Mechanical Engineering Commons^™

Combined Risk Based Inspection And Fault Tree Analysis For Repetitive 3-Phase Line Piping Leakage At West Java Offshore Topside Facility, Dona Yuliati, Akhmad Herman Yuwono, Datu Rizal Asral, Donanta Dhaneswara

Journal of Materials Exploration and Findings (JMEF)

Hydrocarbon releases might result in serious consequences in various aspects. In addition to the contribution to environmental pollution, repetitive leakages need high repair costs. This study aim is to minimize potential repetitive leakage for other typical 3-phase piping systems. We conducted the risk assessment by adopting Risk Based Inspection (RBI) API 581 to identify risk level, calculating piping lifetime, recommended inspection plan and mitigations. The most relevant root causes can be obtained through quantitative Fault Tree Analysis (FTA). Observation and investigation was taken from eight 3-phase piping systems that experienced repetitive leakages. It has been found that the risk level …

Nitrogen Gas Quenching Pressure Effect On Bs S155 Alloy Steel In Vacuum Furnace, Agus Mulyadi Hasanudin, Eddy Sumarno Siradj

Journal of Materials Exploration and Findings (JMEF)

The production of metal and alloy products requires the use of heat treatment, when during the heat treatment process, quenching is a crucial step. The quenching medium can be anything from water, a salt bath, oil, air and gas. In a vacuum furnace, pressurized gas, most frequently nitrogen (N₂) gas, serves as one of the quenching mediums. One of the drawbacks of the quenching process is the distortion and dimensional change of the parts. This paper aims to investigate the influence of nitrogen gas quenching pressure on the distortion and dimensional change of aerospace actuator gear planet parts …

Advances In Cellulose Nanomaterial-Based Foams For Environmental Applications, Md Musfiqur Rahman

Electronic Theses and Dissertations

The use of metal-oxide nanoparticles adsorbents is limited to fixed-bed columns in industrial-scale water treatment applications. This limitation is commonly attributed to the tendency of nanoparticles to aggregate, the use of non-sustainable and inefficient polymeric resins as supporting materials, or a lack of adsorption capacity. Foams and aerogels derived from cellulose nanomaterials have unique characteristics, such as high porosity and low density, which enables their use in a variety of environmental applications, including water treatment. However, the overall use of cellulose nanomaterial-based foams in various environmental sectors is limited due to the high cost of production associated with time- and …

Characterization Of Interlayer Laser Shock Peening During Fused Filament Fabrication Of Polylactic Acid (Pla), Fabien Denise

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

The field of additive manufacturing (AM) has gained a significant amount of popularity due to the increasing need for more sustainable manufacturing techniques and the adaptive development of complex product geometries. The problem is that AM parts routinely exhibit flaws or weaknesses that affect functionality or performance. Over the years, surface treatments have been developed to compensate certain flaws or weaknesses in manufactured products. Combining surface treatments with the modularity of additive manufacturing could lead to more adaptable and creative improvements of product functions in the future. The current work evaluates the feasibility of pursuing a new research axis in …

Characterization Of Mechanically Recycled Polylactic Acid (Pla) Filament For 3d-Printing By Evaluating Mechanical, Thermal, And Chemical Properties And Process Performance, Mahsa Shabani Samghabady

All Theses

Polylactic acid (PLA) is a biopolymer made from renewable resources such as sugar and corn. PLA filament is a popular material used in Fused Deposition Modeling (FDM) 3D-printing. While this material has many advantages, all the failed parts, support structures, rafts, nozzle tests, and the many prototype iterations during the 3D-printing process contribute to the plastic pollution and release of greenhouse gases. Although PLA is biodegradable, it can take years to degrade in landfills. Instead of throwing away PLA waste and buying new filaments, PLA can be recycled. Amongst the different recycling technologies, mechanical recycling is the most environmentally friendly. …

The Effect Of Heat Treatment And Chemical Treatment On Natural Fibre To The Durability Of Wood Plastic Composites – A Review, Nuratiqah Asyiqin Mohd Nasharudin, Nur Fatihah Sulaiman, Nurul Aziemah Mohammad, Wan Nor Raihan Wan Jaafar, Falah Abu Dr., Siti Norasmah Surip

Journal of Materials Exploration and Findings (JMEF)

The application of WPC is not only limited to indoor applications but has been extended to exterior applications where properties of WPC could compromise during service life. WPC was derived from wood fiber of various sizes to reinforce polymers. Wood fiber has the advantage of a cheaper price, being abundantly available, and ease of processing, however, the critical factor is its hydrophilic nature, where moisture absorption is likely to occur. Thus, treatments for reducing the hydrophilicity of wood fibers are applied. By treatment of wood fiber, the surface impurities were removed, leaving the roughened surface of fibers, thus providing a …

Du Undergraduate Showcase: Research, Scholarship, And Creative Works, Caitlyn Aldersea, Justin Bravo, Sam Allen, Anna Block, Connor Block, Emma Buechler, Maria De Los Angeles Bustillos, Arianna Carlson, William Christensen, Olivia Kachulis, Noah Craver, Kate Dillon, Muskan Fatima, Angel Fernandes, Emma Finch, Colleen Cassidy, Amy Fishman, Andrea Francis, Stacia Fritz, Simran Gill, Emma Gries, Rylie Hansen, Shannon Powers, Jacqueline Martinez, Zachary Harker, Ashley Hasty, Mykaela Tanino-Springsteen, Kathleen Hopps, Adelaide Kerenick, Colin Kleckner, Ci Koehring, Elijah Kruger, Braden Krumholz, Maddie Leake, Lyneé Alves, Seraphina Loukas, Yatzari Lozano Vazquez, Haley Maki, Emily Martinez, Sierra Mckinney, Mykaela Tanino-Springsteen, Audrey Mitchell, Kipling Newman, Audrey Ng, Megan Lucyshyn, Andrew Nguyen, Stevie Ostman, Casandra Pearson, Alexandra Penney, Julia Gielczynski, Tyler Ball, Anna Rini, Christina Rorres, Simon Ruland, Helayna Schafer, Emma Sellers, Sarah Schuller, Claire Shaver, Kevin Summers, Isabella Shaw, Madison Sinar, Claudia Pena, Apshara Siwakoti, Carter Sorensen, Madi Sousa, Anna Sparling, Alexandra Revier, Brandon Thierry, Dylan Tyree, Maggie Williams, Lauren Wols

DU Undergraduate Research Journal Archive

DU Undergraduate Showcase: Research, Scholarship, and Creative Works

Controlling Mechanical Properties Of Well-Defined Polymer Networks, Ipek Sacligil

Doctoral Dissertations

Polymer networks are one of the most versatile and highly studied material class that revolutionized many aspects of life. Connecting the final network properties to the molecular parameters of its building blocks remains a major research thrust. Recent advances in network synthesis techniques allowed for accurate predictions of elastic modulus in model networks. Tew Group has developed highly efficient, thiol-norbornene networks with controllable mechanical properties. Chapter 2 focuses on modifying the gel fracture energy predicted by Lake-Thomas theory by accounting for loop defects. This study allowed for a priori estimates of gel fracture energy by combining theory, experiments, and simulations. …

Sharprazor: Automatic Removal Of Hair And Ruler Marks From Dermoscopy Images, Reda Kasmi, Jason Hagerty, Reagan Harris Young, Norsang Lama, Januka Nepal, Jessica Miinch, William V. Stoecker, R. Joe Stanley

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Background: The removal of hair and ruler marks is critical in handcrafted image analysis of dermoscopic skin lesions. No other dermoscopic artifacts cause more problems in segmentation and structure detection. Purpose: The aim of the work is to detect both white and black hair, artifacts and finally inpaint correctly the image. Method: We introduce a new algorithm: SharpRazor, to detect hair and ruler marks and remove them from the image. Our multiple-filter approach detects hairs of varying widths within varying backgrounds, while avoiding detection of vessels and bubbles. The proposed algorithm utilizes grayscale plane modification, hair enhancement, segmentation using tri-directional …

Enabling An Equitable Energy Transition Through Inclusive Research, Michael Ash, Erin Baker, Mark Tuominen, Dhandapani Venkataraman, Matthew Burke, S. Castellanos, M. Cha, Gabe Chan, D. Djokic, J.C. Ford, Anna P. Goldstein, David Hsu, Matt Lacker, C. Miller, D. Nock, A.P. Ravikumar, Allison Bates, Anna Stefanopoulou, E Grubert, D.M Kammen, M. Pastor, S.Z, Attari, S. Carley, D.L Clark, D. Dean-Ryan, U. Kosar, Kerry Bowie, Tina Johnson

ETI Publications

Comprehensive and meaningful inclusion of marginalized communities within the research enterprise will be critical to ensuring an equitable, technology-informed, clean energy transition. We provide five key action items for government agencies and philanthropic institutions to operationalize the commitment to an equitable energy transition.

Molecular Dynamics Modeling Of Polymers For Aerospace Composites, Swapnil Sambhaji Bamane

Dissertations, Master's Theses and Master's Reports

Polymer matrix composite materials are widely used as structural materials in aerospace and aeronautical vehicles. Resin/reinforcement wetting and the effect of polymerization on the thermo-mechanical properties of the resin are key parameters in the manufacturing of aerospace composite materials. Determining the contact angle between combinations of liquid resin and reinforcement surfaces is a common method for quantifying wettability. It is challenging to determine contact angle values experimentally of high-performance resins on CNT materials such as CNT, graphene, bundles or yarns, and BNNT surfaces. It is also experimentally difficult to determine the effect of polymerization reaction on material properties of a …

Thermotrophy Exploratory Study, James Weifu Lee

Chemistry & Biochemistry Faculty Publications

The question of whether environmental heat energy could be utilized as a source of energy for biological metabolism is the center of this exploratory research. In 1979, this author postulated a hypothesis for the existence of thermotrophs that could isothermally utilize environmental heat energy as a source of their energy on Earth. According to this hypothesis, the thermotrophs could be the first primitive forms of life in the early Earth environment. The chemotrophs and phototrophs that we currently are all well familiar with might have been evolved somehow from the primitive thermotrophs. Furthermore, all the organisms currently regarded as the …

Coconut Shell Waste Treatment Technology For A Sustainable Waste Utilization: A Case Study Of The Smes In Bohol Village, Indonesia, Wahyu Anggo Rizal, Ria Suryani, Roni Maryana, Dwi Joko Prasetyo, Diah Pratiwi, Yuli Ary Ratnawati, Dini Ariani, Andri Suwanto

ASEAN Journal of Community Engagement

This project focused on the introduction of liquid smoke and bio briquette manufacturing technology to small and medium enterprises (SMEs) located in Bohol Village, Gunungkidul, Indonesia through technology transfer, training, and mentoring. These SMEs are engaged in the food business with the main product jenang ketan, a traditional food from Gunungkidul, especially in Rongkop District, and very popular among communities around and outside Gunungkidul. The traditional preparation of jenang ketan produces several by-products in the form of waste, which is dominated by coconut shell biomass. The project’s technology transfer was carried out through the procurement of a series of pyrolysis …

Direct Ink Write And Thermomechanical Characterization Of Thermoset Composites, Sergio Dante Favela

Open Access Theses & Dissertations

This research will be divided into two sections. The first section discusses direct ink writing and thermomechanical characterization for thermoset composites. The thermoset ink is prepared with fillers aiding the printing process by modifying the rheology of the ink and geometry retention by allowing for the part to have an initial UV cure step. Three specimen formulations with different weight percentages were printed by material extrusion in the shape of tensile specimens following ASTM standard D638 to characterize the mechanical properties at room temperature, 100â?? and 200â??. Furthermore, the ink resin was characterized through DSC, TGA, and rheology testing. The …

Processing Of Plastic Film From Potato Starch: Effect Of Drying Methods, Kourtney Collier, Samantha Goins, Austin Chirgwin, Isabelle Stanfield

The Journal of Purdue Undergraduate Research

Starch-based plastics are biodegradable, compostable compounds made of starch and plasticizers from natural sources. Their fabrication involves the starch-plasticizer reaction at 70–100°C followed by cooling and drying. Th e most common drying method is air drying (natural convection), which is effective but slow. Th e objective of this work is to study the effect of fast drying (forced convection) on the quality of the plastic film. Th is work compares the effects of drying conditions and drying rate on warpage, shrinkage rate, and presence of bubbles. Five drying methods are studied: (1) natural convection with uncovered petri dish, (2) natural …

Aircraft Engine Particulate Matter Emissions From Sustainable Aviation Fuels: Results From Ground-Based Measurements During The Nasa/Dlr Campaign Eclif2/Nd-Max, Tobias Schripp, Bruce E. Anderson, Uwe Bauder, Bastian Rauch, Joel C. Corbin, Greg J. Smallwood, Prem Lobo, Ewan C. Crosbie, Michael A. Shook, Richard C. Miake-Lye, Zhenhong Yu, Andrew Freedman, Philip D. Whitefield, Claire E. Robinson

Chemistry Faculty Research & Creative Works

The use of alternative jet fuels by commercial aviation has increased substantially in recent years. Beside the reduction of carbon dioxide emission, the use of sustainable aviation fuels (SAF) may have a positive impact on the reduction of particulate emissions. This study summarizes the results from a ground-based measurement activity conducted in January 2018 as part of the ECLIF2/ND-MAX campaign in Ramstein, Germany. Two fossil reference kerosenes and three different blends with the renewable fuel component HEFA-SPK (Hydroprocessed Esters and Fatty Acids Synthetic Paraffinic Kerosene) were burned in an A320 with V2527-A5 engines to investigate the effect of fuel naphthalene/aromatic …

Enhancement Of Energy Efficiency For Thermal Energy And Biomass Driven Applications, Osama Mansour Selim Elsayed

Theses and Dissertations

The importance of gas turbine blades is to convert the thermal energy into shaft work output, which makes the turbine blades are one of the critical components of the gas turbines. Besides the mechanical stresses caused by the centrifugal force and the fluid forces, the thermal stresses arise because of the temperature gradient within the blade materials. This paper aims to have a uniform circumferential temperature field at the combustor exit, consequently reducing the thermal stresses caused by the non-uniform temperature distribution along the turbine blade. The validation of the simulation results with the experiments showed an acceptable agreement with …

Bbt Acoustic Alternative Top Bracing Cadd Data Set-Norev-2022jun28, Bill Hemphill

STEM Guitar Project’s BBT Acoustic Kit

This electronic document file set consists of an overview presentation (PDF-formatted) file and companion video (MP4) and CADD files (DWG & DXF) for laser cutting the ETSU-developed alternate top bracing designs and marking templates for the STEM Guitar Project’s BBT (OM-sized) standard acoustic guitar kit. The three (3) alternative BBT top bracing designs in this release are
(a) a one-piece base for the standard kit's (Martin-style) bracing,
(b) 277 Ladder-style bracing, and
(c) an X-braced fan-style bracing similar to traditional European or so-called 'classical' acoustic guitars.

The CADD data set for each of the three (3) top bracing designs includes …

Bbt Side Mold Assy, Bill Hemphill

STEM Guitar Project’s BBT Acoustic Kit

This electronic document file set covers the design and fabrication information of the ETSU Guitar Building Project’s BBT (OM-sized) Side Mold Assy for use with the STEM Guitar Project’s standard acoustic guitar kit. The extended 'as built' data set contains an overview file and companion video, the 'parent' CADD drawing, CADD data for laser etching and cutting a drill &/or layout template, CADD drawings in AutoCAD .DWG and .DXF R12 formats of the centerline tool paths for creating the mold assembly pieces on an AXYZ CNC router, and support documentation for CAM applications including router bit specifications, feeds, speed, multi-pass …

Synthesis, Fabrication, And Assembly Of Mesoscale Polymer Filaments, Dylan M. Barber

Doctoral Dissertations

Mesoscale materials, with feature sizes in the range of one hundred nanometers to tens of micrometers, are ubiquitous in Nature. In organisms, mesoscale building blocks connect the properties of underlying molecular and nanoscructures to those of macroscale, organism-scale materials through hierarchical assemblies of recurring structural motifs. The collective action of large numbers of mesoscale features can afford stunning features like the structural color of the morpho butterfly wing, calcium ion-mediated movement in muscle, and wood structures like xylem that can support enormous external compressive loads and negative internal pressure to transport nutrients throughout an organism. In synthetic systems, the design, …

Source Data For Self-Spinning Filaments For Autonomously Linked Microfibers, Dylan M. Barber, Todd S. Emrick, Gregory Grason, Alfred Crosby

Data and Datasets

Filamentous bundles are ubiquitous in Nature, achieving highly adaptive functions and structural integrity from assembly of diverse mesoscale supramolecular elements. Engineering routes to synthetic, topologically integrated analogs demands precisely coordinated control of multiple filaments’ shapes and positions, a major challenge when performed without complex machinery or labor-intensive processing. Here, we demonstrate a photocreasing design that encodes local curvature and twist into mesoscale polymer filaments, enabling their programmed transformation into target 3-dimensional geometries. Importantly, patterned photocreasing of filament arrays drives autonomous spinning to form linked filament bundles that are highly entangled and structurally robust. In individual filaments, photocreases unlock paths 16 …

Hybridization From Guest-Host Interactions Reduces The Thermal Conductivity Of Metal-Organic Frameworks, Mallory E. Decoster, Hasan Babaei, Sangeun S. Jung, Zeinab M. Hassan, John T. Gaskins, Ashutosh Giri, Emma M. Tiernan, John A. Tomko, Helmut Baumgart, Pamela M. Norris, Alan J.H. Mcgaughey, Christopher E. Wilmer, Engelbert Redel, Gaurav Giri, Patrick E. Hopkins

Electrical & Computer Engineering Faculty Publications

We experimentally and theoretically investigate the thermal conductivity and mechanical properties of polycrystalline HKUST-1 metal–organic frameworks (MOFs) infiltrated with three guest molecules: tetracyanoquinodimethane (TCNQ), 2,3,5,6-tetrafluoro-7,7,8,8-tetracyanoquinodimethane (F4-TCNQ), and (cyclohexane-1,4-diylidene)dimalononitrile (H4-TCNQ). This allows for modification of the interaction strength between the guest and host, presenting an opportunity to study the fundamental atomic scale mechanisms of how guest molecules impact the thermal conductivity of large unit cell porous crystals. The thermal conductivities of the guest@MOF systems decrease significantly, by on average a factor of 4, for all infiltrated samples as compared to the uninfiltrated, pristine HKUST-1. This reduction in thermal conductivity goes in …

Characterization Of A Three-Way Catalyst For High Efficiency Spark Ignition Engines, Cavin Hesketh

Electronic Theses and Dissertations

The push for environmental protection and sustainability has led to strict emission regulations for automotive manufacturers as evident in EURO VII and 2026 EPA requirements set to take effect in the coming years. The modern gasoline spark ignition (SI) engine typically employs various in-cylinder emission reduction techniques along with an exhaust after-treatment system to comply with emission standards. The three-way catalyst (TWC) is wholly responsible for removing the engine-out emissions including hydrocarbons (HC), carbon monoxide (CO) and nitrogen oxides (NOx). The main objective of this thesis is to investigate the impact of extensive exhaust gas recirculation (EGR) on …

Identification Of Phosphorous Loading Point Source Facilities To 303(D) Listed Nutrient Impaired Waters Through Watershed Delineation Using Arcgis For Life Cycle Assessment Applications, John Zimmerman

Chemical Engineering Undergraduate Honors Theses

The work done for this project is part of a larger “life cycle assessment (LCA) of novel electrochemical phosphorus recovery technology at the wastewater treatment plant and U.S. watershed scales” (Morrissey 2019). The goal of that LCA is to determine “environmental impacts of implementing electrochemical struvite recovery at the wastewater treatment plant, U.S watershed, and global scales” (Morrissey 2019). This project’s goal is to identify locations deemed more sensitive to eutrophication impacts. The results will be used as part of the life cycle inventory (LCI) accounting for geographically explicit phosphorus flows. The waters identified as impaired were sourced from the …

Advanced Materials Design Using Application-Based Processing Techniques, Daniel S. Camarda

Doctoral Dissertations

This dissertation pertains to generating advanced materials using application-based processing techniques. First, billets consisting of PTFE sintering powders are evaluated using Thermomechancal Analysis. It was found that both shape change and volume change are associated with enthalpic and entropic recoil, respectively. These phenomena, due to melting and stored energy during the powder compaction process, were found to be molecular weight dependent. Additionally, kinetics of the recovery and sintering process were found to be slower in blended specimens than pure samples. Next, the creation of graft copolymers by selectively grafting a second polymer to the amorphous fraction of a semi-crystalline polymer …

Creation Of A Cip Method For The Heat Exchangers At Rolls-Royce, Melanie Howe, Austin Williams, Caroline Dempsey, Bethany Fralick

Journal of the South Carolina Academy of Science

Rolls-Royce produces various engines which must be tested prior to their distribution to ensure a high-quality product. The manufacturing plant contains four test cells where the engines can be subjected to high levels of torque and extreme temperatures. A heat exchanger is necessary in this testing system and over time, unwanted waste accumulates on the system’s plates. The team is tasked with developing and implementing a system mounted on a mobile cart which can provide data to determine whether the plates need to be cleaned. For this cleaning system to work, it must fully saturate the heat exchanger in cleaning …

Development Of Advanced Solid-State Electrolytes And Interfaces For High-Performance Sulfide-Based All-Solid-State Lithium Batteries, Feipeng Zhao

Electronic Thesis and Dissertation Repository

All-solid-state lithium batteries (ASSLBs) have become increasingly attractive due to the demand of high-energy-density and high-safety lithium-ion batteries for electric vehicles (EVs). As the core component of ASSLBs, solid-state electrolytes (SSEs) are regarded as essential to determine the electrochemical performance of ASSLBs. The inorganic SSEs is one of the most important categories in all developed SSEs, representing the advance of superionic lithium conductors as well as the cornerstone to construct flexible polymer/inorganic composite SSEs. The sulfide-based inorganic SSE is one of the most promising SSEs that is receiving a lot of attentions, because only sulfide SSEs can show ultrahigh ionic …

Thermoelectric Transport In Disordered Organic And Inorganic Semiconductors, Meenakshi Upadhyaya

Doctoral Dissertations

The need for alternative energy sources has led to extensive research on optimizing the conversion efficiency of thermoelectric (TE) materials. TE efficiency is governed by figure-of-merit (ZT) and it has been an enormously challenging task to increase ZT > 1 despite decades of research due to the interdependence of material properties. Most doped inorganic semiconductors have a high electrical conductivity and moderate Seebeck coefficient, but ZT is still limited by their high lattice thermal conductivity. One approach to address this problem is to decrease thermal conductivity by means of alloying and nanostructuring, another is to consider materials with an inherently low …

Phase-Field Modeling Of The Polymer Membrane Formation Process For Micro- And Ultra-Filtration, Michael Rosario Cervellere

Graduate Theses and Dissertations

Porous polymer membrane filters are widely used in separation and filtration process. Micro- and ultra-filtration membranes are commonly used in biopharmaceutical applications such as filtering viruses and separating proteins from a carrier solution. The formation of these membrane filters via phase inversion is a complex and interconnected process where varying casting conditions can have a wide variety of effects on the final membrane morphol- ogy. Tailoring membrane filters for specific performance characteristics is a tedious and time consuming process. The time and length scales of membrane formation make it extremely difficult to experimentally observe membrane formation. Modeling the membrane formation …

Effects Of Air Pollution, Temperature And Moisture Content On Copper And Silver Corrosions And The Reliability Of Data Center Equipment, Rui Zhang

Dissertations - ALL

The effects of moisture content, temperature, and pollutant mixture on atmospheric corrosion of copper and silver were investigated by exposing test specimens to different environmental conditions, followed by surface characterization using the coulometric reduction, Scanning Electron Microscopy, and Energy Dispersive Spectrometry (SEM/EDS). Printed circuit board test cards (PCBs) with bare copper were also used to investigate the effects of voltage bias on the PCBs on the corrosion rate. The test specimens were exposed to mixed flowing gases (MFG) environment with eight different combinations of the following five pollutants at the fixed concentration levels: 60 ppb O3, 80 ppb NO2, 40 …