Optics Commons^™

Temperature-Sensitive Holograms With Switchable Memory, Muhammad Irfan Dr, Suzanne Martin Dr, Izabela Naydenova Prof

Articles

Abstract

Herein, the dynamics and reversibility of temperature-induced changes in volume phase holographic gratings (VPHGs) recorded in the low-toxicity self-processing photopolymer poly(N-isopropyl acrylamide) (poly-NIPA) are reported on. Transmission and reflection gratings are exposed to temperatures ranging 8–60 °C to study the effect of temperature on their properties. First, the role of the photopolymer chemical composition is investigated by comparing layers containing NIPA with those containing acrylamide (AA) and measuring the normalized diffraction efficiency (DE) at 60 °C; higher thermal sensitivity is observed for poly-NIPA gratings (24% drop) versus low sensitivity for AA gratings (2% increase). The impact of …

Direct Multiplexing Of Low Order Aberration Modes In A Photopolymerbased Holographic Element For Analog Holographic Wavefront Sensing, Emma Branigan, Suzanne Martin, Matthew Sheehan, Kevin Murphy

Conference Papers

The fabrication of an analog holographic wavefront sensor, capable of detecting the low order defocus aberration, was achieved in an acrylamide-based photopolymer. While other implementations of holographic wavefront sensors have been carried out digitally, this process utilises a recording setup consisting only of conventional refractive elements so the cost and complexity of holographic optical element (HOE) production could be much reduced. A pair of diffraction spots, corresponding to a maximum and minimum amount of defocus, were spatially separated in the detector plane by multiplexing two HOEs with different carrier spatial frequencies. For each wavefront with a known aberration that was …

Big Data: Potential As An Ocular Epidemiology And Public Health Tool, Michael Moore

Doctoral

Refractive error is a significant cause of vision impairment both through the limited access to correction in some areas and the associated ocular diseases for which refractive errors are risk factors. Having timely, regular access to population level estimates of refractive error and vision impairment is necessary to adequately plan public health resources and resource appropriate interventions. A lack of access to current and regularly updated refractive error and vision impairment prevalence data has been identified as a significant limitation in predicting future population trends with many countries lacking any prevalence data or available data being outdated. This project addresses …

Combined Experimental And Modeling Analysis For Thedevelopment Of Optical Materials Suitable To Enhance Theimplementation Of Plasmonic-Enhanced Luminescent Down-Shifting Solutions On Existing Silicon-Based Photovoltaic Devices, James Walshe, Mihaela Girtan, Sarah Mccormack, John Doran, George Amarandei

Articles

The development of highly efficient solar collectors requires modulating the light interactions with the semiconducting materials. Incorporating luminescent species and metal nanoparticles within a semitransparent polymeric material (e.g., polymethyl methacrylate (PMMA)) leads to the formation of a plasmon-enhanced luminescent down-shifting (PLDS) layer, which offers a retrofittable approach toward expanding the wavelength range over which the conversion process can effectively occur. Adding antireflection coatings (ARCs) further controls the spectral response. However, with each additional component comes additional loss pathways. In this study, the losses related to light interactions with the PMMA and the ARCs have been investigated theoretically using a transfer …

Evaluation Of Postoperative Refractive Error Correction After Cataract Surgery, Ellen Konadu Antwi-Adjei, Emmanuel Owusu, Emmanuel Kobia-Acquah, Emmanuella Esi Dadzie, Emmanuel Anarfi, Seth Wanye

Articles

Suboptimal cataract surgery outcomes remain a challenge in most developing countries. In Ghana, about 2 million people have been reported to be blind due to cataract with about 20% new cases being recorded yearly. The aim of this study was to evaluate postoperative correction of refractive errors after cataract surgery in a selected eye hospital in Ashanti Region, Ghana. This was a retrospective study where medical records of patients (aged 40–100) who reported to an eye hospital in Ghana from 2013–2018 were reviewed. Included in the study were patients aged ≥40 years and patients with complete records. Data on patient …

Enhancing The Visibility Of Vernier Effect In A Tri-Microfiber Coupler Fiber Loop Interferometer For Ultrasensitive Refractive Index And Temperature Sensing, Fangfang Wei, Dejun Liu, Zhe Wang, Zhuochen Wang, Gerald Farrell, Qiang Wu, Gang-Ding Peng, Yuliya Semenova

Articles

In this paper a Vernier effect based sensor is analyzed and demonstrated experimentally in a tri-microfiber coupler (Tri-MFC) and polarization-maintaining fiber (PMF) loop interferometer (Tri-MFC-PMF) to provide ultrasensitive refractive index and temperature sensing. The main novelty of this work is an analysis of parameters of the proposed Tri-MFC-PMF with the objective of determining the conditions leading to a strong Vernier effect. It has been identified by simulation that the Vernier effect is a primary factor in the design of Tri-MFC-PMF loop sensing structure for sensitivity enhancement. It is furthermore demonstrated experimentally that enhancing the visibility of the Vernier spectrum in …

Nis2 As A Broadband Saturable Absorber For Ultrafast Pulse Lasers, Pengfei Wang, Han Zhang, Yu Yin, Qiuyun Ouyang, Yujin Chen, Elfed Lewis, Gerald Farrell, Masaki Tokurakawa, Sulaiman Wadi Harun, Cong Wang, Shi Li

Articles

Nickel disulfide (NiS2) has recently been found to possess strong nonlinear saturable absorption properties. This feature is highly attractive for nonlinear photonics applications. Ultrafast pulse generation is successfully demonstrated in this article for both Ytterbium- and Erbium-doped fibre lasers using micro-fibre deposited nickel disulfide (NiS2) as a saturable absorber (SA). The fabricated SA device has a modulation depth of 23% at 1.06 μm and 30.8% at 1.55 μm. Stable dissipative soliton operation was achieved at 1064.5 nm with a pulse duration of 11.7 ps and another stable conventional soliton pulse train was also obtained at 1560.2 nm with a pulse …

Intense Mid-Infrared Emission At 3.9 Μm In Ho3+-Doped Zbya Glasses For Potential Use As A Fiber Laser, Haiyan Zhao, Ruicong Wang, Xin Wang, Shijie Jia, Yaxian Fan, Elfed Lewis, Gerald Farrell, Shunbin Wang, Pengfei Wang

Articles

Intense mid-infrared emission at 3.9 µm in Ho3+-doped ZBYA glasses with direct upper laser level (Ho3+ : 5 I5) pumping at a wavelength of 888 nm is reported for the first time, to the best of our knowledge. Spectroscopic parameters were determined using the Judd–Ofelt theory and the measured absorption spectrum. The maximum emission cross section of the Ho3+-doped ZBYA glass is estimated to be 2.7 × 10−21 cm2 at 3906 nm. Additionally, fluorescence spectra and lifetimes of ZBYA glasses with different Ho3+ ion doping concentrations were measured. The results provide theoretical and experimental basis for better selection of rare-earth-doped …

Holographic Security, Vincent Toal

Books/Book Chapters

This chapter is concerned with the security applications of holographic techniques. Holograms are used in product authentication, product branding and brand protection, and personal and other documents. Serialization to ensure the uniqueness of each hologram for added security is briefly discussed. The theory of optical character recognition and joint transform correlation methods is outlined. Holographic recording using encrypted reference waves enables secure storage of information. Several methods are considered for encrypting optical data as well as holographic recording of encrypted images and their reconstruction and decryption. Millimeter and microwave holographic imaging techniques for the detection of hidden contraband, narcotics, firearms, …

Optimisation Of The Performance Of Holographic Beam-Shaping Diffractive Diffusers Through Refinement Of The Recording Process, Cara Jones, Suzanne Martin, Sanjay Keshri, Dervil Cody, Kevin Murphy

Conference Papers

Optical diffusers have uses in laser applications and machine vision. Typical fabrication at a commercial level requires master production and the stamping/copying of individual elements at scale. This expensive, indirect process inhibits custom diffusers at reasonable cost. Previously the authors published a novel, direct, single beam method of recording customizable and controllable volume holographic diffusers by manipulating laser speckle and recording the pattern in photopolymer. This method allows for beam-shaping to produce diffusion patterns of various sizes and shapes. In this work, the direct method of recording controllable holographic diffusers is refined to improve diffuser performance (i.e., a decrease in …

Simultaneous Measurement Of Displacement And Temperature Based On Two Cascaded Balloon-Like Bent Fibre Structures, Ke Tian, Ruoning Wang, Meng Zhang, Xiafan Wang, Xin Wang, Guoyong Jin, Elfed Lewis, Gerald Farrell, Pengfei Wang

Articles

A low-cost optical fibre sensor based on two cascaded balloon-like bent fibre (BBF) structures for simultaneous displacement and temperature measurement is reported. The sensor is fabricated by cascading two balloon-like bent single-mode fibres (SMFs) which with different bending radii, generating two separate interference dips within a limited wavelength range. The wavelength of the two interference dips exhibits different responses to external displacement and temperature variations, hence simultaneous measurement of displacement and temperature is realized. Experimental results show that the proposed optical fibre sensor achieves a displacement sensitivity of −318.8 pm/μm and a temperature sensitivity of 47.4 pm/°C. Taking advantage of …

High-Sensitivity Temperature Sensor Based On Anti-Resonance In High-Index Polymer-Coated Optical Fiber Interferometers, Xiaokang Lian, Qiang Wu, Gerald Farrell, Yuliya Semenova

Articles

Compared to the multimode interference (MMI) effect, the anti-resonance (AR) effect does not rely on the multimode property of the optical waveguide. This Letter shows that fiber bending can suppress the MMI and can break the superposition of AR spectra of multiple modes in a high-index polymer-coated optical fiber interferometer based on a single-mode fiber-polymer-coated no-core fiber-single-mode fiber hetero-structure. This results in the dominance of the AR spectrum of an individual mode and consequently in periodic sharp transmission dips. As a result of this phenomenon and large thermo-optical and thermal expansion coefficients of the polymer, a compact, high-sensitivity and linear …

Microfluidic Flow Direction And Rate Vector Sensor Based On A Partially Gold-Coated Tfbg, Changyu Shen, Dejun Liu, Xiaokang Lian, Tingting Lang, Chunliu Zhao, Yuliya Semenova, Jacques Albert

Articles

In microfluidic chips applications, the monitoring of the rate and the direction of a microfluidic flow is very important. Here, we demonstrate a liquid flow rate and a direction sensor using a partially gold-coated tilted fiber Bragg grating (TFBG) as the sensing element. Wavelength shifts and amplitude changes of the TFBG transmission resonances in the near infrared reveal the direction of the liquid flowing along the fiber axis in the vicinity of the TFBG due to a nanoscale gold layer over part of the TFBG. For a device length of 10 mm (and a diameter of 125 µm for easy …

Birefringent Optofluidic Gratings, Sergio Calixto, Jose L. Garcia-Cordero, Diana F. Cedillo-Alcantar, Izabela Naydenova, Guillermo Garnica

Articles

A set of parallel microfluidic channels behaving as a diffraction grating operating in the Raman-Nath regime has been fabricated and studied. The diffraction efficiency of such structure can be tuned by selecting a liquid with a particular refractive index and/or optical anisotropy. Alternatively the optical properties of the liquid can be characterised by measuring the diffraction efficiency and the state of polarization of the diffracted beam. In this work, the microfluidic channels under study have been filled with penicillin molecules dissolved in water. Due to the chirality of the penicillin, the liquid has been found to have circular birefringence of …

Stacked Volume Holographic Gratings For Extending The Operational Wavelength Range In Led And Solar Applications, Sanjay Keshri, Julia Marín-Sáez, Izabela Naydenova, Kevin Murphy, Jesús Atencia, Daniel Chemisana, Sean Garner, María-Victoria Collados, Suzanne Martin

Articles

A novel stacking procedure is presented for volume phase holographic gratings (VPHGs) recorded in photopolymer material using Corning Willow Glass as a flexible substrate in order to achieve broader angular and spectral selectivity in a diffractive device with high efficiency for solar and LED applications. For the first time to our knowledge, we have shown a device designed for use with a white LED that has the same input and output angles and high efficiency when illuminated by different wavelengths. In this paper, two VPHGs were designed, experimentally recorded, and tested when illuminated at normal incidence. The experimental approach is …

Study Of The Effect Of Magnetic Nanoparticles On The Hologram Recording Capability Of Photopolymer Nanocomposite For Development Of Holographic Sensor/Actuator, Muhammad Irfan, Suzanne Martin, Izabela Naydenova

Conference Papers

Photopolymer nanocomposite materials utilising nanoparticles of varied refractive index are one of the most attractive materials for holography due to their tuneable properties. The preparation of the photopolymer nanocomposites can involve mixing a stable colloidal suspension in the photopolymer solution or printing of the nanoparticle colloidal suspension on top of a dried photopolymer layer. By following the first approach in this study a novel photopolymer nanocomposite material is prepared for holographic recording. It consists of N-isopropylacrylamide (NIPA)-based photopolymer as a host and iron oxide magnetic nanoparticles as nanodopant. The methodology of the photopolymer nanocomposite material preparation is explained in detail. …

Development Of Photopolymer Material With Improved Dynamic Range And Sensitivity, Brian Rogers, Izabela Naydenova, Suzanne Martin

Conference Papers

In this study the effect of the concentration of acrylamide and the influence of different initiators in a photopolymer composition for holographic recording of diffraction gratings is investigated. Light manipulating Holographic Optical Elements (HOEs) have a number of characteristics which can be optimised for different roles. However, at the core of these devices is the refractive index modulation that has been created in the material during recording. Typically higher refractive index modulation will enable greater diffraction efficiency. Solar concentrating HOEs can particularly benefit from material that experiences higher refractive index modulation. For a solar concentrator to have a high acceptance …

Distribution Of Tm 3+ And Ni 2+ In Chalcogenide Glass Ceramics Containing Ga2s3 Nanocrystals: Influence On Photoluminescence Properties, Xiaosong Lu, Zhiqiang Lai, Jing Ren, Lukas Strizik, Tomas Wagner, Yanqiu Du, Gerald Farrell, Pengfei Wang

Articles

The distribution of Tm3+ and Ni2+ ions is unambiguously exhibited in 80GeS2-20Ga2S3 chalcogenide glass ceramics (GCs) containing Ga2S3 nanocrystals (NCs) by using advanced analytical transmission electron microscopy. Distinctively different distribution patterns of Tm3+ and Ni2+ ions are observed in the GCs obtained by controlled crystallization. The distribution of the dopants imposes strong influence on their optical properties which are revealed by absorption and photoluminescence (PL) spectra. Detailed discussions are given of the mechanisms of the crystallization-induced PL enhancement and quenching of the Tm3+ mid-infrared and Ni2+ near-infrared emissions, respectively.

All Fibre Q-Switched Thulium-Doped Fibre Laser Incorporating Thulium–Holmium Co-Doped Fibre As A Saturable Absorber, Shi Li, Elfed Lewis, Gerald Farrell, Ahmad Haziq Aiman Rosol, A.A. Latiff, Sulaiman Wadi Harun, Bingang Guo, Pengfei Wang

Articles

A novel all fibre Q-switched Thulium-doped fibre laser (TDFL) is reported which includes a short length of a Thulium–Holmiumco-doped fibre (THDF) as a saturable absorber. A high repetition rate (27.26 kHz) coupled with a low pulse width (19.06μs) is obtained for single wavelength Q-switched pulse operation at an output wavelength of 1911.5 nm using a pump power of 200 mW. Increasing the pump power from 200 mW to 700 mW results in the repetition rate increasing from 27.26 kHz to 99.67 kHz and the pulse width decreasing from 19.06μs to 920 ns. The centre wavelength of the single Q-switched pulse …

In-Fiber Temperature Sensor Based On Green Up-Conversion Luminescence In An Er3+-Yb3+ Co-Doped Tellurite Glass Microsphere, Meng Zhang, Angzhen Li, Jibo Yu, Xiaosong Lu, Shunbin Wang, Elfed Lewis, Gerald Farrell, Libo Yuan, Pengfei Wang

Articles

A novel, to the best of our knowledge, in-fiber temperature sensor based on green up-conversion (UC) luminescence in an Er3+-Yb3+" role="presentation" style="box-sizing: border-box; display: inline; font-size: 12.88px; line-height: normal; word-spacing: normal; overflow-wrap: normal; white-space: nowrap; float: none; direction: ltr; max-width: none; max-height: none; min-width: 0px; min-height: 0px; border: 0px; padding: 0px; margin: 0px; position: relative;">Er3+-Yb3+Er3+-Yb3+ co-doped tellurite glass microsphere is described. The tellurite glass microsphere is located firmly inside a suspended tri-core hollow-fiber (STCHF) structure. The pump light launched via a single-mode fiber (SMF) is passed through a section of multimode fiber, which is fusion spliced between the SMF …

Theoretical Analysis Of A Volume Holographic Lens Using Matlab, Sanjay Keshri, Kevin Murphy, Izabela Naydenova, Suzanne Martin

Conference Papers

Volume holographic lenses have great potential for different types of applications requiring light redirection and beam shaping such as solar light collection and LED light management. For lighting applications using LEDs, it is essential to make a highly efficient optical element to be placed in front of the LED in order to decrease energy losses. For that reason, a careful theoretical analysis of the properties and operation regime of the lens must be carried out at the design stage. The characteristics of focusing Holographic Optical Elements (HOE) depend on many factors including their thickness, spatial frequency, the angular range of …

Sensing Of Multiple Parameters With Whispering Gallery Mode Optical Fiber Micro-Resonators, Arun Kumar Mallik Dr, Vishnan Kavungal, Gerald Farrell, Yuliya Semenova

Conference Papers

Monitoring of multiple physical parameters, such as humidity, temperature, strain, concentrations of certain chemicals or gases in various environments is of great importance in many industrial applications both for minimizing adverse effects on human health as well as for maintaining production levels and quality of products. In this paper we demonstrate two different approaches to the design of multi-parametric sensors using coupled whispering gallery mode (WGM) optical fiber micro-resonators. In the first approach, a small array of micro-resonators is coupled to a single fiber taper, while in the second approach each of the micro-resonators within an array is coupled to …

Sns Optical Fiber Structure Sensor For Direct Detection Of The Phase Transition In C18h38 N-Alkane Material, Wei Han, Marek Rebow, Xiaokang Lian, Dejun Liu, Gerald Farrell, Qiang Wu, Yuliya Semenova

Articles

A singlemode-no-core-singlemode (SNS) fiber structure optical sensor for detecting the solid-liquid phase change in a phase change material: C18H38 n-alkane material (n-octadecane) is proposed and demonstrated. The transmission-type sensor probe consists of a short section of no-core fiber sandwiched between two sections of a singlemode fiber. Phase changes in n-octadecane are accompanied by large step-like variations of its refractive index (RI). Such a large discontinuous change of the n-octadecane’s RI during its phase transition, leads to the corresponding step-like change in the transmitted optical power that can reliably indicate the phase change of the sample in the vicinity of the …

Ultrabroadband Mid-Infrared Emission From Cr 2+ -Doped Infrared Transparent Chalcogenide Glass Ceramics Embedded With Thermally Grown Zns Nanorods, Xiaosong Lu, Zhiqiang Lai, Runan Zhang, Haitao Guo, Jing Ren, Lukas Strizik, Tomas Wagner, Gerald Farrell, Pengfei Wang

Articles

We report, for the first time to our knowledge, an ultrabroadband mid-infrared (MIR) emission in the range of 1800–2800 nm at room temperature from a Cr2+-doped chalcogenide glass ceramic embedded with pure hexagonal (wurtzite) β-ZnS nanorods and study the emission-dependent properties on the doping concentration of Cr2+. A new family of chalcogenide glasses based on (100 − x) Ge1.5As2S6.5 – x ZnSe (in mol.%) was prepared by melt-quenching method. The Cr2+: β-ZnS nanorods of ˜150 nm in diameter and ˜1 μm in length were grown in the Cr2+-doped glass after thermal annealing. The compositional variations of glass structures and optical …

A Twelve-Wavelength Thulium-Doped Fibre Laser Based On A Microfibre Coil Resonator Incorporating Black Phosphorus, Shi Li, Yu Yin, Elfed Lewis, Gerald Farrell, Pengfei Wang

Articles

A novel multi-wavelength continuous Thulium-doped fibre laser incorporating a microfibre coil resonator based on black phosphorus (MCR-BP) material has been successfully fabricated and demonstrated. A twelve-wavelength spectrum with 0.54 nm channel spacing has been achieved by simply adjusting the pump source power. A single peak extinction ratio of more than 40 dB was observed. The superior performance of the MCR-BP described in this article compared to conventional MCR based fibre lasers can be attributed the inclusion of the Black Phosphorous Material. The enhanced lasing is primarily due to the twin properties of the MCR-BP device combining a comb-like filter effect …

Mode Transition In Conventional Step-Index Optical Fibers, Xiaokang Lian, Gerald Farrell, Qiang Wu, Wei Han, Fangfang Wei, Yuliya Semenova

Conference Papers

The discrete self-imaging effect reveals the distinct properties of cladding modes with core modes in step-index optical fibers, as was shown in our previous work [1], where only the linearly polarized LP0n modes were studied. In this paper, the dispersion diagram of the first 17 vector modes (TE0n, TM0n, HEmn and EHmn) and the related first 9 LPmn modes are calculated by both the full-vector finite element method and the graphical method with a three-layer step-index optical fiber model. The cladding modes distributions and the transitions between the core and cladding modes are analyzed. The results of this work are …

Third-Order Optical Nonlinearity Properties Of Cdcl2-Modifed Ge–Sb–S Chalcogenide Glasses, Xiaosong Lu, Jianhui Li, Lu Yang, Runan Zhang, Yindong Zhang, Jing Ren, Aurelian Catalin Galca, Mihail Secu, Gerald Farrell, Pengfei Wang

Articles

We developed a new type of chalcohalide glasses with physicochemical and nonlinear optical properties that are tunable by composition. It is found that more than 60 mol.% CdCl2 heavy metal halide can be dissolved into the ternary Ge–Sb–S system and forming stable glasses. The visible-light transparency range is extended to shorter wavelengths with the addition of CdCl2, which is beneficial for the optical quality control and infra-red (IR) system alignment. The third-order optical nonlinearity (TONL) is studied using the femtosecond Z-scan method. The results show that both the nonlinear refractive index and two photon absorption co-efficient decrease with CdCl2. Benefiting …

Magnetic Field Sensor Based On A Tri-Microfiber Coupler Ring In Magnetic Fluid And A Fiber Bragg Grating, Fangfang Wei, Dejun Liu, Arun Kumar Mallik, Gerald Farrell, Qiang Wu, Gang-Ding Peng, Yuliya Semenova

Articles

In this paper we propose and investigate a novel magnetic field sensor based on a Tri-microfiber coupler combined with magnetic fluid and a fiber Bragg grating (FBG) in a ring. A sensitivity of 1306 pm/mT was experimentally demonstrated in the range of magnetic fields from 0 to 15 mT. The reflection peak in the output spectrum associated with the FBG serves as a reference point allowing to avoid ambiguity in determining the spectral shift induced by the magnetic field. Due to its high sensitivity at low magnetic fields, the proposed structure could be of high interest in low field biosensing …

Holographic Beam-Shaping Diffractive Diffusers Fabricated By Using Controlled Laser Speckle, Kevin Murphy, Vincent Toal, Izabela Naydenova, Suzanne Martin

Articles

A method for fabricating diffractive holographic optical diffusers is reported, allowing a high degree of control of the resulting diffuser characteristics. The method consists of recording a laser speckle pattern using a single carrier beam, with controlled speckle size and shape, in an acrylamide-based volume photopolymer. The multiple interferences that create the speckle pattern form the hologram. Results are presented verifying the diffusers are volume holographic in nature and the speckle pattern is recorded accurately in the photopolymer. Diffusers recorded by this method are analysed to characterise the optical performance of the diffusers and to illustrate their beam-shaping capabilities, particularly …

Investigation Of Temperature Response Of Photopolymer Material Used For Holographic Sensor, Muhammad Irfan, Tatsiana Mikulchyk, Suzanne Martin, Izabela Naydenova

Conference Papers

Recently, functionalised photopolymer has emerged as a versatile recording material in the field of optical holography due to its novel characteristics and potential use in the development of holographic based sensors, and optical elements. This work describes the temperature response of a newly developed photopolymer, containing of a monomer Nisopropylacrylamide (NIPA) which under photopolymerisation forms a temperature sensitive polymer - Poly(Nisopropylacrylamide) (PNIPA). The photonic sensor was developed by holographic recording of volume phase transmission gratings in a self-processing NIPA-based polymer with a 532 nm laser beam. A 633 nm probe beam was used to monitor real time diffraction efficiency (DE) …