Fluid Dynamics Commons^™

Exploring Red Palm Oil As A Sustainable Plasticizer For Carbon Black-Filled Ssbr/Br Tire Tread Compounds: A Comparative Evaluation Of Commercial Alternatives, Norma Arisanti Kinasih, Mohamad Irfan Fathurrohman, Santi Puspitasari, Dewi Kusuma Arti, Abdulhakim Masa

Journal of Materials Exploration and Findings

This study investigates the application of red palm oil (RPO) as an alternative vegetable oil resource to substitute petroleum-based plasticizers, which have environmental and health concerns, in carbon black (CB)-filled SSBR/BR tire tread compounds. The plasticizing effects of RPO were thoroughly evaluated by comparing them with a commercial bio-based plasticizer, Epoxidized Soybean Oil (ESBO), and two safer petroleum-based oils, Naphthenic Oil (NYNAS) and Treated Distillate Aromatic Extract (TDAE). The initial investigation shows that fatty acid composition is imposing regarding the plasticizing effect. The higher unsaturated fatty acid content in RPO than in ESBO improved tensile strength and degraded rolling resistance …

Metallurgical Investigation Of A Modified Eye Bolt Failure Caused By Improper Weld Extension, Specification Deviation, And Crevice Corrosion, Dimas Muhammad Fawwaz, Reza Miftahul Ulum, Johny Wahyuadi Soedarsono, Yudha Pratesa

Journal of Materials Exploration and Findings

A modified eye bolt from the David Arm Manhole Storage Tank underwent thorough metallurgical study due to the consequences of the bolt's malfunction during operation. Safety issues arose when the manhole door detached during operation. The mechanical testing and chemical composition analysis of the bolts indicated they were manufactured from an ASTM A193 Grade B7 material used for high-temperature bolting. This material did not conform to the engineering drawing, which mentioned SA 563A, which is about nuts, not bolts. This contradiction clearly shows that the eye bolt which was installed does not conform to the intended design. Welded connections of …

Rejection Of Fe (Iron) And Kmno4 (Organic Substance) Parameters In Peat Water Using Organic Membranes, Muhamad Rafli Sakti Mulia Gonera, Siti Umi Kalsum, Sarah Fiebrina Heraningsih

Journal of Materials Exploration and Findings

Peat water is a surface water source widely used by people in swampy and lowland areas, but it has poor quality characteristics such as high organic matter content, low pH, and dissolved metal levels such as iron that exceed the threshold. These conditions can cause health problems and reduce the quality of clean water so that effective treatment technology is needed. This study aims to analyze the effectiveness of ultrafiltration membranes made from chitosan from shrimp shell waste in rejecting iron (Fe) and organic substances in peat water, and to determine the effect of pressure on separation performance. This study …

Simulations Of Phugoid Motion Of Jal 123, Dereth J J. Drake Scheuermann

Georgia Journal of Science

Airplanes rely on a balance between the four forces of flight: lift, weight, thrust, and drag. If these forces are balanced, the airplane will remain stable. However, if structurally or systematically compromised, the motion can rapidly become unstable. In the aviation industry, mistakes in repairs and aircraft design can lead to accidents causing the loss of life in some cases. In this article, we will be analyzing what happened 70 Japan Airlines flight 123 and how the flight’s motion deteriorated due to a defective repair. More specifically, we will discuss the aerodynamic effects of phugoid motion and how it developed …

Modelling Of Dust Devil Flow Dynamics: Effects Of The Sharpness Parameter On Velocity And Pressure, Deepanshu Kumar, Hossein Jafari

Mathematical Modelling and Numerical Simulation with Applications

This work discusses the development of a straightforward model of dust devils, demonstrating a method for estimating wind speed and pressure. The current model incorporates momentum equations and the mass conservation equation for steady, axisymmetric, inviscid, and incompressible flow. In this model, the radial velocity is first considered, which is restricted in both the radial and axial directions. The sharpness parameter is also incorporated into the radial velocity formulation, as described by Vatistas model. Using the radial velocity as a foundation, we derive the azimuthal and axial velocities. The study further evaluates the pressure. Notably, for large values of the …

Numerical Method For Strongly Variable-Density Flows At Low Mach Number: Flame-Sheet Regularisation And A Mass-Flux Immersed Boundary Method, Matheus P. Severino, Fernando F. Fachini, Elmer M. Gennaro, Daniel Rodríguez, Leandro F. Souza

Mathematical Modelling and Numerical Simulation with Applications

A low-Mach-number flow, in the laminar regime, has intrinsically two characteristic spatial scales for a given time scale, or two characteristic temporal scales for a given spatial scale, and these dual scales are very different due to the disparity between the flow and acoustic speed. Therefore, low-Mach-number flows impose mathematical and computational challenges in their description. Standard numerical methods for compressible flows, which are typically designed for problems with a single dominant spatial and temporal scale, require alternative approaches, such as preconditioning techniques or solvers tailored for low-Mach-number equations. The present work introduces a simplified fluid dynamics model for flows …

Feasibility Analysis Of Thermal Oxidizer To Determine Remaining Life Using Fitness- For-Service Level 3 Method, Yudhi Yudistirawan, Donanta Dhaneswara, Wahyuaji Narottama Putra, Gama Widyaputra, Dewi Kurnia Suci, Agung Putra Mahardhika

Journal of Materials Exploration and Findings

An aged thermal oxidizer (TOX) in the oil and gas industry necessitates a comprehensive evaluation to ensure its continued safe operation. This study presents a Remaining Life Assessment (RLA) and a Fitness for Service (FFS) evaluation for the four main components of the TOX, in accordance with API 510, API 579/ASME FFS-1, and ASME BPVC Section VIII Div-1 standards. The investigation includes the determination of maximum stress and maximum temperature required to assess the operational viability of the reactor. The four components are radiant, convection, transition, and stack sections—were modeled using the finite element method (FEM). Following the geometric modeling, …

Fluid-Mediated Particle Transport: Revisiting Snowstorm Simulations In 2d With An Updated Pressure Calculation Algorithm, E. Maldonado, Michael W. Roth

The Compass: Earth Science Journal of Sigma Gamma Epsilon

We develop and present computer simulations of snowfall and snowfall management near buildings using deflection fins. Our approach first entails a numerical solution to the Navier – Stokes fluid dynamics equations in order to determine wind velocity profiles with and without deflection fins. Subsequent to finding the velocity field, snow particles are introduced and are subject to Newton’s Laws in order to allow transport, sticking to surfaces, landing and ultimately accumulation. We revisit previous work, presenting and discussing program construction and validation, along with cursory systematic studies of varying geometrical parameters in the simulation. The utility of the simulations is …

Taylor Dispersion In Variable-Density, Variable-Viscosity Pulsatile Flows, Prabakaran Rajamanickam, Adam D. Weiss

Progress in Scale Modeling, an International Journal

The phenomenon of Taylor or shear-induced dispersion of a non-passive scalar field in a pulsatile pipe flow is investigated, accounting for the scalar field's influence on fluid density and transport coefficients. By employing multiple scale analysis, an effective one-dimensional, unsteady mixing problem for the scalar field is obtained, which includes the diffusion coefficient for shear-induced dispersion. The resulting governing equations are applicable to a range of scalar transport problems in pulsatile pipe flows.

Analytical Study Of Transient Mixed Convective Radiative Jeffrey Fluid Flow With Diffusion–Thermo And Chemical Reaction, V. Sathiya, R. Vijayaragavan, B. Rushi Kumar

Mansoura Engineering Journal

This research examines the behavior of unsteady mixed convective radiative Jeffrey fluid flow over a permeable moving plate with a diffusion thermo effect. The study incorporates multiple factors, including aligned magnetic fields, heat generation, radiation, and chemical reactions. The behavior of Jeffrey fluid under these combined conditions is particularly relevant to the design of efficient heat exchangers, MHD generators, and cooling systems for electronic components. A regular perturbation technique was employed to solve the governing equations, yielding distributions for velocity, temperature, and species concentration. These solutions enabled the derivation of expressions for skin friction, Nusselt number, and Sherwood number. Through …

Analysis Of Leakage In Nearshore Pipelines Using Fitness For Service Method To Ensure Mechanical Integrity Based On Api-579 Level 3, Elriandri Elriandri, Dedi Priadi

Journal of Materials Exploration and Findings

The Fitness for Service (FFS) analysis is performed as a quantitative assessment to evaluate the integrity condition of a pipeline. Essentially, FFS assessment helps determine whether equipment components can operate safely despite existing deficiencies. This evaluation is carried out using the Finite Element Method (FEM). In the case of an underwater pipeline that experiences leak due to anchor pull at the flange connection, it undergoes plastic deformation and is lifted approximately 1 meter. As a mitigation step, inspection and repairs have been carried out by the company. Subsequently, modeling is performed to reconstruct the deformation process of the pipeline. Then, …

Assessment Of The Melt Quality Of A 30% Scrap Adc12 Aluminium Alloy Using The Inclusion And Fluidity Measurement Instrument (Ifmi) With Mullite Ceramic Filters, Gusti Ruri Ruri Lestari, Sandya Ananda Riswan, Muhammad Anis, Ahmad Ashari, Paramita Vidya Ayuningtyas, Bambang Suharno Prof, Donanta Dhaneswara

Journal of Materials Exploration and Findings

The increasing demand for sustainable practices in the metal casting industry has driven the use of recycled aluminum alloys such as ADC12. However, the addition of aluminum scrap tends to increase oxide inclusions, which reduce melt fluidity and compromise casting quality. This study utilizes the Inclusion and Fluidity Measurement Instrument (IFMI), equipped with mullite ceramic filters, to assess the melt quality of ADC12 aluminum alloy containing 30% scrap. Fluidity and inclusion characteristics were evaluated at five pouring temperatures (660°C, 680°C, 700°C, 720°C, and 740°C). The results show that fluidity increased with temperature, reaching a peak of 84.6 g·s⁻¹ at 740°C, …

Equipment Criticality Analysis To Determine Asset Integrity Management System Scheme In Supporting Production Optimization Scenarios In The Aeging Field, Donny Andryanto, Donanta Dhaneswara

Journal of Materials Exploration and Findings

This research investigates the production decline and cost increase in the X&Y oil and gas fields from 2022 to 2023. Production fell by 34%, while production costs per barrel rose by 79%. To address these issues, a series of optimization processes are proposed. These aim to restructure and enhance the production facilities to reduce current production costs. The optimizations include reducing pressure at the PPP Platform in 2024. Additional steps include shutting down CPP-ORF 14” pipelines and most processes at CPP 2 Platform by 2027 to convert it into an accommodation platform. Further, the plan involves optimizing the release of …

Morphological Test Of Areca Nut Fiber Ceramic Membrane Using Scanning Electron Microscopy Energy Dispersive X-Ray Mapping Spectroscopy, Amelia Marzain, Siti Umi Kalsum, Marhadi Marhadi, Ahmad Nabil Shahab

Journal of Materials Exploration and Findings

This study investigates the potential of ceramic membranes derived from areca nut fiber as a cost-effective and environmentally sustainable material for the removal of iron (Fe) and manganese (Mn) from groundwater. Two types of membranes were fabricated: one without activation and one chemically activated using 10% sodium hydroxide (NaOH). The morphological and elemental characteristics of both membranes were analyzed using Scanning Electron Microscopy (SEM) and Energy Dispersive X-ray (EDX) mapping. The concentrations of Fe and Mn before and after treatment were measured using Atomic Absorption Spectroscopy (AAS). The NaOH-activated membrane exhibited a more porous surface structure and higher oxygen content, …

Measurements Of Water-Film Thickness On Cave Walls And Speleothems, Alexandre Honiat, Salaheddine Skali-Lami, François Bourges, Bruno Lartiges

International Journal of Speleology

The water-film that coats cave walls and speleothems is a key player for the regulation of cave microclimate and the control of speleothem growth. In this paper, we demonstrate the capability of a confocal optical sensor to quantitatively measure on-site the rapid variations of water-film thickness when dripping, active condensation, or dryness occur on walls of various caves. Results obtained from a sample of four prehistoric caves and one stalagmite cave from Southwest France, indicate that the measurable thickness of water-films is generally in the 25-70 µm range for cave walls and reaches 200-300 µm on the horizontal plane of …

A Study Of Wear Measurement And Life Prediction Of Insert Chute Liner On Gold Ore Processing, Ferry Ardika Natanael, Nony Maulidya, Dedi Priadi

Journal of Materials Exploration and Findings

Chutes are critical materials handling assets to transport solid particles from one process step to another in mineral processing, coal mining and cement industries. The material transport, because of material characteristics, cause severe wear on internal lining of chutes or bins’ structure. The wear problem on internal lining of bins or chutes needs to be checked to keep production efficiency. Therefore, not checked wear rate causes liner replacement schedule becomes unpredictable. It leads to production loss and highly cost maintenance in industry. This study shows that condition-based maintenance through regular thickness measurement using Ultrasonic Transducer (UT) to predict life service …

Techno-Enviro-Economic Approach For Electrification Of Rural And Shrimp Farming Regional Development Of An Isolated Island In Indonesia By Utilizing Hybrid Renewable Energy Systems, Fiqih Akbar Wijaya, Mohammad Akita Indianto

Journal of Materials Exploration and Findings

One of the challenges in developing and archipelagic countries such as Indonesia is maintaining energy demand in rural and isolated areas due to difficulties in electrical distribution. For instance, in areas like Bawean Island, no additional electricity capacity has been introduced in the past year, leading to an unmet potential customer demand. One of the possible options is by utilizing Hybrid Renewable Energy Systems (HRES) that are integrated with existing fossil fuel-based energy systems to support the growing energy demand in the remote island. A case study in Bawean Island is conducted with the projected energy demand covers the energy …

Remaining Life Assessment And Fitness For Service Evaluation Of Aging Chemical Reactors In Polyethylene Terephthalate Resin Industry, Aditya Pahlawan Munthe, Donanta Dhaneswara, Wahyuaji Narottama Putra, Gama Widyaputra

Journal of Materials Exploration and Findings

Aging chemical reactors in the polyethylene terephthalate (PET) resin industry require comprehensive evaluation to ensure safe continued operation. This study conducts a remaining life assessment (RLA) and fitness-for-service (FFS) evaluation on five 30-year-old reactors, based on API 510, API 579/ASME FFS-1, and ASME BPVC Section VIII Div. 1 standards. The analysis involves corrosion rate measurement, future corrosion allowance (FCA) projection, and minimum thickness verification. Among the reactors, R-120 was found to have the shortest remaining life less than 15 years. FFS assessments using three criteria Average Measured Thickness, MAWP from Point Thickness Readings, and Minimum Measured Thickness confirm that R-120 …

Analysis Of Leak Testing Planning For Carbon Dioxide Piping Systems In The Development Of Carbon Capture, Utilization, And Storage Facilities In The Bintuni Basin, Devi Sentiani, Akhmad Herman Yuwono Professor

Journal of Materials Exploration and Findings

Carbon Capture, Utilization, and Storage (CCUS) technologies have become a key strategic response to global efforts to reduce CO₂ emissions. This study presents a leak testing strategy designed for a carbon dioxide (CO₂) piping system as part of a Carbon Capture, Utilization, and Storage (CCUS) project in the Bintuni Basin, West Papua, Indonesia. This study aims to ensure the system is properly prepared before commissioning by designing a leak test plan that is both practical and technical, based on ASME B31.3, ASME PCC-2, and API STD 520 Part 1. We conducted the process, which involves identifying the system boundaries, …

Assessment Of H2s-Induced Cracking Susceptibility In Steam Line Pipes And Weld Zones During Geothermal Well Construction, Riene Kaelamanda Pragitta, Yudha Pratesa

Journal of Materials Exploration and Findings

The susceptibility of steam line pipes, especially in the HAZ (heat-affected zone) and weldment areas, to hydrogen sulfide in the geothermal industry is crucial to understand from the early stages, particularly during construction. The combination of tensile stress from residual stresses after welding and metallurgical phase transformation makes the joint areas vulnerable to sulfide stress cracking. This condition becomes even more extreme when the equipment operates during the well stimulation phase. This research assesses the severity of H₂S-induced cracking using NACE MR0175 and ISO 15156-1 standards, focusing on the effects of pH and partial pressure of H₂S (p_{H₂S …}

(Si14-15) Heat Source/Sink And Chemical Reaction Effects On Micropolar Mhd Nano Fluid Flow In Stretching/Shrinking Sheet, Tejal Nagar, Harshad Patel, Akhil Mittal, Vikas Kori

Applications and Applied Mathematics: An International Journal (AAM)

This paper deals with the effects of a non-uniform heat source/sink and chemical reaction on micropolar nanofluid flow in a stretching and shrinking sheet. The flow is considered as a laminar mixed convective two-dimensional steady flow. In this flow, water is considered as a base fluid, whereas iron oxide is considered to be a conventional fluid. The governing non-linear system of PDEs are transformed into a system of ODEs using the similarity transformation, and HAM is employed for obtaining solutions. For more understanding of the effects of various physical conditions, approximate results are obtained, and expressed graphically. From the results, …

Influence Of Oil Density On Self-Propelled Motion Of Belousov-Zhabotinsky Reaction Droplet, Vivek Bharat Meshram, Anupama Sebastian, Puthiyapurayil Sibeesh, T K Shajahan

Northeast Journal of Complex Systems (NEJCS)

Belousov-Zhabotinsky reaction serves as an example of the nonlinear chemical oscillator in which the reacting substance undergoes sequential oxidation and reduction. A droplet containing the BZ reaction, when placed within the oily environment, can self-propel. In this experimental work, we explore the effect of oil medium density on the BZ reaction droplet dynamics. In an oil medium with lower density, the BZ droplet exhibits higher speed and effective diffusivity but a shorter lifetime. Both the distance and speed of the droplet initially increase with droplet volume. However, beyond a critical volume, the distance decreases while the speed stays constant. Interestingly, …

Cfd Analysis Of Hydrodynamic Cavitation Through An Orifice: Influence Of Different Inlet Pressures And Number Of Orifice Holes, Lemthong Chanphavong, Vongsavanh Chanthaboune, Keophousone Phonhalath

ASEAN Journal on Science and Technology for Development

Hydrodynamic cavitation (HC) is considered an energy-efficient process with high potential for utilization in many chemical processes. This study presents a computational fluid dynamics (CFD) analysis of cavitating flow through an orifice with a constant flow area. The Reynolds-Averaged Navier-Stokes (RANS) equations, coupled with turbulence and cavitation models, are employed to capture the complex flow behaviors. The effects of inlet pressures and number of orifice-holes on cavitation behavior are investigated. Result of the numerical simulation is validated with the existing experimental data from the literature. The CFD study revealed that cavitation initiates just behind the inlet edge of the orifice …

(R2111) Effect Of Stenotic-Aneurysmal Arterial Regime On Unsteady Magnetohydrodynamic Non-Newtonian Blood Flow With Heat Radiation, Babatunde A. Joseph, Dada M. Sunday, Bello A.J. Funsho, Akeem B. Disu, Alamu-Awoniran F., Danas James Y.

Applications and Applied Mathematics: An International Journal (AAM)

The study aims to investigate the effect of magneto-hydrodynamic on a non-Newtonian unsteady blood flow with internal heat energy in the presence of blood ironic properties characterized by stenosis. The formulated mathematical equations resulted in differential forms and were solved analytically by Differential Transform Method. The obtained solutions were displayed by graphs showing different flow physiognomies like blood velocity, temperature profile, Nusselt number, wall shear stress and stream function.

The results indicated that velocity profile increases as magnetic field, Darcy number and aneurysmal artery rise, while it decreases as heat radiation, Reynold number, and Casson parameter speedup. The temperature profile …

Impact Of Weather Systems On Uav Parameters Using Computational Fluid Dynamics, Saif Aljuhaishi, Yaseen K. Al-Timimi, Basim I. Wahab

Karbala International Journal of Modern Science

Since drones cannot fly in any kind of weather, they are not safe for time-sensitive activities. The study examines how the passage of weather systems in Iraq leads to the ban on drone flights, and how these weather conditions impact the aerodynamic forces of the drone. Hourly climate data for the study area were obtained from ECMWF ERA5 and CAMS in NetCDF format for four climate stations (Erbil, Baghdad, Rutbah, and Basrah). A ScanEagle drone was chosen for this study. The Python programming language was used to perform mathematical operations to calculate the ban on drone flights. ArcGIS 10.8 was …

Thermal Hydraulic Analysis For Different Subchannels Of Generic Vver-1200, Mosaddak Ahamed Zahid, Md. Imam Mehedi, Shamsul Arefin Shibly, A. S. Mollah

International Journal of Nuclear Security

The demand for nuclear energy is steadily increasing all over the world. Most nuclear power is used for peaceful applications such as power generation, healthcare, agriculture, food security, industry, and research. One of the primary applications of nuclear energy is the generation of electricity through nuclear power plants based on nuclear reactors. Many developing countries around the world (such as Bangladesh) are moving toward nuclear power plants because they have huge advantages, including low-cost energy, reliable energy sources, zero carbon emissions, and high energy concentration. As a result, the demand for nuclear reactor protection and operational protection of nuclear power …

(R2085) Heat And Mass Transport Characteristics In Williamson Fluid Flow Over A Permeable Stretching Cylinder, Amala Olkha, Mukesh Kumar

Applications and Applied Mathematics: An International Journal (AAM)

The intention of this research endeavor is to examine heat and mass transport in Williamson fluid flow induced by a permeable stretching cylinder in a porous medium. Various physical factors (like viscous dissipation, chemical reaction, etc.) affecting the relevant fields (flow, temperature and concentration) are incorporated in the investigation. The governing PDEs are turned into nondimensional ODEs using adequate similarity transformation relations, and then tackled numerically using MATLAB based Bvp4c technique along with shooting method. The impacts of various parameters arising in the problem are exhibited on fluid flow, temperature and concentration distribution by drawing portraits and discussed. Moreover, impressions …

Effects Of Ti Addition On The Characteristics Of Al-10zn-6mg-2si/Zro2 Composites Produced By Squeeze Casting, Qesha Diva Prameshvara, Pipin Indah Lestari, Bondan Tiara Sofyan

Journal of Materials Exploration and Findings

Metal matrix composite (MMC) with 7xxx aluminum matrix is potential for ballistic applications due to the combination of strength, toughness, and light weight. Previous study successfully produced aluminum-based composites with SiC particles which were able to stop type III bullet, however cracks remained on back of the plate. Therefore, in this research, SiC was replaced by zirconia (ZrO₂) due to its high fracture toughness. Ti-B grain refiner was added to further improve toughness through grain boundary strengthening mechanism. This research developed 5 vol.% ZrO₂ strengthened Al-10Zn-6Mg-2Si composite with addition of Al-5Ti-1B grain refiner produced through squeeze casting …

Analysis Of The Effect Of Different Surface Preparation Methods On Corrosion Resistance And Adhesion Strength Of Astm A36 Steel Substrate With Surface Tolerant Epoxy Paint As Coating Material, Irwan Wijaya Santoso, Daffa Aqila, Rini Riastuti, Rizal Tresna Ramadhani

Journal of Materials Exploration and Findings

In the industrial world, to extend the service life of materials, protection methods are carried out to slow down the material's corrosion rate. The protection method that is often used is the coating method. The coating method is a protection method by coating the substrate material using a coating material to prevent contact between the substrate material and the environment. In this research, the substrate material used is ASTM A36 steel and the coating material used is Surface Tolerant Epoxy paint. The independent variable used in this study lies in the surface preparation method which consists of: solvent cleaning, hand …

Dispersion Of Artificial Tracers In Ventilated Caves, Claudio Pastore, Eric Weber, Frédéric Doumenc, Pierre-Yves Jeannin, Marc Lütscher

International Journal of Speleology

Artificial CO₂ was used as a tracer along ventilated karst conduits to infer airflow and investigate tracer dispersion. In the karst vadose zone, cave ventilation is an efficient mode of transport for heat, gases and aerosols and thus drives the spatial distribution of airborne particles. Modelling this airborne transport requires geometrical and physical parameters of the conduit system, including the cross-sectional areas, the airflow and average air speed, as well as the longitudinal dispersion coefficient which describes the spreading of a solute. Four gauging tests were carried out in one mine (artificial conduit) and two ventilated caves (natural conduits). …