry is looking to recruit graduates with not just the requisite technical engineering skills, but also graduates with inter alia high levels of teamwork and communications skills. This has been recognised by CIT with the integration of work placement in most of its undergraduate programmes. This paper provides an overview of the student placement process in the Department of Civil, Structural and Environmental Engineering at CIT, includes the work placement alternative which was implemented due to the COVID-19 …
Art In Engineering: Evoking A Creative Response From Engineering Students And More,
2020
School of Engineering, National University of Ireland, Galway;Ryan Institute, National University of Ireland, Galway; SFI MaREI Centre for Energy, Climate and Marine, Environmental Research Institute, University College Cork, Cork, Ireland
Art In Engineering: Evoking A Creative Response From Engineering Students And More, Jamie Goggins, Marta Fuente, Eamonn Madden
Civil Engineering Research in Ireland 2020
The concept of creativity being only associated with writers, painters, and artistic professions is outdated. The future engineer must embrace maths, art and creativity to unlock innovative solutions. Traditional engineering courses with an emphasis predominately on maths and science can produce graduates who are constrained in developing design solutions without creativity to unlock innovative solutions. This paper describes a short course introduced in the School of Engineering at NUIGalway in 2018 to expose students to creative thinking research and principles and engage in various forms of creative expression (photography, painting and essay writing) to articulate their response to a set …
Teaching Of Structural Analysis Into The Future,
2020
Department of Civil, Structural and Environmental Engineering, Trinity College Dublin, Ireland
Teaching Of Structural Analysis Into The Future, Dermot O'Dwyer
Civil Engineering Research in Ireland 2020
The engineering curriculum has always been full. In the past civil and structural engineers studied a wide variety of technical subjects within the broad field of engineering science and spent many hours working on design projects. Modern engineering curricula try to cover these areas while also dedicating more time to structured group-work, report writing and communication skills. Although students spend longer in college the number and range of technical fields that students must master is considerably larger than in the past. As a result the time available to any one topic area has reduced. At the same time the work …
Loading On Long Span Bridges In Heavily Trafficked Areas,
2020
School of Engineering, University of Limerick, Limerick, Ireland
Loading On Long Span Bridges In Heavily Trafficked Areas, Michael Quilligan, Eugene O'Brien
Civil Engineering Research in Ireland 2020
The critical traffic loading condition for long-span bridges is congestion when vehicles may be closely spaced together. Data on very high traffic flows is limited however, as induction loops which are typically used to collect traffic data, are ineffective when traffic flow breaks down. A number of long span bridges are located in areas of high traffic with periods of recurring congestion occurring daily. While the inter-vehicle gap distances are greater than those occurring during non-recurring full stop accident type events, the high frequency of the recurring congestion events can increase the probability of a critical load case occurring.
A Numerical Study Of The Effect Of Wind Barriers On Traffic And The Bridge Deck,
2020
School of Civil Engineering, University College Dublin, Ireland
A Numerical Study Of The Effect Of Wind Barriers On Traffic And The Bridge Deck, Yuxiang Zhang, Philip Cardiff, Jennifer Keenahan
Civil Engineering Research in Ireland 2020
Wind actions can have a great impact on both bridges and traffic on bridges. However, structures designed to shelter the traffic from wind can influence the aerodynamic performance of the bridge deck, especially for long-span bridges. This study compares the effect of non-perforated walls and perforated walls used as wind barriers for traffic by conducting Computational Fluid Dynamics (CFD) simulations on three-dimensional geometries of a four-lane bridge deck. Steady-state simulations employ the Reynolds-Averaged Navier Stokes (RANS) method with the k-epsilon turbulence model and all simulations use parallel computing. An open-sourced software OpenFOAM is used.
Long-Run Traffic Simulations For Multi-Lane Road Bridges,
2020
Roughan & O’Donovan Innovative Solutions, Dublin, Ireland
Long-Run Traffic Simulations For Multi-Lane Road Bridges, Róisín Donnelly, Lorcan Connolly, Ilaria Bernardini
Civil Engineering Research in Ireland 2020
The maintenance and repair of ageing bridges is a concern for road infrastructure managers. This issue is amplified by the increasing weights and frequency of travel of freight vehicles in recent times. In order to accurately assess the risk of damage for road bridges, it is essential to have knowledge of both historical and current bridge loading. When available, site-specific Weigh-in-Motion (WIM) data can be effective in creating representative load models for a structure. However, for cases where WIM data is not available and in cases where future damage must be predicted, it is necessary to simulate appropriate data using …
Simulation Of Traffic Loading On Long Span Bridges,
2020
School of Engineering, University of Limerick, Ireland
Simulation Of Traffic Loading On Long Span Bridges, Hang Zhang, Michael Quilligan
Civil Engineering Research in Ireland 2020
Existing long span load models have typically been developed using a number of conservative assumptions, and as such are more applicable to the design of new bridges rather than the assessment of existing structures. Excessive conservatism in such assumptions can lead to expensive and unnecessary interventions in existing bridges. Furthermore, existing load models do not always allow for correlations in traffic weights and vehicle positions on the bridge.
Repair & Rehabilitation Of Daly's (Shakey) Bridge, Cork City,
2020
RPS Group Ltd., Innishmore, Ballincollig, Cork, Ireland
Repair & Rehabilitation Of Daly's (Shakey) Bridge, Cork City, Michael Minehane, John Gamble
Civil Engineering Research in Ireland 2020
This paper describes the rehabilitation of (Shakey) Bridge, an existing single-span suspension bridge crossing the northern channel of the River Lee in Cork City. The bridge was opened in 1927 to replace an earlier ferry crossing at the same location. Daly’s bridge is included on the Record of Protected Structures and the National Inventory of Architectural Heritage. It remains the only suspension bridge in Cork City and is the only surviving bridge of its kind in Ireland. It is considered to be a significant contributor to the architectural heritage of the city. This case study describes the project development including …
