VLSI and Circuits, Embedded and Hardware Systems Commons^™

A Sindy Hardware Accelerator For Efficient System Identification On Edge Devices, Michael Sean Gallagher

Master's Theses

The SINDy (Sparse Identification of Non-linear Dynamics) algorithm is a method of turning a set of data representing non-linear dynamics into a much smaller set of equations comprised of non-linear functions summed together. This provides a human readable system model the represents the dynamic system analyzed. The SINDy algorithm is important for a variety of applications, including high precision industrial and robotic applications. A Hardware Accelerator was designed to decrease the time spent doing calculations. This thesis proposes an efficient hardware accelerator approach for a broad range of applications that use SINDy and similar system identification algorithms. The accelerator is …

Phone Microwave, Khanh Kim Hoang, Emily Zhou

Computer Engineering

This project involves the installation of remote-control capabilities in an antique 1980s microwave, effectively turning the microwave into a “smart” device. While preserving the original functionality of the microwave, a combination of software and hardware components allows for remote microwave operations. The microwave can be remotely operated by calling the built-in number, and more advanced settings and options can be utilized by texting. The microwave is also secured against unauthorized use with the addition of a PIN code that is required to operate the device.

Design And Analysis Of A Discrete, Pcb-Level Low-Power, Microwave Cross-Coupled Differential Lc Voltage-Controlled Oscillator, Pavin Singh Virdee

Master's Theses

Radio Frequency (RF) and Microwave devices are typically implemented in Integrated Circuit (IC) form to minimize parasitics, increase precision and tolerances, and minimize size. Although IC fabrication for students and independent engineers is cost-prohibitive, an abundance of low-cost, easily accessible printed circuit board (PCB) and electronic component manufacturers allows affordable PCB fabrication.

While nearly all microwave voltage-controlled oscillator (VCO) designs are IC-based, this study presents a discrete PCB-level cross-coupled, differential LC VCO to demonstrate this more affordable and accessible approach. This thesis presents a 65 mW, discrete component VCO PCB with industry-comparable RF performance. A phase noise of -103.7 dBc/Hz …

Mars Prototype Rover Environmental Measurement System, James A. Renick

Computer Engineering

In my senior project, the problem I am trying to solve is how to efficiently design, create, and install an original library onto a Mars prototype rover operating system and to further use that library to integrate a new weather measurement sensor device into the rover system with the necessary software and hardware implementations. This is an important and highly valued problem as many aerospace and other engineering companies utilize rovers and other autonomous systems for important research, explorations, and reconnaissance missions and goals. In solving this problem, I utilized many resources that were available to me such as advisors, …

Signal Adc Converter Simulation On Cadence Virtuoso For Audio Applications, Maxwell Kazuki Fukada

Electrical Engineering

Audio signals are representations of sounds with a mixture of multiple analog signals between the frequency of 20Hz to 20,000Hz. To record snippets of audio data onto a mobile phone or computer, the signal needs to be converted to a digital format. For this purpose, many devices utilize a converter, specifically a sigma-delta modulator with a digital filter. By using a converter, electronics can receive binary data about the audio signal accurately and quickly without losing important signal information. This project aims to simulate a fully functional audio converter with a sigma-delta modulator and decimation filter. The system will receive …

Smartphone Control Of Rc Cars, Weston R. Fitzgerald

Electrical Engineering

The smartphone-controlled RC (remote-controlled) car is an inexpensive remote-controlled car designed to be fast and portable. Instead of manufacturing, packaging, and shipping a separate controller, the remote control is implemented in a phone application, which saves time and money in both the design process and the manufacturing process. Utilizing the user’s smartphone is more cost-effective since mobile devices are a common recurrence, and packaging fewer devices results in overall better portability of the product.

This smartphone-controlled car is speedy and intuitive to learn for typical smartphone users. The user can change the car’s speed and direction wirelessly using their phone; …

Indoor Positioning Using Synchronized Ultrasonic Ofdma Signals, Julian Bartolone

Master's Theses

This paper proposes a method of short-range indoor localization using differential phase measurements of synchronized two-tone ultrasonic signals in an Orthogonal Frequency Multiple Access (OFDMA) scheme. This indoor positioning system (IPS) operates at an ultrasonic frequency of approximately 40kHz and synchronizes using an infrared signal. The OFDMA scheme allows for a receiver to process the signals from multiple transmitters continuously without the signals interfering with each other. The phases of the signals are measured using Goertzel Filters, allowing for low-complexity frequency content analysis. A MATLAB simulation using the proposed localization method is performed using four transmitter nodes in the corners …

Tractor Hacking, Jin Huang, Kyle B. Kesler

Electrical Engineering

Tractor hacking arose from tractor owners' desire for full control over the tractors they purchase. Tractor manufacturers set strict security on the electrical components of their tractors, making it difficult for tractor owners to diagnose and monitor their tractors on their own. The UltraBlue Tractor Hacking project is a solution to this problem, allowing tractor owners to perform diagnostics and monitor the equipment they purchased without having to go through dealerships. From talking to farmers, we found that they valued a diagnostic tool that allows for clearing and resetting Diagnostic Trouble Codes (DTCs), viewing diagnostic data pertaining to a specific …

Design And Characterization Of Standard Cell Library Using Finfets, Phanindra Datta Sadhu

Master's Theses

The processors and digital circuits designed today contain billions of transistors on a small piece of silicon. As devices are becoming smaller, slimmer, faster, and more efficient, the transistors also have to keep up with the demands and needs of the daily user. Unfortunately, the CMOS technology has reached its limit and cannot be used to scale down due to the transistor's breakdown caused by short channel effects. An alternative solution to this is the FinFET transistor technology, where the gate of the transistor is a three dimensional fin that surrounds the transistor and prevents the breakdown caused by scaling …

Design Of An Ultra-Wideband Frequency-Modulated Continuous Wave Short Range Radar System For Extending Independent Living, Toai-Chi Nguyen

Master's Theses

Falls in the disabled and elderly people have been a cause of concern as they can be immobilized by the fall and have no way to contact others and seek assistance. The proposed frequency modulated continuous wave (FMCW) short range radar (SRR) system, which uses ultra-wideband (UWB) signals can provide immediate assistance by monitoring and detecting fall events. The unique characteristics of this system allow for a frequency-based modulation system to carry out triangulation and sense the location of the fall through the usage of a continuous chirp signal that linearly sweeps frequency. This project focuses on the development, design …

Polyone Smartphone, Joshua Zalmanowitz, Chi Nguyen, Gerome Cacho, Chris Lim

Electrical Engineering

The Poly One Smartphone is a student designed smartphone built to explore the implementation of 5G, provide a hardware solution to ensure personal information security and privacy, and provide longer battery life. The key features of this smartphone include but are not limited to a main cpu, some form of network connectivity in the form of Wi-fi or Cellular Data, calling functionality, a rechargeable battery that works with common power connection protocols, and compatibility with popular applications.

Weight Controlled Electric Skateboard, Zachary Barram, Carson Bertozzi, Vishnu Dodballapur

Computer Engineering

Technology and the way that humans interact is becoming more vital and omnipresent with every passing day. However, human interface device designers suffer from the increasingly popular “designed for me or people like me” syndrome. This design philosophy inherently limits accessibility and usability of technology to those like the designer. This places severe limits of usability to those who are not fully able as well as leaves non-traditional human interface devices unexplored. This project set out to explore a previously uncharted human interface device, on an electric skateboard, and compare it send user experience with industry leading human interface devices.

Dashboard, Bradley Manuel Levin, Kyle Matthew King

Computer Engineering

Modern gamers are always looking for new and exciting ways to play board games. Our senior project, DashBoard, is intended to capitalize on this interest and upgrade board games to have pre-programmed moves and easy piece moving. It is a proof-of-concept project for a programmable chess-style game board using an electromagnet array to move the pieces around the board. With an easily programmable interface with the Raspberry Pi 3, users can make their own programs or find ones others have made online to move pieces in creative ways.

Flight Director Embedded System And Mobile Ios Application, Anthony Epshteyn

Computer Engineering

For my senior project, I was asked to assist an Aerospace Engineering professor with the design of his new glider. He needed to create a flight director-type instrument so that his pilot could get the aircraft’s positional data during flight. This positional data came from a powerful sensor mounted on the fuselage. To interface with the sensor, I created an embedded system comprised of a ESP32 micro-controller communicating with the sensor via UART/RS-232. The micro-controller was mounted on a breadboard and connected to the sensor via jumper wires. The ESP32 featured a Bluetooth chip that allowed for communication using the …

Tidalsim Senior Project Report, Kent Zhang, Colin Vandervoort

Computer Engineering

Throughout the course of this project, our team helped the Cal Poly Biological Sciences department refine an intertidal zone simulator. The aim of this device is to allow any marine biologist to easily simulate a vast range of tidal zones in order to test animal behaviors within these zones. Another goal of this project is to make each simulation tank independent from the others by using a single microcontroller to handle all inputs and outputs of the system as well as logging all relevant data. The current system is set up so that a separate microcontroller handles dissolved oxygen and …

Analog Single Sideband-Pulse Width Modulation Processor For Parametric Acoustic Arrays, Vikrant A. Marathe

Master's Theses

Parametric acoustic arrays are ultrasonic-based loudspeakers that produce highly directive audio. The audio must first be preprocessed and modulated into an ultrasonic carrier before being emitted into the air, where it will self-demodulate in the far field. The resulting audio wave is proportional to the double time-derivative of the square of the modulation envelope. This thesis presents a fully analog processor which encodes the audio into two Pulse Width Modulated (PWM) signals in quadrature phase and sums them together to produce a Single Sideband (SSB) spectrum around the fundamental frequency of the PWM signals. The two signals are modulated between …

Cmos Design Of An 8-Bit 1ms/S Successive Approximation Register Adc, Ameya Vivekanand Ganguli

Master's Theses

Rapid evolution of integrated circuit technologies has paved a way to develop smaller and energy efficient biomedical devices which has put stringent requirements on data acquisition systems. These implantable devices are compact and have a very small footprint. Once implanted these devices need to rely on non-rechargeable batteries to sustain a life span of up to 10 years. Analog-to-digital converters (ADCs) are key components in these power limited systems. Therefore, development of ADCs with medium resolution (8-10 bits) and sampling rate (1 MHz) have been of great importance.

This thesis presents an 8-bit successive approximation register (SAR) ADC incorporating an …

Experimental Study And Modeling Of The Gm-I Dependence Of Long-Channel Mosfets, Michael Fong Cheng

Master's Theses

This thesis describes an experimental study and modeling of the current-transconductance dependence of the ALD1106, ALD1107, and CD4007 arrays. The study tests the hypothesis that the I-gm dependence of these 7.8 µm to 10 µm MOSFETs conforms to the Advanced Compact Model (ACM). Results from performed measurements, however, do not support this expectation. Despite the relatively large length, both ALD1106 and ALD1107 show sufficiently pronounced ‘short-channel’ effects to render the ACM inadequate. As a byproduct of this effort, we confirmed the modified ACM equation. With an m factor of approximately 0.6, it captures the I-gm dependence with sub-28% maximum error …

Asic Design Of Rf Energy Harvester Using 0.13um Cmos Technology, Jainish K. Zaveri

Master's Theses

Recent advances in wireless sensor nodes, data acquisition devices, wearable and implantable medical devices have paved way for low power (sub 50uW) devices. These devices generally use small solid state or thin film batteries for power supply which need replacement or need to be removed for charging. RF energy harvesting technology can be used to charge these batteries without the need to remove the battery from the device, thus providing a sustainable power supply. In other cases, a battery can become unnecessary altogether. This enables us to deploy wireless network nodes in places where regular physical access to the nodes …

Genetic Algorithm Amplifier Biasing System (Gaabs): Genetic Algorithm For Biasing On Differential Analog Amplifiers, Sean Whalen

Computer Engineering

Genetic Algorithm Amplifier Biasing System (GAABS) - Senior Project Analysis

Summary of Functional Requirements

This project integrates LTSpice with a python script that runs a genetic algorithm to bias a differential amplifier. The system biases the amplifier with 2 different voltages, the base voltage for the PNP BJTs of the active loads and a voltage controlling the current of the current sink. The project runs via a python script, gets data from LTSpice’s command line call, and iteratively runs until the system is biased to achieve the greatest gain on an arbitrary input voltage.

Primary Constraints

Some of the main …

Arm Mke1xf Mcu Replatform, Nathan Hong, Derek Lung, Japsimran Singh, Bevin Tang

Computer Engineering

After Cal Poly Racing’s electrical team began to hit the technical limits of the ADC and other I/O features of the current 8-bit Atmel AT90 microcontroller unit, it became clear that an upgrade was due. This replatforming project takes the functionalities of the old, 8-bit architecture, and aims to provide a 32-bit version using the ARM MKE1xF MCU. With the idea of having a working PCB as a stretch goal, the scope of the library development was limited to enable base functionality. Thus, the only libraries developed were for the Timer, ADC, SPI, UART, and CAN. Additionally, this document discusses …

Portable High-Definition Audio Spectrum Analyzer, Alex Zahn, Jamie Corr

Electrical Engineering

The Portable High-definition Audio Spectrum Analyzer (PHASA) allows the user to visualize the audio frequency spectrum of an incoming line-level stereo audio signal. Upon pressing the touch screen spectrum graph, the PHASA displays the corresponding frequency and volume levels as well as crosshairs at the touched location. The PHASA features multiple left/right channel display modes— Left channel only, right channel only, both channels simultaneously, and the average between the two channels. The PHASA features multiple resolution display modes (standard-resolution and high-resolution) and multiple dynamics display modes (standard dynamics, averaging, and peak/hold). The PHASA accepts input audio via a 1/4" TRS …

Metrology Computer Redesign, Natalie Lizama, Melinda Ong, Mitchell Aiken

Electrical Engineering

We are M[EE]² and our project is to redesign Micro-Vu’s metrology computer (the Q16) with modern components and updated firmware. Metrology machines take high precision and high accuracy measurements, and a computer attached to each machine reads out the measurements. We will be redesigning the logic and display circuit boards on the Q16. The ports and communication methods with the machine will stay the same as it must be a drop-in replacement.

The motivation behind the redesign stems from the age of the current design. The current design was created in 1986, and has not had significant modifications since. …

Differential Power Analysis In-Practice For Hardware Implementations Of The Keccak Sponge Function, Nathaniel Graff

Master's Theses

The Keccak Sponge Function is the winner of the National Institute of Standards and Technology (NIST) competition to develop the Secure Hash Algorithm-3 Standard (SHA-3). Prior work has developed reference implementations of the algorithm and described the structures necessary to harden the algorithm against power analysis attacks which can weaken the cryptographic properties of the hash algorithm. This work demonstrates the architectural changes to the reference implementation necessary to achieve the theoretical side channel-resistant structures, compare their efficiency and performance characteristics after synthesis and place-and-route when implementing them on Field Programmable Gate Arrays (FPGAs), publish the resulting implementations under the …

Electronic Drum Machine (E.D.M), Nyssa Marie Backes

Electrical Engineering

Many people argue that a drummer plays the most important role in a band of any genre. During live performances, the other band members rely on the drummer to keep the song moving forward at a proper steady pace. Even in recorded music, drums help listeners sing and dance along with their favorite songs. Thus, achieving success as a band, both in terms of recordings and live shows, absolutely requires a drummer. So, if a band does not have a drummer, and cannot afford the hefty cost of hiring a session drummer, a touring drummer, or both, how can they …

Logic Tiles, Andrew Wheeler, Tristan Lennertz

Computer Engineering

This project was originally conceived by Professor Andrew Danowitz as he considered the restructuring of the introductory digital design course at Cal Poly. As it stands now, students apply their knowledge of boolean algebra and combinatorial logic through the programming of a Field Programmable Gate Array (FPGA) using a Hardware Descriptive Language (HDL). While this is the industry standard for designing large, complex digital circuits, and is an fundamental skill to learn, there is a lack of actual circuit building in the process that can cause a disconnect from theory to application for students who have little-to-no experience with digital …

Smart Safeguard, Stephen J. Marrone

Electrical Engineering

Smart Safeguard is designed to provide people with an affordable device that will notify the authorities when the buyer gets in a car crash. The device will operate off the 12V car power that is present in every car and use an accelerometer to detect if an accident has occurred. If an accident is detected the device will proceed to light up and make a noise until the passenger pushes a button on the device. If the passenger doesn’t push the button within 15 seconds the device, which is wirelessly connected to the passenger’s phone, will initiate a text to …

Remote Cable Gantry, Allen L. Bailey

Electrical Engineering

The Remote Cable Gantry is a robotic system that was initially intended to aid in the art of aerial videography. It was designed to enable novice and expert users alike to capture both video footage and audio from perspectives unachievable by current methods. This system uses a series of cables to control the position of a camera gimbal in a defined 3D space and, as a self-contained unit, is portable and easy to use. The Remote Cable Gantry offers a quiet, intuitive, and safe alternative to existing technology, which has been limiting the market and potential of aerial photography and …

Music Synthesizer Senior Project: Individual Report, Bryan Bellin

Electrical Engineering

No abstract provided.

Music Synthesizer Senior Project: Danalog, Vikrant A. Marathe

Electrical Engineering

The Danalog is a 25 key portable digital music synthesizer that uses multiple synthesis methods and effects to generate sounds. Sound varieties included three synthesis methods including FM, subtractive, and sample-based, with up to eight adjustable parameters, at least four effects, including reverb, chorus, and flange, with five adjustable parameters, and at least two note polyphony, and a five band equalizer. The user would be able to adjust these effects using digital encoders and potentiometers and view the settings on two LCD screens. The finals project was unable to meet the original design requirements. The FM synthesis method was primarily …