Oil, Gas, and Energy Commons^™

Panel Discussion Presentation: Regional Politics, International Dreams, Kathryn Furlong

North American Energy Water Nexus Roundtable

Panel Discussion: U.S.-Canada Transboundary Perspective

The Main Idea:

What are the drivers of hydro-electric development? What are the influences of domestic politics? In what ways are they international?

Panel Discussion Presentation: Columbia River Treaty, Kelvin Ketchum

North American Energy Water Nexus Roundtable

Panel Discussion: U.S.-Canada Transboundary Perspectives

Slide titles:

- Columbia River Treaty – the setting

- What does the Treaty Do?

- Social & Environmental Costs of the Treaty in Canada

- Treaty benefits and term

- Treaty priorities for water usage

- Example of Flood Control Curves

- Actual Treaty operations

- Supplemental operating agreements

- Treaty Implementation

- Reasons for Treaty Success

Panel Discussion Presentation: Thoughts On Energy/Water Nexus – Energy Technologies, California Case, Terry Surles

North American Energy Water Nexus Roundtable

Panel Discussion: U.S.-Canada Transboundary Perspectives

Energy/Security/Water Problem Confluence:

There remains a critical need to make the best use possible of indigenous
national resources
- Water in the Southwest
- Energy resources in the region and nation

International energy resource competition will require effective development and use of national resources
- Geothermal, solar, wind, coal, uranium

Changing climate can produce "winners" as well as "losers" — requires an
understanding of past climate events and the impact on cultures
- Northern countries may benefit: Canada, Russia
- Temperate countries may suffer due to loss of cropland and increase of
tropical diseases and …

Keynote 1: Energy And Water In The Western And Texas Interconnects, Vincent Tidwell

North American Energy Water Nexus Roundtable

- Estimated Freshwater Withdrawals by Sector: 349 BGD

- U.S. Freshwater Consumption: 100 BGD

- Water for Energy, Energy for Water: Energy and power production requires water; Water production, processing, distribution, and end-use requires energy

Event Program, University Of Nevada, Las Vegas

North American Energy Water Nexus Roundtable

The North American Energy-Water Nexus roundtable was held April 1, 2011, to promote the discussion of how energy and water issues converge in addressing international relations. The roundtable focused on water issues specific to the U.S.-Mexico and U.S.-Canada borders, including stakeholder-driven solutions for water policies and water technologies. The event was co-sponsored by the UNLV Urban Sustainability Initiative; Desert Research Institute; the Canadian Consulate of Los Angeles; and the government of Ontario, Canada.

Developing Criteria For Evaluating The Sustainability Of Emerging Energy, Kurt A. Rosentrater, Elif Kongar

Kurt A. Rosentrater

Over the last decade, the interest in and production of biofuels has grown rapidly. Renewable transportation fuels can be produced from a variety of substrates, using various processing strategies. Feedstock preference and factory scale are geographic dependent. However, it is important to understand the implications of deploying these types of systems on a large scale, both throughout the U.S. as well as globally. To assess the sustainability of various biofuel options, it is crucial to evaluate their performance according to a number of attributes. This has been done using Life Cycle Assessment (LCA). Even so, comparisons among biofuel options are …

Identification Of ‘Carbon Hot-Spots’ And Quantification 1 Of Ghg Intensities In The Biodiesel Supply Chain Using Hybrid Lca And Structural Path Analysis, Adolf Acquaye, Thomas Wiedmann, Kuishang Feng, Robert Crawford, John Barrett, Johan Kuylenstierna, Aidan Duffy, Lenny Koh, Simon Mcqueen-Mason

Articles

It is expected that biodiesel production in the EU will remain the dominant contributor as part of a 10% minimum binding target for biofuel in transportation fuel by 2020 within the 20% renewable energy target in the overall EU energy mix. Life cycle assessments (LCA) of biodiesel to evaluate its environmental impacts have, however, remained questionable, mainly because of the adoption of a traditional process analysis approach resulting in system boundary truncation and because of issues regarding the impacts of land use change and N2O emissions from fertiliser application. In this study, a hybrid LCA methodology is used to evaluate …

Las Negociaciones Entre Las Comunidades Nativas Machiguengas Y La Industria Extractiva Dentro Del Proyecto Camisea: Asesorando Los Roles De Y Las Interacciones Entre Los Actores, Julia Kim

Independent Study Project (ISP) Collection

En esta investigación, estudié cuales eran los roles de actores diferentes en las negociaciones entre las comunidades nativas amazónicas (CC.NN.) y las empresas extractivas dentro del contexto del Proyecto Gas de Camisea (PGC), uno de los proyectos de extracción más importantes en todo America del Sur. Mis objetivos principales eran conocer el rol de cada actor – las CC.NN., las empresas extractivas, el estado, las ONGs, y la misión católica – en las negociaciones y entender como se interactúan y se relacionan. Completé estos objetivos por la siguiente metodología: entrevistas abiertas en Quillabamba, Koribeni, Monte Carmelo, y Kiteni en la …

Biogas Technology On Uzi Island, Zanzibar: A Feasibility Study, Peter J. Mcinerney

Independent Study Project (ISP) Collection

With realization of the finite quantity of fossil fuels and improved study on the effects of global climate change there has been an increasing demand for energy production from renewable, sustainable sources in developed and developing nations alike. The population of Tanzania relies overwhelmingly on biomass as a source of primary energy, with such impacts as deforestation and negative health effects. Biogas generation is a renewable energy technology that utilizes organic waste sources to produce a methane-rich gas suitable for cooking and lighting with the potential to replace current unsustainable energy sources and provide several environmental and socioeconomic benefits. A …

Measuring Progress With Normalized Energy Intensity, Nathan Lammers, J. Kelly Kissock, Brian Abels, Franc Server

Mechanical and Aerospace Engineering Faculty Publications

Energy standard ISO 50001 will require industries to quantify improvement in energy intensity to qualify for certification. This paper describes a four-step method to analyze utility billing, weather, and production data to quantify a company's normalized energy intensity over time. The method uses 3-pararameter change-point regression modeling of utility billing data against weather and production data to derive energy signature equations. The energy signature equation is driven by typical weather and production data to calculate the 'normal annual consumption', NAC, and divided by typical production to calculate 'normalized energy intensity' NEI. These steps are repeated on sequential sets of 12 …

Improving Compressed Air Energy Efficiency In Automotive Plants: Practical Examples And Implementation, Nasr Alkadi, J. Kelly Kissock

Mechanical and Aerospace Engineering Faculty Publications

The automotive industry is the largest industry in the United States in terms of the dollar value of production [1]. U.S. automakers face tremendous pressure from foreign competitors, which have an increasing manufacturing presence in this country. The Big Three North American Original Equipment Manufacturers (OEMs)-General Motors, Ford, and Chrysler-are reacting to declining sales figures and economic strain by working more efficiently and seeking out opportunities to reduce production costs without negatively affecting the production volume or the quality of the product. Successful, cost-effective investment and implementation of the energy efficiency technologies and practices meet the challenge of maintaining the …

Embodied Emissions Abatement: A Policy Assessment Using Stochastic Analysis, Adolf Acquaye, Aidan Duffy, Biswajit Basu

Articles

Policymakers traditionally focus on regulating operational energy use in buildings, ignoring other life cycle components such as embodied energy even though this may account for a significant portion of life cycle emissions. Data relating to embodied energy and emissions in buildings is limited. However, stochastic techniques can be used to estimate the distribution of such emissions from buildings. This helps policymakers identify which instruments are appropriate for achieving emissions reductions. A primary aim of this paper is to demonstrate this approach using a sample of apartment buildings in Ireland. A Monte-Carlo simulation suggests that the average probability distribution of embodied …

Approaches To Alternative Energy Policy: A Comparison Of The United States And Germany, Martina Dzuna

Environment and Sustainability Honors Papers

This paper will examine the types of alternative energies that are available at this point, focus on the formation of markets for alternative energy and discuss how new energy technology enters and then diffuses into the markets. Along with energy technology diffusion, this paper will examine how policy structures make technology diffusion possible and which types of policy are most effective. To answer this question, the report uses Germany and the United States as case studies. From the case studies, we will be able to draw some conclusions about what makes some policies more successful than others, and make recommendations …

Wind For Schools: Fostering The Human Talent Supply Chain For A 20% Wind Energy Future, Ian Baring-Gould

Publications (E)

As the United States dramatically expands wind energy deployment, the industry is challenged with developing a skilled workforce and addressing public resistance. Wind Powering America’s Wind for Schools project addresses these issues by:
• Developing Wind Application Centers (WACs) at universities; WAC students assist in implementing school wind turbines and participate in wind courses
• Installing small wind turbines at community “host” schools
• Implementing teacher training with interactive curricula at each host school.

Correlations Of Capacitance-Voltage Hysteresis With Thin-Film Cdte Solar Cell Performance During Accelerated Lifetime Testing, David S. Albin, Joseph A. Del Cueto

Publications (E)

In this paper we present the correlation of CdTe solar cell performance with capacitance-voltage hysteresis, defined presently as the difference in capacitance measured at zero-volt bias when collecting such data with different pre-measurement bias conditions. These correlations were obtained on CdTe cells stressed under conditions of 1-sun illumination, open-circuit bias, and an acceleration temperature of approximately 100 ºC.

Effect Of Hysteresis On Measurements Of Thin-Film Cell Performance, David S. Albin, Joseph A. Del Cueto

Publications (E)

Transient or hysteresis effects in polycrystalline thin film CdS/CdTe cells are a function of pre-measurement voltage bias and whether Cu is introduced as an intentional dopant during back contact fabrication. When Cu is added, the current-density (J) vs. voltage (V) measurements performed in a reverse-to-forward voltage direction will yield higher open-circuit voltage (V_oc), up to 10 mV, and smaller short-circuit current density (J_sc), by up to 2 mA/cm², relative to scanning voltage in a forward-to-reverse direction. The variation at the maximum power point, Pmax, is however small. The resulting variation in FF can be …

Use Of 2nd And 3rd Level Correlation Analysis For Studying Degradation In Polycrystalline Thin-Film Solar Cells, David S. Albin, Joseph A. Del Cueto, S. H. Demtsu, S. Bansal

Publications (E)

The correlation of stress-induced changes in the performance of laboratory-made CdTe solar cells with various 2^nd and 3^rd level metrics is discussed. The overall behavior of aggregated data showing how cell efficiency changes as a function of open-circuit voltage (V_oc), shortcircuit current density (J_sc), and fill factor (FF) is explained using a two-diode, PSpice model in which degradation is simulated by systematically changing model parameters. FF shows the highest correlation with performance during stress, and is subsequently shown to be most affected by shunt resistance, recombination and in some cases voltage-dependent collection. Large decreases …

High Efficiency, Low Cost Solar Cells Manufactured Using ‘Silicon Ink’ On Thin Crystalline Silicon Wafers October 2009 - November 2010, Homer Antoniadis

Publications (E)

The objectives of Phase I (Feb – Oct 2009) include the development and demonstration of a 17% efficient 25mm x 25mm crystalline Silicon solar cell and a 16% efficient 125mm x 125mm crystalline Silicon solar cell, both produced by Ink-jet printing Silicon Ink on a thin crystalline Sil-icon wafer. To achieve these objectives, processing approaches were developed to print the Silicon Ink in a predetermined pattern to form a high efficiency selective emitter, remove the solvents in the Silicon Ink and fuse the deposited particle Silicon films. Additionally, standard solar cell manufacturing equipment with slightly modified processes were used to …

Hybrid Cooling Systems For Low-Temperature Geothermal Power Production, Andrea Ashwood, Desikan Bharathan

Publications (E)

The overall objective of this investigation is to identify and evaluate methods by which the net power output of an air-cooled geothermal power plant can be enhanced during hot ambient conditions using minimal amounts of water.

Geothermal power plants that use air-cooled heat rejection systems experience a decrease in power production during hot periods of the day. This decrease in power output typically coincides with the time when utilities need power to address high air conditioning loads. Hybrid cooling options, which use both air and water, have been studied for this report to assess how they might mitigate the net …

The Silver Spark For Nevada, Walt Borland, James A. Croce, Richard Seline

Publications (E)

The SILVER Spark for Nevada: Sustainable Innovation Leading a Vital Economic Renaissance

Nevada. A State of stark contrasts, with historic booms and devastating busts experienced throughout its modern history. A State frequently forced to reinvent itself as ever-evolving circumstances have demanded. A State that has been driven to the edge time after time and, yet again and again, has managed to discover another way to prosper. A State that now finds itself in a precarious position as the “Great Recession” hit it harder than any other and has left it struggling to recover.

As you will conclude by reading The …

Tracking The Deepwater Horizon Oil Spill: A Modeling Perspective, Yonggang Liu, Robert H. Weisberg, Chuanmin Hu, Lianyuan Zheng

Yonggang Liu

The Deepwater Horizon oil spill was caused by a drilling rig explosion on 20 April 2010 that killed 11 people. It was the largest oil spill in U.S. history and presented an unprecedented threat to Gulf of Mexico marine resources. Although oil gushing to the surface diminished after the well was capped, on 15 July 2010, much remains to be known about the oil and the dispersants beneath the surface, including their trajectories and effects on marine life. A system for tracking the oil, both at the surface and at depth, was needed for mitigation efforts and ship survey guidance. …

Creep In Photovoltaic Modules: Examining The Stability Of Polymeric Materials And Components, David C. Miller, Michael D. Kempe, Stephen H. Glick, Sarah R. Kurtz

Publications (E)

Interest in renewable energy has motivated the implementation of new polymeric materials in photovoltaic modules. Some of these are non-cross-linked thermoplastics, in which there is a potential for new behaviors to occur, including phase transformation and visco-elastic flow. Differential scanning calorimetry and rheometry data were obtained and then combined with existing site-specific time-temperature information in a theoretical analysis to estimate the displacement expected to occur during module service life. The analysis identified that, depending on the installation location, module configuration and/or mounting configuration, some of the thermoplastics are expected to undergo unacceptable physical displacement. While the examples here focus on …

Accelerated Stress Testing Of Hydrocarbon-Based Encapsulants For Medium-Concentration Cpv Applications, M. D. Kempe, T. J. Moricone, M. Kilkenny, J. Z. Zhang

Publications (E)

Concentrating photovoltaic (CPV) systems have great potential to reduce photovoltaic (PV) electricity costs because of the relatively low cost of optical components as compared to PV cells. A transparent polymeric material is used to optically couple the PV cell to optical components and is thus exposed to the concentrated light source at elevated temperatures. In this work polymeric encapsulant materials are positioned close to a Xenon arc lamp to expose them to ultraviolet radiation (UV) that is about 42 times as intense as sunlight. Furthermore, different glass types are used as filters to modify the spectral distribution of light in …

Impacts Of Mid-Level Biofuel Content In Gasoline On Sidi Engine-Out And Tailpipe Particulate Matter Emissions, Xin He, John C. Ireland, Bradley T. Zigler, Matthew A. Ratcliff, Keith E. Knoll, Teresa L. Alleman, John T. Tester

Publications (E)

In this work, the influences of ethanol and iso-butanol blended with gasoline on engine-out and post three-way catalyst (TWC) particle size distribution and number concentration were studied using a General Motors (GM) 2.0L turbocharged spark ignition direct injection (SIDI) engine. The engine was operated using the production engine control unit (ECU) with a dynamometer controlling the engine speed and the accelerator pedal position controlling the engine load. A TSI Fast Mobility Particle Sizer (FMPS) spectrometer was used to measure the particle size distribution in the range from 5.6 to 560 nm with a sampling rate of 1 Hz. U.S. federal …

Considerations For How To Rate Cpv, Sarah R. Kurtz, Matthew Muller, Bill Marion, Keith Emery, Robert Mcconnell, Sandheep Surendran, Adrianne Kimber

Publications (E)

The concentrator photovoltaic (CPV) industry is introducing multiple products into the marketplace, but, as yet, the community has not embraced a unified method for assessing a nameplate rating. The choices of whether to use 850, 900, or 1000 W/m² for the direct-normal irradiance and whether to link the rating to ambient or cell temperature will affect how CPV modules are rated and compared with other technologies. This paper explores the qualitative and quantitative ramifications of these choices using data from two multi-junction CPV modules and two flat-plate modules.

"Buried-Anode" Technology Leads To Advanced Lithium Batteries, National Renewable Energy Laboratory

Publications (E)

A technology developed at the National Renewable Energy Laboratory has sparked a start-up company that has attracted funding from the Advanced Projects Research Agency-Energy (ARPA-E). Planar Energy, Inc. has licensed NREL's "buried-anode" technology and put it to work in solid-state lithium batteries. The company claims its large-format batteries can achieve triple the performance of today's lithium-ion batteries at half the cost, and if so, they could provide a significant boost to the emerging market for electric and plug-in hybrid vehicles.

Outdoor Pv Degradation Comparison, Dirk C. Jordan, R. M. Smith, C. R. Osterwald, E. Gelak, Sarah R. Kurtz

Publications (E)

As photovoltaic (PV) penetration of the power grid increases, it becomes vital to know how decreased power output may affect cost over time. In order to predict power delivery, the decline or degradation rates must be determined accurately. At the Performance and Energy Rating Testbed (PERT) at the Outdoor Test Facility (OTF) at the National Renewable Energy Laboratory (NREL) more than 40 modules from more than 10 different manufacturers were compared for their long-term outdoor stability. Because it can accommodate a large variety of modules in a limited footprint the PERT system is ideally suited to compare modules side-by-side under …

Measuring Degradation Rates Without Irradiance Data, Steve Pulver, Daniel Cormode, Alex Cronin, Dirk C. Jordan, Ryan Smith, Sarah R. Kurtz

Publications (E)

A method to report PV system degradation rates without using irradiance data is demonstrated. First, a set of relative degradation rates are determined by comparing daily AC final yields from a group of PV systems relative to the average final yield of all the PV systems. Then, the difference between relative and absolute degradation rates is found from a statistical analysis. This approach is verified by comparing to methods that utilize irradiance data. This approach is significant because PV systems are often deployed without irradiance sensors, so the analysis method described here may enable measurements of degradation using data that …

Quantifying The Thermal Fatigue Of Cpv Modules, Nick Bosco, Sarah R. Kurtz

Publications (E)

A method is presented to quantify thermal fatigue in the CPV die-attach from meteorological data. A comparative study between cities demonstrates a significant difference in the accumulated damage. These differences are most sensitive to the number of larger (ΔT) thermal cycles experienced for a location. High frequency data (<1/min) may be required to most accurately employ this method.

The Impact Of Driving Conditions On Phev Battery Performance, Nathan Christensen, John Patten, Steven Srivastava, Gary P. Nola

Green Manufacturing Research Journal

The battery performance of a modified Prius with a 5 kWh plug-in battery was documented for a year to determine the impact of environmental conditions and user attributes on vehicle performance. Both fuel economy and pure electrical efficiency were compared to ambient temperature. The fuel economy has a positive relationship with ambient temperature until approximately 70˚F where the efficiency begins to drop. Electrical performance has a positive linear relationship with ambient temperature. With the emergence of electric vehicles (EVs) and PHEVs from a variety of automotive manufacturers, information on EV and PHEV performance for consumers will become more important.