Optics Commons^™

Power Scaling Of High Power Solid State Lasers., Bumjin Oh

Electronic Theses and Dissertations

The solid-state laser is one of the most widely used lasers in scientific research and industrial applications. This thesis describes detailed investigations of two modern architectures of high power cw solid-state lasers, a 20 W diode-pumped Yb:YAG thin disc laser and 300 W diode-pumped Nd:YAG rod laser. With the thin disc laser architecture, the signal beam must fit to the pump area on the disc defined by the multi-pass diode pump configuration. The beam propagation, beam diameter, phase and thermal effects for various cavity configurations are investigated theoretically and experimentally. In addition, the internal loss, small signal gain, and thermal …

Development Of A Tabletop Coherent Soft X-Ray Source, Hanfu Kong

Electronic Theses and Dissertations

The goal of this thesis is to design a tabletop coherent soft X-ray source for attosecond high resolution imaging. We collect signals from gas cells with different length and lens with different focal length. A spectrometer with a grating and a CCD camera is applied to observe and measure the spectrum of the X-ray attosecond pulses. This thesis first introduces the theory background of ultrafast lasers, then mainly explains high harmonic generation, which is the key method for attosecond pulses generation, subsequently presents the experiment system and analyzes the results from the experiment, also compares different combinations of parameters of …

Liquid Crystal Phase Modulation For Beam Steering And Near-Eye Displays, Yun-Han Lee

Electronic Theses and Dissertations

Liquid crystal spatial phase modulator plays an important role in laser beam steering, wave-front shaping and correction, optical communication, optical computation and holography. One fundamental limitation lays in the response time of liquid crystal reorientation. To achieve fast response time, polymer-network liquid crystals are therefore proposed. By incorporating polymer network in a liquid crystal host, the response time can be reduced by a factor of 100. However, the polymer network introduces hysteresis, light scattering, and high voltage. The motivation for a fast-response liquid crystal phase modulator will be discussed in the first chapter. In the second chapter, we introduce our …

Handwritten Bangla Character Recognition Using The State-Of-The-Art Deep Convolutional Neural Networks, Md Zahangir Alom, Paheding Sidike, Mahmudul Hasan, Tarek M. Taha, Vijayan K. Asari

Electrical and Computer Engineering Faculty Publications

In spite of advances in object recognition technology, handwritten Bangla character recognition (HBCR) remains largely unsolved due to the presence of many ambiguous handwritten characters and excessively cursive Bangla handwritings. Even many advanced existing methods do not lead to satisfactory performance in practice that related to HBCR. In this paper, a set of the state-of-the-art deep convolutional neural networks (DCNNs) is discussed and their performance on the application of HBCR is systematically evaluated. The main advantage of DCNN approaches is that they can extract discriminative features from raw data and represent them with a high degree of invariance to object …

Cavity-Coupled Plasmonic Systems For Enhanced Light-Matter Interactions, Abraham Vazquez-Guardado

Electronic Theses and Dissertations

Light-matter interaction is a pivotal effect that involves the synergetic interplay of electromag- netic fields with fundamental particles. In this regard localized surface plasmons (LSP) arise from coherent interaction of the electromagnetic field with the collective oscillation of free electrons in confined sub-wavelength environments. Their most attractive properties are strong field en- hancements at the near field, highly inhomogeneous, peculiar temporal and spatial distributions and unique polarization properties. LSP systems also offer a unique playground for fundamental electromagnetic physics where micro-scale systemic properties can be studied in the macro-scale. These important properties and opportunities are brought up in this work …

Magneto-Optical Properties Of Thin Permalloy Films: A Study Of The Magneto-Optical Generation Of Light Carrying Angular Momentum, Patrick D. Montgomery

Theses and Dissertations--Electrical and Computer Engineering

Magneto-optical materials such as permalloy can be used to create artificial spin- ice (ASI) lattices with antiferromagnetic ordering. Magneto-optical materials used to create diffraction lattices are known to exhibit magnetic scattering at the half- order Bragg peak while in the ground state. The significant drawbacks of studying the magneto-optical generation of OAM using x-rays are cost, time, and access to proper equipment. In this work, it is shown that the possibility of studying OAM and magneto-optical materials in the spectrum of visible light at or around 2 eV is viable. Using spectroscopic ellipsometry it is possible to detect a change …

Thin-Film Lithium Niobate Photonics For Electro-Optics, Nonlinear Optics, And Quantum Optics On Silicon, Ashutosh Rao

Electronic Theses and Dissertations

Ion-sliced thin-film lithium niobate (LN) compact waveguide technology has facilitated the resurgence of integrated photonics based on lithium niobate. These thin-film LN waveguides offer over an order of magnitude improvement in optical confinement, and about two orders of magnitude reduction in waveguide bending radius, compared to conventional LN waveguides. Harnessing the improved confinement, a variety of miniaturized and efficient photonic devices are demonstrated in this work. First, two types of compact electrooptic modulators are presented – microring modulators, and Mach-Zehnder modulators. Next, two distinct approaches to nonlinear optical frequency converters are implemented – periodically poled lithium niobate, and mode shape …

Mode-Locked Laser Based On Large Core Yb3+-Doped Fiber, Fei Jia

Electronic Theses and Dissertations

The thesis reviews principle of laser cavity and gives a general introduction to modelocked laser (MLL). By using Yb3+-doped fiber as gain medium, passive MLL cavity is developed in experiment, aiming to obtain femtosecond pulses with high pump power from 25W to 35W. The gain medium fiber with 65µm core diameter is cleaved with one flat end and another angled. Pump laser with 976nm wavelength is coupled into Yb3+ -doped fiber to excite signal from 1020nm to 1040nm in the core. 9W is threshold for laser setup. After locking all modes, picosecond pulses are output from laser cavity and coupled …

Analysis And Design Of Non-Hermitian Optical Systems, Ali Kazemi Jahromi

Electronic Theses and Dissertations

From a very general perspective, optical devices can be viewed as constructions based on the spatial engineering of the optical index of refraction. Sculpting the real part of the refractive index produces the wide variety of known passive optical devices, such as waveguides, resonators, gratings, among a plethora of other possibilities for managing the transport of light. Less attention has been directed to engineering the imaginary part of the refractive index – that is responsible for optical gain and absorption – in conjunction with the real part of the refractive index. Optical gain is the building block of amplifiers and …

Nonlinear Dynamics In Multimode Optical Fibers, Mohammad Amin Eftekhar

Electronic Theses and Dissertations

Multimode optical fibers have recently reemerged as a viable platform for addressing a number of long-standing issues associated with information bandwidth requirements and power-handling capabilities. The complex nature of heavily multimoded systems can be effectively exploited to observe altogether novel physical effects arising from spatiotemporal and intermodal linear and nonlinear processes. Here, we have studied nonlinear dynamics in multimode optical fibers (MMFs) in both the normal and anomalous dispersion regimes. In the anomalous dispersion regime, the nonlinearity leads to a formation of spatiotemporal 3-D solitons. Unlike in single-mode fibers, these solitons are not unique and their properties can be modified …

Single Mode Wavelength-Tunable Thulium Fiber, Dong Jin Shin

Electronic Theses and Dissertations

Thulium fiber lasers have the broadest emission wavelength bandwidth out of any rare-earth doped fiber lasers. The emission wavelength starts from 1.75μm and ends at around 2.15μm, covering a vast swath of the eye safe wavelength region and intersecting with a large portion of mid-infrared atmospheric transmission window. Also, thulium fiber lasers provide the highest average output power of any other rare-earth doped fiber lasers in these wavelength regimes, making them uniquely suited for applications such as remote sensing. At the moment, high power beam propagation of continuous wave laser through the atmosphere in the mid-infrared range is yet to …

2 Micron Fiber Lasers: Power Scaling Concepts And Limitations, Alex Sincore

Electronic Theses and Dissertations

Thulium- and holmium-doped fiber lasers (TDF and HDF) emitting at 2 micron offer unique benefits and applications compared to common ytterbium-doped 1 micron lasers. This dissertation details the concepts, limitations, design, and performance of four 2 micron fiber laser systems. While these lasers were developed for various end-uses, they also provide further insight into two major power scaling limitations. The first limitation is optical nonlinearities: specifically stimulated Brillouin scattering (SBS) and modulation instability (MI). The second limitation is thermal failure due to inefficient pump conversion. First, a 21.5 W single-frequency, single-mode laser with adjustable output from continuous-wave to nanosecond pulses …

Speckle Effects In Target-In-The-Loop Laser Beam Projection Systems, Mikhail Vorontsov

Electro-Optics and Photonics Faculty Publications

In target-in-the-loop laser beam projection scenarios typical of remote sensing, directed energy, and adaptive optics applications, a transmitted laser beam propagates through an optically inhomogeneous medium toward a target, scatters off the target’s rough surface, and returns back to the transceiver plane. Coherent beam scattering off the randomly rough surface results in strong speckle modulation in the transceiver plane. This speckle modulation has been a long-standing challenge that limits performance of remote sensing, active imaging, and adaptive optics techniques. Using physics-based models of laser beam scattering off a randomly rough surface, we show that received speckle-field spatial and temporal characteristics …

Recursive Non-Local Means Filter For Video Denoising, Redha A. Ali, Russell C. Hardie

Electrical and Computer Engineering Faculty Publications

In this paper, we propose a computationally efficient algorithm for video denoising that exploits temporal and spatial redundancy. The proposed method is based on non-local means (NLM). NLM methods have been applied successfully in various image denoising applications. In the single-frame NLM method, each output pixel is formed as a weighted sum of the center pixels of neighboring patches, within a given search window.

The weights are based on the patch intensity vector distances. The process requires computing vector distances for all of the patches in the search window. Direct extension of this method from 2D to 3D, for video …

Generalized Ellipsometry On Complex Nanostructures And Low-Symmetry Materials, Alyssa Mock

Department of Electrical and Computer Engineering: Dissertations, Theses, and Student Research

In this thesis, complex anisotropic materials are investigated and characterized by generalized ellipsometry. In recent years, anisotropic materials have gained considerable interest for novel applications in electronic and optoelectronic devices, mostly due to unique properties that originate from reduced crystal symmetry. Examples include white solid-state lighting devices which have become ubiquitous just recently, and the emergence of high-power, high-voltage electronic transistors and switches in all-electric vehicles. The incorporation of single crystalline material with low crystal symmetry into novel device structures requires reconsideration of existing optical characterization approaches. Here, the generalized ellipsometry concept is extended to include applications for materials with …

Free-Space Measurements Of Dielectrics And Three-Dimensional Periodic Metamaterials, Clifford E. Kintner

Graduate Theses and Dissertations

This thesis presents the free-space measurements of a periodic metamaterial structure. The metamaterial unit cell consists of two dielectric sheets intersecting at 90 degrees. The dielectric is a polyetherimide-based material 0.001” thick. Each sheet has a copper capacitively-loaded loop (CLL) structure on the front and a cut-wire structure on the back. Foam material is used to support the unit cells. The unit cell repeats 40 times in the x-direction, 58 times in the y-direction and 5 times in the z-direction. The sample measures 12” × 12” × 1” in total. We use a free-space broadband system comprised of a pair …

Analysis Of The Joint Impact Of Atmospheric Turbulence And Refractivity On Laser Beam Propagation, Victor A. Kulikov, Mikhail Vorontsov

Electro-Optics and Photonics Faculty Publications

A laser beam propagation model that accounts for the joint effect of atmospheric turbulence and refractivity is introduced and evaluated through numerical simulations. In the numerical analysis of laser beam propagation, refractive index inhomogeneities along the atmospheric propagation path were represented by a combination of the turbulence-induced random fluctuations described in the framework of classical Kolmogorov turbulence theory and large-scale refractive index variations caused by the presence of an inverse temperature layer. The results demonstrate that an inverse temperature layer located in the vicinity of a laser beam’s propagation path may strongly impact the laser beam statistical characteristics including the …

On-Chip Training Of Memristor Crossbar Based Multi-Layer Neural Networks, Raqibul Hasan, Tarek M. Taha, Christopher Yakopcic

Electrical and Computer Engineering Faculty Publications

Memristor crossbar arrays carry out multiply-add operations in parallel in the analog domain, and so can enable neuromorphic systems with high throughput at low energy and area consumption. On-chip training of these systems have the significant advantage of being able to get around device variability and faults. This paper presents on-chip training circuits for multi-layer neural networks implemented using a single crossbar per layer and two memristors per synapse. Using two memristors per synapse provides double the synaptic weight precision when compared to a design that uses only one memristor per synapse. Proposed on-chip training system utilizes the back propagation …

Agenda: Second International Workshop On Thin Films For Electronics, Electro-Optics, Energy And Sensors (Tfe3s), University Of Dayton Research Institute

Electro-Optics and Photonics Faculty Publications

University of Dayton’s Center of Excellence for Thin Film Research and Surface Engineering (CETRASE) is delighted to organize its second international workshop at the University of Dayton’s Research Institute (UDRI) campus in Dayton, Ohio, USA. The purpose of the new workshop is to exchange technical knowledge and boost technical and educational collaboration activities within the thin film research community through our CETRASE and the UDRI.

Measuring The Reflection Matrix Of A Rough Surface, Kenneth W. Burgi, Michael A. Marciniak, Mark E. Oxley, Stephen E. Nauyoks

Faculty Publications

Phase modulation methods for imaging around corners with reflectively scattered light required illumination of the occluded scene with a light source either in the scene or with direct line of sight to the scene. The RM (reflection matrix) allows control and refocusing of light after reflection, which could provide a means of illuminating an occluded scene without access or line of sight. Two optical arrangements, one focal-plane, the other an imaging system, were used to measure the RM of five different rough-surface reflectors. Intensity enhancement values of up to 24 were achieved. Surface roughness, correlation length, and slope were examined …

Comparing Multiple Turbulence Restoration Algorithms Performance On Noisy Anisoplanatic Imagery, Michael Armand Rucci, Russell C. Hardie, Alexander J. Dapore

Electrical and Computer Engineering Faculty Publications

In this paper, we compare the performance of multiple turbulence mitigation algorithms to restore imagery degraded by atmospheric turbulence and camera noise. In order to quantify and compare algorithm performance, imaging scenes were simulated by applying noise and varying levels of turbulence. For the simulation, a Monte-Carlo wave optics approach is used to simulate the spatially and temporally varying turbulence in an image sequence. A Poisson-Gaussian noise mixture model is then used to add noise to the observed turbulence image set. These degraded image sets are processed with three separate restoration algorithms: Lucky Look imaging, bispectral speckle imaging, and a …

On The Simulation And Mitigation Of Anisoplanatic Optical Turbulence For Long Range Imaging, Russell C. Hardie, Daniel A. Lemaster

Electrical and Computer Engineering Faculty Publications

We describe a numerical wave propagation method for simulating long range imaging of an extended scene under anisoplanatic conditions. Our approach computes an array of point spread functions (PSFs) for a 2D grid on the object plane. The PSFs are then used in a spatially varying weighted sum operation, with an ideal image, to produce a simulated image with realistic optical turbulence degradation. To validate the simulation we compare simulated outputs with the theoretical anisoplanatic tilt correlation and differential tilt variance. This is in addition to comparing the long- and short-exposure PSFs, and isoplanatic angle. Our validation analysis shows an …

Block Matching And Wiener Filtering Approach To Optical Turbulence Mitigation And Its Application To Simulated And Real Imagery With Quantitative Error Analysis, Russell C. Hardie, Michael Armand Rucci, Barry K. Karch, Alexander J. Dapore

Electrical and Computer Engineering Faculty Publications

We present a block-matching and Wiener filtering approach to atmospheric turbulence mitigation for long-range imaging of extended scenes. We evaluate the proposed method, along with some benchmark methods, using simulated and real-image sequences. The simulated data are generated with a simulation tool developed by one of the authors. These data provide objective truth and allow for quantitative error analysis. The proposed turbulence mitigation method takes a sequence of short-exposure frames of a static scene and outputs a single restored image. A block-matching registration algorithm is used to provide geometric correction for each of the individual input frames. The registered frames …

Simulation Of Anisoplanatic Imaging Through Optical Turbulence Using Numerical Wave Propagation With New Validation Analysis, Russell C. Hardie, Jonathan D. Power, Daniel A. Lemaster, Douglas R. Droege, Szymon Gladysz, Santasri Bose-Pillai

Electrical and Computer Engineering Faculty Publications

We present a numerical wave propagation method for simulating imaging of an extended scene under anisoplanatic conditions. While isoplanatic simulation is relatively common, few tools are specifically designed for simulating the imaging of extended scenes under anisoplanatic conditions. We provide a complete description of the proposed simulation tool, including the wave propagation method used. Our approach computes an array of point spread functions (PSFs) for a two-dimensional grid on the object plane. The PSFs are then used in a spatially varying weighted sum operation, with an ideal image, to produce a simulated image with realistic optical turbulence degradation. The degradation …

Design Of A Hydrogen-Filled Hollow-Core Fiber Raman Laser, Yangyang Qin

Electronic Theses and Dissertations

The purpose of this study is to investigate the design of a Raman fiber laser based on a molecule hydrogen-filled hollow-core fiber with non-touching single ring of capillaries structure. O-hydrogen vibrational frequency shift of 4155 cm-1 and rotational frequency shift of 587 cm-1 were employed to generate Raman scattering from a 1064nm pump source. A thorough exploration was made to show how all Raman fiber laser components made up: gas chamber, hollow-core fibers, windows. The whole process of chamber design, modification and fabrication were demonstrated. Besides, two kinds of anti-resonant hollow-core fibers were studied and tested. The transmission and loss …

Enhancement Of Bandwidth And Laser Deflection Angle Of Acousto-Optic Deflectors By Dynamic Two-Dimensional Refractive Index Modulation, Tiansi Wang

Electronic Theses and Dissertations

Acousto-Optic Deflectors (AODs) are inertialess optical solid state devices that have advantages over conventional mechanically controlled mirror-based deflectors in numerous scientific and industrial applications. These applications include fluorescence microscopy, sensing, variable-focus lens, photolithography and laser materials processing. AODs are currently operated with a single piezoelectric transducer that modulates the refractive index only in one direction. This operating principle limits the performance of AODs to a narrow acoustic bandwidth of the transducer and a small angle of laser deflection governed by the Bragg diffraction. To overcome these two limitations, the operation of AODs with phased array ultrasonic transducers is analyzed in …

Noise, Stability, And Linewidth Performance Of 10-Ghz Optical Frequency Combs Generated From The Nested Cavity Architecture, Kristina Bagnell

Electronic Theses and Dissertations

Optical frequency combs with wide mode spacing and low timing jitter are relied upon for both time domain and frequency domain applications. It has been previously demonstrated that surrounding a low-Q semiconductor laser chip with a long external fiber cavity and inserting a high finesse Fabry–Pérot etalon into this cavity can produce a mode-locked laser with the desired high repetition rate and narrow optical mode linewidths which are of benefit to applications like photonic analog-to-digital conversion and astronomical spectrograph calibration. With this nested cavity architecture, the quality factor of the resonator is effectively determined by the product of the individual …

High Dynamic Range Display Systems, Ruidong Zhu

Electronic Theses and Dissertations

High contrast ratio (CR) enables a display system to faithfully reproduce the real objects. However, achieving high contrast, especially high ambient contrast (ACR), is a challenging task. In this dissertation, two display systems with high CR are discussed: high ACR augmented reality (AR) display and high dynamic range (HDR) display. For an AR display, we improved its ACR by incorporating a tunable transmittance liquid crystal (LC) film. The film has high tunable transmittance range, fast response time, and is fail-safe. To reduce the weight and size of a display system, we proposed a functional reflective polarizer, which can also help …

Harnessing Spatial Intensity Fluctuations For Optical Imaging And Sensing, Milad Akhlaghi Bouzan

Electronic Theses and Dissertations

Properties of light such as amplitude and phase, temporal and spatial coherence, polarization, etc. are abundantly used for sensing and imaging. Regardless of the passive or active nature of the sensing method, optical intensity fluctuations are always present! While these fluctuations are usually regarded as noise, there are situations where one can harness the intensity fluctuations to enhance certain attributes of the sensing procedure. In this thesis, we developed different sensing methodologies that use statistical properties of optical fluctuations for gauging specific information. We examine this concept in the context of three different aspects of computational optical imaging and sensing. …

Advanced Liquid Crystal Displays With Supreme Image Qualities, Haiwei Chen

Electronic Theses and Dissertations

Several metrics are commonly used to evaluate the performance of display devices. In this dissertation, we analyze three key parameters: fast response time, wide color gamut, and high contrast ratio, which affect the final perceived image quality. Firstly, we investigate how response time affects the motion blur, and then discover the 2-ms rule. With advanced low-viscosity materials, new operation modes, and backlight modulation technique, liquid crystal displays (LCDs) with an unnoticeable image blur can be realized. Its performance is comparable to an impulse-type display, like cathode ray tube (CRT). Next, we propose two novel backlight configurations to improve an LCD's …