Engineering Commons^™

A Linear Combination Of Heuristics Approach To Spatial Sampling Hyperspectral Data For Target Tracking, Barry R. Secrest

Theses and Dissertations

Persistent surveillance of the battlespace results in better battlespace awareness which aids in obtaining air superiority, winning battles, and saving friendly lives. Although hyperspectral imagery (HSI) data has proven useful for discriminating targets, it presents many challenges as a useful tool in persistent surveillance. A new sensor under development has the potential of overcoming these challenges and transforming our persistent surveillance capability by providing HSI data for a limited number of pixels and grayscale video for the remainder. The challenge of exploiting this new sensor is determining where the HSI data in the sensor's field of view will be the …

Effects Of Prior Aging At 274⁰C In Argon On Inelastic Deformation Behavior Of Pmr-15 Polymer At 288⁰C: Experiment And Modeling, Joseph A. Wahlquist

Theses and Dissertations

No abstract provided.

Nickel-Based Catalysts For Gasification Of Glucose In Supercritical Water, Muhammad Badrul Islam Chowdhury

Electronic Thesis and Dissertation Repository

Gasification of waste biomass to form hydrogen, H2, is a promising new source of green energy; while providing the additional benefit of treating challenging and hazardous waste streams that pollute the environment. Gasification of biomass in supercritical water (SCW) offers an attractive alternative to avoid the energy intensive drying process. In this approach, biomass is hydrolyzed by water into smaller molecules in the presence of a suitable catalyst. This study was aimed at developing an alumina supported nickel based non-noble metal catalyst suitable for biomass gasification in SCW. A lack of detailed characterization on fresh and spent catalysts in SCW …

Design Of A Near-Constant Force Spring For Orthopedic Implants, Christopher Hartman, Paul Rotarius

Honors Theses

The design and testing of a spring assembly for the attachment of an orthopedic implant is presented. The assembly is intended to supply a constant compressive force of approximately 800 lb. at the bone-implant interface, while exhibiting insensitivity to changes in the displacement of the clamping device. This near-constant force will aid in-growth of bone tissue at the implant surface. This constant compressive force was ultimately not attained due to the packaging dimensions and materials available. However, significant improvement was made upon the current design in use by lowering the spring constant around 800 lb.

The final assembly fits in …

Synthesis And Characterization Of Electrospun Gelatin/Dendrimer Scaffold Encapsulated With A Silver As A Potential Antimicrobial Wound Dressing, Alpana Dongargaonkar

Theses and Dissertations

A novel nanofiber scaffold was fabricated and characterized as a potential antimicrobial wound dressing. Half generation polyamidoamine (PAMAM) dendrimer G3.5 was covalently conjugated to gelatin. Gelatin alone or with gelatin-dendrimer conjugates was electrospun into nanofiber scaffolds. Gelatin is a derivative of natural collagen, and it is biocompatible, non-toxic and inexpensive, making it a desirable component in a wound dressing. Dendrimers are synthetic polymers comprising of a central core, internal branches and reactive surface groups. They provide a structurally controlled architecture for drug release. Silver was incorporated into the scaffold in situ due to its broad spectrum of antimicrobial properties. The …

Identifying Potential Applications For Lamina Emergent Mechanisms And Evaluating Their Suitability For Credit-Card-Sized Products, Nathan Bryce Albrechtsen

Theses and Dissertations

Lamina emergent mechanisms (LEMs) are a maturing technology that is prepared for commercial implementation into new products. LEMs are defined by three functional characteristics; they (1) are compliant, (2) are fabricated from planar materials, and (3) emerge from a flat initial state. Advantages, design challenges, and design tools are described for each of the functional characteristics. Opportunities for LEMs are discussed, namely disposable LEMs, novel arrays of LEMs, scaled LEMs, LEMs with surprising motion, shock absorbing LEMs, and deployable LEMs. Technology push product development processes were employed to select applications for LEMs. LEM technology was characterized. In a LEM workshop, …

Development Of A Flexible Fpga-Based Platform For Flight Control System Research, Robert Demott

Theses and Dissertations

This work is part of ongoing research conducted at Virginia Commonwealth University relating to unmanned aerial vehicles. The primary objective of this thesis was to develop a flexible, high-performance autopilot platform in order to facilitate research on advanced flight control algorithms. A dual FPGA-based system architecture utilizing a stacked, multi-board design was created to meet this goal. Processing tasks were split between the two FPGA devices, allowing for improved system timing and increased throughput. A combination of analog and digital filtering techniques were employed in the new system, resulting in enhanced sensor accuracy and precision compared to the previous generation …

Development Of Electroencephalography Based Brain Controlled Switch And Nerve Conduction Study Simulator Software, Kai Qian

Theses and Dissertations

This thesis investigated the development of an EEG-based brain controlled switch and the design of a software for nerve conduction study. For EEG-based brain controlled switch, we proposed a novel paradigm for an online brain-controlled switch based on Event-Related Synchronizations (ERDs) following external sync signals. Furthermore, the ERD feature was enhanced by 3 event-related moving averages and the performance was tested online. Subjects were instructed to perform an intended motor task following an external sync signal in order to turn on a virtual switch. Meanwhile, the beta-band (16-20Hz) relative ERD power (ERD in reverse value order) of a single EEG …

Automated Tool Design For Complex Free-Form Components, Kevin G. Foster

Theses and Dissertations

In today's competitive manufacturing industries, companies strive to reduce manufacturing development costs and lead times in hopes of reducing costs and capturing more market share from early release of their new or redesigned products. Tooling lead time constraints are some of the more significant challenges facing product development of advanced free-form components. This is especially true for complex designs in which large dies, molds or other large forming tools are required. The lead time for tooling, in general, consists of three main components; material acquisition, tool design and engineering, and tool manufacturing. Lead times for material acquisition and tool manufacture …

Numerical Simulation Of Underground Solar Thermal Energy Storage, Marshall Sweet

Theses and Dissertations

The United States Department of Energy indicates that 97% of all homes in the US use fossil fuels either directly or indirectly for space heating. In 2005, space heating in residential homes was responsible for releasing approximately 502 million metric tons of carbon dioxide into the atmosphere. Meanwhile, the Sun provides the Earth with 1000 watts per square meter of power everyday. This document discusses the research of modeling a system that will capture and store solar energy during the summer for use during the following winter. Specifically, flat plate solar thermal collectors attached to the roof of a single …

Digital Implementation Of A True Random Number Generator, Sam Mitchum

Theses and Dissertations

Random numbers are important for gaming, simulation and cryptography. Random numbers have been generated using analog circuitry. Two problems exist with using analog circuits in a digital design: (1) analog components require an analog circuit designer to insure proper structure and functionality and (2) analog components are not easily transmigrated into a different fabrication technology. This paper proposes a class of random number generators that are constructed using only digital components and typical digital design methodology. The proposed classification is called divergent path since the path of generated numbers through the range of possible values diverges at every sampling. One …

Modelación Física De Sumideros Laterales Tipo Ventana Para Vías Urbanas, Miguel Ángel Barragán Ochica

Ingeniería Civil

El proyecto comprende dos partes principales. La primera de carácter teórico, en la cual se hizo un análisis del estado del arte con respecto al estudio de los sumideros laterales tipo ventana y se realizaron salidas de campo con el fin de recopilar un inventario sobre las características principales de los sumideros estudiados en este proyecto. La segunda parte enmarca el trabajo de laboratorio, en el cual se construyó un modelo a escala de una vía urbana (Ver Imagen 1), y con este modelo se 6 realizaron mediciones del caudal resumido por los sumideros laterales bajo diversas condiciones. Entre las …

The Development Of A Phase Locked Wind Turbine Blade Finite Element Model To Predict Loads And Deflections During Fatigue Testing, Kyle Freeman

Master's Theses - Daytona Beach

Full scale blade testing provides blade manufacturers with quantitative data in order to assess blade design, manufacturing and durability. Structural testing is a requirement in order to design reliable blades, and to develop a further understanding of the dynamics involved in a modern turbine blade. Blade tests can be conducted in either a single axis or dual axis configurations. Historically, fatigue testing has been performed by utilizing forced displacement systems. These systems do not allow for the load phase angle to be controlled, and the maximum load application in the edge and flap directions are allowed to vary. The PhLEX …

The Development Of An Adaptive Control System For A Phase-Locked Excitation (Phlex) Method For Advanced Wind Turbine Blade Fatigue Testing, William Michael Haupfear

Master's Theses - Daytona Beach

The National Renewable Energy Laboratory's (NREL) National Wind Technology Center (NWTC) provides the means necessary for advanced wind turbine blade testing. To improve on the current testing methods, a new testing method is being developed using the existing dual-axis fatigue testing capabilities in conjunction with another actuator to provide a phase-locked excitation method with adaptive algorithms and advanced control system strategies. This testing method will provide a more representative loading of the blade for fatigue testing as compared to loading seen in the field. The control system will integrate the MTS software and controller with a supervisory controller, programmed in …

Pin-Wise Loading Optimization And Lattice–To-Core Coupling For Isotopic Management In Light Water Reactors, Hermilo Hernandez Noyola

Doctoral Dissertations

A generalized software capability has been developed for the pin-wise loading optimization of light water reactor (LWR) fuel lattices with the enhanced flexibility of control variables that characterize heterogeneous or blended target pins loaded with non-standard compositions, such as minor actinides (MAs). Furthermore, this study has developed the software coupling to evaluate the performance of optimized lattices outside their reflective boundary conditions and within the realistic three-dimensional core-wide environment of a LWR.

The illustration of the methodologies and software tools developed helps provide a deeper understanding of the behavior of optimized lattices within a full core environment. The practical applications …

Multivariate Optimization Of Neutron Detectors Through Modeling, Martin Rodney Williamson

Doctoral Dissertations

Due to the eminent shortage of 3He, there exists a significant need to develop a new (or optimize an existing) neutron detection system which would reduce the dependency on the current 3He-based detectors for Domestic Nuclear Detection Office (DNDO) applications. The purpose of this research is to develop a novel methodology for optimizing candidate neutron detector designs using multivariate statistical analysis of Monte Carlo radiation transport code (MCNPX) models. The developed methodology allows the simultaneous optimization of multiple detector parameters with respect to multiple response parameters which measure the overall performance of a candidate neutron detector. This is achieved by …

Environmental Impacts To Stream Acidification And Brook Trout Populations In The Great Smoky Mountains National Park, Keil Jason Neff

Doctoral Dissertations

This research supports development of aquatic resource management strategies to address acid deposition in the Great Smoky Mountain National Park (GRSM) by 1) developing relationships between baseflow and stormflow chemical constituents and examining effects of elevation, area, geology, soil, and vegetation on stream chemistry; 2) evaluating physiological condition in brook trout in relation to changes in stream chemistry during stream acidification episodes, and 3) evaluating brook trout metrics with respect to stream chemistry, basin characteristics, and ecologically relevant hydrologic parameters. (1) Stream chemistry was monitored in eight GRSM streams considering basin area, site elevation, Anakeesta geology, soil, and vegetation. Following …

Durability And Fatigue Behavior Of Cip Concrete Connections For Accelerated Bridge Construction, Peng Zhu

Doctoral Dissertations

Continuous longitudinal and transverse U-bar joint connections between flanges of the decked bulb-Ts (DBTs) or between precast panels for accelerated bridge construction are investigated. The procedure for selecting durable closure pour (CP) materials for the connections is discussed firstly. The accelerated construction is quantified as two categories: overnight cure and 7-day cure of CP materials. Candidate materials are selected first based on literature review as well as tests of compressive strength and flow and workability. Then, performance criteria for selecting durable CP materials for both categories are developed based on durability tests of selected candidate materials. These durability tests include …

Adaptive Voltage Control Methods Using Distributed Energy Resources, Huijuan Li

Doctoral Dissertations

Distributed energy resources (DE) with power electronics interfaces and logic control using local measurements are capable of providing reactive power related to ancillary system services. In particular, local voltage regulation has drawn much attention in regards to power system reliability and voltage stability, especially from past major cascading outages. This dissertation addresses the challenges of controlling the DEs to regulate the local voltage in distribution systems.

First, an adaptive voltage control method has been proposed to dynamically modify the control parameters of a single DE to respond to system changes such that the ideal response can be achieved. Theoretical analysis …

Characterization And Fabrication Of Active Matrix Thin Film Transistors For An Addressable Microfluidic Electrowetting Channel Device, Seyeoul Kwon

Doctoral Dissertations

The characterization and fabrication of active matrix thin film transistors (TFTs) has been studied for an addressable microfluidic electrowetting channel device as application. A new transparent semiconductor material, Amorphous Indium Gallium Zinc Oxide (a-IGZO), is used for TFT, which shows high electrical performance rather than amorphous silicon based TFT; higher mobility and even higher transparency. The purpose of this dissertation is to optimize each TFT process including the optimization of a-IGZO properties to achieve robust device for application. To minimize hysteresis of TFT curves, the gate dielectric is discussed extensively in this dissertation. By optimizing gas ratio of NH3SiH4, it …

Dependence Of Microstructure Evolution, Texture, And Mechanical Behavior Of A Mg Alloy On Thermo-Mechanical Input During Friction Stir Processing, Zhenzhen Yu

Doctoral Dissertations

In this thesis, the relationship among friction stir processing (FSP) parameters, microstructure evolution, texture development, and mechanical hehavior of AZ31B Mg alloy was investigated.

First of all, in order to reveal the correlation among the deformation conditions, dynamic recrystallization (DRX) mechanisms, and microstructure evolution in the Mg alloy, hot compression tests at a wide range of Zener-Hollomon parameter (Z) values were conducted. Through optical microscopic examination, it was found out that above a critical Z value, twinning influences the DRX process resulting in a more effective grain refinement, which is manifested in a significant change in the slope of the …

Thin Film Combinatorial Synthesis Of Advanced Scintillation Materials, Jonathan Daniel Peak

Doctoral Dissertations

The development and application of a combinatorial sputtering thin film technique to screen potential scintillation material systems was investigated. The technique was first benchmarked by exploring the binary lutetium oxide-silicon oxide material system, which successfully identified the luminescence phases of the system, Lu2SiO5 (LSO) and Lu2Si2O7 (LPS). The second application was to optimize the activator concentration in cerium doped LSO. The successfully optimized cerium concentration in the thin film LSO of 0.34 atomic percent was much greater than the standard cerium concentration in single crystal LSO. This lead to an intensive study based on temperature dependent steady-state and lifetime photoluminescence …

Energetics And Kinetics Of Dislocation Initiation In The Stressed Volume At Small Scales, Tianlei Li

Doctoral Dissertations

Instrumented nanoindentation techniques have been widely used in characterizing mechanical behavior of materials in small length scales. For defect-free single crystals under nanoindentation, the onset of elastic-plastic transition is often shown by a sudden displacement burst in the measured load-displacement curve. It is believed to result from the homogeneous dislocation nucleation because the maximum shear stress at the pop-in load approaches the theoretical strength of the material and because statistical measurements agree with a thermally activated process of homogeneous dislocation nucleation. For single crystals with defects, the pop-in is believed to result from the sudden motion of pre-existing dislocations or …

Utilization Of Automated Gcc Optimization For Dual-Width Instruction Sets On The Arm Architecture, Shane Watson

Computer Engineering

One of the most important considerations in embedded systems is code size. This consideration is obviously imposed by external factors such as cost and physical space, but what it boils down to is that we want our devices to be as powerful as they can within a (typically limited) specific form factor. This limits the amount of space we have for memory and as such we should always be considering the code size of our application and making sure it’s as efficient as possible. We also then need to consider other factors such as performance and power consumption. This is …

Development Of A Cubesat Payload To Model Particle Dampening In Space: Design And Implementation Of Software For Cp7, Daniel Walker

Computer Engineering

The California Polytechnic State University CubeSat student research & development group, PolySat, is currently in a mature development stage of a single unit CubeSat designated CP7. The CP7 mission implements a scientific payload designed to characterize particle dampers in microgravity conditions. When subjected to vibration, the momentum exchanges and frictional forces of the particles create a damping effect that can be optimized to suit a number of applications over a broad frequency and amplitude range. In space based applications, particle dampers would serve as a robust and simple device to eliminate jitter in optical assemblies and other sensitive instrumentation. This …

The Next Generation Cubesat: A Modular And Adaptable Cubesat Frame Design, James Dolengewicz, Lucas Whipple, Stephanie Wong

Mechanical Engineering

The goal of this project is to develop an improved next-generation CubeSat structure for Cal Poly’s PolySat program. Notable achievements include significantly increased ease of access, design to optimize payload space, improved machinability, increased modularity and a platform which allows for easy integration of future payloads.

Piedras Blancas Clock Works, Andrew James, Andrew Jupin, Matt Weber

Mechanical Engineering

In 1875, the Piedras Blancas Lighthouse was built to warn ships sailing the California coast of the hazards of the rocky shore. In 1949 a fierce storm damaged the top portion of the lighthouse and the eight ton cast iron and brass assembly had to be replaced by a much lighter piece that still served the purpose of warning oncoming vessels. The former top portion came to rest in downtown Cambria and is still there today, enclosed in a glass room to be observed by visitors and townspeople. Today, the Piedras Blancas Light station is cared for by the Bureau …

Adapted Recumbent Bike, Kurtis Mundell, Dane Tiemeier, Laura Yakuma, Darius Yu

Mechanical Engineering

The adapted recumbent project was to redesign a disabled veteran’s recumbent bicycle. The main areas of concern were the crank pedal, chain tension, braking and steering system, and ergonomics. Since the customer is an avid biker, this bike will be used often, so the design is based on the ease of repair and replacement. The crank system was redesigned to a lightweight, adjustable part with chain clearance and high strength. The chain tension was improved by replacing the existing single idler wheel/chain tube system with a dual idler wheel system. The dual idler has a titanium sprocket in one of …

Expansion In Existing And Future Franchises, Shane Hart, Daniel Jeng

Industrial and Manufacturing Engineering

Zensho Group has recently acquired the restaurant US based chains CoCo’s and Carrows but has not been able to affirm the same growth as the company has established in its home country of Japan. In order to fulfill their need to grow, extensive market analysis and research needs to be done. An expansion eastward and the introduction of their flagship restaurant chain, Sukiya, would offer growth potential. Determining the best locations for these new stores is the goal of this project. Low cost and high market penetration potential will be used to recommend the ideal locations that will benefit the …

Sustainable Climate Control For Mid-Rise Office Building In The Salt Lake Valley, Philip M. Coleman

Industrial and Manufacturing Engineering

This report examines the sustainability of Trane’s EarthWiseTM climate control systems in the Salt Lake Valley (and the United States Mountain West in general). A simulation is performed to determine the best climate control system for a LEED Silver, 5-story tenant office building. This new building is a duplication of a pre-existing building. The climate control system installed at the preexisting building is used as a baseline against which three (3) alternative systems are compared. The social, ecological, and economic impact of each alternative is examined to determine which is the most sustainable. Since the baseline system is a proven …