Engineering Commons^™

Quasi-Static And Impact Load Response Of Bfrp-Reinforced Concrete Beams And Post-Terrorist-Attack Sub-Assemblages, José Luis Carrasquillo

Civil & Environmental Engineering Theses & Dissertations

This dissertation presents the outcome of a theoretical and experimental study of Basalt Fiber Reinforced Polymer (BFRP) reinforced concrete beams and post-terrorist-attack subassemblages subjected to either quasi-static or impact load. Both BFRP reinforcement as well as BFRP fabric are used in this investigation. The sub-assemblage consists of an otherwise two-span beam converted to a fixed-end single-span one owing to the loss of a middle column blasted off during the terrorist attack. The simply supported beams are subjected to a midspan quasistatic or an impact load. However, each sub-assemblage is subjected to a quasi-static load up to collapse to simulate the …

Thermo-Elasto-Plastic Stability Of Biaxially Loaded Hollow Rectangular Section Steel Beam-Columns With Applied Torsion, George Adomako Kumi

Civil & Environmental Engineering Theses & Dissertations

Presented herein is an experimental and theoretical study of biaxially loaded hollow rectangular section steel beam-columns with applied torsion at elevated temperatures. The theoretical analysis is based on a system of simultaneous materially nonlinear differential equations of equilibrium for which an iterative semi-analytic solution approach is formulated. Although the primary goal of this research is to study the influence of elevated temperatures on the steel member with the complex loading, rigorous analysis is also conducted of the member at ambient temperature for comparison. The experimental part of the study involves conducting tests on the members at both ambient and high …

Cfd Study On Two-Phase Flow Patterns In A Pipe With 90º Elbow In Different Operating Conditions, Hagar Alm-Eldin Bastawissi, Mohammed Ahmed Khafagy, E. A. El Shenawy Prof. Dr., Ahmed M. Salem Dr

Journal of Engineering Research

Recently, CFD has offered a technological solution for modelling multi-phase flow in which we can make endless simulations with reduced expenses and effort in high accuracy results; we shall also mention that experimental studies have limitations for safety considerations when experimenting with flow in high temperature or pressure values or medium nature as in nuclear or chemical flows.In this paper, we used the ANSYS FLUENT CFD program to simulate the two-phase flow in a pipe to study the effect of attaching a 90-degree elbow fitting to the piping system, seeking to find out the change in the pattern and resulting …

Recent Advances In Solar Photo(Electro)Catalytic Nitrogen Fixation, Jun-Bo Ma, Sheng Lin, Zhiqun Lin, Lan Sun, Chang-Jian Lin

Journal of Electrochemistry

Ammonia (NH₃) is an essential chemical in modern society. It is currently produced in industry by the Haber-Bosch process using H₂ and N₂ as reactants in the presence of iron-based catalysts at high-temperature (400–600 ^oC) and extremely highpressure (20–40 MPa) conditions. However, its efficiency is limited to 10% to 15%. At the same time, a large amount of energy is consumed, and CO₂ emission is inevitably. The development of a sustainable, clean, and environmentally friendly energy system represents a key strategy to address energy crisis and environmental pollution, ultimately aiming to achieve carbon neutrality. …

Understanding Effective Elastic Properties And Stress-Strain Evolution In Composite Granular Rocks Using Discrete Element Modeling, Prasad Pothana, Fernando E. Garcia, Kegang Ling

Petroleum Engineering Posters and Presentations

The mechanical behavior of composite granular rocks is a multifaceted phenomenon relevant to various geoengineering applications. Traditional homogenization models and continuum mechanics-based numerical methods often fall short of accurately capturing the intricacies of granular materials. Granular materials exhibit heterogeneity and arching mechanisms governing the force networks that ensure system stability. Unlike continuum-based approaches, particulate discrete element methods have an advantage in assessing effective material properties by considering material heterogeneity and grain-level physical interactions. This study evaluates effective elastic properties using particle flow code using flat-joint contact law for composite binary mixtures with a stiff inclusion embedded within a matrix material. …

Investigation Of Gas Dynamics In Water And Oil-Based Muds Using Das, Dts, And Dss Measurements, Temitayo S. Adeyemi

LSU Master's Theses

Reliable prediction of gas migration velocity, void fraction, and length of gas-affected region in water and oil-based muds is essential for effective planning, control, and optimization of drilling operations. However, there is a gap in our understanding of gas behavior and dynamics in water and oil-based muds. This is a consequence of the use of experimental systems that are not representative of field-scale conditions. This study seeks to bridge the gap via the well-scale deployment of distributed fiber-optic sensors for real-time monitoring of gas behavior and dynamics in water and oil-based mud. The aforementioned parameters were estimated in real-time using …

Harnessing Nanocellulose For Sustainable Carbon Capture: Synthesis, Processing, And Performance Evaluation, Jerred C. Wassgren

Doctoral Dissertations

Scientists and governments have recognized the need for environmental remediation, most notably with the adoption of the Paris Agreement in 2016. One of the major concerns is the production of greenhouse gases (GHGs). The major GHG is carbon dioxide (CO₂) in which humans emit over 36 gigatons yearly. Atmospheric CO₂ is responsible for 60% of the heat retained by the earth – resulting in rising temperatures, melting ice caps, and increasing ocean acidification. Therefore, a major goal of the Paris Agreement was to reduce GHG emissions as well as the capture of CO₂ from the atmosphere. …

Runway 1-19: Greensburg Municipal Airport’S New 5,405-Ft Runway:, John Feister, Jeremy Books

Purdue Road School

The Greensburg Municipal Airport completed the construction of Runway 1-19 on a new alignment in 2022. Runway 1-19 is 5,405-ft long × 100-ft wide and replaced the existing Runway 18-36 that was 3,430-ft long × 40-ft wide. This was a multi-year construction project with a broad scope that included land acquisition; construction in a flood-way; grading and drainage; paving and electrical; and extensive FAA coordination. Challenges and successes will be discussed.

Highly Efficient Dopamine Sensing With A Carbon Nanotube-Encapsulated Metal Chalcogenide Nanostructure, Harish Singh, Jiandong Wu, Kurt A.L. Lagemann, Manashi Nath

Chemical and Biochemical Engineering Faculty Research & Creative Works

Carbon nanotube-encapsulated nickel selenide composite nanostructures were used as nonenzymatic electrochemical sensors for dopamine detection. These composite nanostructures were synthesized through a simple, one-step, and environmentally friendly chemical vapor deposition method, wherein the CNTs were formed in situ from pyrolysis of a carbon-rich metallo-organic precursor. The composition and morphology of these hybrid NiSe2-filled carbon nanostructures were confirmed by powder X-ray diffraction, Raman, X-ray photoelectron spectroscopy, and high-resolution transmission electron microscopy images. Electrochemical tests demonstrated that the as-synthesized hybrid nanostructures exhibited outstanding electrocatalytic performance toward dopamine oxidation, with a high sensitivity of 19.62 μA μM-1 cm-2, low detection limit, broad linear …

Challenges And Opportunities In Electrification Of Adsorptive Separation Processes, Abdullah Al Moinee, Ali A. Rownaghi, Fateme Rezaei

Chemical and Biochemical Engineering Faculty Research & Creative Works

A global energy transition from fossil-based to renewable-based systems requires advancements in various energy sectors. Current chemical separation processes are quite energy-intensive and require significant advancement to make this transition happen. In the energy transition era, reducing the dependency of separation processes on fossil-based thermal energy seems inevitable for transitioning smoothly and meeting the stringent timelines. In particular, adsorption-based separation processes have the potential to be fully electrified through innovative strategies in developing stimuli-responsive adsorbents and swing processes. In this review, we discuss the recent efforts in electrification of adsorption processes and provide an overview of emerging materials and processes. …

Adsorption Of Crystal Violet Dye From Synthetic Wastewater By Ball-Milled Royal Palm Leaf Sheath, Neloy Sen, Nawrin Rahman Shefa, Kismot Reza, Sk Md Ali Zaker Shawon, Md. Wasikur Rahman

Physics and Astronomy Faculty Publications and Presentations

The current study shows that using a batch approach to remove crystal violet dye from synthetic wastewater is feasible when using royal palm leaf sheath powder as an adsorbent. In order to investigate the effects of many parameters, including starting concentration, pH effect, dye concentration, adsorbent dose, contact time, and temperature, experiments were carried out under various operating conditions. Maximum removal was obtained at pH 6 and at a concentration of 100 ppm, which are considered as ideal values. The influence of pH and dye concentration was shown to be substantial. Langmuir, Freundlich, and Temkin isotherm models were fitted to …

Utilization Of Caputo Fractional Derivative In Mhd Nanofluid Flow With Soret And Thermal Radiation Effects, Harshad Patel, Gopal Nanda

Applications and Applied Mathematics: An International Journal (AAM)

In existence of heat diffusion and thermal radiation, an analytical equation is found for unsteady MHD flow past an exponentially accelerating vertical plate in optically thick water based nanofluid. The governing equations are made dimensionless by similarity transformation. A definition of Caputo fractional derivative is applied to generalize governing system of partial differential equations. Laplace transform techniques are applied and obtained the analytical solutions of proposed problems. For a physical point of view, numerical results are obtained using MATLAB software and presented via graphs. From the results, it is concluded that magnetic fields tend to reduce velocity. It is also …

Inverting Geodetic Strain Rates For Slip Deficit Rate In Complex Deforming Zones: An Application To The New Zealand Plate Boundary, Kaj M. Johnson, Laura M. Wallace, Jeremy Maurer, Ian Hamling, Charles Williams, Chris Rollins, Matt Gerstenberger, Russ Van Dissen

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

The potential for future earthquakes on faults is often inferred from inversions of geodetically derived surface velocities for locking on faults using kinematic models such as block models. This can be challenging in complex deforming zones with many closely spaced faults or where deformation is not readily described with block motions. Furthermore, surface strain rates are more directly related to coupling on faults than surface velocities. We present a methodology for estimating slip deficit rate directly from strain rate and apply it to New Zealand for the purpose of incorporating geodetic data in the 2022 revision of the New Zealand …

Layered Mantle Flow Field Associated With Plate Kinematics And Slab Modulation Underneath The Horseshoe-Shaped Banda Arc-Islands, Sijia Li, Fansheng Kong, Kelly H. Liu, Stephen S. Gao

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

The Banda Arc-Continent Collision Zone Signifies One Of The Most Seismically Active And Tectonically Intricate Zones. The High Convergence Rate Across The Region, Coupled With The Exceptionally Arcuate Arc And Subducted Slab, Makes It An Ideal Locale For Investigating Interactions Between Plate (Slab) Kinematics And Plastic Flow In The Asthenosphere, Which Can Be Diagnosed By Seismic Anisotropy From Shear Wave Splitting Analyses. In Total, 206 Pairs Of Splitting Measurements Using Teleseismic SKS, SKKS, And PKS, Along With 43 Pairs Using Local S Phases, Are Obtained By Utilizing Broadband Seismic Data From Five Permanent Seismic Stations. To Reduce The Ambiguity In …

Thermal, Electrical, And Spin Transport: Encompassing Low-Damping Ferromagnets And Antiferromagnetic/Ferromagnetic Heterostructures, Matthew Ryan Natale

Electronic Theses and Dissertations

Continuing technological advancements bring forth escalating challenges in global energy consumption and subsequent power dissipation, posing significant economic and environmental concerns. In response to these difficulties, the fields of thermoelectrics, spintronics, and spincaloritronics emerge as contemporary solutions, each presenting unique advantages. Thermoelectric devices, based on the Seebeck effect, other a passive, carbon-free energy generating solution from waste heat. Although current thermoelectric technology encounters hurdles in achieving optimal efficiencies without intricate designs or complex materials engineering, recently research into low-damping metallic ferromagnetic thin films have provided a new method to enhance spin wave lifetimes, thus contributing to thermoelectric voltage improvements. As …

Laboratory Evaluation Of High-Temperature Resistant Lysine-Based Polymer Gel Systems For Leakage Control, Tao Song, Xuyang Tian, Baojun Bai, Yugandhara Eriyagama, Mohamed Ahdaya, Adel Alotibi, Thomas P. Schuman

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

In-situ crosslinking gel known for its cost-effectiveness, has been employed for decades to plug high-permeability features in subsurface environments. However, some commonly used crosslinkers are being phased out due to the increasingly rigorous environmental regulations. As a newly discovered environmentally friendly crosslinker, lysine can crosslink the partially hydrolyzed polyacrylamide through transamidation reaction. The present work aimed to study the effect of polymer composition and concentration on the gelation behavior of lysine and high molecular weight acrylamide-based polymers. Several commercial high molecular weight polymers with different contents of 2-Acrylamido-2-methyl-1-propane sulfonic acid (AMPS) including AN-105/125, SAV-55/37/28, and SAV-10 were deployed in this …

Pd-Modified Cuo-Zno-Al2o3 Catalysts Via Mixed-Phases-Containing Precursor For Methanol Synthesis From Co2 Hydrogenation Under Mild Conditions, Xiao Fan, Kaiying Wang, Xiaoqing He, Shiguang Li, Miao Yu, Xinhua Liang

Chemical and Biochemical Engineering Faculty Research & Creative Works

A series of palladium-modified (Pd-modified) CuO-ZnO-Al2O3 (CZA) catalysts with various Pd loadings (0.3 wt% to 2.4 wt%) were prepared using the wetness impregnation method, on two CZA supports with different structures that are CZA-aged precursor composed of a mixture of zincian-malachite and hydrotalcite-like phases (CZA-zH), and CuO-ZnO-Al2O3 metal oxide nanoparticles (CZA-MO). Enhancement on catalytic activity can be observed on both Pd-modified CZA catalysts in a temperature range of 180–240 °C for methanol synthesis via CO2 hydrogenation. Pd/CZA-zH catalysts exhibited a more efficient and stable production of methanol at a relatively low reaction temperature of 180 °C for 100 hrs. of …

Advancement In Heavy Oil Upgrading And Sustainable Exploration Emerging Technologies, Youssef Yatimi, Jihane Mendil, Meena Marafi, Ahmed Alalou, Muthanna H. Al-Dahhan

Chemical and Biochemical Engineering Faculty Research & Creative Works

Upgrading heavy oil is a subject of high importance for fossil fuel industry due to the rapid depletion of light oil reservoirs and the consequent increased demand for upgrading heavy oil. In this review, the advancement made in heavy oil upgrading and the proposed sustainable emerging technologies dedicated to heavy oil processing have been discussed in a comprehensive and informative manner with consideration to the encountered associated with properties of heavy oil including its significant content of undesirable large molecular weight hydrocarbons, its high viscosity, and its elevated impurity level. The shortcomings of conventional crude oil upgrading technologies are outlined, …

Strategy For Predictive Control Of The Rectification Process Based On A Model Controller With A Given Forecast, Ildar Rafkatovich Sultanov

Chemical Technology, Control and Management

A method is being developed to optimize the generated controls for the multicomponent distillation process with prediction, based on predictive data with a moving horizon. The difference between this method and the classical modeling approach, in which the percentage of the degree of opening of valves installed on the output streams of the column is used as control actions, is that control occurs on the feedback principle. The proposed method is based on the use of a dynamic process model to optimize control actions in real time in order to achieve certain production targets. The essence of the MPC approach …

Identification Of Faults In Highways Using Approximation Methods And Algorithms, Khudayberdiyev Khakkulmirzayevich Mirzaakbar, Anvar Asatilloyevich Ravshanov

Chemical Technology, Control and Management

Many fast Fourier transforms are used to identify defective parts of uneven surfaces on roads and send information to relevant organizations on the road, using the " RAVON YO‘LLAR" application installed on a mobile device during car movement. We determine the uneven parts of the road. Smooth and well-maintained roads reduce the risk of vehicle collisions, skidding and other road-related incidents. Timely measures contribute to overall safety, comfort and economic efficiency.

A Neural Network Model For Monitoring And Forecasting The Process Of Storing Oilseeds, N.A. Kabulov

Chemical Technology, Control and Management

The paper presents the results of research on the control, forecasting and management of the storage process of oilseeds. Vegetable oil production and energy consumption are two important factors of oilseed storage systems. The first ones should meet the needs of the population quantitatively and qualitatively. As a result, in order to properly control these two important aspects, it is necessary to maintain an appropriate microclimatic environment using a computational decision support system (DSS) that is able to adapt to changes in environmental characteristics. The multilayer perceptron neural network (MLP-NN) was developed to simulate the temperature and relative humidity profiles …

Synthesize A Neural Network Parameter Optimizer For An Adaptive Pid Controller, Nashvandova Gulruxsor Murot Qizi

Chemical Technology, Control and Management

Wide application of proportional-integral-differential (PID)-regulator in industry requires constant improvement of methods of its parameters superstructuring. In the paper, the questions of optimization of PID-regulator parameters with application of methods of neural network technology are considered. A methodology for selecting the architecture of neural network optimizer designed to determine the tuned parameters of PID regulator is proposed. The algorithm of training of the neural network, with the set on the basis of the method of inverse gradient propagation is offered. The proposed improved PID-neural regulator allowed to provide stabilization of neural network operation and its trainability in the control loop …

Development Of A Criterion Assessing The Level Of Relationship Of Multiple Identified Characteristics For Classification, Mirzoyan Mirzaaxmedovich Kamilov, Oybek Zokirovich Koraboshev, Bobomurod Mamitjonovich Tojiboev

Chemical Technology, Control and Management

This article discusses an optimized version of the standard design developed by Yu.I.Zhuravlev, an optimization procedure through an algebraic approach based on precedent algorithms that solves the problem of pattern identification. The formation of the convex hull of the recognition operator and corrective procedures of information models by mutual compensation of each other was also studied. In addition, the functional connection of recognition operators and the definition of idempotent connection of operators are analyzed.

Analytical-Critical Review Of Widely Used Industrial Devices For Drying Mineral Fertilizers, Djalolitdin Paxritdinovich Mukhitdinov, Aleksey Viktorovich Schulz

Chemical Technology, Control and Management

The article is devoted to the review of the modern state of research in the mineral fertilizers drying field, critical analysis and comparison of widely used drying apparatuses. There are procedures of preliminary equipment selection for soluble fertilizers industrial drying on the basis of such criteria as productivity, efficiency, energy saving, environmental impact degree, indicating the possible advantages and disadvantages of different application variants.

Calculation Of Hydraulic Resistance Of A Tubular-Gridse Nozzle With Spiral Turbulizers, Nurmukhamedov Habibulla Sagdullaevich, Mavlonov Elbek Tulkinovich, S.Kh. Nishonova, Kh.S. Nurmukhamedov

Chemical Technology, Control and Management

The article presents the results of an experimental study on the hydraulic resistance of a tubular-grid nozzle made of smooth pipes and pipes with spiral turbulators. Experiments were carried out with nozzles made of smooth pipes and pipes with turbulators. Spiral turbulators are placed discretely with a step t/d=0,3125-0,9375 and installed on a tube sheet in a checkerboard pattern with a step s/d=1,15-10. Experimental studies were carried out with air flow in the transition region.

It has been established that with increasing numerical values of the dimensionless parameter s/d, the resistance of the pipe package decreases from 1,3 to 1,8 …

Chromatographic Analysis Of The Chemical Composition Of Pyrolysis Distillate, Sh.T. Juraev, B.F. Muxiddinov, U.T. Tailakov

Chemical Technology, Control and Management

The paper presents the results of a study of the physico-chemical characteristics of the liquid fraction of products of thermal oxidative pyrolysis of worn tires. The mass fraction of the volatile gas compounds, the optimal boiling points of the obtained condensates and the flashpoint of pyrolysis liquids, together with the mass composition of cracking products of rubber products at high-temperature pyrolysis at a temperature of 800-900 °C, were determined. Chromatographic analysis allowed us to determine the composition, mainly the mass composition of pyrolysis products, which consisted of carbon (42.8%), higher aliphatic and aromatic hydrocarbons (17.0%), methane (10.2%), benzene (4.2%) and …

Development Of A Mathematical Model Of Magnetic Field Distribution In Magnetic Conductors Of A Wide-Range Current Transformer, Abdurauf Safarov

Chemical Technology, Control and Management

The article is devoted to the analysis of the distribution of the magnetic field in the magnetic conductors of a wide-range current transformer for the development of a mathematical model that can be used as the basis for calculating its static characteristics and error. The design, replacement circuits and design model of a current transformer are given. The relations of magnetic induction and tension from the coordinate of the position of the primary winding are obtained. It is shown that the conversion range can be adjusted depending on the different positions of the bus with current, as a result of …

Artificial Neural Network Modeling Applied For Predicting Reformate Yield And Research Octane Number In The Reforming Process, Badiea S. Babaqi, Abdelrigeeb Ali Al-Gathe, Mohd S. Takriff, Hassimi Abu Hasan, Mohammed H. Al-Douh

Hadhramout University Journal of Natural & Applied Sciences

The prediction model of the continuous catalytic regeneration reforming process was developed for expecting the reformate yield and research octane number using an Artificial Neural Network technique (ANN) to improve the process performance. The proposed model includes temperatures, pressures, and hydrogen to hydrocarbon molar ratio as input parameters while the output of the process represents reformate yield and research octane number. The ANN model was carried out to estimate the process behavior based on the Levenberg-Marquardt Algorithm, which included the nine input parameters, two hidden layers (10-5 neurons), and two parameters as network outputs. The results obtained were that the …

Steminism: Analyzing Factors That Improve Retention Of Women In Stem, Kira Carter, Jane Kelley, Jason Vasser-Elong, Rc Patterson

Dissertations

Our co-authored research ‘Steminism: Analyzing Factors That Improve Retention for Women as STEM Majors’ analyzed factors that contributed to the retention of women in science, technology, engineering, and mathematics (STEM) programs at Missouri University of Science & Technology (Missouri S&T). Women make up half of the US population, and while careers in (STEM) are an integral part of the US economy, women are underrepresented in these career fields. The purpose of our dissertation is to address the underrepresentation of women in STEM majors. Our methodology included homogeneous sampling to collect qualitative data. More specifically, we consulted with academic advisors and …

Development Of Inorganically Cross-Linked Sulfonated Polyacrylamide Preformed Particle Gels For Conformance Control: Impact Of Anionic Groups, Reem Elaf, Ahmed Hamza, Hassan Nimir, Mohammed Saad, Ibnelwaleed A. Hussein, Baojun Bai

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

Modern oil and gas extraction faces challenges, notably from the surplus of produced water, hampering hydrocarbon recovery and raising environmental and economic concerns. A promising solution is the injection of preformed particle gels (PPGs) into the reservoir's fractures and high permeability zones, facilitating production processes. This study introduces a novel class of inorganically cross-linked PPGs with exceptionally high swelling capacities, comprising sulfonated polyacrylamide cross-linked with aluminum attached to acetate, nitrate, sulfate, and lactate anions individually. These PPGs function as superabsorbents, capable of absorbing water at a ratio of 100-700 times their dry weight while maintaining adequate gel strength up to …