Mechanical Engineering Commons^™

Effects Of Air Pollution, Temperature And Moisture Content On Copper And Silver Corrosions And The Reliability Of Data Center Equipment, Rui Zhang

Dissertations - ALL

The effects of moisture content, temperature, and pollutant mixture on atmospheric corrosion of copper and silver were investigated by exposing test specimens to different environmental conditions, followed by surface characterization using the coulometric reduction, Scanning Electron Microscopy, and Energy Dispersive Spectrometry (SEM/EDS). Printed circuit board test cards (PCBs) with bare copper were also used to investigate the effects of voltage bias on the PCBs on the corrosion rate. The test specimens were exposed to mixed flowing gases (MFG) environment with eight different combinations of the following five pollutants at the fixed concentration levels: 60 ppb O3, 80 ppb NO2, 40 …

Synthesis And Characterization Of Functiona Materials For 3d Printed Composites, Elizabeth Irene Reza

Open Access Theses & Dissertations

The following body of work encompasses the synThesis, upscaling, additive manufacturing, and characterization of microspheres as functional fillers incorporated into polymer syntactic foams. Synthesizing microspheres permits control over morphology, dispersion of particles, and size while the use of direct write manufacturing allowed for the controllability of filler orientation. Two different syntactic foams were developed from similar methodologies: (1) a silicone syntactic foam (2) epoxy syntactic foam. The silicone epoxy foam showed an increasing in damping and elastic modulus. The epoxy syntactic foams showed an enhanced thermal and electrical properties.

Numerical Reconstruction Of Spalled Particle Trajectories In An Arc-Jet Environment, Raghava S. C. Davuluri, Sean C. C. Bailey, Kaveh A. Tagavi, Alexandre Martin

Mechanical Engineering Faculty Publications

To evaluate the effects of spallation on ablative material, it is necessary to evaluate the mass loss. To do so, a Lagrangian particle trajectory code is used to reconstruct trajectories that match the experimental data for all kinematic parameters. The results from spallation experiments conducted at the NASA HYMETS facility over a wedge sample were used. A data-driven adaptive methodology was used to adapts the ejection parameters until the numerical trajectory matches the experimental data. The preliminary reconstruction results show that the size of the particles seemed to be correlated with the location of the ejection event. The size of …

Nebulizer-Based Systems To Improve Pharmaceutical Aerosol Delivery To The Lungs, Benjamin M. Spence

Theses and Dissertations

Combining vibrating mesh nebulizers with additional new technologies leads to substantial improvements in pharmaceutical aerosol delivery to the lungs across therapeutic administration methods. In this dissertation, streamlined components, aerosol administration synchronization, and/or Excipient Enhanced Growth (EEG) technologies were utilized to develop and test several novel devices and aerosol delivery systems. The first focus of this work was to improve the poor delivery efficiency, e.g., 3.6% of nominal dose (Dugernier et al. 2017), of aerosolized medication administration to adult human subjects concurrent with high flow nasal cannula (HFNC) therapy, a form of continuous-flow non-invasive ventilation (NIV). The developed Low-Volume Mixer-Heater (LVMH) …

Effect Of Heat Treatment On Microstructure And Hardness Of A Worn Rail Repaired Using Laser Powder Deposition, Ershad Mortazavian, Zhiyong Wang, Hualiang Teng

Mechanical Engineering Faculty Research

The frequent replacement of worn rails on tracks brings an immense economic burden on the railroad industry, and also causes significant interruptions to railroad operation. Restoration of worn rails via laser powder deposition (LPD) can considerably reduce the associated maintenance costs. This study was focused on the use of LPD to repair the worn profile of a standard U.S. rail. The microstructure of the 304L stainless steel deposits with a minimum hardness of 85 HRB was composed of austenite, δ-ferrite, and sigma. Micropores were dispersed throughout the deposit, and microcracks were found at the rail-deposition interface. The pearlitic rail substrate …

Coaxially Electrospun Fibrous Polymer Scaffolds For Tissue Regeneration And Drug Delivery, Matthew Michael Kleszynski

Graduate Research Theses & Dissertations

A biomaterial is a substance that is specifically engineered to take on a role within the body, either alone or in conjunction with other materials, with the purpose of influencing the body. Using Polymers as a biomaterial is an exciting field of study that has the potential to further our abilities to help those in need. Creating composite nanofibrous scaffolds composed of hydrophobic and hydrophilic polymers may outperform structures made of a single polymer in both in vitro and in vivo environments. Hydrophilicity governs the behavior of polymers in the body and has influence over the mechanical properties of the …

Development Of Synthetic Coal Char Simulant For Microwave Conversion Studies: A Computationally-Driven Approach, Kevin A. Hager

Graduate Theses, Dissertations, and Problem Reports

Recent experimental demonstration of new reaction windows for coal char/methane reactions that are less energy-intensive, provides innovation for modular reactors. However, the correlation of the exact mechanism for the enhancement of these reaction windows is not certain. This study investigates the simplification of these experimental studies by developing a well-characterized coal char simulant. The approach involves using a computational approach to screen macroscopic composition to replicate the dielectric and compositional response of actual char. This study is focused on PRB coal char. A discrete element method (DEM) technique was used to simulate the packing of coal chars to give the …

Application Of A Small Unmanned Aerial System To Measure Ammonia Emissions From A Pilot Amine-Co2 Capture System, Travis J. Schuyler, Bradley Irvin, Keemia Abad, Jesse G. Thompson, Kunlei Liu, Marcelo I. Guzman

Chemistry Faculty Publications

The quantification of atmospheric gases with small unmanned aerial systems (sUAS) is expanding the ability to safely perform environmental monitoring tasks and quickly evaluate the impact of technologies. In this work, a calibrated sUAS is used to quantify the emissions of ammonia (NH₃) gas from the exit stack a 0.1 MWth pilot-scale carbon capture system (CCS) employing a 5 M monoethanolamine (MEA) solvent to scrub CO₂ from coal combustion flue gas. A comparison of the results using the sUAS against the ion chromatography technique with the EPA CTM-027 method for the standard emission sampling of NH_{3 …}

Practical Adhesion Measurements In Organic Coatings; Advancing Understanding And Mechanical Methods Development, Diana Gottschalk

Dissertations

“Adhesion” can be considered either a mechanical or chemical phenomenon. The mechanical interpretation describes the difficulty of separating surfaces and is useful for quantifying performance within applications that depend on bulk and interfacial properties. Chemical adhesion describes interfacial resistance to chemical attack and does not depend on bulk properties. Predicting chemical failure through mechanical measurement is confounded by the influence of bulk properties. However, the prospect is attractive because of the robust tolerance for sample geometries, allowing experiments to resemble an end-use system. The present work's primary goal was to elevate mechanical methods to provide a detailed interfacial characterization of …

Near Simultaneous Laser Scanning Confocal And Atomic Force Microscopy (Conpokal) On Live Cells, Joree N. Sandin, Surya P. Aryal, Thomas E. Wilkop, Christopher I. Richards, Martha E. Grady

Physiology Faculty Publications

Techniques available for micro- and nano-scale mechanical characterization have exploded in the last few decades. From further development of the scanning and transmission electron microscope, to the invention of atomic force microscopy, and advances in fluorescent imaging, there have been substantial gains in technologies that enable the study of small materials. Conpokal is a portmanteau that combines confocal microscopy with atomic force microscopy (AFM), where a probe "pokes" the surface. Although each technique is extremely effective for the qualitative and/or quantitative image collection on their own, Conpokal provides the capability to test with blended fluorescence imaging and mechanical characterization. Designed …

University Of Kentucky Measurements Of Wind, Temperature, Pressure And Humidity In Support Of Lapse-Rate Using Multisite Fixed-Wing And Rotorcraft Unmanned Aerial Systems, Sean C. C. Bailey, Michael P. Sama, Caleb A. Canter, Luis Felipe Pampolini, Zachary S. Lippay, Travis J. Schuyler, Jonathan D. Hamilton, Sean B. Macphee, Isaac S. Rowe, Christopher D. Sanders, Virginia G. Smith, Christina N. Vezzi, Harrison M. Wight, Jesse B. Hoagg, Marcelo I. Guzman, Suzanne Weaver Smith

Mechanical Engineering Faculty Publications

In July 2018, unmanned aerial systems (UASs) were deployed to measure the properties of the lower atmosphere within the San Luis Valley, an elevated valley in Colorado, USA, as part of the Lower Atmospheric Profiling Studies at Elevation – a Remotely-piloted Aircraft Team Experiment (LAPSE-RATE). Measurement objectives included detailing boundary layer transition, canyon cold-air drainage and convection initiation within the valley. Details of the contribution to LAPSE-RATE made by the University of Kentucky are provided here, which include measurements by seven different fixed-wing and rotorcraft UASs totaling over 178 flights with validated data. The data from these coordinated UAS flights …

Development Of An Advanced Zinc Air Flow Battery System (Phase 2), Jingyu Si

Theses and Dissertations

A zinc-air battery is the promising energy storage technology for large-scale energy storage applications due to its low cost, environmental friendliness, and high energy density. However, the electrically rechargeable zinc−air batteries suffer from poor energy efficiency and cycle life because of critical problems such as passivation, dendrite growth, and hydrogen evolution reaction. The proliferation of zinc−air batteries is limited.

The zinc-air flow battery combines the advantages of both a zinc-air battery and a redox flow battery. This combination permits the zinc-air flow battery to compete with the current leading battery technologies in the marketplace. A rechargeable Zn-air flow battery with …

Enhancement Of Phase Change Material Sorbitol By Nanoparticle Inclusion For Improving Thermal Energy Storage Capabilities, Joshua Kasitz

Mechanical Engineering Undergraduate Honors Theses

Thermal management of electronic devices has become an increasingly vital field of study with the rapid miniaturization of many key electrical components. With the significant improvement of semiconductor manufacturing and intensified focus on interconnects, electronic devices have decreased in size at an incredible rate. Decreasing spatial requirements is essential to improving device capabilities as the electronic system is able to incorporate more components. Currently, electronic systems are drastically limited by the capabilities of their cooling mechanisms. Smaller devices lead to large increases in the energy density of the system and require more powerful cooling systems to maintain proper component operating …

Carbon Oxidation At The Atomic Level: A Computational Study On Oxidative Graphene Etching And Pitting Of Graphitic Carbon Surfaces, Simon Schmitt

Theses and Dissertations--Mechanical Engineering

In order to understand the oxidation of solid carbon materials by oxygen-containing gases, carbon oxidation has to be studied on the atomic level where the surface reactions occur. Graphene and graphite are etched by oxygen to form characteristic pits that are scattered across the material surface, and pitting in turn leads to microstructural changes that determine the macroscopic oxidation behavior. While this is a well-documented phenomenon, it is heretofore poorly understood due to the notorious difficulty of experiments and a lack of comprehensive computational studies. The main objective of the present work is the development of a computational framework from …

Correlating The Physicochemical Properties Of Magnesium Stearate With Tablet Dissolution And Lubrication, Julie L. Calahan

Theses and Dissertations--Pharmacy

Magnesium stearate (MgSt) is the most commonly used pharmaceutical excipient and is present in over half the tablet formulations on the market. In spite of its popularity as an effective lubricant, it has been repeatedly recognized that there is significant variability between MgSt samples, which can cause inconsistent lubrication between batches of MgSt. The hypothesis of this research is that the batch-to-batch variability in tablet lubrication and dissolution observed in tablet formulations containing different MgSt samples can be correlated with differences in MgSt physicochemical properties (fatty acid salt composition, crystal hydrate form, particle size and surface area). Developing correlations between …

Analytical Approach To Investigation Of Free Vibration Of Thin Rectangular Plate Immersed In Fluid, Resting On Winkler And Pasternak Foundations, Obanishola Sadiq, Gbeminiyi Sobamowo, Saheed Salawu

Karbala International Journal of Modern Science

Dynamic behaviour of free vibration of rectangular plate is investigated. This study considered an analytical approach to investigation of free vibration of thin rectangular plate immersed in fluid, resting on Winkler and Pasternak foundations.The governing nonlinear partial differential equation is analyzed using two-dimensional differential transform method. The accuracy of the analytical solutions obtained is verified with existing results in literature and confirmed in excellent agreement. Thereafter, the analytical solutions are used for investigation of effect of elastic foundation, fluid and aspect ratio on vibrating plate.From the result, it is observed that, increase elastic foundation parameters increases natural frequency, increase aspect …

Pre-Methylation Of Lignin To Improve Storage Stability Of Oil Produced By Solvent Liquefaction, Jae-Young Kim, Parinaz Hafezi-Sefat, Sarah D. Cady, Ryan G. Smith, Robert C. Brown

Sarah Cady

In this study, we methylated hydroxyl groups (phenolic hydroxyl: Phe-OH and aliphatic hydroxyl: Aliph-OH) in soda lignin (SL) prior to solvent liquefaction to improve storage stability of the resulting oil. We investigated two methylating reagents, dimethyl sulfate (DMS) and dimethyl carbonate (DMC), for selective Phe-OH and total hydroxyl group (Phe-OH and Aliph-OH) blocking. Samples of SL, DMS-SL, and DMC-SL were depolymerized into oils under supercritical ethanol (350 °C). Both methylated lignins produced higher amounts of oils and smaller amounts of char compared to untreated SL due to suppressed charring reactions. Oil produced from SL had relatively higher functional group contents …

Development Of A Ground-Based Aerial-Tracking Instrument For Open-Path Spectroscopy To Monitor Atmospheric Constituents, Haden Hodges

Civil Engineering Undergraduate Honors Theses

A ground-based aerial-tracking instrument, known as the Ground Tracker, designed to provide spectral data to quantify greenhouse gases is under development. The Ground Tracker includes an Optical System including a high power rifle scope, video camera, and spectrometer used to locate an active light source from the Emitter, and collect spectral data by utilizing an actuating mirror. The implementation of this instrument could be made low cost by utilizing existing weather balloon infrastructure to allow the Emitter to be placed into the lower stratosphere. The recovery of the emitter will be possible by tracking the GPS coordinates. Weather balloon instrument …

Computational Studies Of Thermal Properties And Desalination Performance Of Low-Dimensional Materials, Yang Hong

Department of Chemistry: Dissertations, Theses, and Student Research

During the last 30 years, microelectronic devices have been continuously designed and developed with smaller size and yet more functionalities. Today, hundreds of millions of transistors and complementary metal-oxide-semiconductor cells can be designed and integrated on a single microchip through 3D packaging and chip stacking technology. A large amount of heat will be generated in a limited space during the operation of microchips. Moreover, there is a high possibility of hot spots due to non-uniform integrated circuit design patterns as some core parts of a microchip work harder than other memory parts. This issue becomes acute as stacked microchips get …

Non-Einstein Viscosity Phenomenon Of Acrylonitrile–Butadiene–Styrene Composites Containing Lignin–Polycaprolactone Particulates Highly Dispersed By High-Shear Stress, Sing-Hoon Kim, Kisuk Choi, Kyouk Ryeol Choi, Taesung Kim, Jonghwan Suhr, Kwang Jin Kim, Hyoung Jin Choi, Jae-Do Nam

Mechanical Engineering Faculty Research

Lignin powder was modified via ring-opening polymerization of caprolactone to form a lignin–polycaprolactone (LPCL) particulate. The LPCL particulates were mixed with an acrylonitrile–butadiene–styrene (ABS) matrix at an extremely high rotational speed of up to 3000 rpm, which was achieved by a closed-loop screw mixer and in-line melt extruder. Using this high-shear extruding mixer, the LPCL particulate size was controlled in the range of 3395 nm (conventional twin-screw extrusion) down to 638 nm (high-shear mixer of 3000 rpm) by altering the mixing speed and time. The resulting LPCL/ABS composites clearly showed non-Einstein viscosity phenomena, exhibiting reduced viscosity (2130 Pa·s) compared to …

Fracture Toughness And Fatigue Crack Growth Rate Characterization Of Inconel 718 Formed By Laser Powder Bed Fusion, Charles C. Hohnbaum

Theses and Dissertations

Continuing improvement in the field of AM of metals provides the opportunity for direct fabrication of aerospace parts. AM was once used in large part for rapid prototyping but improvements in technology and increases in the knowledge base of AM materials has provided the opportunity for manufacture of AM parts for operational use. The ability to create low numbers of unique parts without having to invest in expensive tooling provides great economic incentive to utilize this technique. IN718 is the most common high temperature alloy used in the aerospace industry and lends itself readily to formation by LPBF. The superior …

Process Parameter Development Of Additively Manufactured Af9628 Weapons Steel, Erin M. Hager

Theses and Dissertations

The manufacture of components in Additive Manufacturing processes is limited by the range of materials available. Qualification of materials for Additive Manufacturing is time intensive, and is often specific to a single type of machine. In this study, an approach to selecting power, speed, and hatch spacing values for a newly powderized material, AF9628 weapons steel, is described that results in highly dense (>99.9%) parts on an MLab 200R Cusing. Initial power and speed values used in a weld track study were selected based on a survey of parameters used on similar materials, with a focus on the energy …

Oxidative Degradation Of Lignin And Investigation Of Utilization Of Lignin-Derived Materials As Building Blocks For Epoxy Resins, Zhen Fang

Theses and Dissertations--Chemistry

Lignin, the second most abundant biopolymer on earth, is potentially a replaceable source for bulky fuels and chemical feedstocks. There have been numerous reports on methods for the oxidative cleavage of β-O-4 linkages but relatively few reports of how those methods affect other linkages that are present in lignin. We investigated how the β-1 and β-5 linkages respond under oxidative conditions proposed for lignin deconstruction based on their effect on β-O-4 linkages. Mechanochemical treatment of lignin can greatly improve the yield of monomer products and we applied a mechanochemical approach, using powerful ring-and-puck milling to promote lignin degradation. Along with …

Call For Abstracts - Resrb 2019, July 8-9, Wrocław, Poland, Wojciech M. Budzianowski

Wojciech Budzianowski

No abstract provided.

Development And Thermodynamic Analysis Of An Integrated Mild/Partial Gasification Combined Cycle (Impgc) Under Green And Brown Field Conditions With And Without Carbon Capture, Henry A. Long Iii

University of New Orleans Theses and Dissertations

Coal is a very prominent energy source in the world, but it is environmentally unattractive due to its high sulfur and ash content as well as its alleged contribution towards climate change, but it is affordable, abundant, and has high energy content. Thus, utilizing coal in a cleaner and more efficient way has become necessary. One promising clean coal technology involves fully gasifying coal into synthesis gas, cleaning it, and feeding it into a high-efficiency combined cycle, such as an Integrated Gasification Combined Cycle (IGCC). Inspired by the recent success of warn gas cleanup (WGCU), mild and partial gasification are …

Optimization Of Superhydrophobic Surface Production Using Ambient-Dried Silica-Based Aerogels, Elizabeth Donlon

Honors Theses

Superhydrophobic surfaces exhibit particular properties that make them functional in various anti-sticking, anti-contamination, self-cleaning and drag reduction applications. Though such surfaces are found in nature - most notably the lotus leaf - they are difficult to produce. There are numerous methods and techniques for fabricating superhydrophobic surfaces. One such method is the sol-gel method, in which aerogel, a highly porous and lightweight material that can be made hydrophobic or superhydrophobic, is coated onto a surface. The purpose of this project is to devise a simple and repeatable procedure for making hydrophobic silica aerogel coatings that can be used for drag …

Kinetic Study Of Free Radical-Radical Reactions Of Combustion Importance At Elevated Pressures, Chao Yan

Dissertations

Combustion mechanisms consist of hundreds elementary reactions of free radicals and stable molecules. Radical-radical elementary reactions play important roles due to the high concentration in which free radicals are accumulated in combustion systems. Radical-radical reactions are typically multi-channel. Some of the channels might be of chain propagation or even chain branching nature, while other channels might be of chain termination nature. The relative importance of different channels is pressure dependent. Compared to radical-molecule reactions, radical-radical reactions are much less studied. This is due to the difficulties of well characterized quantitative production of radical species as well as due to the …

Development Of Microdialysis Probes In Series Approach Toward Eliminating Microdialysis Sampling Calibration: Miniaturization Into A Pdms Microfluidic Device, Randy Espinal Cabrera

Graduate Theses and Dissertations

A new microdialysis sampling method and microfluidic device were developed in vitro. The method consisted of using up to four microdialysis sampling probes connected in series to evaluate the relative recovery (RR) of different model solutes methyl orange, fluorescein isothiocyanate (FITC)-dextran average mol. wt. 4,000 (FITC-4), FITC-10, FITC-20, and FITC-40. Different flow rates (0.8, 1.0, and 1.5 µL/min) were used to compare experimentally observed relative recoveries with theoretical estimations. With increasing the number of probes in series, the relative recovery increases and ~100% (99.7% ± 0.9%) relative recovery for methyl orange was obtained. For larger molecules such as fluorescein isothiocyanate …

Uncertainty In Combustion Reaction Rates And Its Effects On Combustion Simulations, Joshua Piehl

Wayne State University Theses

This work investigates the uncertainties in reaction rates of an n-dodecane model on turbulent spray combustion simulations. Six major reactions were found to significantly impact the ignition delay of the mechanism in a 0-D batch reactor model. These reactions’ rates were independently modified and placed into individual mechanisms. These newly developed mechanisms were simulated in a 3-D turbulent spray simulation and a 0-D batch reactor at a pressure of 60 bar and temperatures from 900 to 1100 K. The combustion characteristics (e.g. ignition delays, flame lift-off length, liquid and vapor penetration) of the modified mechanisms were compared to those produced …

Low-Carbon Building Skills Website, Faculty Of Applied Science And Technology Sheridan College

Books and Websites

Low-carbon building involves designing, constructing, operating, maintaining, and removing buildings in ways that conserve natural resources and reduce Greenhouse Gas (GHG) emissions. To move towards a low-carbon economy, we need tradespeople who are educated in the design, construction maintenance and operation of buildings, who understand the industrial and constructions sectors, and are trained in low-carbon building skills.

Sheridan College’s participation in the Low Carbon Building Skills (LCBS) project involved developing and delivering low-carbon building skills curriculum across relevant disciplines and involving the full building cycle, from design to operations and optimization. The learning modules address what can be done to …