Open Access. Powered by Scholars. Published by Universities.®

Optics Commons™

Open Access. Powered by Scholars. Published by Universities.®

Mechanical Engineering

Institution
Keyword
Publication Year
Publication
Publication Type

Articles 31 - 49 of 49

Full-Text Articles in Optics

Optical Analysis And Fabrication Of Micro And Nanoscale Plasmonically Enhanced Devices, Avery M. Hill May 2016

Optical Analysis And Fabrication Of Micro And Nanoscale Plasmonically Enhanced Devices, Avery M. Hill

Mechanical Engineering Undergraduate Honors Theses

Plasmonic nanostructures have been shown to act as optical antennas that enhance optical devices due to their ability to focus light below the diffraction limit of light and enhance the intensity of the incident light. This study focuses on computational electromagnetic (CEM) analysis of two devices: 1) GaAs photodetectors with Au interdigital electrodes and 2) Au thin-film microstructures. Experiments showed that the photoresponse of the interdigital photodetectors depend greatly on the electrode gap and the polarization of the incident light. Smaller electrode gap and transverse polarization give rise to a larger photoresponse. It was also shown that the response from …

Go to article

Particle Image Velocimetry Design & Installation, Zach Ritchie May 2016

Particle Image Velocimetry Design & Installation, Zach Ritchie

Mechanical Engineering Undergraduate Honors Theses

This work will mainly focus on the design, construction, and installation of the Particle Image Velocimetry (PIV) system in the Chemical Hazards Research Center wind tunnel. The PIV system utilizes a Class IV (double pulsed) laser, optics to produce a light sheet, timing circuitry, and a high-resolution camera (with buffered output) to measure a system’s velocity (two-dimensional) field by determining the displacement of particles over the time between laser pulses. For maximum mobility and functionality, the PIV system was installed in the center of the tunnel on a moveable cart with the laser and camera mounted to an adjustable support. …

Go to article

System And Method For Identifying Electrical Properties Of Integrate Circuits, Mary Y. Lanzerotti Jan 2016

System And Method For Identifying Electrical Properties Of Integrate Circuits, Mary Y. Lanzerotti

AFIT Patents

A new method for displaying electrical properties for integrated circuit (IC) layout designs provides for improved human visualization of those properties and comparison of as designed layout design parameters to as specified layout design parameters and to as manufactured layout parameters. The method starts with a circuitry as designed layout in a first digital format, extracts values for electrical properties from that circuitry as designed layout then annotates those values back into the first digital format. The annotated circuitry as designed layout is then converted from the first digital format to a second digital format that can be converted to …

Go to article

Dual 7-Degree-Of-Freedom Robotic Arm Remote Teleoperation Using Haptic Devices, Yu-Cheng Wang Sep 2015

Dual 7-Degree-Of-Freedom Robotic Arm Remote Teleoperation Using Haptic Devices, Yu-Cheng Wang

USF Tampa Graduate Theses and Dissertations

A teleoperated system of dual redundant manipulator will be controlled in this thesis. The robot used with the dual redundant manipulator in this thesis is Baxter. Baxter’s redundant robot arms are 7-degree-of-freedom arms. The problem that will be solved in this thesis is optimization of the 7-degree-of-freedom robot arms. The control algorithm of the 7-degree-of-freedom robot arms will be discussed and built. A simulation program will be built to test the control algorithm. Based on the control algorithm, a teleoperation system will be created for Baxter. The controller used is Omni, which is a six-joint haptic device. Omni will also …

Go to article

Simulation Studying Effects Of Multiple Primary Aberrations On Donut-Shaped Gaussian Beam, Chen Zhang, K. Wang, J. Bai, Y. Liu, Guiren Wang Jan 2013

Simulation Studying Effects Of Multiple Primary Aberrations On Donut-Shaped Gaussian Beam, Chen Zhang, K. Wang, J. Bai, Y. Liu, Guiren Wang

Faculty Publications

In this paper, we demonstrate the variation of donut-shaped depletion pattern which influenced by multiple primary aberrations. The simulation is base on a common stimulation emission of depletion (STED) system composed by Gaussian laser and vortex phase plate. The simulation results are helpful guidelines for analyzing the aberration of depletion patterns in real situations.

Go to article

Development Of A Lightweight, Monolithic, Aspheric Mirror Utlizing Fdm Technology, Josiah Thomas Oct 2012

Development Of A Lightweight, Monolithic, Aspheric Mirror Utlizing Fdm Technology, Josiah Thomas

Von Braun Symposium Student Posters

No abstract provided.

Go to article

Direct Write Fabrication Of Waveguides And Interconnects For Optical Printed Wiring Boards, Joseph Carl Dingeldein Jan 2012

Direct Write Fabrication Of Waveguides And Interconnects For Optical Printed Wiring Boards, Joseph Carl Dingeldein

Dissertations, Master's Theses and Master's Reports - Open

Current copper based circuit technology is becoming a limiting factor in high speed data transfer applications as processors are improving at a faster rate than are developments to increase on board data transfer. One solution is to utilize optical waveguide technology to overcome these bandwidth and loss restrictions. The use of this technology virtually eliminates the heat and cross-talk loss seen in copper circuitry, while also operating at a higher bandwidth. Transitioning current fabrication techniques from small scale laboratory environments to large scale manufacturing presents significant challenges. Optical-to-electrical connections and out-of-plane coupling are significant hurdles in the advancement of optical …

Go to article

Spatial Light Dilution As A Technique For Conversion Of Solar Energy To Algal Biomass, Daniel J. Dye Dec 2010

Spatial Light Dilution As A Technique For Conversion Of Solar Energy To Algal Biomass, Daniel J. Dye

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

A photobioreactor has been designed and developed to efficiently utilize solar irradiance through spatial dilution of sunlight. The concept of spatial light dilution is simple: incident sunlight is spread over a large surface area, thus reducing the photon flux density of the light. The implementation of this technique, however, is difficult. The reactor described within uses a new approach to spatial light dilution, utilizing recently-developed optical components to diffuse concentrated sunlight inside an algae culture. Preliminary productivity tests indicate a 2-3 fold increase in productivity per unit aperture (sunlight collection area) over a control reactor with direct-sunlight. Aperture productivity of …

Go to article

Near-Field Radiative Transfer: Thermal Radiation, Thermophotovoltaic Power Generation And Optical Characterization, Mathieu Francoeur Jan 2010

Near-Field Radiative Transfer: Thermal Radiation, Thermophotovoltaic Power Generation And Optical Characterization, Mathieu Francoeur

University of Kentucky Doctoral Dissertations

This dissertation focuses on near-field radiative transfer, which can be defined as the discipline concerned with energy transfer via electromagnetic waves at sub-wavelength distances. Three specific subjects related to this discipline are investigated, namely nearfield thermal radiation, nanoscale-gap thermophotovoltaic (nano-TPV) power generation and optical characterization. An algorithm for the solution of near-field thermal radiation problems in one-dimensional layered media is developed, and several tests are performed showing the accuracy, consistency and versatility of the procedure. The possibility of tuning near-field radiative heat transfer via thin films supporting surface phononpolaritons (SPhPs) in the infrared is afterwards investigated via the computation of …

Go to article

Electrically Steerable Diffraction Gratings For Hyperspectral Imaging: A Microelectromechanical System Design And Fabrication, Saban Atinc Delican Mar 2008

Electrically Steerable Diffraction Gratings For Hyperspectral Imaging: A Microelectromechanical System Design And Fabrication, Saban Atinc Delican

Theses and Dissertations

The current research is focused on the design and fabrication of an electrically programmable diffraction grating using standard micro electro mechanical systems (MEMS) technology. The goal is to design a beam steering element required to build very small hyperspectral imaging (HSI) sensors. The diffraction grating will be used to perform beam-dispersion - a critical step in the imaging process. The proposed transmissive diffraction grating based approach will minimize the overall size and the number of components in the physical design of the hyperspectral imagers, thereby enabling us to exploit the traditional advantages of MEMS such as increased reliability, smaller size, …

Go to article

Bistable Operation Of A Two-Section 1.3-Mm Inas Quantum Dot Laser—Absorption Saturation And The Quantum Confined Stark Effect, Xiaodong Huang, A. Stintz, Hua Li, Audra Rice, G. T. Liu, L.F. Lester, Julian Cheng, K.J. Malloy Mar 2001

Bistable Operation Of A Two-Section 1.3-Mm Inas Quantum Dot Laser—Absorption Saturation And The Quantum Confined Stark Effect, Xiaodong Huang, A. Stintz, Hua Li, Audra Rice, G. T. Liu, L.F. Lester, Julian Cheng, K.J. Malloy

Faculty Publications

Room temperature, continuous-wave bistability was observed in oxide-confined, two-section, 1.3- m quantum-dot (QD) lasers with an integrated intracavity quantum-dot saturable absorber. The origin of the hysteresis and bistability were shown to be due to the nonlinear saturation of the QD absorption and the electroabsorption induced by the quantum confined Stark effect.

Go to article

Control And Characterization Of Line-Addressable Micromirror Arrays, Harris J. Hall Mar 2001

Control And Characterization Of Line-Addressable Micromirror Arrays, Harris J. Hall

Theses and Dissertations

This research involved the design and implementation of a complete line-addressable control system for a 32x32 electrostatic piston-actuated micromirror array device. Line addressing reduces the number of control lines from N2 to 2N making it possible to design larger arrays and arrays with smaller element sizes. The system utilizes the electromechanical bi-stability of individual elements to bold arbitrary bi-stable phase patterns. The control system applies pulse width modulated (PWM) signals to the rows and columns of the micromirror array. Three modes of operation were conceived and built into the system. The first was the traditional signal scheme which requires …

Go to article

Microelectromechanical Optical Beam Steering Systems, David M. Burns Dec 1997

Microelectromechanical Optical Beam Steering Systems, David M. Burns

Theses and Dissertations

The development of microelectromechanical systems (MEMS) has matured to the point where the fabrication of micron sized devices is feasible. State of the art MEMS construction processes now support the fabrication of novel optical devices that could not previously be built. This dissertation reports on the development of innovative micro optical devices such as Variable Blaze Gratings (VBGs) using state of the art MEMS construction processes. The principle application of the micro optical devices described in this dissertation is steering optical beams; however other applications such as spectral analysis are identified. Specific optical beam steering systems developed and characterized in …

Go to article

Modeling And Simulation Of Optical Characteristics Of Microelectromechanical Mirror Arrays, Peter C. Roberts Dec 1996

Modeling And Simulation Of Optical Characteristics Of Microelectromechanical Mirror Arrays, Peter C. Roberts

Theses and Dissertations

MEMS (Micro-Electro-Mechanical Systems) micromirror devices can be used to control the phase of a propagating light wavefront, and in particular to correct aberrations that may be present in the wavefront, due to either atmospheric turbulence or any other type of fixed or time and space varying aberrations. In order to shorten the design cycle of MEMS micromirror devices, computer software is developed to create, from MEMS micromirror device design data, a numerical model of the MEMS device. The model is then used to compute the far field diffraction pattern of a wavefront reflected from the device, and to predict the …

Go to article

Demonstrating Optical Aberration Correction With A Mems Micro-Mirror Device, Shaun R. Hick Dec 1996

Demonstrating Optical Aberration Correction With A Mems Micro-Mirror Device, Shaun R. Hick

Theses and Dissertations

This research conducted the first demonstrated use of a micro-electro-mechanical structure (MEMS) mirror array to correct a static optical aberration. A well-developed technique in adaptive optics imaging systems uses a deformable mirror to reflect the incident wave front to the imaging stage of the system. By matching the surface of the deformable mirror to the shape of the wave front phase distortion, the reflected wave front will be less aberrated before it is imaged. Typical adaptive optics systems use piezo-electric actuated deformable mirrors. This research used an electrostatically actuated, segmented mirror array, constructed by standard MEMS fabrication techniques, to investigate …

Go to article

Design, Fabrication And Characterization Of Micro Opto-Electro-Mechanical Systems, Darren E. Sene Dec 1995

Design, Fabrication And Characterization Of Micro Opto-Electro-Mechanical Systems, Darren E. Sene

Theses and Dissertations

Several micro-opto-electro-mechanical structures were designed using the Multi-User MEMS Process (MUMPS). Specific design techniques were investigated for improving the capabilities of elevating flip up structures. The integration of several flip up microoptical structures into a microoptical system was explored with emphasis on the development of a microinterferometer. The thermal effects on the Modulus of Elasticity were determined by detecting the resonant frequency for a square Flexure Beam Micromirror Device. The resonance of the device was found to match theory to within 0.1 % and the Modulus of Elasticity was found to decrease by 0.041 GPa/K from 290 to 450 K. …

Go to article

A Fringe Center Detection Technique Based On A Sub-Pixel Resolution, And Its Applications Using Sinusoidal Gratings, Ming Chang, Paul P. Lin, Wen Chih Tai Jan 1994

A Fringe Center Detection Technique Based On A Sub-Pixel Resolution, And Its Applications Using Sinusoidal Gratings, Ming Chang, Paul P. Lin, Wen Chih Tai

Mechanical Engineering Faculty Publications

A common problem in optical profilometry is the accuracy in locating fringe centers. This paper presents an accurate fringe center detection technique based on sub-pixel resolution using the fringe projection method. An optimum reconstruction filter is developed which has low sensitivity to noise. In fringe center detection, computer simulation results of using one-pixel and sub-pixel resolutions are compared. The detection technique is then applied to radius measurement of cylindrical objects and surface profile measurement of diffuse objects. The experimental results thus obtained through the proposed optimum reconstruction filter show significant improvement in measurement accuracy.

Go to article

Development Of Strength Theories For Random Fiber Composites, Victor Giurgiutiu Jan 1994

Development Of Strength Theories For Random Fiber Composites, Victor Giurgiutiu

Faculty Publications

A ressessment of existing theories for calculating the strength of random and quasi-random fiber composites is presented. Fundamental aspects regarding the physical model, macromechanics analysis, fiber distribution functions, generalized failure criterion, and progressive versus sudden failure models are covered first. Progressive ductile failure, progressive brittle failure, and sudden brittle failure are treated in detail. In each case, the original theory is briefly reviewed, and then its extensions accompanied by numerical examples are presented. Several limitations originally imposed by Hahn, such as the monotonically nonincreasing requirement on the failure strain curve, are lifted and the mathematical formulations are generalized. Some common …

Go to article

Study Of Single-Fiber Fiber Optic Lever Microphone, Trung Duc Nguyen Jul 1993

Study Of Single-Fiber Fiber Optic Lever Microphone, Trung Duc Nguyen

Electrical & Computer Engineering Theses & Dissertations

Fiber optic sensors are widely used in today's technological applications, providing many advantages that conventional sensors lack. In particular, there is a demand in hypersonic applications to develop microphones to measure acoustic pressure that performs in high temperature and noisy surroundings. This thesis analyzes fiber optic lever microphones (FOLM), since they perform at high temperatures. An FOLM system is an intensity modulated sensor, which is simple to implement and is small in size. Two models of the FOLM have been fabricated and calibrated. The first model uses a seven-element fiber array while the second uses a single-fiber to transmit and …

Go to article

First Prev