Mechanical Engineering Commons^™

A Platinum Nanowire Network As A Highly Effective Current Collector For Intermediate Temperature Solid Oxide Fuel Cells, Hanping Ding, Xingjian Xue

Faculty Publications

We report the fabrication and evaluation of a platinum nanowire network as a highly efficient current collector for solid oxide fuel cells (SOFCs). The ink of carbon-black supported platinum nanoparticles was sprayed onto the cathode. After firing, the carbon black was oxidized and disappeared as carbon dioxide gas while the platinum nanoparticles connect with one another, forming a tree-branch-like nanowire network. The diameters of the nanowires range from 100 nm to 400 nm. Compared to a conventional platinum paste current collector, the polarization resistance of the PrBaCo₂O_5+δ (PBCO) cathode with a nanowire current collector was reduced …

Modeling Of Chemical-Mechanical Couplings In Solid Oxide Cells And Reliability Analysis, Xinfang Jin

Theses and Dissertations

Solid oxide fuel cell (SOFC) has been well demonstrated as a promising clean energy conversion technology. For practical applications, the SOFC systems should have both good electrochemical performance and high reliability. The SOFCs are usually operated under very aggressive conditions, e.g., high temperatures (600-1000oC) and extremely low oxygen partial pressures (anode electrode). These aggressive operating conditions could lead to a variety of material system degradations, imposing great challenges on meeting lifetime requirement of SOFC commercial applications. It is therefore essential to increase the understanding of fundamental SOFC degradation mechanisms.

The basic structure of SOFCs is a positive electrode-electrolyte-negative electrode (PEN) …

Material Synthesis And Fabrication Method Development For Intermediate Temperature Solid Oxide Fuel Cells, Hanping Ding

Theses and Dissertations

Solid oxide fuel cells (SOFCs) are operated in high temperature conditions (750-1000 oC). The high operating temperature in turn may lead to very complicated material degradation issues, significantly increasing the cost and reducing the durability of SOFC material systems. In order to widen material selections, reduce cost, and increase durability of SOFCs, there is a growing interest to develop intermediate temperature SOFCs (500-750 oC). However, lowering operating temperature will cause substantial increases of ohmic resistance of electrolyte and polarization resistance of electrodes. This dissertation aimed at developing high-performance intermediate-temperature SOFCs through the employment of a series of layered perovskite oxides …

Classification Of Low Velocity Impactors Using Spiral Sensing Of Acousto-Ultrasonic Waves, Chijioke Agbasi

Theses and Dissertations

The non-linear elastodynamics of a flat plate subjected to low velocity foreign body impacts is studied, resembling the space debris impacts on the space structure. The work is based on a central hypothesis that in addition to identifying the impact locations, the material properties of the foreign objects can also be classified using acousto-ultrasonic signals (AUS). Simultaneous localization of impact point and classification of impact object is quite challenging using existing state-of-the-art structural health monitoring (SHM) approaches. Available techniques seek to report the exact location of impact on the structure, however, the reported information is likely to have errors from …

Measuring The Effectiveness Of Education For Sustainable Development Interventions For Effecting Change In Knowledge, Attitude And Behaviors Toward Sustainable Development, Christopher Robin Wilson

Theses and Dissertations

The question addressed by this study is whether an intervention involving a brief, focused seminar providing Sustainability Fundamental education can affect change in sustainability-centric behavior via measured change in attitude toward sustainability and/or change knowledge of sustainability fundamentals.

This study focused on applying and extending lessons from a previous exploration of the relationships between sustainable behavior and both attitude toward sustainability and knowledge of sustainability. The test involved determining whether brief, science-based sustainability fundamentals seminars are an effective intervention for affecting the favorable sustainable behavior of practicing engineers, defined as professionals engaged in engineering post-completion of their formal studies, in …

Ni-Doped Sr2Fe1.5Mo0.5O6-Δ As Anode Materials For Solid Oxide Fuel Cells, Guoliang Xiao, Siwei Wang, Ye Lin, Zhibin Yang, Minfang Han, Fanglin Chen

Faculty Publications

10% Ni-doped Sr₂Fe_1.5Mo_0.5O_6-δ with A-site deficiency is prepared to induce in situ precipitation of B-site metals under anode conditions in solid oxide fuel cells. XRD, SEM and TEM results show that a significant amount of nano-sized Ni-Fe alloy metal phase has precipitated out from Sr_1.9Fe_1.4Ni_0.1Mo_0.5O_6-δ upon reduction at 800^◦C in H₂. The conductivity of the reduced composite reaches 29 S cm⁻¹ at 800^◦C in H₂. Furthermore, fuel cell performance of the composite anode Sr_{1.9 …}

Influence Of Crystal Structure On The Electrochemical Performance Of A-Site-Deficient Sr1-SNb0.1Co0.9O3-Δ Perovskite Cathodes, Yinlong Zhu, Ye Lin, Xuan Shen, Jaka Sunarso, Wei Zhou, Shanshan Jiang, Dong Su, Fanglin Chen, Zongping Shao

Faculty Publications

The creation of A-site cation defects within a perovskite oxide can substantially alter the structure and properties of its stoichiometric analogue. In this work, we demonstrate that by vacating 2 and 5% of Asite cations from SrNb_0.1Co_0.9O_3-δ (SNC1.00) perovskites (Sr_1-sNb_0.1Co_0.9O_3-δ,s = 0.02 and 0.05; denoted as SNC0.98 and SNC0.95, respectively), a Jahn–Teller (JT) distortion with varying extents takes place, leading to the formation of a modified crystal lattice within a the perovskite framework. Electrical conductivity, electrochemical performance, chemical compatibility and microstructure of Sr_1-sNb_0.1Co …

Modeling Of Chemical-Mechanical Couplings In Anode-Supported Solid Oxide Fuel Cells And Reliability Analysis, Xinfang Jin, Xingjian Xue

Faculty Publications

Oxygen ionic transport in conducting ceramics is an important mechanism enabling solid oxide fuel cell (SOFC) technology. The multi-physicochemical processes lead to the fact that the distribution of oxygen vacancy site fraction is not uniform in a positive-electrode electrolyte negative-electrode (PEN) assembly. Different oxygen vacancy concentrations induce different volumetric expansion of ceramics, resulting in complicated chemical–mechanical coupling phenomena and chemical stress in SOFCs. In this research, a mathematical model is developed to study oxygen ionic transport induced chemical stress in an SOFC. The model is validated using experimental polarization curves. Comprehensive simulations are performed to investigate chemical stress distribution in …

Design, Fabrication, And Properties Of 2-2 Connectivity Cement/Polymer Based Piezoelectric Composites With Varied Piezoelectric Phase Distribution, Xu Dongyu, Cheng Xin, Sourav Banerjee, Huang Shifeng

Faculty Publications

The laminated 2-2 connectivity cement/polymer based piezoelectric composites with variedpiezoelectric phase distribution were fabricated by employing Lead Zirconium Titanate ceramicas active phase, and mixture of cement powder, epoxy resin, and hardener as matrix phase with a mass proportion of 4:4:1. The dielectric, piezoelectric, and electromechanical coupling properties of the composites were studied. The composites with large total volume fraction ofpiezoelectric phase have large piezoelectric strain constant and relative permittivity, and thepiezoelectric and dielectric properties of the composites are independent of the dimensional variations of the piezoelectric ceramic layer. The composites with small total volume fraction of piezoelectric phase have large …

Low Frequency Energy Scavenging Using Sub-Wave Length Scale Acousto-Elastic Metamaterial, Raiz U. Ahmed, Sourav Banerjee

Faculty Publications

This letter presents the possibility of energy scavenging (ES) utilizing the physics of acousto-elastic metamaterial (AEMM) at low frequencies (<∼3KHz). It is proposed to use the AEMM in a dual mode (Acoustic Filter and Energy Harvester), simultaneously. AEMM’s are typically reported for filtering acoustic waves by trapping or guiding the acoustic energy, whereas this letter shows that the dynamic energy trapped inside the soft constituent (matrix) ofmetamaterials can be significantly harvested by strategically embedding piezoelectric wafers in the matrix. With unit cell AEMM model, we experimentally asserted that at lower acoustic frequencies (< ∼3 KHz), maximum power in the micro Watts (∼35µW) range can be generated, whereas, recently reported phononic crystal based metamaterials harvested only nano Watt (∼30nW) power against 10KΩ resistive load. Efficient energy scavengers at low acoustic frequencies are almost absent due to large required size relevant to the acoustic wavelength. Here we report sub wave length scale energy scavengers utilizing the coupled physics of local, structural and matrix resonances. Upon validation of the argument through analytical, numerical and experimental studies, a multi-frequency energy scavenger (ES) with multi-cellmodel is designed with varying geometrical properties capable of scavenging energy (power output from ∼10µW – ∼90µW) between 0.2 KHz and 1.5 KHz acoustic frequencies.

There Can Be Turbulence In Microfluidics At Low Reynolds Number, Guiren Wang, F. Yang, Wei Zhao

Faculty Publications

Turbulence is commonly viewed as a type of macroflow, where the Reynolds number (Re) has to be sufficiently high. In microfluidics, when Re is below or on the order of 1 and fast mixing is required, so far only chaotic flow has been reported to enhance mixing based on previous publications since turbulence is believed not to be possible to generate in such a low Re microflow. There is even a lack of velocimeter that can measure turbulence in microchannels. In this work, we report a direct observation of the existence of turbulence in microfluidics with Re on the order …

Heat Transfer Enhancement By Three-Dimensional Surface Roughness Technique In Nuclear Fuel Rod Bundles, Kang Liu

Theses and Dissertations

DISS_abstract> This thesis investigate thermal characteristic of a single-phase nano-fluid in a single heater element loop tester and provides a comparison between heat transfer enhancement results achieved using water as a coolant and using nano-fluids with different volume percentage. The experimental investigation is performed on two simulated nuclear fuel rods with two different types of modified outer surfaces roughness. The fuel rod surfaces modified are termed as two-dimensional surface roughness (square transverse ribbed surface) and three-dimensional surface roughness (Diamond shaped blocks). The nano-fluid used are 0.5% and 2% ZnO-Deionized water based nano-fluid. The maximum heat transfer co-efficient enhancement achieved compared …