Optics Commons^™

Highly-Sensitive Stoichiometric Analysis Of Yag Ceramics Using Laser-Induced Breakdown Spectroscopy (Libs), Jahromi, Ali Kazemi

Electronic Theses and Dissertations

Transparent ceramics are an important class of optical materials with applications in high-strength windows, radiation detectors and high-power lasers. Despite the many successful developments of the past decades, their challenging fabrication still needs to be perfected to achieve a better consistency in optical quality. In particular, ternary phase materials such as Yttrium Aluminum Garnet (YAG, Y3Al5O12), a long standing high-power laser host, require a precise control of stoichiometry, often beyond the precision of current analytical techniques, in order to reduce scattering losses and the presence of deleterious point defects. This work explores the potential of Laser-Induced Breakdown Spectroscopy (LIBS) for …

Broad Bandwidth, All-Fiber, Thulium-Doped Photonic Crystal Fiber Amplifier For Potential Use In Scaling Ultrashort Pulse Peak Powers, Alex Sincore

Electronic Theses and Dissertations

Fiber based ultrashort pulse laser sources are desirable for many applications; however generating high peak powers in fiber lasers is primarily limited by the onset of nonlinear effects such as self-phase modulation, stimulated Raman scattering, and self-focusing. Increasing the fiber core diameter mitigates the onset of these nonlinear effects, but also allows unwanted higher-order transverse spatial modes to propagate. Both large core diameters and single-mode propagation can be simultaneously attained using photonic crystal fibers. Thulium-doped fiber lasers are attractive for high peak power ultrashort pulse systems. They offer a broad gain bandwidth, capable of amplifying sub-100 femtosecond pulses. The longer …

Techniques For Characterization Of Third Order Optical Nonlinearities, Manuel Ferdinandus

Electronic Theses and Dissertations

This dissertation describes the development of novel techniques for characterization of nonlinear properties of materials. The dissertation is divided into two parts, a background and theory section and a technique development section. In the background and theory section we explain the origins of the nonlinear optical response of materials across many different spatial and temporal scales. The mechanisms that we are most interested in are the electronic nuclear and reorientational responses, which occur on the range of sub-femtosecond to several picoseconds. The electronic mechanism is due to the electrons of a material experiencing a non-parabolic potential well due a strong …

Multimaterial Fibers And Tapers A Platform For Nonlinear Photonics And Nanotechnology, Soroush Shabahang

Electronic Theses and Dissertations

The development of optical sources and components suitable for the mid-infrared is crucial for applications in this spectral range to reach the maturity level of their counterparts in the visible and near-infrared spectral regimes. The recent commercialization of quantum cascade lasers is leading to further interest in this spectral range. Wideband mid-infrared coherent sources, such as supercontinuum generation, have yet to be fully developed. A mid-infrared supercontinuum source would allow for unique applications in spectroscopy and sensing. Over the last decade, it has been shown that high-index confinement in highly nonlinear fibers pumped with high-peak-power pulses is an excellent approach …

Optics And Spectroscopy In Massive Electrodynamic Theory, Adam Caccavano

Dissertations and Theses

The kinematics and dynamics for plane wave optics are derived for a massive electrodynamic field by utilizing Proca's theory. Atomic spectroscopy is also examined, with the focus on the 21 cm radiation due to the hyperfine structure of hydrogen. The modifications to Snell's Law, the Fresnel formulas, and the 21 cm radiation are shown to reduce to the familiar expressions in the limit of zero photon mass.

Harmonic Generation In Multiresonant Plasma Films, Maria Antonietta Vincenti, Domenico De Ceglia, Joseph W. Haus, Michael Scalora

Electrical and Computer Engineering Faculty Publications

We investigate second- and third-harmonic generation in a slab of material that displays plasma resonances at the pump and its harmonic frequencies. Near-zero refractive indices and local field enhancement can deplete the pump for kW/cm² incident powers, without resorting to other resonant photonic mechanisms. We show that low-threshold, highly efficient nonlinear processes are possible in the presence of losses and phase mismatch in structures that are 10⁴ times shorter than typical nonlinear crystals, for relatively low irradiance values.

Nonlinear Dynamics Of Bragg-Domain Acousto-Optic Hybrid Feedback For First-Order Scattering Of Profiled Optical Beams, Monish Ranjan Chatterjee, Fares S. Almehmadi

Electrical and Computer Engineering Faculty Publications

A series of recent studies involving hybrid acousto-optic (AO) scattering in the Bragg domain under first-order feedback have shown the ability of the AO feedback system to encrypt, transmit and decrypt RF information applied via the sound driver. The basic premise of this operation is founded on the chaotic nature of the hybrid Bragg cell under feedback.

Investigation Of Negative Index In Dispersive, Chiral Materials Via Contra-Propagating Velocities Under Second-Order Dispersion (Gvd), Monish Ranjan Chatterjee, Tarig A. Algadey

Electrical and Computer Engineering Faculty Publications

Negative refractive index arises typically in metamaterials via multiple routes. One such avenue is the condition where the Poynting vector of the electromagnetic wave is in opposition to the group velocity in the material. An earlier work along this route in a chiral material led to the well-known result of requiring very large (non-realizable) chirality.

Thereafter, a combination of chirality together with first-order dispersion was examined using plane wave electromagnetic analysis. To arrive at the conclusions in that approach, the three wave velocities (energy, group and phase) were derived under first-order dispersion in permittivity, permeability and chirality. Negative index in …

Numerical Examination Of Acousto-Optic Bragg Interactions For Profiled Lightwaves Using A Transfer Function Formalism, Monish Ranjan Chatterjee, Fares S. Almehmadi

Electrical and Computer Engineering Faculty Publications

Classically, acousto-optic (AO) interactions comprise scattering of photons by energetic phonons into higher and lower orders. Standard weak interaction theory describes diffraction in the Bragg regime as the propagation of a uniform plane wave of light through a uniform plane wave of sound, resulting in the well-known first- and zeroth-order diffraction.

Our preliminary investigation of the nature of wave diffraction and photon scattering from a Bragg cell under intensity feedback with profiled light beams indicates that the diffracted (upshifted photon) light continues to maintain the expected (uniform plane wave) behavior versus the optical phase shift in the cell within a …

Adaptive Wiener Filter Super-Resolution Of Color Filter Array Images, Barry K. Karch, Russell C. Hardie

Electrical and Computer Engineering Faculty Publications

Digital color cameras using a single detector array with a Bayer color filter array (CFA) require interpolation or demosaicing to estimate missing color information and provide full-color images. However, demosaicing does not specifically address fundamental undersampling and aliasing inherent in typical camera designs. Fast non-uniform interpolation based super-resolution (SR) is an attractive approach to reduce or eliminate aliasing and its relatively low computational load is amenable to real-time applications. The adaptive Wiener filter (AWF) SR algorithm was initially developed for grayscale imaging and has not previously been applied to color SR demosaicing. Here, we develop a novel fast SR method …

Nanowire Metal-Insulator-Metal Plasmonic Devices, Joseph W. Haus, Li Li, Cong Deng, Nkorni Katte, Michael Scalora, Domenico De Ceglia, Maria Antonietta Vincenti

Electro-Optics and Photonics Faculty Publications

In this paper we theoretically study the responsivity of Metal-Insulator-Metal nanostructures to light illumination over a broad wavelength band (1 - 25 microns) and we examine the role of a local field enhancement and electrostatic field on the responsivity.

Femtosecond Filament Interaction As A Probe For Molecular Alignment, Erik Mckee

Electronic Theses and Dissertations

Femtosecond laser filamentation is a highly nonlinear propagation mode. When a laser pulse propagates with a peak power exceeding a critical value Pcr (5 GW at 800 nm in air), the Kerr effect tends to collapse the beam until the intensity is high enough to ionize the medium, giving rise to plasma defocusing. A dynamic competition between these two effects takes place leaving a thin and weakly ionized plasma channel in the trail of the pulse. When an ultrafast laser pulse interacts with molecules, it will align them, spinning them about their axis of polarization. As the quantum rotational wave …

Comparison Of Post-Detonation Combustion In Explosives Incorporating Aluminum Nanoparticles: Influence Of The Passivation Layer, William K. Lewis, C. G. Rumchik, M. J. Smith, K. A. Shiral Fernando, Christopher A. Crouse, Jonathan E. Spowart, Elena A. Guliants, Christopher E. Bunker

Electrical and Computer Engineering Faculty Publications

Aluminum nanoparticles and explosive formulations that incorporate them have been a subject of ongoing interest due to the potential of aluminum particles to dramatically increase energy content relative to conventional organic explosives. We have used time-resolved atomic and molecular emission spectroscopy to monitor the combustion of aluminum nanoparticles within the overall chemical dynamicsof post-detonation fireballs. We have studied the energy release dynamics of hexahydro-1,3,5-trinitro-1,3,5-triazine (RDX) charges incorporating three types of aluminum nanoparticles: commercial oxide-passivated nanoparticles, oleic acid-capped aluminum nanoparticles (AlOA), and nanoparticles in which the oxide shell of the particle has been functionalized with an acrylic monomer and copolymerized into …

External Cavity Mode-Locked Semiconductor Lasers For The Generation Of Ultra-Low Noise Multi-Gigahertz Frequency Combs And Applications In Multi-Heterodyne Detection Of Arbitrary Optical Waveforms, Josue Davila-Rodriguez

Electronic Theses and Dissertations

The construction and characterization of ultra-low noise semiconductor-based mode-locked lasers as frequency comb sources with multi-gigahertz combline-to-combline spacing is studied in this dissertation. Several different systems were built and characterized. The first of these systems includes a novel mode-locking mechanism based on phase modulation and periodic spectral filtering. This mode-locked laser design uses the same intra-cavity elements for both mode-locking and frequency stabilization to an intra-cavity, 1,000 Finesse, Fabry-Pérot Etalon (FPE). On a separate effort, a mode-locked laser based on a Slab-Coupled Optical Waveguide Amplifier (SCOWA) was built. This system generates a pulse-train with residual timing jitter of

Metrology Of Volume Chirped Bragg Gratings Recorded In Photo-Thermo-Refractive Glass For Ultrashort Pulse Stretching And Compressing, Christopher Lantigua

Electronic Theses and Dissertations

Chirped Bragg gratings (CBGs) recorded in photo-thermo-refractive (PTR) glass provide a very efficient and robust way to stretch and compress ultra-short laser pulses. These gratings offer the ability to stretch pulses from hundreds of femtoseconds, to the order of 1 ns and then recompress them. However, in order to achieve pulse stretching of this magnitude, 100 mm thick CBGs are needed. Using these CBGs to both stretch, and re-compress the pulse thus requires propagation through 200 mm of optical glass. This therefore demands perfect control of the glass homogeneity, as well as the holographic recording process of the CBG. In …

Fast-Response Liquid Crystals For Photonic And Display Applications, Jie Sun

Electronic Theses and Dissertations

Liquid crystal devices are attractive for many applications such as information displays, spatial light modulators and adaptive optics, because their optical properties are electrically tunable. However, response time of liquid crystal devices is a serious concern for many applications especially for those who require large phase modulation (≥2π). This is because a thick LC layer is usually needed to achieve a large phase shift while the response time of a nematic LC is highly determined by the cell gap.

Optically Induced Forces In Scanning Probe Microscopy, Dana Kohlgraf-Owens

Electronic Theses and Dissertations

The focus of this dissertation is the study of measuring light not by energy transfer as is done with a standard photodetector such as a photographic film or charged coupled device, but rather by the forces which the light exerts on matter. In this manner we are able to replace or complement standard photodetector-based light detection techniques. One key attribute of force detection is that it permits the measurement of light over a very large range of frequencies including those which are difficult to access with standard photodetectors, such as the far IR and THz. The dissertation addresses the specific …

High Flux Isolated Attosecond Pulse Generation, Yi Wu

Electronic Theses and Dissertations

This thesis outlines the high intensity tabletop attosecond extreme ultraviolet laser source at the Institute for the Frontier of Attosecond Science and Technology Laboratory. First, a unique Ti:Sapphire chirped pulse amplifier laser system that delivers 14 fs pulses with 300 mJ energy at a 10 Hz repetition rate was designed and built. The broadband spectrum extending from 700 nm to 900 nm was obtained by seeding a two stage Ti:Sapphire chirped pulse power amplifier with mJ-level white light pulses from a gas filled hollow core fiber. It is the highest energy level ever achieved by a broadband pulse in a …

Peak Power Scaling Of Nanosecond Pulses In Thulium Based Fiber Lasers, Christian Gaida

Electronic Theses and Dissertations

Thulium based fiber lasers represent a promising alternative for pulse energy scaling and high peak power generation with ytterbium based systems at 1µm. Advantages of thulium arise from the operation at longer wavelengths and a large gain bandwidth (1.8-2.1µm). Nonlinear effects, such as self phase modulation, stimulated Raman scattering and stimulated Brillouin scattering generally limit peak power scaling in fiber lasers. The longer wavelength of thulium fiber lasers and large mode field areas can significantly increase the nonlinear thresholds. Compared to 1µm systems, thulium fiber lasers enable single mode guidance for two times larger mode field diameter in step index …

Surface Plasmonic Lens Driven Photoelectron Source For Multi-Beam Applications, Heon Joon Choi

Legacy Theses & Dissertations (2009 - 2024)

Surface plasmon polariton (SPP) assisted photoelectron source array is proposed for use in distributed multiple electron beam lithography applications. Individual source is composed of a metal/dielectric surface structure with concentric circular grooves of subwavelength width surrounding a sub-wavelength aperture. Such optical power concentrators, called "plasmonic lenses", collect light incident over a broad area by converting it to surface electromagnetic waves, specifically SPP's, through diffraction by the sub-wavelength grooves surrounding the aperture. Through constructive interference of the generated SPPs between neighboring grooves, controlled by the periodicity of the grooves, high optical power densities can be achieved at the center of the …

Injection Locking Of Semiconductor Mode-Locked Lasers For Long-Term Stability Of Widely Tunable Frequency Combs, Charles Williams

Electronic Theses and Dissertations

Harmonically mode-locked semiconductor lasers with external ring cavities offer high repetition rate pulse trains while maintaining low optical linewidth via long cavity storage times. Single frequency injection locking generates widely-spaced and tunable frequency combs from these harmonically mode-locked lasers, while stabilizing the optical frequencies. The output is stabilized long-term with the help of a feedback loop utilizing either a novel technique based on Pound-Drever-Hall stabilization or by polarization spectroscopy. Error signals of both techniques are simulated and compared to experimentally obtained signals. Frequency combs spaced by 2.5 GHz and ~10 GHz are generated, with demonstrated optical sidemode suppression of unwanted …

Mesoscale Light-Matter Interactions, Kyle Douglass

Electronic Theses and Dissertations

Mesoscale optical phenomena occur when light interacts with a number of different types of materials, such as biological and chemical systems and fabricated nanostructures. As a framework, mesoscale optics unifies the interpretations of the interaction of light with complex media when the outcome depends significantly upon the scale of the interaction. Most importantly, it guides the process of designing an optical sensing technique by focusing on the nature and amount of information that can be extracted from a measurement. Different aspects of mesoscale optics are addressed in this dissertation which led to the solution of a number of problems in …

Fabrication Of Metallic Antenna Arrays Using Nanoimprint Lithography, Yu-Wei Lin

Electronic Theses and Dissertations

This Thesis describes the development of a cost-effective process for patterning nanoscale metal antenna arrays. Soft ultraviolet (UV) Nanoimprint Lithography (NIL) into bilayer resist was chosen since it enables repeatable large-scale replication of nanoscale patterns with good lift-off properties using a simple low-cost process. Nanofabrication often involves the use of Electron Beam Lithography (EBL) which enables the definition of nanoscale patterns on small sample regions, typically < 1 mm 2 . However its sequential nature makes the large scale production of nanostructured substrates using EBL cost-prohibitive. NIL is a pattern replication method that can reproduce nanoscale patterns in a parallel fashion, allowing the low-cost and rapid production of a large number of nanopatterned samples based on a single nanostructured master mold. Standard NIL replicates patterns by pressing a nanostructured hard mold into a soft resist layer on a substrate resulting in exposed substrate regions, followed by an optional Reactive Ion Etching (RIE) step and the subsequent deposition of e.g. metal onto the exposed substrate area. However, non-vertical sidewalls of the features in the resist layer resulting from an imperfect hard mold, from reflow of the resist layer, or from isotropic etching in the RIE step iii may cause imperfect lift-off. To overcome this problem, a bilayer resist method can be used. Using stacked resist layers with different etch rates, undercut structures can be obtained after the RIE step, allowing for easy lift-off even when using a mold with non-vertical sidewalls. Experiments were carried out using a nanostructured negative SiO2 master mold. Various material combinations and processing methods were explored. The negative master mold was transferred to a positive soft mold, leaving the original master mold unaltered. The soft mold consisted of a 5 m thick top Poly(methyl methacrylate) (PMMA), or Polyvinyl alcohol (PVA) layer, a 1.5 mm thick Polydimethylsiloxane (PDMS) buffer layer, and a glass supporting substrate. The soft mold was pressed into a bilayer of 300 nm PMMA and 350 nm of silicon based UV-curable resist that was spin-coated onto a glass slide, and cured using UV radiation. The imprinted patterns were etched using RIE, exposing the substrate, followed by metal deposition and lift-off. The experiments show that the use of soft molds enables successful pattern transfer even in the presence of small dust particles between the mold and the resist layer. Feature sizes down to 280 nm were replicated successfully

Volume Phase Masks In Photo-Thermo-Refractive Glass, Marc Segall

Electronic Theses and Dissertations

In many applications such as beam shaping, mode conversion, and phase encoding it is necessary to alter the spatial phase profile of a beam via a phase mask. Conventional techniques to accomplish this either involve surface relief profiling in thin films such as PMMA or refractive index modulation in bulk photorefractive crystals such as lithium niobate. These materials have been used extensively for the past several decades and perform admirably in low power conditions. However, in high power systems these materials will be destroyed, requiring a new means of producing phase masks. In this dissertation a method for producing robust …

Phase-Locking Stability Of A Quasi-Single-Cycle Pulse, Nathan Bodnar

Electronic Theses and Dissertations

There is increasing interest in the generation of very short laser pulses, even down to attosecond (10-18 s) durations. Laser systems with femtosecond pulse durations are needed for these applications. For many of these applications, positioning of the maximum electric field within the pulse envelope can affect the outcome. The peak of the electric field relative to the peak of the pulse is called the Carrier Envelope Phase (CEP). Controlling the position of the electric field becomes more important when pulse duration approaches single-cycle. This thesis focuses on the stabilization of a quasi-single-cycle laser facility. Improvements to this already-established laser …

Growth And Characterization Of Zno Based Semiconductor Materials And Devices, Ming Wei

Electronic Theses and Dissertations

Wide band gap semiconductors such as MgxZn1-xO represent an excellent choice for making optical photodetectors and emitters operating in the UV spectral region. High crystal and optical quality MgxZn1-xO thin films were grown epitaxially on c-plane sapphire substrates by plasma-assisted Molecular Beam Epitaxy. ZnO thin films with high crystalline quality, low defect and dislocation densities, and sub-nanometer surface roughness were achieved by applying a low temperature nucleation layer. The critical growth conditions were discussed to obtain a high quality film: the sequence of Zn and O sources for initial growth of nucleation layer, growth temperatures for both ZnO nucleation and …

Surface Plasmon Polaritons And Waveguide Modes At Structured And Inhomogeneous Surfaces, Javier Polanco

Open Access Theses & Dissertations

In chapter 1, properties of a p-polarized surface plasmon polariton are studied, propagating circumferentially around a portion of a cylindrical interface between vacuum and a metal, a situation investigated earlier by M. V. Berry (J. Phys. A: Math. Gen. 8, (1975) 1952). When the metal is convex toward the vacuum this mode is radiative and consequently is attenuated as it propagates on the cylindrical surface. An approximate analytic solution of the dispersion relation for this wave is obtained by an approach different from the one used by Berry, and plots of the real and imaginary parts of its wave number …

Mode-Division Multiplexed Transmission In Few-Mode Fibers, Neng Bai

Electronic Theses and Dissertations

As a promising candidate to break the single-mode fiber capacity limit, mode-division multiplexing (MDM) explores the spatial dimension to increase transmission capacity in fiberoptic communication. Two linear impairments, namely loss and multimode interference, present fundamental challenges to implementing MDM. In this dissertation, techniques to resolve these two issues are presented. To de-multiplex signals subject to multimode interference in MDM, Multiple-InputMultiple-Output (MIMO) processing using adaptive frequency-domain equalization (FDE) is proposed and investigated. Both simulations and experiments validate that FDE can reduce the algorithmic complexity significantly in comparison with the conventional time-domain equalization (TDE) while achieving similar performance as TDE. To further …

Development Of Thulium Fiber Lasers For High Average Power And High Peak Power Operation, Robert Sims

Electronic Theses and Dissertations

High power thulium fiber lasers are useful for a number of applications in both continuous-wave and pulsed operating regimes. The use of thulium as a dopant has recently gained interest due to its large bandwidth, possibility of high efficiency, possibility of high power and long wavelength ~1.8 – 2.1 μm. The longer emission wavelength of Tm-doped fiber lasers compared to Yb- and/or Er-doped fiber lasers creates the possibility for higher peak power operation due to the larger nonlinear thresholds and reduced nonlinear phase accumulation. One primary interest in Tm-doped fiber lasers has been to scale to high average powers; however, …

Absorptive And Refractive Optical Nonlinearities In Organic Molecules And Semiconductors, Davorin Peceli

Electronic Theses and Dissertations

The main purpose of this dissertation to investigate photophysical properties, third order nonlinearity and free carrier absorption and refraction in organic materials and semiconductors. Special emphasis of this dissertation is on characterization techniques of molecules with enhanced intersystem crossing rate and study of different approaches of increasing triplet quantum yield in organic molecules. Both linear and nonlinear characterization methods are described. Linear spectroscopic characterization includes absorption, fluorescence, quantum yield, anisotropy, and singletoxygen generation measurements. Nonlinear characterization, performed by picosecond and femtosecond laser systems (single and double pump-probe and Z-scan measurements), includes measurements of the triplet quantum yields, excited-state absorption, two-photon …