Optics Commons^™

Examination Of The Nonlinear Dynamics Of A Chaotic Acousto-Optic Bragg Modulator With Feedback Under Signal Encryption And Decryption, Mohammed A. Al-Saedi, Monish Ranjan Chatterjee

Electrical and Computer Engineering Faculty Publications

An acousto-optic Bragg cell with first-order feedback, which exhibits chaotic behavior past the threshold for bistability, was recently examined for possible chaotic encryption and recovery of simple messages (such as low-amplitude periodic signals) applied via the bias input of the sound cell driver. We carry out a thorough examination of the nonlinear dynamics of the Bragg cell under intensity feedback for (i) dc variations of the feedback gain (β˜) and the phase shift parameter (α^ 0) and (ii) ac variations of α^ 0; total under signal encryption, investigating both from two different perspectives: (i) examining chaos in view of the …

Commentary And Interpretations Of Tagore’S 'Ode To Africa', Monish Ranjan Chatterjee

Electrical and Computer Engineering Faculty Publications

This is a commentary/interpretation of Rabindranath Tagore's poem "Ode to Africa."

Time Dynamics Of Self-Pumped Reflection Gratings In A Photorefractive Polymer, Partha P. Banerjee, S. H. Buller, C. M. Liebig, S. A. Basun, Gary Cook, Dean R. Evans, Pierre-Alexandre Blanche, J. Thomas, Cory W. Christenson, N. Peyghambarian

Electrical and Computer Engineering Faculty Publications

The time dynamics of self-pumped reflection gratings in a commonly used photorefractive polymer PDCST:PVK:ECZ-BBP:C60 with no additional electron sources or traps is investigated. While holes are normally the mobile charges and responsible for grating formation, our experimental observations, analyzed using multi-exponential fitting curves, show evidence of electrons in addition to holes as charge carriers, particularly above an applied field of 40 V/μm.

The dependence of effective carrier mobilities on the applied electric field, deduced from experimental results, show stronger field dependence of electron mobility at high electric fields. At an applied field of 70 V/μm, electron and hole mobilities become …

Digital Holographic Measurement Of Nanometric Optical Excitation On Soft Matter By Optical Pressure And Photothermal Interactions, David C. Clark

USF Tampa Graduate Theses and Dissertations

In this dissertation we use digital holographic quantitative phase microscopy to observe and measure phase-only structures due to induced photothermal interactions and nanoscopic structures produced by photomechanical interactions. Our use of the angular spectrum method combined with off-axis digital holography allows for the successful hologram acquisition and processing necessary to view these phenomena with nanometric and, in many cases, subnanometric precision. We show through applications that this has significance in metrology of bulk fluid and interfacial properties.

Our accurate quantitative phase mapping of the optically induced thermal lens in media leads to improved measurement of the absorption coefficient over existing …

Forty-Year Calibrated Record Of Earth-Reflected Radiance From Landsat: A Review, Brian L. Markham, Dennis L. Helder

United States National Aeronautics and Space Administration: Publications

Sensors on Landsat satellites have been collecting images of the Earth's surface for nearly 40 years. These images have been invaluable for characterizing and detecting changes in the land cover and land use of the world. Although initially conceived as primarily picture generating sensors, even the early sensors were radiometrically calibrated and spectrally characterized prior to launch and incorporated some capabilities to monitor their radiometric calibration once on orbit. Recently, as the focus of studies has shifted to monitoring Earth surface parameters over significant periods of time, serious attention has been focused toward bringing the data from all these sensors …

Submillisecond-Response Blue Phase Liquid Crystals For Display Applications, Kuan Ming Chen

Electronic Theses and Dissertations

With exploding growth of information exchanges between people, display has become indispensable in our daily lives. After decades of intensive research and development in materials and devices, and massive investment in manufacturing technologies, liquid crystal display (LCD) has overcome various obstacles and achieved the performance we need, such as wide viewing angle, high contrast ratio, and high resolution, etc. These excellent performances make LCD prevailed in every perspective. Recently, with the demands of energy conservation, a greener LCD with lower power consumption is desired. In order to achieve this goal, new energy-effective driving methods, such as field sequential color display, …

Image Degradation Due To Surface Scattering In The Presence Of Aberrations, Narak Choi

Electronic Theses and Dissertations

This dissertation focuses on the scattering phenomena by well-polished optical mirror surfaces. Specifically, predicting image degradation by surface scatter from rough mirror surfaces for a two-mirror telescope operating at extremely short wavelengths (9nm~30nm) is performed. To evaluate image quality, surface scatter is predicted from the surface metrology data and the point spread function in the presence of both surface scatter and aberrations is calculated. For predicting the scattering intensity distribution, both numerical and analytic methods are considered. Among the numerous analytic methods, the small perturbation method (classical Rayleigh-Rice surface scatter theory), the Kirchhoff approximation method (classical BeckmanKirchhoff surface scatter theory), …

Injection-Locked Semiconductor Lasers For Realization Of Novel Rf Photonics Components, Nazanin Hoghooghi

Electronic Theses and Dissertations

This dissertation details the work has been done on a novel resonant cavity linear interferometric modulator and a direct phase detector with channel filtering capability using injection-locked semiconductor lasers for applications in RF photonics. First, examples of optical systems whose performance can be greatly enhanced by using a linear intensity modulator are presented and existing linearized modulator designs are reviewed. The novel linear interferometric optical intensity modulator based on an injection-locked laser as an arcsine phase modulator is introduced and followed by numerical simulations of the phase and amplitude response of an injection-locked semiconductor laser. The numerical model is then …

Applications Of Volume Holographic Elements In High Power Fiber Lasers, Apurva Jain

Electronic Theses and Dissertations

The main objective of this thesis is to explore the use of volume holographic elements recorded in photo-thermo-refractive (PTR) glass for power scaling of narrow linewidth diffraction-limited fiber lasers to harness high average power and high brightness beams. Single fiber lasers enable kW level output powers limited by optical damage, thermal effects and non-linear effects. Output powers can be further scaled using large mode area fibers, however, at the cost of beam quality and instabilities due to the presence of higher order modes. The mechanisms limiting the performance of narrow-linewidth large mode area fiber lasers are investigated and solutions using …

Low Voltage Blue Phase Liquid Crystal Displays, Linghui Rao

Electronic Theses and Dissertations

From cell phones, laptops, desktops, TVs, to projectors, high reliability LCDs have become indispensable in our daily life. Tremendous progress in liquid crystal displays (LCDs) has been made after decades of extensive research and development in materials, device configurations and manufacturing technology. Nowadays, the most critical issue on viewing angle has been solved using multidomain structures and optical film compensation. Slow response time has been improved to 2-5 ms with low viscosity LC material, overdrive and undershoot voltage, and thin cell gap approach. Moving image blur has been significantly reduced by impulse driving and frame insertion. Contrast ratio in excess …

Lithographic Vertical-Cavity Surface-Emitting Lasers, Guowei Zhao

Electronic Theses and Dissertations

Remarkable improvements in vertical-cavity surface-emitting lasers (VCSELs) have been made by the introduction of mode- and current-confining oxide optical aperture now used commercially. However, the oxide aperture blocks heat flow inside the device, causing a larger thermal resistance, and the internal strain caused by the oxide can degrade device reliability, also the diffusion process used for the oxide formation can limit device uniformity and scalability. Oxide-free lithographic VCSELs are introduced to overcome these device limitations, with both the mode and current confined within the lithographically defined intracavity mesa, scaling and mass production of small size device could be possible. The …

Vertical Field Switching Blue Phase Liquid Crystals For Field Sequential Color Displays, Hui-Chuan Cheng

Electronic Theses and Dissertations

Low power consumption is a critical requirement for all liquid crystal display (LCD) devices. A field sequential color (FSC) LCD was proposed by using red (R), green (G) and blue (B) LEDs and removing the lossy component of color filters which only transmits ~30% of the incoming white light. Without color filters, FSC LCDs exhibit a ~3X higher optical efficiency and 3X higher resolution density as compared to the conventional color filters-based LCDs. However, color breakup (CBU) is a most disturbing defect that degrades the image quality in FSC displays. CBU can be observed in stationary or moving images. It …

Assessing The Feasibility Of Cosmic-Ray Acceleration By Magnetic Turbulence At The Magnetic Center, M. Fatuzzo, F. Melia

Faculty Scholarship

No abstract provided.

Multi-Wavelength Laser Sensor For Intruder Detection And Discrimination, Kavitha Venkataraayan, Sreten Askraba, Kamal E. Alameh, Clifton L. Smith

Research outputs 2011

An intruder detection and discrimination sensor with improved optical design is developed using lasers of different wavelengths to demonstrate the concept of discrimination over a distance of 6 m. A distinctive feature of optics is used to provide additional transverse laser beam scanning. The sample objects used to demonstrate the concept of discrimination over a distance of 6 m are leaf, bark, black fabric, PVC, wood and camouflage material. A camouflage material is chosen to illustrate the discrimination capability of the sensor. The sensor utilizes a five-wavelength laser combination module, which sequentially emits identically-polarized laser light beams along one optical …

Growth Analysis Of (Ag,Cu)Inse2 Thin Films Via Real Time Spectroscopic Ellipsometry, S. A. Little, V. Ranjan, R. W. Collins, S. Marsillac

Electrical & Computer Engineering Faculty Publications

In situ and ex situ characterization methods have been applied to investigate the properties of (Ag,Cu)InSe₂ (ACIS) thin films. Data acquired from real time spectroscopic ellipsometry (RTSE) experiments were analyzed to extract the evolution of the nucleating, bulk, and surface roughness layer thicknesses. The evolution of these layer thicknesses suggests a transition from Volmer-Weber to Stranski-Krastanov type behavior when Cu is replaced by Ag. The complex dielectric functions of ACIS at both deposition and room temperature as a function of film composition were also extracted from the RTSE data, enabling parameterization of the alloy optical properties.

A Study Of Wo3 And W0.95ti0.05o3 Thin Films Using Comparative Spectroscopy, James Heyward Howard

Open Access Theses & Dissertations

Tungsten oxide (WO3) is important and well-studied in materials science, particularly for sensor applications. In this research work, we consider the innovation of adding Ti to thin films of this material. Since the characteristics of any such material are strongly dependent on the conditions and methods used in its deposition, the main objective of this project is to provide a detailed spectroscopic characterization by Raman scattering, infrared absorption, and X-ray photoelectron spectroscopy (XPS) of WO3 and of W0.95Ti0.05O3. This characterization will be based on comparison of the morphology and composition of WO3-based thin films, grown by radio frequency magnetron reactive …

Optical Detection Of Melting Point Depression For Silver Nanoparticles Via In Situ Real Time Spectroscopic Ellipsometry, S. A. Little, T. Begou, R. W. Collins, S. Marsillac

Electrical & Computer Engineering Faculty Publications

Silver nanoparticle films were deposited by sputtering at room temperature and were annealed while monitoring by real time spectroscopic ellipsometry (SE). The nanoparticle dielectric functions (0.75 eV-6.5 eV) obtained by SE were modeled using Lorentz and generalized oscillators for the nanoparticle plasmon polariton (NPP) and interband transitions, respectively. The nanoparticle melting point could be identified from variations in the oscillator parameters during annealing, and this identification was further confirmed after cooling through significant, irreversible changes in these parameters relative to the as-deposited film. The variation in melting point with physical thickness, and thus average nanoparticle diameter, as measured by SE …

Introduction To Special Section On Recent Advances In The Study Of Optical Variability In The Near-Surface And Upper Ocean, T. Dickey, M. L. Banner, P. Bhandari, T. Boyd, L. Carvalho, O. Wurl

OES Faculty Publications

Optical variability occurs in the near-surface and upper ocean on very short time and space scales (e.g., milliseconds and millimeters and less) as well as greater scales. This variability is caused by solar, meteorological, and other physical forcing as well as biological and chemical processes that affect optical properties and their distributions, which in turn control the propagation of light across the air-sea interface and within the upper ocean. Recent developments in several technologies and modeling capabilities have enabled the investigation of a variety of fundamental and applied problems related to upper ocean physics, chemistry, and light propagation and utilization …

Linear-Cavity Tunable Fibre Lasers Employing An Opto-Vlsi Processor And A Mems-Based Device, David Daniel Michel

Theses: Doctorates and Masters

This thesis proposes and demonstrates experimentally two novel linear-cavity tunable fibre lasers employing an erbium-doped fibre (EDF) in conjunction with an Opto- VLSI processor and a MEMS-based device for wavelength selection. The Opto-VLSI processor and the MEMS-based device along with an optical collimator, a Bragg grating plate and an optical lens, enable the realisation of an optical filter for continuous tuning of wavelengths over the amplified spontaneous emission (ASE) range of the EDF. We also propose the use of a section of un-pumped EDF as a saturable absorber (SA), which suppresses noise spikes caused by the high optical pumping power. …

Optical Fluid-Based Photonic And Display Devices, Su Xu

Electronic Theses and Dissertations

Conventional solid-state photonic devices exhibit an ultra-high optical performance and durability, but minimal adaptability. Recently, optical fluid-based photonic and display devices are emerging. By dynamically manipulating the optical interface formed by liquids, the optical output can be reconfigured or adaptively tuned in real time. Such devices exhibit some unique characteristics that are not achievable in conventional solid-state photonic devices. Therefore, they open a gateway for new applications, such as image and signal processing, optical communication, sensing, and lab-on-a-chip, etc. Different operation principles of optical fluidbased photonic devices have been proposed, for instance fluidic pressure, electrochemistry, thermal effect, environmentally adaptive hydrogel, …

Non-Reciprocal Wave Transmission In Integrated Waveguide Array Isolators, Tony Yatming Ho

Electronic Theses and Dissertations

Non-reciprocal wave transmission is a phenomenon witnessed in certain photonic devices when the wave propagation dynamics through the device along one direction differs greatly from the dynamics along the counter-propagating direction. Specifically, it refers to significant power transfer occurring in one direction, and greatly reduced power transfer in the opposite direction. The resulting effect is to isolate the directionality of wave propagation, allowing transmission to occur along one direction only. Given the popularity of photonic integrated circuits (PIC), in which all the optical components are fabricated on the same chip so that the entire optical system can be made more …

Infrared Tapered Slot Antennas Coupled To Tunnel Diodes, Louis A. Florence

Electronic Theses and Dissertations

Tapered slot antennas (TSAs) have seen considerable application in the millimeter-wave portion of the spectrum. Desirable characteristics of TSAs include symmetric E- and H-plane antenna patterns, and broad non-resonant bandwidths. We investigate extension of TSA operation toward higher frequencies in the thermal infrared (IR), using a metal-oxide-metal diode as the detector. Several different infrared TSA design forms are fabricated using electronbeam lithography and specially developed thin-film processes. The angular antenna patterns of TSA-coupled diodes are measured at 10.6 micrometer wavelength in both E- and H-planes, and are compared to results of finite-element electromagnetic modeling using Ansoft HFSS. Parameter studies are …

High-Efficiency Blue Phase Liquid Crystal Displays, Yan Li

Electronic Theses and Dissertations

Blue phase liquid crystals (BPLCs) have a delicate lattice structure existing between chiral nematic and isotropic phases, with a stable temperature range of about 2 K. But due to short coherent length, these self-assembled nano-structured BPLCs have a fast response time. In the past three decades, the application of BPLC has been rather limited because of its narrow temperature range. In 2002, Kikuchi et al. developed a polymer stabilization method to extend the blue-phase temperature range to more than 60 K. This opens a new gateway for display and photonic applications. In this dissertation, I investigate the material properties of …

Laser Filamentation Interaction With Materials For Spectroscopic Applications, Matthew Weidman

Electronic Theses and Dissertations

Laser filamentation is a non-diffracting propagation regime consisting of an intense core that is surrounded by an energy reservoir. For laser ablation based spectroscopy techniques such as Laser Induced Breakdown Spectroscopy (LIBS), laser filamentation enables the remote delivery of high power density laser radiation at long distances. This work shows a quasiconstant filament-induced mass ablation along a 35 m propagation distance. The mass ablated is sufficient for the application of laser filamentation as a sampling tool for plasma based spectroscopy techniques. Within the scope of this study, single-shot ablation was compared with multi-shot ablation. The dependence of ablated mass on …

Fundamental Properties Of Functional Zinc Oxide Nanowires Obtained By Electrochemical Method And Their Device Applications, Athavan Nadarajah

Dissertations and Theses

We report on the fundamental properties and device applications of semiconductor nanoparticles. ZnO nanowires and CdSe quantum dots were used, prepared, characterized, and assembled into novel light-emitting diodes and solar cells. ZnO nanowire films were grown electrochemically using aqueous soluble chloride-based electrolytes as precursors at temperatures below 90° C. Dopants were added to the electrolyte in the form of chloride compounds, which are AlCl₃, CoCl₂, CuCl₂, and MnCl₂. The optical, magnetic, and structural properties of undoped and transition-metal-ion doped ZnO nanowires were explored. Our results indicate that the as-grown nanowire structures have …

Diffuse Optical Imaging Using Decomposition Methods, Binlin Wu, M. Alrubaiee, W. Cai, M. Xu, S. K. Gayen

Publications and Research

Diffuse optical imaging (DOI) for detecting and locating targets in a highly scattering turbid medium is treated as a blind source separation (BSS) problem. Three matrix decomposition methods, independent component analysis (ICA), principal component analysis (PCA), and nonnegative matrix factorization (NMF) were used to study the DOI problem. The efficacy of resulting approaches was evaluated and compared using simulated and experimental data. Samples used in the experiments included Intralipid-10% or Intralipid-20% suspension in water as the medium with absorptive or scattering targets embedded.

Direct Write Fabrication Of Waveguides And Interconnects For Optical Printed Wiring Boards, Joseph Carl Dingeldein

Dissertations, Master's Theses and Master's Reports - Open

Current copper based circuit technology is becoming a limiting factor in high speed data transfer applications as processors are improving at a faster rate than are developments to increase on board data transfer. One solution is to utilize optical waveguide technology to overcome these bandwidth and loss restrictions. The use of this technology virtually eliminates the heat and cross-talk loss seen in copper circuitry, while also operating at a higher bandwidth. Transitioning current fabrication techniques from small scale laboratory environments to large scale manufacturing presents significant challenges. Optical-to-electrical connections and out-of-plane coupling are significant hurdles in the advancement of optical …