Biomedical Engineering and Bioengineering Commons^™

The Effect Of Particle Surface Area To Volume Ratio On Ion Release From Cocr Spheres, Darin J. Grandfield

Master's Theses

In 2005, over 200,000 Americans underwent a hip arthroplasty, the replacement of a hip joint with an artificial prosthesis. Of these arthroplasties, metal-on-metal type implants represent an increasing usage percentage. Metal-on-metal implants are selected largely for their low volumetric wear rate, durability, and resistance to corrosion. In spite of these advantages, little is known concerning the long-term consequences of heavy metal alloy use in the body, although early research indicates potentially carcinogenic results. This thesis is a preliminary investigation into these long term effects and their root causes.

An improved comprehension of the corrosion kinetics and the rate of ion …

Evaluating The Electrical Response Of Polyaniline To Mechanical Strain, Matthew L. Goebel

Master's Theses

This thesis focuses on the electrical output of polyaniline films subjected to uniaxial strain in hydrochloric acid solutions. Polyaniline belongs to novel class of materials known as conducting polymers. Alternating single and double bonds in the backbone of conducting polymers allow them to transmit electric charge when they are doped with negatively charged ions. Modifying the degree of doping and other electrical/chemical treatments allow conducting polymers to exhibit conducting, semi-conducting, or insulating electrical properties. Resilient mechanical properties, good processability, and low cost make conducting polymers good candidates for applications traditionally held by metals and semi-conductors.

When tensile strain is applied …

Design, Fabrication, And Implementation Of A Single-Cell Capture Chamber For A Microfluidic Impedance Sensor, Joshua-Jed Doria Fadriquela

Master's Theses

A microfluidic device was created for single-cell capture and analysis using polydimethylsiloxane (PDMS) channels and a glass substrate to develop a microfluidic single-cell impedance sensor for cell diagnostics. The device was fabricated using photolithography to create a master mold which in turn will use soft lithography to create the PDMS components for constant device production. The commercial software, COMSOLTM Multiphysics, was used to quantify the fluid dynamics in shallow micro-channels.

The device will be able to capture a cell and sequester it long enough to enable measurement of the impedance spectra that can characterize cell. The proposed device will be …

Do Canines Experience The Effects Of Heart Rate Turbulence?, Melanie Ann Gurunathan

Master's Theses

Background

The canine cardiac system has been the model against which many Class III cardiac devices are validated. Thus, it is expected that the canine heart has very similar electrical model to that found in humans. In 1999, the absence of Heart Rate Turbulence (HRT) after a single Pre-Ventricular Contraction (PVC) was linked to high-risk patient after acute myocardial infarction. Studies of HRT were performed on high-risk patients with Holter-Monitors as were most subsequent HRT studies. If HRT could potentially be used as a risk factor of heart disease, it is interesting to study whether HRT is present following a …

Preparation And Characterization Of Electrospun Poly(D, L-Lactide-Co-Glycolide) Scaffolds For Vascular Tissue Engineering And The Advancement Of An In Vitro Blood Vessel Mimic, Tiffany Richelle Pena

Master's Theses

PREPARATION AND CHARACTERIZATION OF ELECTROSPUN POLY(D,L-LACTIDE-CO-GLYCOLIDE) SCAFFFOLDS FOR VASCULAR TISSUE ENGINEERING AND THE ADVANCEMENT OF AN IN VITRO BLOOD VESSEL MIMIC

Tiffany Richelle Peña

Currently, an estimated 1 in every 3 adult Americans are affected by one or more cardiovascular complications. The most common complication is coronary artery disease, specifically atherosclerosis. Outcomes of balloon angioplasty treatments have been significantly improved with the addition of drug eluting stents to the process. Although both bare metal and drug eluting stents have greatly increased the effectiveness of angioplasty and decreased the occurrence of restenosis, several complications still exist. For this reason, the stent …

Mechanical Simulation Of Articular Cartilage Based On Experimental Results, Kevin Matthew Stewart

Master's Theses

Recently, a constituent based cartilage growth finite element model (CGFEM) was developed in order to predict articular cartilage (AC) biomechanical properties before and after growth. Previous research has noted limitations in the CGFEM such as model convergence with growth periods greater than 12 days. The main aims of this work were to address these limitations through (1) implementation of an exact material Jacobian matrix definition using the Jaumann-Kirchhoff (J-K) method and (2) quantification of elastic material parameters based upon research findings of the Cal Poly Cartilage Biomechanics Group (CPGBG). The J-K method was successfully implemented into the CGFEM and exceeded …

The Impact Of Lipid Percentage On Fibrous Cap Stability In Atherosclerotic Lesions, Anita Lorraine Crompton

Master's Theses

Coronary artery disease (CAD) is a common cause of sudden cardiac death. Much of the disease is not completely understood, which makes treatment and prevention difficult. Many researchers are using technology, such as advanced imaging techniques and finite element analysis, to better understand the disease. While there is much progress being made to look at the analysis of actual excised diseased arteries, there is still not a standardized model to predict the future of any one lesion. The purpose of this study is to explore the possibility of creating a standardized model to predict the mechanical stability of the fibrous …

Preparation For Nerve Membrane Potential Readings Of A Leech, Laboratory Setup And Dissection Process, Jason Patrick Caulfield

Master's Theses

A well documented laboratory setup, leech preparation process, and bio-potential data recording process are needed. Repeatability and quality data recordings are essential and thus dictate the requirements of the laboratory setup and processes listed above. Advances in technology have both helped and hindered this development. While very precise equipment is required to record the low voltage bio-potentials, noisy electronic equipment and wires surrounding the work area provide high levels of interference. Proper laboratory setup and data recording processes, however, limit the unwanted interference. Quality data can only be recorded from a properly handled and prepared leech subject. Proper setup and …

Time-Frequency Analysis Of Intracardiac Electrogram, Erik Brockman

Master's Theses

The Cardiac Rhythm Management Division of St. Jude Medical specializes in the development of implantable cardioverter defibrillators that improve the quality of life for patients diagnosed with a variety of cardiac arrhythmias, especially for patients prone to sudden cardiac death. With the goal to improve detection of cardiac arrhythmias, this study explored the value in time-frequency analysis of intracardiac electrogram in four steps. The first two steps characterized, in the frequency domain, the waveforms that construct the cardiac cycle. The third step developed a new algorithm that putatively provides the least computationally expensive way to identifying cardiac waveforms in the …

Implementation Of Physiologic Flow Conditions In A Blood Vessel Mimic Bioreactor System For The Evaluation Of Intravascular Devices, Marc Cody Dawson

Master's Theses

The prevalence and devastating nature of cardiovascular diseases has led to many advancements in the therapies used to treat the millions of patients that suffer as a result of these conditions. As coronary artery disease (CAD) is the most common of these cardiovascular conditions, it is a major focus of research among the medical industry. Although lifestyle changes and drug therapies can treat early CAD, more advanced cases often require more definitive interventions. In conjunction with angioplasty, stenting of an occluded vessel has shown significant success in preventing restenosis. However, as with nearly every therapeutic process in the medical field, …

Development Of An In-Vitro Tissue Engineered Blood Vessel Mimic Using Human Large Vessel Cell Sources, Dimitri E. Delagrammaticas

Master's Theses

Tissue engineering is an emerging field that offers novel and unmatched potential medical therapies and treatments. While the vast aim of tissue engineering endeavors is to provide clinically implantable constructs, secondary applications have been developed to utilize tissue-engineered constructs for in-vitro evaluation of devices and therapies. Specifically, in-vitro blood vessel mimics (BVM) have been developed to create a bench-top blood vessel model using human cells that can be used to test and evaluate vascular disease treatments and intravascular devices. Previous BVM work has used fat derived human microvascular endothelial cells (EC) sodded on an ePTFE scaffold. To create a more …

Nano-Mechanics Of Cartilage Glycosaminoglycans Using Molecular Dynamics Methods, Kevin Neil Hendrickson

Master's Theses

Articular Cartilage (AC) is the main load carrying material in synovial joints {Hamerman, 1962} and degeneration of AC can cause pain in the form of arthritis. Current work is centered on the method of replacing damaged cartilage inside the body (in vivo) with tissue engineered outside the body (ex vivo) {Temenoff, 2000}. In order to engineer tissue ex vivo similar to the native tissue in structure and function there must be a comprehensive understanding of the mechanical properties of AC. This work focuses on the study of glycosaminoglycans (GAGs), a molecule known to be primarily responsible for the compressive stiffness …

Design And Optimization Of A Blood Vessel Mimic Bioreactor System For The Evaluation Of Intravascular Devices In Simple And Complex Vessel Geometries, Sara M. Leifer

Master's Theses

Coronary artery disease affects millions of people and the ability to detect and treat the disease is advancing at a rapid rate. As a result, the development of intravascular technologies is the focus of many medical device manufacturers. Specifically, coronary stent implantation is being performed in an increasing number of patients and a number of new stent designs have been introduced to the market, resulting in the need for improved preclinical testing methods. An in vitro tissue engineered “blood vessel mimic” (BVM) system has previously been established and its feasibility for the initial testing of newly emerging intravascular technology has …

Development Of A Cell Depositing System Using Inkjet Technology, Jason Robert Ozaeta

Master's Theses

In the past decade, advances in tissue engineering have allowed researchers to fabricate simple tissues. However, the process of creating these native tissues is a time consuming and inefficient process. A scaffold must first be fabricated then exposed to a sea of cells in the hopes of seeding. Furthermore, even though cells may have attached, more time must be spent in order to allow the cells to migrate to their ideal locations. To deal with this problem, researchers have investigated whether rapid prototyping principals could be adapted to facilitate the cell seeding process by placing cells in their respective locations …